#
# Copyright (c) 2022 Nordic Semiconductor ASA
#
# SPDX-License-Identifier: LicenseRef-Nordic-5-Clause
#

# nRF5340 Audio
CONFIG_NRF5340_AUDIO=y

# Custom config
CONFIG_AUDIO_SOURCE_I2S=y
CONFIG_TRANSPORT_BIS=y

CONFIG_FIFO_FRAME_SPLIT_NUM=10
CONFIG_FIFO_TX_FRAME_COUNT=6
CONFIG_FIFO_RX_FRAME_COUNT=1

# minimum bitrate
CONFIG_LC3_BITRATE=32000
CONFIG_BT_AUDIO_BROADCAST_16_2_1=y

# configuration ok, for 4 streams
#CONFIG_LC3_BITRATE=48000
#CONFIG_BT_AUDIO_BROADCAST_24_2_1=y

#doesn't work for 4 channels
#CONFIG_LC3_BITRATE=96000

CONFIG_AUDIO_SAMPLE_RATE_16000_HZ=y
CONFIG_AUDIO_BIT_DEPTH_16=y

CONFIG_BT_AUDIO_BROADCAST_SRC_STREAM_COUNT=6
CONFIG_BT_AUDIO_BROADCAST_SNK_STREAM_COUNT=6

CONFIG_BT_ISO_MAX_CHAN=6
CONFIG_BT_ISO_TX_BUF_COUNT=6
CONFIG_BT_ISO_TX_FRAG_COUNT=6

CONFIG_BT_EXT_ADV_MAX_ADV_SET=6
CONFIG_BT_ISO_TX_MTU=500
CONFIG_BT_ISO_MAX_BIG=2

# Bluetooth buffer configuration
# default 27
CONFIG_BT_BUF_ACL_TX_SIZE=83
#default 3
CONFIG_BT_BUF_ACL_TX_COUNT=6
#default 68
CONFIG_BT_BUF_EVT_RX_SIZE=255
#default 58
CONFIG_BT_BUF_EVT_DISCARDABLE_SIZE=255
#default 3
CONFIG_BT_BUF_EVT_DISCARDABLE_COUNT=10
#default 255
CONFIG_BT_BUF_CMD_TX_SIZE=255
#default 10
CONFIG_BT_BUF_CMD_TX_COUNT=20

CONFIG_BT_CTLR_ADV_ISO_PDU_LEN_MAX=???

#default n
CONFIG_BT_HCI_TX_STACK_SIZE_WITH_PROMPT=y
#default 1024
CONFIG_BT_HCI_TX_STACK_SIZE=2048

CONFIG_BT_AUDIO_BROADCAST_SRC_COUNT=2
#CONFIG_BT_BUF_ACL_
#CONFIG_BT_BUF_ACL_

CONFIG_BT_LIM_ADV_TIMEOUT=120

CONFIG_LC3_ENC_CHAN_MAX=6
CONFIG_ENCODER_STACK_SIZE=16384
CONFIG_AUDIO_DATAPATH_STACK_SIZE=16384

CONFIG_MAIN_LOG_LEVEL_DBG=y
CONFIG_AUDIO_SYSTEM_LOG_LEVEL_DBG=y
CONFIG_SW_CODEC_SELECT_LOG_LEVEL_DBG=y
CONFIG_BLE_LOG_LEVEL_DBG=y
CONFIG_BT_LOG_LEVEL_DBG=y
CONFIG_BT_AUDIO_DEBUG_STREAM=y
CONFIG_BT_AUDIO_DEBUG_STREAM_DATA=y
CONFIG_BT_AUDIO_DEBUG_BROADCAST_SOURCE=y

CONFIG_STREAMCTRL_LOG_LEVEL_DBG=y
CONFIG_BT_AUDIO_DEBUG_STREAM=y

CONFIG_LOG_DEFAULT_LEVEL=4
CONFIG_THREAD_ANALYZER=y

# General
CONFIG_DEBUG=y
CONFIG_DEBUG_INFO=y
CONFIG_ASSERT=y
CONFIG_STACK_USAGE=y
CONFIG_THREAD_RUNTIME_STATS=y
CONFIG_STACK_SENTINEL=y
CONFIG_INIT_STACKS=y

# Uart driver
CONFIG_SERIAL=y

# Logging
CONFIG_LOG=y
CONFIG_NEWLIB_LIBC_FLOAT_PRINTF=y
CONFIG_LOG_TAG_MAX_LEN=2
CONFIG_LOG_TAG_DEFAULT="--"
CONFIG_LOG_PROCESS_THREAD_SLEEP_MS=500
CONFIG_LOG_PROCESS_THREAD_STACK_SIZE=8192
CONFIG_LOG_BUFFER_SIZE=65536
CONFIG_LOG_SPEED=y

## Avoid redundant warnings for endpoint setting in USB stack
CONFIG_USB_DRIVER_LOG_LEVEL_ERR=y
CONFIG_USB_DEVICE_LOG_LEVEL_ERR=y

# Console related defines
CONFIG_CONSOLE=y
CONFIG_RTT_CONSOLE=y
CONFIG_UART_CONSOLE=y

# Shell related defines
CONFIG_SHELL=y
CONFIG_KERNEL_SHELL=y
CONFIG_USE_SEGGER_RTT=y
## Disable logs on RTT
CONFIG_SHELL_RTT_INIT_LOG_LEVEL_NONE=y
CONFIG_SHELL_BACKEND_RTT=y
CONFIG_SHELL_BACKEND_SERIAL=n
CONFIG_SHELL_VT100_COLORS=y
CONFIG_SHELL_STACK_SIZE=1024
CONFIG_SHELL_CMD_BUFF_SIZE=128
## Reduce shell memory usage
CONFIG_SHELL_WILDCARD=n
CONFIG_SHELL_HELP_ON_WRONG_ARGUMENT_COUNT=n
CONFIG_SHELL_STATS=n
CONFIG_SHELL_CMDS=n
CONFIG_SHELL_HISTORY=y

# Turn off default shell commands
CONFIG_I2C_SHELL=n
CONFIG_HWINFO_SHELL=n
CONFIG_CLOCK_CONTROL_NRF_SHELL=n
CONFIG_FLASH_SHELL=n
CONFIG_DEVICE_SHELL=n

# Suppress err msg from sd_check_card_type. Because SPI_SDHC has no card presence method,
# assume card is in slot. Thus error message is always shown if card is not inserted
CONFIG_SD_LOG_LEVEL_OFF=y
CONFIG_NVS_LOG_LEVEL_WRN=y

CONFIG_CPU_LOAD=y
CONFIG_CPU_LOAD_LOG_PERIODIC=y
CONFIG_CPU_LOAD_LOG_INTERVAL=2000