&uart1 {
	status = "disabled";
	current-speed = <115200>;
};

&uart3 {
	status = "okay";
	current-speed = <115200>;
    pinctrl-0 = <&uart3_default>;
	pinctrl-1 = <&uart3_sleep>;
	pinctrl-names = "default", "sleep";
};

&uart2 {
	status = "okay";
	hw-flow-control;
	current-speed = <9600>;
    pinctrl-0 = <&uart2_default>;
	pinctrl-1 = <&uart2_sleep>;
	pinctrl-names = "default", "sleep";
};




&pinctrl {
	uart3_default: uart3_default {
		group1 {
			psels = <NRF_PSEL(UART_TX, 1, 10)>;
		};
		group2 {
			psels = <NRF_PSEL(UART_RX, 1, 11)>;
			bias-pull-up;
		};
	};

	uart3_sleep: uart3_sleep {
		group1 {
			psels = <NRF_PSEL(UART_TX, 1, 10)>,
				<NRF_PSEL(UART_RX, 1, 11)>;
			low-power-enable;
		};
	};

	uart2_default: uart2_default {
		group1 {
			psels = <NRF_PSEL(UART_TX, 1, 6)>;
			

		};
		group2 {
			psels = <NRF_PSEL(UART_RX, 1, 7)>;
			bias-pull-up;
		};
	};

	uart2_sleep: uart2_sleep {
		group1 {
			psels = <NRF_PSEL(UART_TX, 1, 6)>,
				<NRF_PSEL(UART_RX, 1, 7)>;
			low-power-enable;
		};
	};

	i2c1_default: i2c1_default {
		group1 {
			psels = <NRF_PSEL(TWIM_SDA, 1, 12)>,
				<NRF_PSEL(TWIM_SCL, 1, 13)>;
			bias-pull-up;

		};
	};


	spi4_default: spi4_default {
		group1 {
			psels = <NRF_PSEL(SPIM_SCK, 0, 28)>,
				<NRF_PSEL(SPIM_MISO, 0, 24)>,
				<NRF_PSEL(SPIM_MOSI, 0, 23)>;
		};
	};
  varicite_reset_pin: varicite_reset_pin{
        compatible = "nordic,gpio-pins";
        gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
        status = "okay";
    };

};



&spi4 {
	

	cs-gpios = <&gpio0 29 GPIO_ACTIVE_LOW>, <&gpio0 29 GPIO_ACTIVE_LOW>, <&gpio0 29 GPIO_ACTIVE_LOW>;
	clock-frequency = <100000>;


	adxl362: adxl362@0 {
		compatible = "adi,adxl362";
		spi-max-frequency = <8000000>;
		reg = <0>;
		int1-gpios = <&gpio0 9 0>;
	};

	bme280: bme280@1 {
		compatible = "bosch,bme280";
		reg = <1>;
		spi-max-frequency = <1000000>; 
	};

};



&i2c1 {
	status = "okay";
	pinctrl-0 = <&i2c1_default>;
	pinctrl-names = "default", "sleep";
};



&arduino_header {
    status = "disabled";
};
&gpio_fwd {
    status = "disabled";
};