[00:03:03.470,001] app_coordinator_original: Network steering finished [00:03:03.470,458] zigbee_app_utils: Unimplemented signal (signal: 54, sta tus: 0) uart:~$ [00:00:00.001,953] ieee802154_nrf5: nRF5 802154 radio initialized *** Booting nRF Connect SDK v2.5.1 *** [00:00:00.012,939] main: Router started successfully [00:00:00.012,939] main: RESET [00:00:00.012,969] main: get_reset_reason: Reset cause is: RESET_PIN [00:00:00.694,671] zigbee_shell: Register ZCL ctx at Zigbee device to use Zigbee shell ZCL commands. [00:00:00.694,702] main: SIGNAL 23 , state not OK [00:00:00.694,732] zigbee_app_utils: Production configuration is not present or invalid (status: -1) [00:00:00.695,098] main: SIGNAL 1 , state OK [00:00:00.695,098] zigbee_app_utils: Zigbee stack initialized [00:00:00.699,493] main: SIGNAL 5: Device started for the first time after the NVRAM erase [00:00:00.699,493] zigbee_app_utils: Device started for the first time [00:00:00.699,523] zigbee_app_utils: Start network steering [00:00:00.699,523] zigbee_app_utils: Started network rejoin procedure. uart:~$ bdb bdb bdb - Base device behaviour manipulation. Subcommands: channel :Set/get channel. Usage: channel [] If n is [11:26], set to that channel. Otherwise, treat n as bitmask. child_max :Set max_child number. Usage: child_max extpanid :Set/get extpanid. Usage: extpanid [] factory_reset :Perform factory reset. ic :Install code manipulation. legacy :Get legacy mode. nwkkey :Set network key. Usage: nwkkey panid :Set/get panid. Usage: panid [] role :Set/get role. start :Start commissionning. uart:~$ zdo zdo zdo - ZDO manipulation. Subcommands: active_ep :Send active endpoint request. Usage: active_ep simple_desc_req :Send simple descriptor request. Usage: simple_desc_req match_desc :Send match descriptor request. Usage: match_desc [ ...] [ ...] [-t | --timeout d:number of seconds to wait for answers] nwk_addr :Resolve EUI64 address to short network address. Usage: nwk_addr ieee_addr :Resolve network short address to EUI64 address. Usage: ieee_addr eui64 :Get/set the eui64 address of the node. Usage: eui64 [] short :Get the short address of the node. bind :Create/remove the binding entry in the remote node. mgmt_bind :Get binding table (see spec. 2.4.3.3.4) Usage: [d:start_index] mgmt_leave :Perform mgmt_leave_req (see spec. 2.4.3.3.5) Usage: mgmt_leave [h:device_address eui64] [--children] [--rejoin] --children - Device should also remove its children when leaving. --rejoin - Device should rejoin network after leave. mgmt_lqi :Perform mgmt_lqi request. Usage: mgmt_lqi [d:start index] [00:00:42.232,818] main: SIGNAL 10: BDB network steering completed [00:00:42.232,849] zigbee_app_utils: Network steering was not successful (status: -1) uart:~$ zdo eui64 zdo eui64 f4ce361fccb346a2 Done [00:01:00.439,575] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:01:00.439,605] main: display_counters: Uart frames: Tx 0, Rx 0 [00:01:24.767,059] main: SIGNAL 10: BDB network steering completed [00:01:24.767,089] zigbee_app_utils: Network steering was not successful (status: -1) uart:~$ [00:00:00.002,166] ieee802154_nrf5: nRF5 802154 radio initialized *** Booting nRF Connect SDK v2.5.1 *** [00:00:00.013,122] main: Router started successfully [00:00:00.013,153] main: RESET [00:00:00.013,153] main: get_reset_reason: Reset cause is: RESET_PIN [00:00:00.694,885] zigbee_shell: Register ZCL ctx at Zigbee device to use Zigbee shell ZCL commands. [00:00:00.694,915] main: SIGNAL 23 , state not OK [00:00:00.694,946] zigbee_app_utils: Production configuration is not present or invalid (status: -1) [00:00:00.695,312] main: SIGNAL 1 , state OK [00:00:00.695,312] zigbee_app_utils: Zigbee stack initialized [00:00:00.699,676] main: SIGNAL 5: Device started for the first time after the NVRAM erase [00:00:00.699,707] zigbee_app_utils: Device started for the first time [00:00:00.699,707] zigbee_app_utils: Start network steering [00:00:00.699,737] zigbee_app_utils: Started network rejoin procedure. [00:00:42.233,062] main: SIGNAL 10: BDB network steering completed [00:00:42.233,093] zigbee_app_utils: Network steering was not successful (status: -1) [00:01:00.439,575] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:01:00.439,605] main: display_counters: Uart frames: Tx 0, Rx 0 [00:01:24.766,906] main: SIGNAL 10: BDB network steering completed [00:01:24.766,937] zigbee_app_utils: Network steering was not successful (status: -1) [00:02:00.656,341] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:02:00.656,372] main: display_counters: Uart frames: Tx 0, Rx 0 [00:02:09.275,054] main: SIGNAL 10: BDB network steering completed [00:02:09.275,085] zigbee_app_utils: Network steering was not successful (status: -1) [00:02:57.761,047] main: SIGNAL 10: BDB network steering completed [00:02:57.761,077] zigbee_app_utils: Network steering was not successful (status: -1) [00:03:00.660,766] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:03:00.660,797] main: display_counters: Uart frames: Tx 0, Rx 0 [00:03:54.218,048] main: SIGNAL 10: BDB network steering completed [00:03:54.218,078] zigbee_app_utils: Network steering was not successful (status: -1) [00:04:00.661,071] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:04:00.661,102] main: display_counters: Uart frames: Tx 0, Rx 0 [00:05:01.074,340] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:05:01.074,371] main: display_counters: Uart frames: Tx 0, Rx 0 [00:05:06.633,026] main: SIGNAL 10: BDB network steering completed [00:05:06.633,087] zigbee_app_utils: Network steering was not successful (status: -1) [00:06:01.076,660] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:06:01.076,690] main: display_counters: Uart frames: Tx 0, Rx 0 [00:06:50.902,038] main: SIGNAL 10: BDB network steering completed [00:06:50.902,069] zigbee_app_utils: Network steering was not successful (status: -1) [00:07:01.080,627] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:07:01.080,657] main: display_counters: Uart frames: Tx 0, Rx 0 [00:08:01.085,266] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:08:01.085,296] main: display_counters: Uart frames: Tx 0, Rx 0 [00:09:01.437,316] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:09:01.437,347] main: display_counters: Uart frames: Tx 0, Rx 0 [00:09:38.927,032] main: SIGNAL 10: BDB network steering completed [00:09:38.927,062] zigbee_app_utils: Network steering was not successful (status: -1) [00:10:01.442,687] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:10:01.442,718] main: display_counters: Uart frames: Tx 0, Rx 0 [00:11:01.447,601] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:11:01.447,631] main: display_counters: Uart frames: Tx 0, Rx 0 [00:12:01.448,394] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:12:01.448,425] main: display_counters: Uart frames: Tx 0, Rx 0 [00:13:01.452,819] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:13:01.452,850] main: display_counters: Uart frames: Tx 0, Rx 0 [00:14:01.500,335] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:14:01.500,366] main: display_counters: Uart frames: Tx 0, Rx 0 [00:14:34.446,044] main: SIGNAL 10: BDB network steering completed [00:14:34.446,075] zigbee_app_utils: Network steering was not successful (status: -1) [00:15:01.503,936] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:15:01.503,967] main: display_counters: Uart frames: Tx 0, Rx 0 [00:16:01.507,446] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:16:01.507,476] main: display_counters: Uart frames: Tx 0, Rx 0 [00:17:01.510,467] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:17:01.510,498] main: display_counters: Uart frames: Tx 0, Rx 0 [00:18:01.514,678] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:18:01.514,709] main: display_counters: Uart frames: Tx 0, Rx 0 [00:19:01.516,387] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:19:01.516,418] main: display_counters: Uart frames: Tx 0, Rx 0 [00:20:01.519,500] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:20:01.519,531] main: display_counters: Uart frames: Tx 0, Rx 0 [00:21:01.520,141] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:21:01.520,202] main: display_counters: Uart frames: Tx 0, Rx 0 [00:22:01.525,695] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:22:01.525,726] main: display_counters: Uart frames: Tx 0, Rx 0 [00:23:01.527,008] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:23:01.527,038] main: display_counters: Uart frames: Tx 0, Rx 0 [00:23:44.971,069] main: SIGNAL 10: BDB network steering completed [00:23:44.971,099] zigbee_app_utils: Network steering was not successful (status: -1) [00:24:01.530,578] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:24:01.530,609] main: display_counters: Uart frames: Tx 0, Rx 0 [00:25:01.532,775] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:25:01.532,806] main: display_counters: Uart frames: Tx 0, Rx 0 [00:26:01.535,125] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:26:01.535,156] main: display_counters: Uart frames: Tx 0, Rx 0 [00:27:01.539,581] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:27:01.539,611] main: display_counters: Uart frames: Tx 0, Rx 0 [00:28:01.541,656] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:28:01.541,687] main: display_counters: Uart frames: Tx 0, Rx 0 [00:29:01.542,022] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:29:01.542,053] main: display_counters: Uart frames: Tx 0, Rx 0 [00:30:01.543,121] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:30:01.543,151] main: display_counters: Uart frames: Tx 0, Rx 0 [00:31:01.548,919] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:31:01.548,950] main: display_counters: Uart frames: Tx 0, Rx 0 [00:32:01.553,131] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:32:01.553,161] main: display_counters: Uart frames: Tx 0, Rx 0 [00:33:01.554,046] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:33:01.554,077] main: display_counters: Uart frames: Tx 0, Rx 0 [00:34:01.559,936] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:34:01.559,967] main: display_counters: Uart frames: Tx 0, Rx 0 [00:35:01.563,262] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:35:01.563,293] main: display_counters: Uart frames: Tx 0, Rx 0 [00:36:01.565,704] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:36:01.565,734] main: display_counters: Uart frames: Tx 0, Rx 0 [00:37:01.568,359] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:37:01.568,389] main: display_counters: Uart frames: Tx 0, Rx 0 uart:~$ [00:00:00.001,647] ieee802154_nrf5: nRF5 802154 radio initialized *** Booting nRF Connect SDK v2.5.1 *** [00:00:00.011,383] main: Router started successfully [00:00:00.011,383] main: RESET [00:00:00.011,413] main: get_reset_reason: Reset cause is: RESET_PIN [00:00:00.693,054] zigbee_shell: Register ZCL ctx at Zigbee device to use Zigbee shell ZCL commands. [00:00:00.693,084] main: SIGNAL 23 , state not OK [00:00:00.693,115] zigbee_app_utils: Production configuration is not present or invalid (status: -1) [00:00:00.693,481] main: SIGNAL 1 , state OK [00:00:00.693,511] zigbee_app_utils: Zigbee stack initialized [00:00:00.697,967] main: SIGNAL 5: Device started for the first time after the NVRAM erase [00:00:00.697,967] zigbee_app_utils: Device started for the first time [00:00:00.697,998] zigbee_app_utils: Start network steering [00:00:00.697,998] zigbee_app_utils: Started network rejoin procedure. [00:00:42.232,513] main: SIGNAL 10 , state not OK [00:00:42.232,543] main: count ZB_BDB_SIGNAL_STEERING 1 [00:00:42.232,574] zigbee_app_utils: Network steering was not successful (status: -1) [00:01:00.439,117] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:01:00.439,147] main: display_counters: Uart frames: Tx 0, Rx 0 [00:01:24.766,540] main: SIGNAL 10 , state not OK [00:01:24.766,601] main: count ZB_BDB_SIGNAL_STEERING 2 [00:01:24.766,601] zigbee_app_utils: Network steering was not successful (status: -1) [00:02:00.656,341] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:02:00.656,372] main: display_counters: Uart frames: Tx 0, Rx 0 [00:02:09.274,536] main: SIGNAL 10 , state not OK [00:02:09.274,566] main: count ZB_BDB_SIGNAL_STEERING 3 [00:02:09.274,597] main: parnet_node 0xffff [00:02:09.274,597] main: reset zb_bdb_reset_via_local_action 3 [00:02:09.274,627] zigbee_app_utils: Network steering was not successful (status: -1) [00:02:09.295,440] main: SIGNAL 3: The device has left the network [00:02:09.295,440] zigbee_app_utils: Network left (leave type: 0) [00:02:57.760,559] main: SIGNAL 10 , state not OK [00:02:57.760,589] main: count ZB_BDB_SIGNAL_STEERING 1 [00:02:57.760,620] zigbee_app_utils: Network steering was not successful (status: -1) [00:03:00.661,315] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:03:00.661,346] main: display_counters: Uart frames: Tx 0, Rx 0 [00:04:01.037,322] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:04:01.037,353] main: display_counters: Uart frames: Tx 0, Rx 0 [00:04:10.159,515] main: SIGNAL 10 , state not OK [00:04:10.159,545] main: count ZB_BDB_SIGNAL_STEERING 2 [00:04:10.159,576] zigbee_app_utils: Network steering was not successful (status: -1) [00:05:01.041,015] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:05:01.041,046] main: display_counters: Uart frames: Tx 0, Rx 0 [00:05:54.429,534] main: SIGNAL 10 , state not OK [00:05:54.429,565] main: count ZB_BDB_SIGNAL_STEERING 3 [00:05:54.429,595] main: parnet_node 0xffff [00:05:54.429,595] main: reset zb_bdb_reset_via_local_action 3 [00:05:54.429,626] zigbee_app_utils: Network steering was not successful (status: -1) [00:05:54.450,439] main: SIGNAL 3: The device has left the network [00:05:54.450,439] zigbee_app_utils: Network left (leave type: 0) [00:06:01.044,372] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:06:01.044,372] main: display_counters: Uart frames: Tx 0, Rx 0 [00:07:01.048,675] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:07:01.048,706] main: display_counters: Uart frames: Tx 0, Rx 0 [00:08:01.051,239] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:08:01.051,269] main: display_counters: Uart frames: Tx 0, Rx 0 [00:08:42.469,512] main: SIGNAL 10 , state not OK [00:08:42.469,573] main: count ZB_BDB_SIGNAL_STEERING 1 [00:08:42.469,573] zigbee_app_utils: Network steering was not successful (status: -1) [00:09:01.053,192] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:09:01.053,222] main: display_counters: Uart frames: Tx 0, Rx 0 [00:10:01.055,389] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:10:01.055,419] main: display_counters: Uart frames: Tx 0, Rx 0 [00:10:49.979,492] main: SIGNAL 10 , state not OK [00:10:49.979,522] main: count ZB_BDB_SIGNAL_STEERING 2 [00:10:49.979,553] zigbee_app_utils: Network steering was not successful (status: -1) [00:11:01.059,326] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:11:01.059,356] main: display_counters: Uart frames: Tx 0, Rx 0 [00:12:01.064,758] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:12:01.064,758] main: display_counters: Uart frames: Tx 0, Rx 0 [00:13:01.069,213] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:13:01.069,244] main: display_counters: Uart frames: Tx 0, Rx 0 [00:14:01.074,829] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:14:01.074,859] main: display_counters: Uart frames: Tx 0, Rx 0 [00:15:01.078,338] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:15:01.078,369] main: display_counters: Uart frames: Tx 0, Rx 0 [00:16:01.080,932] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:16:01.080,963] main: display_counters: Uart frames: Tx 0, Rx 0 [00:17:01.084,197] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:17:01.084,228] main: display_counters: Uart frames: Tx 0, Rx 0 uart:~$ [00:00:00.001,647] ieee802154_nrf5: nRF5 802154 radio initialized *** Booting nRF Connect SDK v2.5.1 *** [00:00:00.011,383] main: Router started successfully [00:00:00.011,383] main: RESET [00:00:00.011,413] main: get_reset_reason: Reset cause is: RESET_SOFTWARE [00:00:00.693,054] zigbee_shell: Register ZCL ctx at Zigbee device to use Zigbee shell ZCL commands. [00:00:00.693,084] main: SIGNAL 23 , state not OK [00:00:00.693,115] zigbee_app_utils: Production configuration is not present or invalid (status: -1) [00:00:00.693,481] main: SIGNAL 1 , state OK [00:00:00.693,511] zigbee_app_utils: Zigbee stack initialized [00:00:00.697,937] main: SIGNAL 5: Device started for the first time after the NVRAM erase [00:00:00.697,967] zigbee_app_utils: Device started for the first time [00:00:00.697,967] zigbee_app_utils: Start network steering [00:00:00.697,998] zigbee_app_utils: Started network rejoin procedure. [00:00:42.232,543] main: SIGNAL 10 , state not OK [00:00:42.232,574] main: count ZB_BDB_SIGNAL_STEERING 1 [00:00:42.232,574] zigbee_app_utils: Network steering was not successful (status: -1) [00:01:00.439,117] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:01:00.439,147] main: display_counters: Uart frames: Tx 0, Rx 0 [00:01:24.766,540] main: SIGNAL 10 , state not OK [00:01:24.766,571] main: count ZB_BDB_SIGNAL_STEERING 2 [00:01:24.766,571] zigbee_app_utils: Network steering was not successful (status: -1) [00:02:00.656,341] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:02:00.656,372] main: display_counters: Uart frames: Tx 0, Rx 0 [00:02:09.274,536] main: SIGNAL 10 , state not OK [00:02:09.274,566] main: count ZB_BDB_SIGNAL_STEERING 3 [00:02:09.274,566] main: parnet_node 0xffff [00:02:09.274,597] main: reset zb_bdb_reset_via_local_action 3 [00:02:09.274,627] zigbee_app_utils: Network steering was not successful (status: -1) [00:02:09.295,440] main: SIGNAL 3: The device has left the network [00:02:09.295,440] zigbee_app_utils: Network left (leave type: 0) [00:02:57.760,528] main: SIGNAL 10 , state not OK [00:02:57.760,559] main: count ZB_BDB_SIGNAL_STEERING 1 [00:02:57.760,589] zigbee_app_utils: Network steering was not successful (status: -1) [00:03:00.661,071] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:03:00.661,102] main: display_counters: Uart frames: Tx 0, Rx 0 [00:04:01.037,353] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:04:01.037,384] main: display_counters: Uart frames: Tx 0, Rx 0 [00:04:10.159,545] main: SIGNAL 10 , state not OK [00:04:10.159,576] main: count ZB_BDB_SIGNAL_STEERING 2 [00:04:10.159,606] zigbee_app_utils: Network steering was not successful (status: -1) [00:05:01.038,116] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:05:01.038,146] main: display_counters: Uart frames: Tx 0, Rx 0 [00:05:54.429,534] main: SIGNAL 10 , state not OK [00:05:54.429,565] main: count ZB_BDB_SIGNAL_STEERING 3 [00:05:54.429,595] main: parnet_node 0xffff [00:05:54.429,595] main: reset zb_bdb_reset_via_local_action 3 [00:05:54.429,626] zigbee_app_utils: Network steering was not successful (status: -1) [00:05:54.450,439] main: SIGNAL 3: The device has left the network [00:05:54.450,439] zigbee_app_utils: Network left (leave type: 0) [00:06:01.043,792] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:06:01.043,823] main: display_counters: Uart frames: Tx 0, Rx 0 [00:07:01.044,219] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:07:01.044,250] main: display_counters: Uart frames: Tx 0, Rx 0 [00:08:01.047,698] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:08:01.047,729] main: display_counters: Uart frames: Tx 0, Rx 0 [00:08:42.454,528] main: SIGNAL 10 , state not OK [00:08:42.454,559] main: count ZB_BDB_SIGNAL_STEERING 1 [00:08:42.454,589] zigbee_app_utils: Network steering was not successful (status: -1) [00:09:01.048,950] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:09:01.048,980] main: display_counters: Uart frames: Tx 0, Rx 0 [00:10:01.050,384] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:10:01.050,415] main: display_counters: Uart frames: Tx 0, Rx 0 [00:10:49.979,492] main: SIGNAL 10 , state not OK [00:10:49.979,522] main: count ZB_BDB_SIGNAL_STEERING 2 [00:10:49.979,553] zigbee_app_utils: Network steering was not successful (status: -1) [00:11:01.053,894] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:11:01.053,924] main: display_counters: Uart frames: Tx 0, Rx 0 [00:12:01.054,687] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:12:01.054,718] main: display_counters: Uart frames: Tx 0, Rx 0 [00:13:01.055,145] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:13:01.055,175] main: display_counters: Uart frames: Tx 0, Rx 0 [00:14:01.057,739] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:14:01.057,769] main: display_counters: Uart frames: Tx 0, Rx 0 [00:15:01.062,774] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:15:01.062,774] main: display_counters: Uart frames: Tx 0, Rx 0 [00:16:01.063,049] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:16:01.063,079] main: display_counters: Uart frames: Tx 0, Rx 0 [00:17:01.068,695] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:17:01.068,725] main: display_counters: Uart frames: Tx 0, Rx 0 uart:~$ [00:00:00.001,647] ieee802154_nrf5: nRF5 802154 radio initialized *** Booting nRF Connect SDK v2.5.1 *** [00:00:00.011,138] main: Router started successfully [00:00:00.011,169] main: RESET [00:00:00.011,169] main: get_reset_reason: Reset cause is: RESET_PIN [00:00:00.692,779] zigbee_shell: Register ZCL ctx at Zigbee device to use Zigbee shell ZCL commands. [00:00:00.692,810] main: SIGNAL 23 , state not OK [00:00:00.692,840] zigbee_app_utils: Production configuration is not present or invalid (status: -1) [00:00:00.693,206] main: SIGNAL 1 , state OK [00:00:00.693,237] zigbee_app_utils: Zigbee stack initialized [00:00:00.697,631] main: SIGNAL 5: Device started for the first time after the NVRAM erase [00:00:00.697,662] zigbee_app_utils: Device started for the first time [00:00:00.697,662] zigbee_app_utils: Start network steering [00:00:00.697,692] zigbee_app_utils: Started network rejoin procedure. [00:00:42.232,574] main: SIGNAL 10 , state not OK [00:00:42.232,604] main: Device is encountering issues during steering. [00:00:42.232,635] zigbee_app_utils: Network steering was not successful (status: -1) [00:01:00.439,178] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:01:00.439,208] main: display_counters: Uart frames: Tx 0, Rx 0 [00:01:24.766,540] main: SIGNAL 10 , state not OK [00:01:24.766,571] main: Device is encountering issues during steering. [00:01:24.766,601] zigbee_app_utils: Network steering was not successful (status: -1) [00:02:00.656,311] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:02:00.656,341] main: display_counters: Uart frames: Tx 0, Rx 0 [00:02:09.274,658] main: SIGNAL 10 , state not OK [00:02:09.274,719] main: Device is encountering issues during steering. [00:02:09.274,719] main: device has not joined a coordinator. [00:02:09.274,749] main: The device will perform the NLME leave and clean all Zigbee persistent data except the outgoing NWK frame counter and application datasets [00:02:09.274,749] zigbee_app_utils: Network steering was not successful (status: -1) [00:02:09.295,532] main: SIGNAL 3: The device has left the network [00:02:09.295,562] zigbee_app_utils: Network left (leave type: 0) [00:02:57.760,620] main: SIGNAL 10 , state not OK [00:02:57.760,650] main: Device is encountering issues during steering. [00:02:57.760,681] zigbee_app_utils: Network steering was not successful (status: -1) [00:03:00.661,376] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:03:00.661,407] main: display_counters: Uart frames: Tx 0, Rx 0 uart:~$ [00:00:00.000,396] ieee802154_nrf5: nRF5 802154 radio initialized *** Booting nRF Connect SDK v2.5.1 *** [00:00:00.009,307] main: Router started successfully [00:00:00.009,338] main: RESET [00:00:00.009,338] main: get_reset_reason: Reset cause is: RESET_PIN [00:00:00.690,673] main: SIGNAL 23 , state not OK [00:00:00.690,673] zigbee_app_utils: Production configuration is not present or invalid (status: -1) [00:00:00.691,040] main: SIGNAL 1 , state OK [00:00:00.691,070] zigbee_app_utils: Zigbee stack initialized [00:00:00.695,495] main: SIGNAL 5: Device started for the first time after the NVRAM erase [00:00:00.695,526] zigbee_app_utils: Device started for the first time [00:00:00.695,556] zigbee_app_utils: Start network steering [00:00:00.695,556] zigbee_app_utils: Started network rejoin procedure. [00:00:42.217,498] main: SIGNAL 10 , state not OK [00:00:42.217,529] main: Device is encountering issues during steering. [00:00:42.217,559] zigbee_app_utils: Network steering was not successful (status: -1) [00:01:00.409,118] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:01:00.409,149] main: display_counters: Uart frames: Tx 0, Rx 0 [00:01:24.736,541] main: SIGNAL 10 , state not OK [00:01:24.736,541] main: Device is encountering issues during steering. [00:01:24.736,572] zigbee_app_utils: Network steering was not successful (status: -1) [00:02:00.626,342] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:02:00.626,373] main: display_counters: Uart frames: Tx 0, Rx 0 [00:02:09.244,476] main: SIGNAL 10 , state not OK [00:02:09.244,506] main: Device is encountering issues during steering. [00:02:09.244,537] main: device has not joined a coordinator. [00:02:09.244,537] main: The device will perform the NLME leave and clean all Zigbee persistent data except the outgoing NWK frame counter and application datasets [00:02:09.244,567] zigbee_app_utils: Network steering was not successful (status: -1) [00:02:09.265,350] main: SIGNAL 3: The device has left the network [00:02:09.265,380] zigbee_app_utils: Network left (leave type: 0) [00:02:57.729,492] main: SIGNAL 10 , state not OK [00:02:57.729,522] main: Device is encountering issues during steering. [00:02:57.729,553] zigbee_app_utils: Network steering was not successful (status: -1) [00:03:00.631,683] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:03:00.631,713] main: display_counters: Uart frames: Tx 0, Rx 0 [00:04:01.006,317] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:04:01.006,347] main: display_counters: Uart frames: Tx 0, Rx 0 [00:04:10.129,486] main: SIGNAL 10 , state not OK [00:04:10.129,547] main: Device is encountering issues during steering. [00:04:10.129,547] zigbee_app_utils: Network steering was not successful (status: -1) [00:05:01.008,605] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:05:01.008,636] main: display_counters: Uart frames: Tx 0, Rx 0 [00:05:54.398,498] main: SIGNAL 10 , state not OK [00:05:54.398,529] main: Device is encountering issues during steering. [00:05:54.398,559] main: device has not joined a coordinator. [00:05:54.398,559] main: The device will perform the NLME leave and clean all Zigbee persistent data except the outgoing NWK frame counter and application datasets [00:05:54.398,590] zigbee_app_utils: Network steering was not successful (status: -1) [00:05:54.419,372] main: SIGNAL 3: The device has left the network [00:05:54.419,403] zigbee_app_utils: Network left (leave type: 0) [00:06:01.013,244] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:06:01.013,275] main: display_counters: Uart frames: Tx 0, Rx 0 [00:07:01.015,686] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:07:01.015,716] main: display_counters: Uart frames: Tx 0, Rx 0 [00:08:01.019,134] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:08:01.019,165] main: display_counters: Uart frames: Tx 0, Rx 0 [00:08:42.423,492] main: SIGNAL 10 , state not OK [00:08:42.423,522] main: Device is encountering issues during steering. [00:08:42.423,553] zigbee_app_utils: Network steering was not successful (status: -1) [00:09:01.022,125] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:09:01.022,155] main: display_counters: Uart frames: Tx 0, Rx 0 [00:10:01.023,864] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:10:01.023,895] main: display_counters: Uart frames: Tx 0, Rx 0 [00:10:49.948,486] main: SIGNAL 10 , state not OK [00:10:49.948,516] main: Device is encountering issues during steering. [00:10:49.948,547] zigbee_app_utils: Network steering was not successful (status: -1) [00:11:01.028,259] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:11:01.028,289] main: display_counters: Uart frames: Tx 0, Rx 0 [00:12:01.031,341] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:12:01.031,372] main: display_counters: Uart frames: Tx 0, Rx 0 [00:13:01.032,043] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:13:01.032,073] main: display_counters: Uart frames: Tx 0, Rx 0 [00:14:01.036,834] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:14:01.036,865] main: display_counters: Uart frames: Tx 0, Rx 0 [00:15:01.041,992] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:15:01.042,022] main: display_counters: Uart frames: Tx 0, Rx 0 [00:16:01.042,327] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:16:01.042,358] main: display_counters: Uart frames: Tx 0, Rx 0 [00:17:01.048,004] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:17:01.048,034] main: display_counters: Uart frames: Tx 0, Rx 0 [00:00:00.000,427] ieee802154_nrf5: nRF5 802154 radio initialized *** Booting nRF Connect SDK v2.5.1 *** [00:00:00.009,307] main: Router started successfully [00:00:00.009,338] main: RESET [00:00:00.009,338] main: get_reset_reason: Reset cause is: RESET_SOFTWARE [00:00:00.690,643] main: SIGNAL 23 , state not OK [00:00:00.690,643] zigbee_app_utils: Production configuration is not present or invalid (status: -1) [00:00:00.691,009] main: SIGNAL 1 , state OK [00:00:00.691,040] zigbee_app_utils: Zigbee stack initialized [00:00:00.695,495] main: SIGNAL 5: Device started for the first time after the NVRAM erase [00:00:00.695,495] zigbee_app_utils: Device started for the first time [00:00:00.695,526] zigbee_app_utils: Start network steering [00:00:00.695,526] zigbee_app_utils: Started network rejoin procedure. [00:00:42.217,498] main: SIGNAL 10 , state not OK [00:00:42.217,529] main: Device is encountering issues during steering. [00:00:42.217,559] zigbee_app_utils: Network steering was not successful (status: -1) [00:01:00.409,118] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:01:00.409,149] main: display_counters: Uart frames: Tx 0, Rx 0 [00:01:24.736,511] main: SIGNAL 10 , state not OK [00:01:24.736,541] main: Device is encountering issues during steering. [00:01:24.736,572] zigbee_app_utils: Network steering was not successful (status: -1) [00:02:00.626,312] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:02:00.626,342] main: display_counters: Uart frames: Tx 0, Rx 0 [00:02:09.244,476] main: SIGNAL 10 , state not OK [00:02:09.244,506] main: Device is encountering issues during steering. [00:02:09.244,537] main: device has not joined a coordinator. [00:02:09.244,537] main: The device will perform the NLME leave and clean all Zigbee persistent data except the outgoing NWK frame counter and application datasets [00:02:09.244,567] zigbee_app_utils: Network steering was not successful (status: -1) [00:02:09.265,350] main: SIGNAL 3: The device has left the network [00:02:09.265,380] zigbee_app_utils: Network left (leave type: 0) [00:02:57.729,522] main: SIGNAL 10 , state not OK [00:02:57.729,553] main: Device is encountering issues during steering. [00:02:57.729,583] zigbee_app_utils: Network steering was not successful (status: -1) [00:03:00.631,225] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:03:00.631,256] main: display_counters: Uart frames: Tx 0, Rx 0 [00:04:01.006,317] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:04:01.006,347] main: display_counters: Uart frames: Tx 0, Rx 0 [00:04:10.129,486] main: SIGNAL 10 , state not OK [00:04:10.129,516] main: Device is encountering issues during steering. [00:04:10.129,547] zigbee_app_utils: Network steering was not successful (status: -1) [00:05:01.010,864] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:05:01.010,894] main: display_counters: Uart frames: Tx 0, Rx 0 [00:05:54.398,529] main: SIGNAL 10 , state not OK [00:05:54.398,559] main: Device is encountering issues during steering. [00:05:54.398,559] main: device has not joined a coordinator. [00:05:54.398,590] main: The device will perform the NLME leave and clean all Zigbee persistent data except the outgoing NWK frame counter and application datasets [00:05:54.398,620] zigbee_app_utils: Network steering was not successful (status: -1) [00:05:54.419,403] main: SIGNAL 3: The device has left the network [00:05:54.419,433] zigbee_app_utils: Network left (leave type: 0) [00:06:01.012,115] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:06:01.012,145] main: display_counters: Uart frames: Tx 0, Rx 0 [00:07:01.017,578] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:07:01.017,608] main: display_counters: Uart frames: Tx 0, Rx 0 [00:08:01.020,874] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:08:01.020,904] main: display_counters: Uart frames: Tx 0, Rx 0 [00:08:42.423,492] main: SIGNAL 10 , state not OK [00:08:42.423,522] main: Device is encountering issues during steering. [00:08:42.423,553] zigbee_app_utils: Network steering was not successful (status: -1) [00:09:01.023,864] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:09:01.023,895] main: display_counters: Uart frames: Tx 0, Rx 0 [00:10:01.027,252] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:10:01.027,282] main: display_counters: Uart frames: Tx 0, Rx 0 [00:10:49.948,486] main: SIGNAL 10 , state not OK [00:10:49.948,516] main: Device is encountering issues during steering. [00:10:49.948,516] zigbee_app_utils: Network steering was not successful (status: -1) [00:00:00.000,457] ieee802154_nrf5: nRF5 802154 radio initialized *** Booting nRF Connect SDK v2.5.1 *** [00:00:00.009,704] main: Router started successfully [00:00:00.009,704] main: RESET [00:00:00.009,704] main: get_reset_reason: Reset cause is: RESET_PIN [00:00:00.691,009] main: SIGNAL 23 , state not OK [00:00:00.691,009] zigbee_app_utils: Production configuration is not present or invalid (status: -1) [00:00:00.691,375] main: SIGNAL 1 , state OK [00:00:00.691,406] zigbee_app_utils: Zigbee stack initialized [00:00:00.695,800] main: SIGNAL 5: Device started for the first time after the NVRAM erase [00:00:00.695,800] zigbee_app_utils: Device started for the first time [00:00:00.695,831] zigbee_app_utils: Start network steering [00:00:00.695,831] zigbee_app_utils: Started network rejoin procedure. [00:00:42.217,590] main: SIGNAL 10 , state not OK [00:00:42.217,620] main: Device is encountering issues during steering. [00:00:42.217,620] zigbee_app_utils: Network steering was not successful (status: -1) [00:01:00.409,210] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:01:00.409,240] main: display_counters: Uart frames: Tx 0, Rx 0 [00:01:24.736,602] main: SIGNAL 10 , state not OK [00:01:24.736,633] main: Device is encountering issues during steering. [00:01:24.736,663] zigbee_app_utils: Network steering was not successful (status: -1) [00:02:00.626,342] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:02:00.626,373] main: display_counters: Uart frames: Tx 0, Rx 0 [00:02:09.244,628] main: SIGNAL 10 , state not OK [00:02:09.244,659] main: Device is encountering issues during steering. [00:02:09.244,659] main: device has not joined a coordinator. [00:02:09.244,689] main: The device will perform the NLME leave and clean all Zigbee persistent data except the outgoing NWK frame counter and application datasets [00:02:09.244,689] zigbee_app_utils: Network steering was not successful (status: -1) [00:02:09.265,502] main: SIGNAL 3: The device has left the network [00:02:09.265,533] zigbee_app_utils: Network left (leave type: 0) [00:02:57.729,614] main: SIGNAL 10 , state not OK [00:02:57.729,644] main: Device is encountering issues during steering. [00:02:57.729,675] zigbee_app_utils: Network steering was not successful (status: -1) [00:03:00.627,166] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:03:00.627,197] main: display_counters: Uart frames: Tx 0, Rx 0 [00:04:01.006,317] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:04:01.006,347] main: display_counters: Uart frames: Tx 0, Rx 0 [00:04:10.129,577] main: SIGNAL 10 , state not OK [00:04:10.129,608] main: Device is encountering issues during steering. [00:04:10.129,638] zigbee_app_utils: Network steering was not successful (status: -1) [00:05:01.008,636] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:05:01.008,666] main: display_counters: Uart frames: Tx 0, Rx 0 [00:05:22.067,810] main: SIGNAL 10 , state not OK [00:05:22.067,810] main: Device is encountering issues during steering. [00:05:22.067,840] main: device has not joined a coordinator. [00:05:22.067,871] main: The device will perform the NLME leave and clean all Zigbee persistent data except the outgoing NWK frame counter and application datasets [00:05:22.067,871] zigbee_app_utils: Network steering was not successful (status: -1) [00:05:22.088,714] main: SIGNAL 3: The device has left the network [00:05:22.088,745] zigbee_app_utils: Network left (leave type: 0) [00:00:00.001,647] ieee802154_nrf5: nRF5 802154 radio initialized *** Booting nRF Connect SDK v2.5.1 *** [00:00:00.011,199] main: Router started successfully [00:00:00.011,230] main: RESET [00:00:00.011,230] main: get_reset_reason: Reset cause is: RESET_PIN [00:00:00.692,871] zigbee_shell: Register ZCL ctx at Zigbee device to use Zigbee shell ZCL commands. [00:00:00.692,901] main: SIGNAL 23 , state not OK [00:00:00.692,932] zigbee_app_utils: Production configuration is not present or invalid (status: -1) [00:00:00.693,298] main: SIGNAL 1 , state OK [00:00:00.693,298] zigbee_app_utils: Zigbee stack initialized [00:00:00.697,692] main: SIGNAL 5: Device started for the first time after the NVRAM erase [00:00:00.697,692] zigbee_app_utils: Device started for the first time [00:00:00.697,723] zigbee_app_utils: Start network steering [00:00:00.697,723] zigbee_app_utils: Started network rejoin procedure. [00:00:10.316,680] main: diagnostic_zigbee_info: Zigbee application joined the network: bellow some info: [00:00:10.316,711] main: diagnostic_zigbee_info: MAC address: f4 ce 36 1f cc b3 46 a2 |..6...F. [00:00:10.316,741] main: diagnostic_zigbee_info: zigbee shrot addr: 0xe545 [00:00:10.316,772] main: diagnostic_zigbee_info: Extended PAN ID: 00 00 00 00 00 00 99 99 |........ [00:00:10.316,772] main: diagnostic_zigbee_info: zigbee role router [00:00:10.316,802] main: diagnostic_zigbee_info: zigbee channel: 19 [00:00:10.455,993] main: SIGNAL 54 , state OK [00:00:10.456,024] zigbee_app_utils: Unimplemented signal (signal: 54, status: 0) [00:00:10.526,367] main: SIGNAL 54 , state OK [00:00:10.526,397] zigbee_app_utils: Unimplemented signal (signal: 54, status: 0) [00:00:10.528,198] main: SIGNAL 10 , state OK [00:00:10.528,198] main: Device is encountering issues during steering. [00:00:10.528,411] zigbee_app_utils: Joined network successfully (Extended PAN ID: 0000000000009999, PAN ID: 0x17ba) [00:00:10.528,411] zigbee_app_utils: Network rejoin procedure stopped. [00:00:10.536,376] main: data_indication_cb: Rx APS Frame with profile 0xc105, cluster 0x12, src_ep 219, dest_ep 232, payload 2 bytes [00:00:33.877,960] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:00:48.843,292] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:01:00.003,265] main: display_counters: APS RX COUNTERS: Total 3, Binary 0, Commis 0 [00:01:00.003,295] main: display_counters: Uart frames: Tx 0, Rx 0 [00:01:03.766,296] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:01:18.767,425] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:01:25.251,770] main: SIGNAL 24 , state OK [00:01:25.251,770] main: Device is encountering issues during steering. [00:01:25.251,800] zigbee_app_utils: Parent is unreachable [00:01:33.751,922] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:01:40.223,571] main: SIGNAL 24 , state OK [00:01:40.223,602] main: Device is encountering issues during steering. [00:01:40.223,602] main: Device has joined a coordinator, but there might be an issue. Parent Node: 0x25fc [00:01:40.223,632] main: The device will perform the NLME leave and clean all Zigbee persistent data except the outgoing NWK frame counter and application datasets [00:01:40.223,632] zigbee_app_utils: Parent is unreachable [00:01:40.890,808] main: SIGNAL 3: The device has left the network [00:01:40.890,808] zigbee_app_utils: Network left (leave type: 0) [00:01:40.890,838] zigbee_app_utils: Started network rejoin procedure. [00:01:50.088,287] main: SIGNAL 10 , state not OK [00:01:50.088,317] main: Device is encountering issues during steering. [00:01:50.088,348] zigbee_app_utils: Network steering was not successful (status: -1) [00:02:00.170,806] main: display_counters: APS RX COUNTERS: Total 6, Binary 0, Commis 0 [00:02:00.170,837] main: display_counters: Uart frames: Tx 0, Rx 0 [00:02:00.914,611] main: data_indication_cb: Rx APS Frame with profile 0xc105, cluster 0x12, src_ep 219, dest_ep 232, payload 2 bytes [00:02:01.234,649] main: SIGNAL 54 , state OK [00:02:01.234,680] zigbee_app_utils: Unimplemented signal (signal: 54, status: 0) [00:02:01.687,713] main: SIGNAL 54 , state OK [00:02:01.687,744] zigbee_app_utils: Unimplemented signal (signal: 54, status: 0) [00:02:01.689,544] main: SIGNAL 10 , state OK [00:02:01.689,575] main: Device is encountering issues during steering. [00:02:01.689,758] zigbee_app_utils: Joined network successfully (Extended PAN ID: 0000000000009999, PAN ID: 0x17ba) [00:02:01.689,758] zigbee_app_utils: Network rejoin procedure stopped. [00:02:03.752,136] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:02:18.673,431] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:02:19.233,001] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:02:19.446,350] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:02:19.791,320] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:02:20.099,670] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:02:21.113,311] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:02:31.495,849] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:02:32.004,058] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:02:32.095,153] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:02:32.695,068] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:02:32.841,766] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes ua[00:02:46.516,357] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:02:47.683,746] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:02:47.777,770] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:02:48.000,976] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:02:48.259,216] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:02:48.933,807] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:03:00.174,468] main: display_counters: APS RX COUNTERS: Total 25, Binary 0, Commis 0 [00:03:00.174,499] main: display_counters: Uart frames: Tx 0, Rx 0 [00:03:01.195,953] main: SIGNAL 24 , state OK [00:03:01.195,983] main: Device is encountering issues during steering. [00:03:01.195,983] main: Device has joined a coordinator, but there might be an issue. Parent Node: 0x7249 [00:03:01.196,014] main: The device will perform the NLME leave and clean all Zigbee persistent data except the outgoing NWK frame counter and application datasets [00:03:01.196,014] zigbee_app_utils: Parent is unreachable [00:03:01.415,252] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:03:02.201,293] main: SIGNAL 3: The device has left the network [00:03:02.201,324] zigbee_app_utils: Network left (leave type: 0) [00:03:02.201,324] zigbee_app_utils: Started network rejoin procedure. [00:03:43.721,588] main: SIGNAL 10 , state not OK [00:03:43.721,618] main: Device is encountering issues during steering. [00:03:43.721,618] zigbee_app_utils: Network steering was not successful (status: -1) [00:04:00.394,317] main: display_counters: APS RX COUNTERS: Total 26, Binary 0, Commis 0 [00:04:00.394,378] main: display_counters: Uart frames: Tx 0, Rx 0 [00:04:26.240,539] main: SIGNAL 10 , state not OK [00:04:26.240,539] main: Device is encountering issues during steering. [00:04:26.240,570] zigbee_app_utils: Network steering was not successful (status: -1) [00:05:00.615,356] main: display_counters: APS RX COUNTERS: Total 26, Binary 0, Commis 0 [00:05:00.615,386] main: display_counters: Uart frames: Tx 0, Rx 0 uart:~$ [00:00:00.001,678] ieee802154_nrf5: nRF5 802154 radio initialized *** Booting nRF Connect SDK v2.5.1 *** [00:00:00.011,230] main: Router started successfully [00:00:00.011,230] main: RESET [00:00:00.011,260] main: get_reset_reason: Reset cause is: RESET_SOFTWARE [00:00:00.692,871] zigbee_shell: Register ZCL ctx at Zigbee device to use Zigbee shell ZCL commands. [00:00:00.692,901] main: SIGNAL 23 , state not OK [00:00:00.692,932] zigbee_app_utils: Production configuration is not present or invalid (status: -1) [00:00:00.693,298] main: SIGNAL 1 , state OK [00:00:00.693,298] zigbee_app_utils: Zigbee stack initialized [00:00:00.697,692] main: SIGNAL 5: Device started for the first time after the NVRAM erase [00:00:00.697,723] zigbee_app_utils: Device started for the first time [00:00:00.697,723] zigbee_app_utils: Start network steering [00:00:00.697,753] zigbee_app_utils: Started network rejoin procedure. [00:00:42.232,849] main: SIGNAL 10 , state not OK [00:00:42.232,879] main: Device is encountering issues during steering. [00:00:42.232,879] zigbee_app_utils: Network steering was not successful (status: -1) [00:01:00.439,208] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:01:00.439,239] main: display_counters: Uart frames: Tx 0, Rx 0 [00:01:24.766,510] main: SIGNAL 10 , state not OK [00:01:24.766,540] main: Device is encountering issues during steering. [00:01:24.766,571] zigbee_app_utils: Network steering was not successful (status: -1) [00:02:00.656,311] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:02:00.656,372] main: display_counters: Uart frames: Tx 0, Rx 0 [00:02:09.274,688] main: SIGNAL 10 , state not OK [00:02:09.274,719] main: Device is encountering issues during steering. [00:02:09.274,749] main: device has not joined a coordinator. [00:02:09.274,749] main: The device will perform the NLME leave and clean all Zigbee persistent data except the outgoing NWK frame counter and application datasets [00:02:09.274,780] zigbee_app_utils: Network steering was not successful (status: -1) [00:02:09.295,532] main: SIGNAL 3: The device has left the network [00:02:09.295,562] zigbee_app_utils: Network left (leave type: 0) [00:02:57.760,528] main: SIGNAL 10 , state not OK [00:02:57.760,559] main: Device is encountering issues during steering. [00:02:57.760,559] zigbee_app_utils: Network steering was not successful (status: -1) [00:03:00.661,285] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:03:00.661,315] main: display_counters: Uart frames: Tx 0, Rx 0 [00:04:01.037,322] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:04:01.037,353] main: display_counters: Uart frames: Tx 0, Rx 0 [00:04:02.542,266] main: diagnostic_zigbee_info: Zigbee application joined the network: bellow some info: [00:04:02.542,297] main: diagnostic_zigbee_info: MAC address: f4 ce 36 1f cc b3 46 a2 |..6...F. [00:04:02.542,327] main: diagnostic_zigbee_info: zigbee shrot addr: 0xc585 [00:04:02.542,358] main: diagnostic_zigbee_info: Extended PAN ID: 00 00 00 00 00 00 99 99 |........ [00:04:02.542,358] main: diagnostic_zigbee_info: zigbee role router [00:04:02.542,388] main: diagnostic_zigbee_info: zigbee channel: 19 [00:04:03.072,479] main: SIGNAL 54 , state OK [00:04:03.072,509] zigbee_app_utils: Unimplemented signal (signal: 54, status: 0) [00:04:03.194,854] main: data_indication_cb: Rx APS Frame with profile 0xc105, cluster 0x12, src_ep 219, dest_ep 232, payload 2 bytes [00:04:03.547,058] main: SIGNAL 54 , state OK [00:04:03.547,058] zigbee_app_utils: Unimplemented signal (signal: 54, status: 0) [00:04:03.548,889] main: SIGNAL 10 , state OK [00:04:03.548,889] main: Device is encountering issues during steering. [00:04:03.549,102] zigbee_app_utils: Joined network successfully (Extended PAN ID: 0000000000009999, PAN ID: 0x17ba) [00:04:03.549,102] zigbee_app_utils: Network rejoin procedure stopped. [00:04:07.119,232] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:04:22.053,100] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:04:37.030,639] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:04:52.444,305] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:05:01.042,846] main: display_counters: APS RX COUNTERS: Total 5, Binary 0, Commis 0 [00:05:01.042,877] main: display_counters: Uart frames: Tx 0, Rx 0 [00:05:02.918,731] main: SIGNAL 24 , state OK [00:05:02.918,731] main: Device is encountering issues during steering. [00:05:02.918,762] main: Device has joined a coordinator, but there might be an issue. Parent Node: 0xe257 [00:05:02.918,792] main: The device will perform the NLME leave and clean all Zigbee persistent data except the outgoing NWK frame counter and application datasets [00:05:02.918,792] zigbee_app_utils: Parent is unreachable [00:05:03.540,802] main: SIGNAL 3: The device has left the network [00:05:03.540,802] zigbee_app_utils: Network left (leave type: 0) [00:05:03.540,832] zigbee_app_utils: Started network rejoin procedure. [00:05:13.652,465] main: SIGNAL 54 , state OK [00:05:13.652,496] zigbee_app_utils: Unimplemented signal (signal: 54, status: 0) [00:05:14.121,856] main: SIGNAL 54 , state OK [00:05:14.121,856] zigbee_app_utils: Unimplemented signal (signal: 54, status: 0) [00:05:14.123,657] main: SIGNAL 10 , state OK [00:05:14.123,657] main: Device is encountering issues during steering. [00:05:14.123,840] zigbee_app_utils: Joined network successfully (Extended PAN ID: 0000000000009999, PAN ID: 0x17ba) [00:05:14.123,870] zigbee_app_utils: Network rejoin procedure stopped. [00:05:22.013,153] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:05:37.023,223] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:05:38.088,256] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:05:38.190,185] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:05:38.307,556] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:05:38.528,411] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:05:38.612,396] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:05:51.926,971] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:05:52.152,709] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:05:52.304,870] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:05:52.489,501] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:05:52.735,809] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:05:52.891,113] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:06:01.044,067] main: display_counters: APS RX COUNTERS: Total 18, Binary 0, Commis 0 [00:06:01.044,097] main: display_counters: Uart frames: Tx 0, Rx 0 [00:06:13.564,941] main: SIGNAL 24 , state OK [00:06:13.564,971] main: Device is encountering issues during steering. [00:06:13.565,002] zigbee_app_utils: Parent is unreachable [00:06:13.854,705] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:06:14.106,414] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:06:14.451,812] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:06:14.654,541] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:06:14.803,955] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:06:15.304,382] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes uart:~$ [00:00:00.001,647] ieee802154_nrf5: nRF5 802154 radio initialized *** Booting nRF Connect SDK v2.5.1 *** [00:00:00.011,199] main: Router started successfully [00:00:00.011,199] main: RESET [00:00:00.011,230] main: get_reset_reason: Reset cause is: RESET_SOFTWARE [00:00:00.692,871] zigbee_shell: Register ZCL ctx at Zigbee device to use Zigbee shell ZCL commands. [00:00:00.692,901] main: SIGNAL 23 , state not OK [00:00:00.692,932] zigbee_app_utils: Production configuration is not present or invalid (status: -1) [00:00:00.693,298] main: SIGNAL 1 , state OK [00:00:00.693,298] zigbee_app_utils: Zigbee stack initialized [00:00:00.697,692] main: SIGNAL 5: Device started for the first time after the NVRAM erase [00:00:00.697,723] zigbee_app_utils: Device started for the first time [00:00:00.697,723] zigbee_app_utils: Start network steering [00:00:00.697,753] zigbee_app_utils: Started network rejoin procedure. [00:00:09.904,327] main: SIGNAL 10 , state not OK [00:00:09.904,357] main: Device is encountering issues during steering. [00:00:09.904,388] zigbee_app_utils: Network steering was not successful (status: -1) [00:00:20.525,726] main: diagnostic_zigbee_info: Zigbee application joined the network: bellow some info: [00:00:20.525,756] main: diagnostic_zigbee_info: MAC address: f4 ce 36 1f cc b3 46 a2 |..6...F. [00:00:20.525,787] main: diagnostic_zigbee_info: zigbee shrot addr: 0xc300 [00:00:20.525,817] main: diagnostic_zigbee_info: Extended PAN ID: 00 00 00 00 00 00 99 99 |........ [00:00:20.525,817] main: diagnostic_zigbee_info: zigbee role router [00:00:20.525,848] main: diagnostic_zigbee_info: zigbee channel: 19 [00:00:21.051,422] main: SIGNAL 54 , state OK [00:00:21.051,452] zigbee_app_utils: Unimplemented signal (signal: 54, status: 0) [00:00:21.505,432] main: SIGNAL 54 , state OK [00:00:21.505,462] zigbee_app_utils: Unimplemented signal (signal: 54, status: 0) [00:00:21.507,324] main: SIGNAL 10 , state OK [00:00:21.507,324] main: Device is encountering issues during steering. [00:00:21.507,507] zigbee_app_utils: Joined network successfully (Extended PAN ID: 0000000000009999, PAN ID: 0x17ba) [00:00:21.507,537] zigbee_app_utils: Network rejoin procedure stopped. [00:00:23.383,331] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:00:37.875,854] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:00:52.847,351] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:01:00.004,852] main: display_counters: APS RX COUNTERS: Total 3, Binary 0, Commis 0 [00:01:00.004,882] main: display_counters: Uart frames: Tx 0, Rx 0 uart:~$ nbr monitor on uart:~$ nbr monitor on Done [00:01:07.567,260] zigbee_shell_nbr: Active neighbor table (5 entries): [00:01:07.567,291] zigbee_shell_nbr: [idx] ext_addr device_type relationship cost age timeout [00:01:07.567,474] zigbee_shell_nbr: [ 0] ffffffffffffffff unknown unknown 7 3 -1 [00:01:07.567,687] zigbee_shell_nbr: [ 1] ffffffffffffffff router unknown 7 3 -1 [00:01:07.567,871] zigbee_shell_nbr: [ 2] f4ce3645861c5597 router parent 6 3 -1 [00:01:07.568,054] zigbee_shell_nbr: [ 3] ffffffffffffffff unknown unknown 7 2 -1 [00:01:07.568,237] zigbee_shell_nbr: [ 4] ffffffffffffffff unknown unknown 7 1 -1 [00:01:07.831,237] main: data_indication_cb: Rx APS Frame with profile 0x0, cluster 0x13, src_ep 0, dest_ep 0, payload 12 bytes [00:01:08.576,354] zigbee_shell_nbr: Active neighbor table (6 entries): [00:01:08.576,354] zigbee_shell_nbr: [idx] ext_addr device_type relationship cost age timeout [00:01:08.576,568] zigbee_shell_nbr: [ 0] ffffffffffffffff unknown unknown 7 3 -1 [00:01:08.576,751] zigbee_shell_nbr: [ 1] ffffffffffffffff router unknown 7 3 -1 [00:01:08.576,965] zigbee_shell_nbr: [ 2] f4ce3645861c5597 router parent 6 3 -1 [00:01:08.577,148] zigbee_shell_nbr: [ 3] ffffffffffffffff unknown unknown 7 2 -1 [00:01:08.577,331] zigbee_shell_nbr: [ 4] ffffffffffffffff unknown unknown 7 1 -1 [00:01:08.577,545] zigbee_shell_nbr: [ 5] ffffffffffffffff unknown unknown 7 0 -1 [00:01:20.908,721] main: SIGNAL 24 , state OK [00:01:20.908,721] main: Device is encountering issues during steering. [00:01:20.908,752] main: Device has joined a coordinator, but there might be an issue. Parent Node: 0xfc02 [00:01:20.908,752] main: The device will perform the NLME leave and clean all Zigbee persistent data except the outgoing NWK frame counter and application datasets [00:01:20.908,782] zigbee_app_utils: Parent is unreachable [00:01:21.551,849] main: SIGNAL 3: The device has left the network [00:01:21.551,849] zigbee_app_utils: Network left (leave type: 0) [00:01:21.551,879] zigbee_app_utils: Started network rejoin procedure. [00:01:21.702,270] zigbee_shell_nbr: Active neighbor table (0 entries): [00:01:21.702,301] zigbee_shell_nbr: [idx] ext_addr device_type relationship cost age timeout [00:01:30.791,259] zigbee_shell_nbr: Active neighbor table (0 entries): [00:01:30.791,290] zigbee_shell_nbr: [idx] ext_addr device_type relationship cost age timeout [00:02:00.044,311] main: display_counters: APS RX COUNTERS: Total 4, Binary 0, Commis 0 [00:02:00.044,342] main: display_counters: Uart frames: Tx 0, Rx 0 [00:02:03.078,918] main: SIGNAL 10 , state not OK [00:02:03.078,918] main: Device is encountering issues during steering. [00:02:03.078,948] zigbee_app_utils: Network steering was not successful (status: -1) [00:02:45.596,710] main: SIGNAL 10 , state not OK [00:02:45.596,740] main: Device is encountering issues during steering. [00:02:45.596,771] zigbee_app_utils: Network steering was not successful (status: -1) [00:03:00.219,451] main: display_counters: APS RX COUNTERS: Total 4, Binary 0, Commis 0 [00:03:00.219,482] main: display_counters: Uart frames: Tx 0, Rx 0 [00:03:30.104,705] main: SIGNAL 10 , state not OK [00:03:30.104,736] main: Device is encountering issues during steering. [00:03:30.104,736] main: device has not joined a coordinator. [00:03:30.104,766] main: The device will perform the NLME leave and clean all Zigbee persistent data except the outgoing NWK frame counter and application datasets [00:03:30.104,797] zigbee_app_utils: Network steering was not successful (status: -1) [00:03:30.125,549] main: SIGNAL 3: The device has left the network [00:03:30.125,579] zigbee_app_utils: Network left (leave type: 0) [00:03:30.957,275] zigbee_shell_nbr: Active neighbor table (0 entries): [00:03:30.957,275] zigbee_shell_nbr: [idx] ext_addr device_type relationship cost age timeout [00:03:47.114,227] zigbee_shell_nbr: Active neighbor table (0 entries): [00:03:47.114,257] zigbee_shell_nbr: [idx] ext_addr device_type relationship cost age timeout [00:04:00.348,327] main: display_counters: APS RX COUNTERS: Total 4, Binary 0, Commis 0 [00:04:00.348,358] main: display_counters: Uart frames: Tx 0, Rx 0 [00:04:18.590,545] main: SIGNAL 10 , state not OK [00:04:18.590,576] main: Device is encountering issues during steering. [00:04:18.590,606] zigbee_app_utils: Network steering was not successful (status: -1) [00:05:00.600,341] main: display_counters: APS RX COUNTERS: Total 4, Binary 0, Commis 0 [00:05:00.600,372] main: display_counters: Uart frames: Tx 0, Rx 0 [00:05:30.989,929] main: SIGNAL 10 , state not OK [00:05:30.989,959] main: Device is encountering issues during steering. [00:05:30.989,959] zigbee_app_utils: Network steering was not successful (status: -1) [00:06:00.605,041] main: display_counters: APS RX COUNTERS: Total 4, Binary 0, Commis 0 [00:06:00.605,072] main: display_counters: Uart frames: Tx 0, Rx 0 [00:07:01.087,280] main: display_counters: APS RX COUNTERS: Total 4, Binary 0, Commis 0 [00:07:01.087,310] main: display_counters: Uart frames: Tx 0, Rx 0 uart:~$ [00:00:00.001,647] ieee802154_nrf5: nRF5 802154 radio initialized *** Booting nRF Connect SDK v2.5.1 *** [00:00:00.011,199] main: Router started successfully [00:00:00.011,230] main: RESET [00:00:00.011,230] main: get_reset_reason: Reset cause is: RESET_SOFTWARE [00:00:00.692,901] zigbee_shell: Register ZCL ctx at Zigbee device to use Zigbee shell ZCL commands. [00:00:00.692,932] main: SIGNAL 23 , state not OK [00:00:00.692,962] zigbee_app_utils: Production configuration is not present or invalid (status: -1) [00:00:00.693,328] main: SIGNAL 1 , state OK [00:00:00.693,328] zigbee_app_utils: Zigbee stack initialized [00:00:00.697,723] main: SIGNAL 5: Device started for the first time after the NVRAM erase [00:00:00.697,753] zigbee_app_utils: Device started for the first time [00:00:00.697,753] zigbee_app_utils: Start network steering [00:00:00.697,753] zigbee_app_utils: Started network rejoin procedure. [00:00:42.232,513] main: SIGNAL 10 , state not OK [00:00:42.232,543] main: Device is encountering issues during steering. [00:00:42.232,574] zigbee_app_utils: Network steering was not successful (status: -1) [00:01:00.439,514] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:01:00.439,544] main: display_counters: Uart frames: Tx 0, Rx 0 [00:01:24.766,723] main: SIGNAL 10 , state not OK [00:01:24.766,754] main: Device is encountering issues during steering. [00:01:24.766,784] zigbee_app_utils: Network steering was not successful (status: -1) [00:02:00.656,341] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:02:00.656,372] main: display_counters: Uart frames: Tx 0, Rx 0 [00:02:09.274,688] main: SIGNAL 10 , state not OK [00:02:09.274,719] main: Device is encountering issues during steering. [00:02:09.274,719] main: device has not joined a coordinator. [00:02:09.274,749] main: The device will perform the NLME leave and clean all Zigbee persistent data except the outgoing NWK frame counter and application datasets [00:02:09.274,780] zigbee_app_utils: Network steering was not successful (status: -1) [00:02:09.295,532] main: SIGNAL 3: The device has left the network [00:02:09.295,562] zigbee_app_utils: Network left (leave type: 0) [00:02:57.760,620] main: SIGNAL 10 , state not OK [00:02:57.760,650] main: Device is encountering issues during steering. [00:02:57.760,681] zigbee_app_utils: Network steering was not successful (status: -1) [00:03:00.661,376] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:03:00.661,407] main: display_counters: Uart frames: Tx 0, Rx 0 [00:04:01.037,322] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:04:01.037,353] main: display_counters: Uart frames: Tx 0, Rx 0 [00:04:10.159,729] main: SIGNAL 10 , state not OK [00:04:10.159,759] main: Device is encountering issues during steering. [00:04:10.159,759] zigbee_app_utils: Network steering was not successful (status: -1) [00:05:01.039,764] main: display_counters: APS RX COUNTERS: Total 0, Binary 0, Commis 0 [00:05:01.039,794] main: display_counters: Uart frames: Tx 0, Rx 0 uart:~$