#The following 3 lines define the clock used by the RAYTAC maodule disable for UBLOX Nina B3
CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC=y
CONFIG_CLOCK_CONTROL_NRF_K32SRC_XTAL=n
CONFIG_CLOCK_CONTROL_NRF_K32SRC_250PPM=y

#CONFIG_SET_REGOUT0=y 

CONFIG_BT_CTLR_ADV_DATA_LEN_MAX=128
#CONFIG_OZARK_ENCRYPTION=y

#Don't show colour on log display using RTT
CONFIG_LOG_BACKEND_SHOW_COLOR=n
CONFIG_BT_DEBUG_LOG=y

CONFIG_ADC=y
CONFIG_SYS_POWER_MANAGEMENT=y
CONFIG_PM_DEVICE=y
#CONFIG_PM_DEVICE_IDLE=y
CONFIG_PM=y
# Devzone Thought
CONFIG_GPIO_NRF_INT_EDGE_USING_SENSE=y
CONFIG_DEVICE_POWER_MANAGEMENT=y

#Allow Dynamic control of I2C during run time
CONFIG_DYNAMIC_I2C=y

CONFIG_OZARK_VERBOSE=y

CONFIG_BT_DEVICE_NAME="FYNDA"
CONFIG_BT=y
CONFIG_BT_BROADCASTER=y
CONFIG_BT_OBSERVER=y

CONFIG_TX_CYCLE_DELAY=1200
CONFIG_LOST_FLUX_CAPACITOR_DELAY=60

#CONFIG_BT_BROADCASTER=y
#CONFIG_BT_OBSERVER=y

CONFIG_STANDARD_PHY=y
CONFIG_I2C=y
#CONFIG_SERIAL=n
CONFIG_DEBUG_OPTIMIZATIONS=y

#Following is Gateway/Relay Node and is used to drive external LED
CONFIG_RELAY_NODE=y
CONFIG_SENSOR=y
CONFIG_SI7055=n
CONFIG_SI7055_ENABLE_CHECKSUM=n
CONFIG_LIS2DH=n
CONFIG_AS6200=n
CONFIG_AS6212=n
CONFIG_AS6212X=n

CONFIG_BUZZER_AVAILABLE=n
CONFIG_OZARK_LEDS_ENABLED=y

#Additions
CONFIG_GPIO=y
CONFIG_BT_CTLR_PHY_CODED=y
CONFIG_BT_EXT_ADV=y
#CONFIG_BT_LL_SOFTDEVICE_DEFAULT=y
CONFIG_BT_USER_PHY_UPDATE=y
CONFIG_RTT_CONSOLE=y
CONFIG_USE_SEGGER_RTT=y
#Without the following RTT will cease output after complaining about so many dropped messages
#CONFIG_LOG_BACKEND_RTT=n


#More Additions
CONFIG_BT_CENTRAL=y
CONFIG_BT_SCAN=y
CONFIG_BT_SCAN_FILTER_ENABLE=y
CONFIG_BT_SCAN_UUID_CNT=1
#CONFIG_BT_CTLR_PHY_2M=y
CONFIG_BT_CTLR_PHY_CODED=y
CONFIG_BT_SCAN_NAME_CNT=1

CONFIG_BT_CTLR_TX_PWR_DYNAMIC_CONTROL=y
#CONFIG_BT_CTLR_TX_PWR_PLUS_8=y
#CONFIG_BT_CTLR_TX_PWR_PLUS_4=y
#CONFIG_BT_CTLR_TX_PWR_0=y
#CONFIG_BT_CTLR_TX_PWR_MINUS_8=y
#CONFIG_BT_CTLR_TX_PWR_MINUS_12=y
#CONFIG_BT_CTLR_TX_PWR_MINUS_16=y
#CONFIG_BT_CTLR_TX_PWR_MINUS_20=y
#CONFIG_BT_CTLR_TX_PWR_MINUS_40=y
#CONFIG_BT_CTLR_TX_PWR_MINUS_4=y
#CONFIG_BT_CTLR_ADVANCED_FEATURES=y
CONFIG_BT_CTLR_CONN_RSSI=y
