/** * Copyright (c) 2014 - 2020, Nordic Semiconductor ASA * * All rights reserved. * * Redistribution and use in source and binary forms, with or without modification, * are permitted provided that the following conditions are met: * * 1. Redistributions of source code must retain the above copyright notice, this * list of conditions and the following disclaimer. * * 2. Redistributions in binary form, except as embedded into a Nordic * Semiconductor ASA integrated circuit in a product or a software update for * such product, must reproduce the above copyright notice, this list of * conditions and the following disclaimer in the documentation and/or other * materials provided with the distribution. * * 3. Neither the name of Nordic Semiconductor ASA nor the names of its * contributors may be used to endorse or promote products derived from this * software without specific prior written permission. * * 4. This software, with or without modification, must only be used with a * Nordic Semiconductor ASA integrated circuit. * * 5. Any software provided in binary form under this license must not be reverse * engineered, decompiled, modified and/or disassembled. * * THIS SOFTWARE IS PROVIDED BY NORDIC SEMICONDUCTOR ASA "AS IS" AND ANY EXPRESS * OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES * OF MERCHANTABILITY, NONINFRINGEMENT, AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL NORDIC SEMICONDUCTOR ASA OR CONTRIBUTORS BE * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE * GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT * OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * */ /** @file * * @defgroup ble_sdk_uart_over_ble_main main.c * @{ * @ingroup ble_sdk_app_nus_eval * @brief UART over BLE application main file. * * This file contains the source code for a sample application that uses the Nordic UART service. * This application uses the @ref srvlib_conn_params module. */ #include #include #include "ble_db_discovery.h" #include "nordic_common.h" #include "nrf.h" #include "boards.h" #include "app_error.h" #include "ble.h" #include "ble_err.h" #include "ble_hci.h" #include "ble_srv_common.h" #include "ble_advdata.h" #include "ble_conn_params.h" #include "ble_conn_state.h" #include "nrf_sdh.h" #include "nrf_sdh_ble.h" #include "app_timer.h" #include "app_button.h" #include "ble_lbs.h" #include "nrf_ble_gatt.h" #include "nrf_ble_qwr.h" #include "nrf_pwr_mgmt.h" #include "ble_nus.h" #include "ble_nus_c.h" #include "app_uart.h" #include "app_util_platform.h" #include "ble_advertising.h" #include "nrf_log.h" #include "nrf_log_ctrl.h" #include "nrf_log_default_backends.h" #include "bsp_btn_ble.h" #include "ble_nus_c.h" #include "nrf_ble_scan.h" #include "nrf_wdt.h" #include "nrf_delay.h" #include "nrf_drv_twi.h" #include "ble_tps.h" #include "ble_ias.h" #include "ble_lls.h" #include "ble_bas.h" #include "ble_ias_c.h" #include "peer_manager.h" #include "peer_manager_handler.h" #include "fds.h" #include "nrf_soc.h" #include "nrf_drv_saadc.h" #include "app_pwm.h" #define I2C_24C128_SLAVE_ADDR 0x50 //#define I2C_24C128_SLAVE_ADDR 0x57 //(0xA0 >> 1) /* Common addresses definition for temperature sensor. */ #define LM75B_ADDR (0x90U >> 1) #define LM75B_REG_TEMP 0x00U #define LM75B_REG_CONF 0x01U #define LM75B_REG_THYST 0x02U #define LM75B_REG_TOS 0x03U #define DS1307_ADDR (0x68) #define DS1307_SEC (0x00) #define DS1307_MIN (0x01) #define DS1307_HRS (0x02) #define DS1307_DAY (0x03) #define DS1307_DATE (0x04) #define DS1307_MONTH (0x05) #define DS1307_YEAR (0x06) /* Define version of GCC. */ #define GCC_VERSION (__GNUC__ * 10000 \ + __GNUC_MINOR__ * 100 \ + __GNUC_PATCHLEVEL__) /** * @brief Structure for holding sum of samples from accelerometer. */ #ifdef __GNUC_PATCHLEVEL__ #if GCC_VERSION < 50505 #pragma GCC diagnostic push #pragma GCC diagnostic ignored "-Wmissing-braces" // Hack to GCC 4.9.3 bug. Can be deleted after switch on using GCC 5.0.0 #endif #endif /* Buffer for samples. */ #ifdef __GNUC_PATCHLEVEL__ #if GCC_VERSION < 50505 #pragma GCC diagnostic pop #endif #endif uint8_t t[6]={0}; uint8_t RTC_flag=0, a_flag=0, x_flag=0,z_flag=0; uint16_t batt_lvl_in_milli_volts; uint8_t percentage_batt_lvl; uint8_t battery_buffer[3]; extern uint8_t flag2; unsigned long int time_counter = 0, temp_counter = 0, temp_counter2 = 1; /* Indicates if operation on TWI has ended. */ static volatile bool m_xfer_done = false; /* TWI instance. */ uint8_t data_array[237]; uint8_t hexs[16]; static const nrf_drv_twi_t m_twi_mma_EEP = NRF_DRV_TWI_INSTANCE(0); /* Buffer for samples read from temperature sensor. */ static uint8_t m_sample[3]; void eep_WriteByte(uint16_t eep_address, unsigned char val); unsigned char eep_readByte(uint16_t eep_address); ret_code_t err_codecpy; extern uint8_t gateway_flag; //uint8_t *device_name; uint8_t new_arr[240] = {0}; //uint8_t new_arr2[100]; //uint16_t count=0; APP_TIMER_DEF(tx_timer); #if defined (UART_PRESENT) #include "nrf_uart.h" #endif #if defined (UARTE_PRESENT) #include "nrf_uarte.h" #endif #include "nrf_log.h" #include "nrf_log_ctrl.h" #include "nrf_log_default_backends.h" #include "bsp.h" #define APP_BLE_CONN_CFG_TAG 1 /**< A tag identifying the SoftDevice BLE configuration. */ //#define DEVICE_NAME "tag_d598" /**< Name of device. Will be included in the advertising data. */ //#define DEVICE_NAME "tag_af27" /**< Name of device. Will be included in the advertising data. */ //#define DEVICE_NAME "tag_c035" /**< Name of device. Will be included in the advertising data. */ //#define DEVICE_NAME "tag_59A7" /**< Name of device. Will be included in the advertising data. */ //#define DEVICE_NAME "tag_9526" /**< Name of device. Will be included in the advertising data. */ //#define DEVICE_NAME "tag_3454" /**< Name of device. Will be included in the advertising data. */ //#define DEVICE_NAME "tag_2721" /**< Name of device. Will be included in the advertising data. */ //#define DEVICE_NAME "tag_153c" /**< Name of device. Will be included in the advertising data. */ //#define DEVICE_NAME "tag_7212" /**< Name of device. Will be included in the advertising data. */ //#define DEVICE_NAME "tag_dff5" /**< Name of device. Will be included in the advertising data. */ //#define DEVICE_NAME "tag_3420" /**< Name of device. Will be included in the advertising data. */ //#define DEVICE_NAME "tag_d110" /**< Name of device. Will be included in the advertising data. */ //#define DEVICE_NAME "tag_e138" /**< Name of device. Will be included in the advertising data. */ //#define DEVICE_NAME "tag_2c39" /**< Name of device. Will be included in the advertising data. */ //#define DEVICE_NAME "tag_c878" /**< Name of device. Will be included in the advertising data. */ //#define DEVICE_NAME "tag_ed29" /**< Name of device. Will be included in the advertising data. */ //#define DEVICE_NAME "tag_f4f8" /**< Name of device. Will be included in the advertising data. */ //#define DEVICE_NAME "tag_ddce" /**< Name of device. Will be included in the advertising data. */ //#define DEVICE_NAME "tag_ed29" /**< Name of device. Will be included in the advertising data. */ //#define DEVICE_NAME "tag_fd84" /**< Name of device. Will be included in the advertising data. */ //#define DEVICE_NAME "tag_6577" /**< Name of device. Will be included in the advertising data. */ #define DEVICE_NAME "tag_c586" /**< Name of device. Will be included in the advertising data. */ //#define DEVICE_NAME "tag_e138" /**< Name of device. Will be included in the advertising data. */ //#define DEVICE_NAME "t_68dd_cell" /**< Name of device. Will be included in the advertising data. */ #define APP_BLE_OBSERVER_PRIO 3 /**< Application's BLE observer priority. You shouldn't need to modify this value. */ #define APP_BLE_CONN_CFG_TAG 1 /**< A tag identifying the SoftDevice BLE configuration. */ #define BATTERY_LEVEL_MEAS_INTERVAL APP_TIMER_TICKS(120000) /**< Battery level measurement interval (ticks). This value corresponds to 120 seconds. */ #define MIN_CONN_INTERVAL MSEC_TO_UNITS(500, UNIT_1_25_MS) /**< Minimum acceptable connection interval (0.5 seconds). */ #define MAX_CONN_INTERVAL MSEC_TO_UNITS(1000, UNIT_1_25_MS) /**< Maximum acceptable connection interval (1 second). */ #define SLAVE_LATENCY 0 /**< Slave latency. */ #define CONN_SUP_TIMEOUT MSEC_TO_UNITS(4000, UNIT_10_MS) /**< Connection supervisory timeout (4 seconds). */ #define APP_ADV_INTERVAL 40 /**< The advertising interval (in units of 0.625 ms. This value corresponds to 25 ms). */ #define APP_ADV_DURATION 0 /**< The advertising duration (180 seconds) in units of 10 milliseconds. */ #define FIRST_CONN_PARAMS_UPDATE_DELAY APP_TIMER_TICKS(5000) /**< Time from initiating event (connect or start of notification) to first time sd_ble_gap_conn_param_update is called (5 seconds). */ #define NEXT_CONN_PARAMS_UPDATE_DELAY APP_TIMER_TICKS(30000) /**< Time between each call to sd_ble_gap_conn_param_update after the first call (30 seconds). */ #define MAX_CONN_PARAMS_UPDATE_COUNT 3 /**< Number of attempts before giving up the connection parameter negotiation. */ #define SEC_PARAM_BOND 1 /**< Perform bonding. */ #define SEC_PARAM_MITM 0 /**< Man In The Middle protection not required. */ #define SEC_PARAM_LESC 0 /**< LE Secure Connections not enabled. */ #define SEC_PARAM_KEYPRESS 0 /**< Keypress notifications not enabled. */ #define SEC_PARAM_IO_CAPABILITIES BLE_GAP_IO_CAPS_NONE /**< No I/O capabilities. */ #define SEC_PARAM_OOB 0 /**< Out Of Band data not available. */ #define SEC_PARAM_MIN_KEY_SIZE 7 /**< Minimum encryption key size. */ #define SEC_PARAM_MAX_KEY_SIZE 16 /**< Maximum encryption key size. */ #define INITIAL_LLS_ALERT_LEVEL BLE_CHAR_ALERT_LEVEL_NO_ALERT /**< Initial value for the Alert Level characteristic in the Link Loss service. */ #define TX_POWER_LEVEL (+0) /**< TX Power Level value. This will be set both in the TX Power service, in the advertising data, and also used to set the radio transmit power. */ #define ADC_REF_VOLTAGE_IN_MILLIVOLTS 600 /**< Reference voltage (in milli volts) used by ADC while doing conversion. */ #define ADC_PRE_SCALING_COMPENSATION 6 /**< The ADC is configured to use VDD with 1/3 prescaling as input. And hence the result of conversion is to be multiplied by 3 to get the actual value of the battery voltage.*/ #define DIODE_FWD_VOLT_DROP_MILLIVOLTS 270 /**< Typical forward voltage drop of the diode . */ #define ADC_RES_10BIT 1024 /**< Maximum digital value for 10-bit ADC conversion. */ #define DEAD_BEEF 0xDEADBEEF /**< Value used as error code on stack dump, can be used to identify stack location on stack unwind. */ #define NUS_SERVICE_UUID_TYPE BLE_UUID_TYPE_VENDOR_BEGIN /**< UUID type for the Nordic UART Service (vendor specific). */ #define ECHOBACK_BLE_UART_DATA 1 /**< Echo the UART data that is received over the Nordic UART Service (NUS) back to the sender. */ #define UART_TX_BUF_SIZE 256 /**< UART TX buffer size. */ #define UART_RX_BUF_SIZE 256 /**< UART RX buffer size. */ #define NOTIFICATION_INTERVAL APP_TIMER_TICKS(1000) /**@brief Macro to convert the result of ADC conversion in millivolts. * * @param[in] ADC_VALUE ADC result. * * @retval Result converted to millivolts. */ #define ADC_RESULT_IN_MILLI_VOLTS(ADC_VALUE)\ ((((ADC_VALUE) * ADC_REF_VOLTAGE_IN_MILLIVOLTS) / ADC_RES_10BIT) * ADC_PRE_SCALING_COMPENSATION) //static ble_gap_adv_params_t m_adv_params; /**< Parameters to be passed to the stack when starting advertising. */ //static uint8_t m_adv_handle = BLE_GAP_ADV_SET_HANDLE_NOT_SET; /**< Advertising handle used to identify an advertising set. */ //static uint8_t m_enc_advdata[BLE_GAP_ADV_SET_DATA_SIZE_MAX]; /**< Buffer for storing an encoded advertising set. */ //APP_TIMER_DEF(m_battery_timer_id); /**< Battery measurement timer. */ BLE_TPS_DEF(m_tps); /**< TX Power service instance. */ BLE_IAS_DEF(m_ias, NRF_SDH_BLE_TOTAL_LINK_COUNT); /**< Immediate Alert service instance. */ BLE_LLS_DEF(m_lls); /**< Link Loss service instance. */ BLE_BAS_DEF(m_bas); /**< Battery service instance. */ BLE_IAS_C_DEF(m_ias_c); /**< Immediate Alert Service client instance. */ //NRF_BLE_GATT_DEF(m_gatt); /**< GATT module instance. */ //NRF_BLE_QWR_DEF(m_qwr); /**< Context for the Queued Write module.*/ BLE_ADVERTISING_DEF(m_advertising); /**< Advertising module instance. */ BLE_DB_DISCOVERY_DEF(m_ble_db_discovery); /**< DB discovery module instance. */ //NRF_BLE_GQ_DEF(m_ble_gatt_queue, /**< BLE GATT Queue instance. */ // NRF_SDH_BLE_PERIPHERAL_LINK_COUNT, // NRF_BLE_GQ_QUEUE_SIZE); static volatile bool m_is_high_alert_signalled; /**< Variable to indicate whether a high alert has been signalled to the peer. */ static volatile bool m_is_ias_present = false; /**< Variable to indicate whether the immediate alert service has been discovered at the connected peer. */ static nrf_saadc_value_t adc_buf[2]; nrf_saadc_value_t adc_result; static void on_ias_evt(ble_ias_t * p_ias, ble_ias_evt_t * p_evt); static void on_lls_evt(ble_lls_t * p_lls, ble_lls_evt_t * p_evt); static void on_ias_c_evt(ble_ias_c_t * p_lls, ble_ias_c_evt_t * p_evt); static void on_bas_evt(ble_bas_t * p_bas, ble_bas_evt_t * p_evt); //static void advertising_init(void); static void advertising_start(); BLE_NUS_C_DEF(m_ble_nus_c); /**< BLE Nordic UART Service (NUS) client instance. */ BLE_NUS_DEF(m_nus, NRF_SDH_BLE_TOTAL_LINK_COUNT); /**< BLE NUS service instance. */ NRF_BLE_GATT_DEF(m_gatt); /**< GATT module instance. */ NRF_BLE_QWR_DEF(m_qwr); /**< Context for the Queued Write module.*/ //BLE_ADVERTISING_DEF(m_advertising); /**< Advertising module instance. */ NRF_BLE_SCAN_DEF(m_scan); /**< Scanning Module instance. */ NRF_BLE_GQ_DEF(m_ble_gatt_queue, /**< BLE GATT Queue instance. */ NRF_SDH_BLE_CENTRAL_LINK_COUNT, NRF_BLE_GQ_QUEUE_SIZE); static uint16_t m_conn_handle = BLE_CONN_HANDLE_INVALID; /**< Handle of the current connection. */ static uint16_t m_ble_nus_max_data_len = BLE_GATT_ATT_MTU_DEFAULT - 3; /**< Maximum length of data (in bytes) that can be transmitted to the peer by the Nordic UART service module. */ static ble_uuid_t m_adv_uuids[] = /**< Universally unique service identifier. */ { {BLE_UUID_NUS_SERVICE, NUS_SERVICE_UUID_TYPE} }; /**@brief NUS UUID. */ static ble_uuid_t const m_nus_uuid = { .uuid = BLE_UUID_NUS_SERVICE, .type = NUS_SERVICE_UUID_TYPE }; /**@brief Function for handling Service errors. * * @details A pointer to this function will be passed to each service which may need to inform the * application about an error. * * @param[in] nrf_error Error code containing information about what went wrong. */ static void service_error_handler(uint32_t nrf_error) { APP_ERROR_HANDLER(nrf_error); } /**@brief Function for handling Peer Manager events. * * @param[in] p_evt Peer Manager event. */ static void pm_evt_handler(pm_evt_t const * p_evt) { pm_handler_on_pm_evt(p_evt); pm_handler_flash_clean(p_evt); switch (p_evt->evt_id) { case PM_EVT_PEERS_DELETE_SUCCEEDED: advertising_start(false); break; default: break; } } /**@brief Function for handling the ADC interrupt. * * @details This function will fetch the conversion result from the ADC, convert the value into * percentage and send it to peer. */ void saadc_event_handler(nrf_drv_saadc_evt_t const * p_event) { if (p_event->type == NRF_DRV_SAADC_EVT_DONE) { //nrf_saadc_value_t adc_result; //uint16_t batt_lvl_in_milli_volts; //uint8_t percentage_batt_lvl; uint32_t err_code; adc_result = p_event->data.done.p_buffer[0]; printf("\n%d",adc_result); err_code = nrf_drv_saadc_buffer_convert(p_event->data.done.p_buffer, 1); APP_ERROR_CHECK(err_code); batt_lvl_in_milli_volts = ADC_RESULT_IN_MILLI_VOLTS(adc_result) + DIODE_FWD_VOLT_DROP_MILLIVOLTS; percentage_batt_lvl = battery_level_in_percent(batt_lvl_in_milli_volts); printf("\n%d",batt_lvl_in_milli_volts); printf("\n%d",percentage_batt_lvl); err_code = ble_bas_battery_level_update(&m_bas, percentage_batt_lvl, BLE_CONN_HANDLE_ALL); //eep_WriteByte(130,percentage_batt_lvl); if ((err_code != NRF_SUCCESS) && (err_code != NRF_ERROR_INVALID_STATE) && (err_code != NRF_ERROR_RESOURCES) && (err_code != NRF_ERROR_BUSY) && (err_code != BLE_ERROR_GATTS_SYS_ATTR_MISSING) ) { APP_ERROR_HANDLER(err_code); } } } /**@brief Function for handling database discovery events. * * @details This function is callback function to handle events from the database discovery module. * Depending on the UUIDs that are discovered, this function should forward the events * to their respective services. * * @param[in] p_event Pointer to the database discovery event. */ static void db_disc_handler(ble_db_discovery_evt_t * p_evt) { ble_ias_c_on_db_disc_evt(&m_ias_c, p_evt); } /**@brief Function for configuring ADC to do battery level conversion. */ static void adc_configure(void) { ret_code_t err_code = nrf_drv_saadc_init(NULL, saadc_event_handler); APP_ERROR_CHECK(err_code); nrf_saadc_channel_config_t config = NRF_DRV_SAADC_DEFAULT_CHANNEL_CONFIG_SE(NRF_SAADC_INPUT_VDD); err_code = nrf_drv_saadc_channel_init(0, &config); APP_ERROR_CHECK(err_code); err_code = nrf_drv_saadc_buffer_convert(&adc_buf[0], 1); APP_ERROR_CHECK(err_code); err_code = nrf_drv_saadc_buffer_convert(&adc_buf[1], 1); APP_ERROR_CHECK(err_code); } /** * @brief Function for setting active mode on MMA7660 accelerometer. */ void DS3231_set_mode(void) { ret_code_t err_code; uint8_t reg[2] = {0x00,0x05}; err_code = nrf_drv_twi_tx(&m_twi_mma_EEP,DS1307_ADDR, reg, sizeof(reg), false); APP_ERROR_CHECK(err_code); //uint8_t reg1[8] = {DS1307_SEC,0x20,0x13,0x12,0x02,0x30,0x04,0x21}; //err_code = nrf_drv_twi_tx(&m_twi_mma_EEP,DS1307_ADDR, reg1, sizeof(reg1), false); //APP_ERROR_CHECK(err_code); //while (m_xfer_done == false); } /** * @brief Function for handling data from temperature sensor. * * @param[in] temp Temperature in Celsius degrees read from sensor. */ __STATIC_INLINE void data_handler(uint8_t *temp) { //NRF_LOG_INFO("Temperature: %d Celsius degrees.", temp); //printf("%2x:%2x:%2x", // temp[2], // temp[1], // temp[0] // ); // printf("\n"); time_counter++; if(time_counter == temp_counter + 17) { printf("%2x:%2x:%2x", temp[2], temp[1], temp[0] ); printf("\n"); } if(time_counter == temp_counter + 18) { printf("%2x:%2x", temp[1], temp[2] ); } if(time_counter == temp_counter + 19){ printf(":%2x",temp[0]); printf("\n"); temp_counter = time_counter; } } /**@brief Function for handling the Battery measurement timer timeout. * * @details This function will be called each time the battery level measurement timer expires. * This function will start the ADC. * * @param[in] p_context Pointer used for passing some arbitrary information (context) from the * app_start_timer() call to the timeout handler. */ static void battery_level_meas_timeout_handler(void * p_context) { UNUSED_PARAMETER(p_context); ret_code_t err_code; err_code = nrf_drv_saadc_sample(); APP_ERROR_CHECK(err_code); } /** * @brief TWI events handler. */ void twi_handler(nrf_drv_twi_evt_t const * p_event, void * p_context) { switch (p_event->type) { case NRF_DRV_TWI_EVT_DONE: if (p_event->xfer_desc.type == NRF_DRV_TWI_XFER_RX) { data_handler(m_sample); //printf("%2x",m_sample[0]); //printf("\n"); } m_xfer_done = true; break; default: break; } } void twi_init (void) { ret_code_t err_code; //ret_code_t ret; const nrf_drv_twi_config_t twi_mma_EEP_config = { .scl = ARDUINO_SCL_PIN, .sda = ARDUINO_SDA_PIN, .frequency = NRF_TWI_FREQ_100K, .interrupt_priority = APP_IRQ_PRIORITY_HIGH }; err_code = nrf_drv_twi_init(&m_twi_mma_EEP, &twi_mma_EEP_config, NULL, NULL); //twi_handler APP_ERROR_CHECK(err_code); nrf_drv_twi_enable(&m_twi_mma_EEP); err_codecpy=err_code; nrf_delay_ms(5); } unsigned char eep_readByte(uint16_t eep_address){ unsigned char eep_by_address[2]; unsigned char reg=0; eep_by_address[1] = eep_address; eep_by_address[0] = (unsigned char)(eep_address << 8); // setting the start address nrf_drv_twi_tx(&m_twi_mma_EEP, I2C_24C128_SLAVE_ADDR, eep_by_address, 2, true); // read a byte nrf_drv_twi_rx(&m_twi_mma_EEP, I2C_24C128_SLAVE_ADDR, ®,1); nrf_delay_ms(5); return reg; } void eep_WriteByte(uint16_t eep_address, unsigned char val){ unsigned char eep_by_address[3]; eep_by_address[2] = val; eep_by_address[1] = eep_address; eep_by_address[0] = (unsigned char)(eep_address << 8); nrf_drv_twi_tx(&m_twi_mma_EEP, I2C_24C128_SLAVE_ADDR, eep_by_address, 3, false); nrf_delay_ms(5); } //-----send message------// void send_message() { ble_conn_state_conn_handle_list_t conn_handles = ble_conn_state_periph_handles(); uint32_t err_code; uint16_t length = 237; //uint8_t data_array[237]; //uint8_t data_array[240] = "9ECADC240EE5A9E093F39ECADC240EE5A9E093F39ECADC240EE5A9E093F39ECADC240EE5A9E093F39ECADC240EE5A9E093F39ECADC240EE5A9E093F39ECADC240EE5A9E093F39ECADC240EE5A9E093F39ECADC240EE5A9E093F39ECADC240EE5A9E093F39ECADC240EE5A9E093FZ"; for(int i =0;i<128;i++) data_array[i]= new_arr[i]; data_array[128] = hexs[0]; //'C'; data_array[129] = hexs[1]; //'8'; data_array[130] = hexs[2]; //'7'; data_array[131] = hexs[3]; //'8'; data_array[132] = hexs[4]; //'A'; data_array[133] = hexs[5]; //'1'; data_array[134] = hexs[6]; //'E'; data_array[135] = hexs[7]; //'3'; data_array[136] = hexs[8]; //'F'; data_array[137] = hexs[9]; //'4'; data_array[138] = hexs[10]; //'D'; data_array[139] = hexs[11]; //'C'; // data_array[140] = battery_buffer[0]; // data_array[141] = battery_buffer[1]; // data_array[142] = '%'; for(int i =140;i<236;i++) data_array[i]= new_arr[i]; NRF_LOG_DEBUG("Ready to send data over BLE NUS"); printf("Ready to send data over BLE NUS"); NRF_LOG_HEXDUMP_DEBUG(data_array, length); do { for (uint8_t i = 0; i < conn_handles.len; i++) //--this does not work { m_conn_handle = conn_handles.conn_handles[i]; printf("\r\nconnection handle length: %d", conn_handles.conn_handles[i]); err_code = ble_nus_data_send(&m_nus, data_array, &length, m_conn_handle); //bsp_board_led_off(2); } //err_code = ble_nus_data_send(&m_nus, data_array, &length, m_conn_handle);-- This works printf("\r\nerror code: %d", err_code); if ((err_code != NRF_ERROR_INVALID_STATE) && (err_code != NRF_ERROR_RESOURCES) && (err_code != NRF_ERROR_NOT_FOUND)) { APP_ERROR_CHECK(err_code); } //bsp_board_led_off(2); //bsp_board_led_off(3); //bsp_board_led_off(1); //nrf_delay_ms(5000); } while (err_code == NRF_ERROR_RESOURCES); if(err_code == NRF_SUCCESS) { printf("\r\n message sent\r\n"); for(uint8_t i=0;i<6;i++) { bsp_board_led_off(2); nrf_delay_ms(100); bsp_board_led_on(2); nrf_delay_ms(100); } for(uint8_t i=0;i<300;i++) { eep_WriteByte(i,0xFF); } } } //-----send message------// /**@brief Function for assert macro callback. * * @details This function will be called in case of an assert in the SoftDevice. * * @warning This handler is an example only and does not fit a final product. You need to analyse * how your product is supposed to react in case of Assert. * @warning On assert from the SoftDevice, the system can only recover on reset. * * @param[in] line_num Line number of the failing ASSERT call. * @param[in] p_file_name File name of the failing ASSERT call. */ void assert_nrf_callback(uint16_t line_num, const uint8_t * p_file_name) { app_error_handler(DEAD_BEEF, line_num, p_file_name); } /**@brief Function for the Timer initialization. * * @details Initializes the timer module. */ static void timers_init(void) { // Initialize timer module, making it use the scheduler ret_code_t err_code = app_timer_init(); APP_ERROR_CHECK(err_code); err_code = app_timer_create(&tx_timer, APP_TIMER_MODE_REPEATED, System_ticks_incrementals); } /**@brief Function for the GAP initialization. * * @details This function will set up all the necessary GAP (Generic Access Profile) parameters of * the device. It also sets the permissions and appearance. */ static void gap_params_init(void) { uint32_t err_code; ble_gap_conn_params_t gap_conn_params; ble_gap_conn_sec_mode_t sec_mode; BLE_GAP_CONN_SEC_MODE_SET_OPEN(&sec_mode); err_code = sd_ble_gap_device_name_set(&sec_mode, (const uint8_t *) DEVICE_NAME, strlen(DEVICE_NAME)); APP_ERROR_CHECK(err_code); memset(&gap_conn_params, 0, sizeof(gap_conn_params)); gap_conn_params.min_conn_interval = MIN_CONN_INTERVAL; gap_conn_params.max_conn_interval = MAX_CONN_INTERVAL; gap_conn_params.slave_latency = SLAVE_LATENCY; gap_conn_params.conn_sup_timeout = CONN_SUP_TIMEOUT; err_code = sd_ble_gap_ppcp_set(&gap_conn_params); APP_ERROR_CHECK(err_code); } /**@brief Function for handling Queued Write Module errors. * * @details A pointer to this function will be passed to each service which may need to inform the * application about an error. * * @param[in] nrf_error Error code containing information about what went wrong. */ static void nrf_qwr_error_handler(uint32_t nrf_error) { APP_ERROR_HANDLER(nrf_error); } /**@brief Function for handling the Nordic UART Service Client errors. * * @param[in] nrf_error Error code containing information about what went wrong. */ static void nus_error_handler(uint32_t nrf_error) { APP_ERROR_HANDLER(nrf_error); } /**@brief Function to start scanning. */ static void scan_start(void) { ret_code_t ret; ret = nrf_ble_scan_start(&m_scan); APP_ERROR_CHECK(ret); ret = bsp_indication_set(BSP_INDICATE_SCANNING); APP_ERROR_CHECK(ret); } /**@brief Function for handling Scanning Module events. */ static void scan_evt_handler(scan_evt_t const * p_scan_evt) { ret_code_t err_code; switch(p_scan_evt->scan_evt_id) { case NRF_BLE_SCAN_EVT_CONNECTING_ERROR: { err_code = p_scan_evt->params.connecting_err.err_code; APP_ERROR_CHECK(err_code); } break; case NRF_BLE_SCAN_EVT_CONNECTED: { ble_gap_evt_connected_t const * p_connected = p_scan_evt->params.connected.p_connected; // Scan is automatically stopped by the connection. NRF_LOG_INFO("Connecting to target %02x%02x%02x%02x%02x%02x", p_connected->peer_addr.addr[0], p_connected->peer_addr.addr[1], p_connected->peer_addr.addr[2], p_connected->peer_addr.addr[3], p_connected->peer_addr.addr[4], p_connected->peer_addr.addr[5] ); } break; case NRF_BLE_SCAN_EVT_SCAN_TIMEOUT: { NRF_LOG_INFO("Scan timed out."); scan_start(); } break; default: break; } } /**@brief Function for initializing the scanning and setting the filters. */ static void scan_init(void) { ret_code_t err_code; nrf_ble_scan_init_t init_scan; memset(&init_scan, 0, sizeof(init_scan)); init_scan.connect_if_match = true; init_scan.conn_cfg_tag = APP_BLE_CONN_CFG_TAG; err_code = nrf_ble_scan_init(&m_scan, &init_scan, scan_evt_handler); APP_ERROR_CHECK(err_code); err_code = nrf_ble_scan_filter_set(&m_scan, SCAN_UUID_FILTER, &m_nus_uuid); APP_ERROR_CHECK(err_code); err_code = nrf_ble_scan_filters_enable(&m_scan, NRF_BLE_SCAN_UUID_FILTER, false); APP_ERROR_CHECK(err_code); } /**@brief Function for handling the data from the Nordic UART Service. * * @details This function will process the data received from the Nordic UART BLE Service and send * it to the UART module. * * @param[in] p_evt Nordic UART Service event. */ /**@brief Function for handling database discovery events. * * @details This function is a callback function to handle events from the database discovery module. * Depending on the UUIDs that are discovered, this function forwards the events * to their respective services. * * @param[in] p_event Pointer to the database discovery event. */ //static void db_disc_handler(ble_db_discovery_evt_t * p_evt) //{ // ble_nus_c_on_db_disc_evt(&m_ble_nus_c, p_evt); //} /**@snippet [Handling the data received over BLE] */ static void nus_data_handler(ble_nus_evt_t * p_evt) { if (p_evt->type == BLE_NUS_EVT_RX_DATA) { uint32_t err_code; NRF_LOG_DEBUG("Received data from BLE NUS. Writing data on UART."); NRF_LOG_HEXDUMP_DEBUG(p_evt->params.rx_data.p_data, p_evt->params.rx_data.length); for (uint32_t i = 0; i < p_evt->params.rx_data.length; i++) { do { err_code = app_uart_put(p_evt->params.rx_data.p_data[i]); if ((err_code != NRF_SUCCESS) && (err_code != NRF_ERROR_BUSY)) { NRF_LOG_ERROR("Failed receiving NUS message. Error 0x%x. ", err_code); APP_ERROR_CHECK(err_code); } } while (err_code == NRF_ERROR_BUSY); } if (p_evt->params.rx_data.p_data[p_evt->params.rx_data.length - 1] == '\r') { while (app_uart_put('\n') == NRF_ERROR_BUSY); } } } /**@snippet [Handling the data received over BLE] */ /**@brief Function for initializing the Queued Write module. */ static void qwr_init(void) { ret_code_t err_code; nrf_ble_qwr_init_t qwr_init_obj = {0}; // Initialize Queued Write Module. qwr_init_obj.error_handler = nrf_qwr_error_handler; err_code = nrf_ble_qwr_init(&m_qwr, &qwr_init_obj); APP_ERROR_CHECK(err_code); } /**@brief Function for initializing the TX Power Service. */ static void tps_init(void) { ret_code_t err_code; ble_tps_init_t tps_init_obj; memset(&tps_init_obj, 0, sizeof(tps_init_obj)); tps_init_obj.initial_tx_power_level = TX_POWER_LEVEL; tps_init_obj.tpl_rd_sec = SEC_JUST_WORKS; err_code = ble_tps_init(&m_tps, &tps_init_obj); APP_ERROR_CHECK(err_code); } /**@brief Function for initializing the Immediate Alert Service. */ static void ias_init(void) { ret_code_t err_code; ble_ias_init_t ias_init_obj; memset(&ias_init_obj, 0, sizeof(ias_init_obj)); ias_init_obj.evt_handler = on_ias_evt; ias_init_obj.alert_wr_sec = SEC_JUST_WORKS; err_code = ble_ias_init(&m_ias, &ias_init_obj); APP_ERROR_CHECK(err_code); } /**@brief Function for initializing the Link Loss Service. */ static void lls_init(void) { ret_code_t err_code; ble_lls_init_t lls_init_obj; // Initialize Link Loss Service memset(&lls_init_obj, 0, sizeof(lls_init_obj)); lls_init_obj.evt_handler = on_lls_evt; lls_init_obj.error_handler = service_error_handler; lls_init_obj.initial_alert_level = INITIAL_LLS_ALERT_LEVEL; lls_init_obj.alert_level_rd_sec = SEC_JUST_WORKS; lls_init_obj.alert_level_wr_sec = SEC_JUST_WORKS; err_code = ble_lls_init(&m_lls, &lls_init_obj); APP_ERROR_CHECK(err_code); } /**@brief Function for initializing the Battery Service. */ static void bas_init(void) { ret_code_t err_code; ble_bas_init_t bas_init_obj; memset(&bas_init_obj, 0, sizeof(bas_init_obj)); bas_init_obj.evt_handler = on_bas_evt; bas_init_obj.support_notification = true; bas_init_obj.p_report_ref = NULL; bas_init_obj.initial_batt_level = 100; bas_init_obj.bl_rd_sec = SEC_OPEN; bas_init_obj.bl_cccd_wr_sec = SEC_OPEN; bas_init_obj.bl_report_rd_sec = SEC_OPEN; err_code = ble_bas_init(&m_bas, &bas_init_obj); APP_ERROR_CHECK(err_code); } /**@brief Function for initializing the immediate alert service client. * * @details This will initialize the client side functionality of the Find Me profile. */ static void ias_client_init(void) { ret_code_t err_code; ble_ias_c_init_t ias_c_init_obj; memset(&ias_c_init_obj, 0, sizeof(ias_c_init_obj)); m_is_high_alert_signalled = false; ias_c_init_obj.evt_handler = on_ias_c_evt; ias_c_init_obj.error_handler = service_error_handler; ias_c_init_obj.p_gatt_queue = &m_ble_gatt_queue; err_code = ble_ias_c_init(&m_ias_c, &ias_c_init_obj); APP_ERROR_CHECK(err_code); } /**@brief Function for initializing services that will be used by the application. */ static void services_init(void) { uint32_t err_code; ble_nus_init_t nus_init; nrf_ble_qwr_init_t qwr_init = {0}; // Initialize Queued Write Module. qwr_init.error_handler = nrf_qwr_error_handler; err_code = nrf_ble_qwr_init(&m_qwr, &qwr_init); APP_ERROR_CHECK(err_code); // Initialize NUS. memset(&nus_init, 0, sizeof(nus_init)); nus_init.data_handler = nus_data_handler; err_code = ble_nus_init(&m_nus, &nus_init); APP_ERROR_CHECK(err_code); //qwr_init(); tps_init(); ias_init(); lls_init(); //bas_init(); ias_client_init(); } /**@brief Function for the Signals alert event from Immediate Alert or Link Loss services. * * @param[in] alert_level Requested alert level. */ static void alert_signal(uint8_t alert_level) { ret_code_t err_code; switch (alert_level) { case BLE_CHAR_ALERT_LEVEL_NO_ALERT: NRF_LOG_INFO("No Alert."); err_code = bsp_indication_set(BSP_INDICATE_ALERT_OFF); APP_ERROR_CHECK(err_code); break; // BLE_CHAR_ALERT_LEVEL_NO_ALERT case BLE_CHAR_ALERT_LEVEL_MILD_ALERT: NRF_LOG_INFO("Mild Alert."); err_code = bsp_indication_set(BSP_INDICATE_ALERT_0); APP_ERROR_CHECK(err_code); break; // BLE_CHAR_ALERT_LEVEL_MILD_ALERT case BLE_CHAR_ALERT_LEVEL_HIGH_ALERT: NRF_LOG_INFO("HIGH Alert."); err_code = bsp_indication_set(BSP_INDICATE_ALERT_3); APP_ERROR_CHECK(err_code); break; // BLE_CHAR_ALERT_LEVEL_HIGH_ALERT default: // No implementation needed. break; } } /**@brief Function for handling Immediate Alert events. * * @details This function will be called for all Immediate Alert events which are passed to the * application. * * @param[in] p_ias Immediate Alert structure. * @param[in] p_evt Event received from the Immediate Alert service. */ static void on_ias_evt(ble_ias_t * p_ias, ble_ias_evt_t * p_evt) { switch (p_evt->evt_type) { case BLE_IAS_EVT_ALERT_LEVEL_UPDATED: if (p_evt->p_link_ctx != NULL) { alert_signal(p_evt->p_link_ctx->alert_level); } break; // BLE_IAS_EVT_ALERT_LEVEL_UPDATED default: // No implementation needed. break; } } /**@brief Function for handling Link Loss events. * * @details This function will be called for all Link Loss events which are passed to the * application. * * @param[in] p_lls Link Loss structure. * @param[in] p_evt Event received from the Link Loss service. */ static void on_lls_evt(ble_lls_t * p_lls, ble_lls_evt_t * p_evt) { switch (p_evt->evt_type) { case BLE_LLS_EVT_LINK_LOSS_ALERT: alert_signal(p_evt->params.alert_level); break; // BLE_LLS_EVT_LINK_LOSS_ALERT default: // No implementation needed. break; } } /**@brief Function for handling IAS Client events. * * @details This function will be called for all IAS Client events which are passed to the * application. * * @param[in] p_ias_c IAS Client structure. * @param[in] p_evt Event received. */ static void on_ias_c_evt(ble_ias_c_t * p_ias_c, ble_ias_c_evt_t * p_evt) { ret_code_t err_code; switch (p_evt->evt_type) { case BLE_IAS_C_EVT_DISCOVERY_COMPLETE: // IAS is found on peer. The Find Me Locator functionality of this app will work. err_code = ble_ias_c_handles_assign(&m_ias_c, p_evt->conn_handle, p_evt->alert_level.handle_value); APP_ERROR_CHECK(err_code); m_is_ias_present = true; break; // BLE_IAS_C_EVT_DISCOVERY_COMPLETE case BLE_IAS_C_EVT_DISCOVERY_FAILED: // IAS is not found on peer. The Find Me Locator functionality of this app will NOT work. break; // BLE_IAS_C_EVT_DISCOVERY_FAILED case BLE_IAS_C_EVT_DISCONN_COMPLETE: // Disable alert buttons m_is_ias_present = false; break; // BLE_IAS_C_EVT_DISCONN_COMPLETE default: break; } } /**@brief Function for handling the Battery Service events. * * @details This function will be called for all Battery Service events which are passed to the | application. * * @param[in] p_bas Battery Service structure. * @param[in] p_evt Event received from the Battery Service. */ static void on_bas_evt(ble_bas_t * p_bas, ble_bas_evt_t * p_evt) { ret_code_t err_code; switch (p_evt->evt_type) { case BLE_BAS_EVT_NOTIFICATION_ENABLED: // Start battery timer err_code = app_timer_start(tx_timer, BATTERY_LEVEL_MEAS_INTERVAL, NULL); APP_ERROR_CHECK(err_code); break; // BLE_BAS_EVT_NOTIFICATION_ENABLED case BLE_BAS_EVT_NOTIFICATION_DISABLED: err_code = app_timer_stop(tx_timer); APP_ERROR_CHECK(err_code); break; // BLE_BAS_EVT_NOTIFICATION_DISABLED default: // No implementation needed. break; } } static void peer_manager_init(void) { ble_gap_sec_params_t sec_param; ret_code_t err_code; err_code = pm_init(); APP_ERROR_CHECK(err_code); memset(&sec_param, 0, sizeof(ble_gap_sec_params_t)); // Security parameters to be used for all security procedures. sec_param.bond = SEC_PARAM_BOND; sec_param.mitm = SEC_PARAM_MITM; sec_param.lesc = SEC_PARAM_LESC; sec_param.keypress = SEC_PARAM_KEYPRESS; sec_param.io_caps = SEC_PARAM_IO_CAPABILITIES; sec_param.oob = SEC_PARAM_OOB; sec_param.min_key_size = SEC_PARAM_MIN_KEY_SIZE; sec_param.max_key_size = SEC_PARAM_MAX_KEY_SIZE; sec_param.kdist_own.enc = 1; sec_param.kdist_own.id = 1; sec_param.kdist_peer.enc = 1; sec_param.kdist_peer.id = 1; err_code = pm_sec_params_set(&sec_param); APP_ERROR_CHECK(err_code); err_code = pm_register(pm_evt_handler); APP_ERROR_CHECK(err_code); } /**@brief Function for handling characters received by the Nordic UART Service (NUS). * * @details This function takes a list of characters of length data_len and prints the characters out on UART. * If @ref ECHOBACK_BLE_UART_DATA is set, the data is sent back to sender. */ static void ble_nus_chars_received_uart_print(uint8_t * p_data, uint16_t data_len) { ret_code_t ret_val; NRF_LOG_DEBUG("Receiving data."); NRF_LOG_HEXDUMP_DEBUG(p_data, data_len); for (uint32_t i = 0; i < data_len; i++) { do { ret_val = app_uart_put(p_data[i]); if ((ret_val != NRF_SUCCESS) && (ret_val != NRF_ERROR_BUSY)) { NRF_LOG_ERROR("app_uart_put failed for index 0x%04x.", i); APP_ERROR_CHECK(ret_val); } } while (ret_val == NRF_ERROR_BUSY); } if (p_data[data_len-1] == '\r') { while (app_uart_put('\n') == NRF_ERROR_BUSY); } if (ECHOBACK_BLE_UART_DATA) { // Send data back to the peripheral. do { ret_val = ble_nus_c_string_send(&m_ble_nus_c, p_data, data_len); if ((ret_val != NRF_SUCCESS) && (ret_val != NRF_ERROR_BUSY)) { NRF_LOG_ERROR("Failed sending NUS message. Error 0x%x. ", ret_val); APP_ERROR_CHECK(ret_val); } } while (ret_val == NRF_ERROR_BUSY); } } /**@brief Function for handling an event from the Connection Parameters Module. * * @details This function will be called for all events in the Connection Parameters Module * which are passed to the application. * * @note All this function does is to disconnect. This could have been done by simply setting * the disconnect_on_fail config parameter, but instead we use the event handler * mechanism to demonstrate its use. * * @param[in] p_evt Event received from the Connection Parameters Module. */ static void on_conn_params_evt(ble_conn_params_evt_t * p_evt) { uint32_t err_code; if (p_evt->evt_type == BLE_CONN_PARAMS_EVT_FAILED) { err_code = sd_ble_gap_disconnect(m_conn_handle, BLE_HCI_CONN_INTERVAL_UNACCEPTABLE); APP_ERROR_CHECK(err_code); } } /**@brief Function for handling errors from the Connection Parameters module. * * @param[in] nrf_error Error code containing information about what went wrong. */ static void conn_params_error_handler(uint32_t nrf_error) { APP_ERROR_HANDLER(nrf_error); } /**@brief Function for initializing the Connection Parameters module. */ static void conn_params_init(void) { uint32_t err_code; ble_conn_params_init_t cp_init; memset(&cp_init, 0, sizeof(cp_init)); cp_init.p_conn_params = NULL; cp_init.first_conn_params_update_delay = FIRST_CONN_PARAMS_UPDATE_DELAY; cp_init.next_conn_params_update_delay = NEXT_CONN_PARAMS_UPDATE_DELAY; cp_init.max_conn_params_update_count = MAX_CONN_PARAMS_UPDATE_COUNT; cp_init.start_on_notify_cccd_handle = BLE_GATT_HANDLE_INVALID; cp_init.disconnect_on_fail = false; cp_init.evt_handler = on_conn_params_evt; cp_init.error_handler = conn_params_error_handler; err_code = ble_conn_params_init(&cp_init); APP_ERROR_CHECK(err_code); } /**@brief Function for putting the chip into sleep mode. * * @note This function will not return. */ static void sleep_mode_enter(void) { uint32_t err_code = bsp_indication_set(BSP_INDICATE_IDLE); APP_ERROR_CHECK(err_code); // Prepare wakeup buttons. err_code = bsp_btn_ble_sleep_mode_prepare(); APP_ERROR_CHECK(err_code); // Go to system-off mode (this function will not return; wakeup will cause a reset). err_code = sd_power_system_off(); APP_ERROR_CHECK(err_code); } /**@brief Function for handling advertising events. * * @details This function will be called for advertising events which are passed to the application. * * @param[in] ble_adv_evt Advertising event. */ static void on_adv_evt(ble_adv_evt_t ble_adv_evt) { uint32_t err_code; switch (ble_adv_evt) { case BLE_ADV_EVT_FAST: err_code = bsp_indication_set(BSP_INDICATE_ADVERTISING); APP_ERROR_CHECK(err_code); break; case BLE_ADV_EVT_IDLE: sleep_mode_enter(); break; default: break; } } /**@snippet [Handling events from the ble_nus_c module] */ static void ble_nus_c_evt_handler(ble_nus_c_t * p_ble_nus_c, ble_nus_c_evt_t const * p_ble_nus_evt) { ret_code_t err_code; switch (p_ble_nus_evt->evt_type) { case BLE_NUS_C_EVT_DISCOVERY_COMPLETE: NRF_LOG_INFO("Discovery complete."); err_code = ble_nus_c_handles_assign(p_ble_nus_c, p_ble_nus_evt->conn_handle, &p_ble_nus_evt->handles); APP_ERROR_CHECK(err_code); err_code = ble_nus_c_tx_notif_enable(p_ble_nus_c); APP_ERROR_CHECK(err_code); NRF_LOG_INFO("Connected to device with Nordic UART Service."); break; case BLE_NUS_C_EVT_NUS_TX_EVT: ble_nus_chars_received_uart_print(p_ble_nus_evt->p_data, p_ble_nus_evt->data_len); break; case BLE_NUS_C_EVT_DISCONNECTED: NRF_LOG_INFO("Disconnected."); scan_start(); break; } } /**@snippet [Handling events from the ble_nus_c module] */ /**@brief Function for handling BLE events. * * @param[in] p_ble_evt Bluetooth stack event. * @param[in] p_context Unused. */ static void ble_evt_handler(ble_evt_t const * p_ble_evt, void * p_context) { uint32_t err_code; switch (p_ble_evt->header.evt_id) { case BLE_GAP_EVT_CONNECTED: NRF_LOG_INFO("Connected"); err_code = bsp_indication_set(BSP_INDICATE_CONNECTED); APP_ERROR_CHECK(err_code); m_conn_handle = p_ble_evt->evt.gap_evt.conn_handle; err_code = nrf_ble_qwr_conn_handle_assign(&m_qwr, m_conn_handle); APP_ERROR_CHECK(err_code); break; case BLE_GAP_EVT_DISCONNECTED: NRF_LOG_INFO("Disconnected"); // LED indication will be changed when advertising starts. m_conn_handle = BLE_CONN_HANDLE_INVALID; break; case BLE_GAP_EVT_PHY_UPDATE_REQUEST: { NRF_LOG_DEBUG("PHY update request."); ble_gap_phys_t const phys = { .rx_phys = BLE_GAP_PHY_AUTO, .tx_phys = BLE_GAP_PHY_AUTO, }; err_code = sd_ble_gap_phy_update(p_ble_evt->evt.gap_evt.conn_handle, &phys); APP_ERROR_CHECK(err_code); } break; case BLE_GAP_EVT_SEC_PARAMS_REQUEST: // Pairing not supported err_code = sd_ble_gap_sec_params_reply(m_conn_handle, BLE_GAP_SEC_STATUS_PAIRING_NOT_SUPP, NULL, NULL); APP_ERROR_CHECK(err_code); break; case BLE_GATTS_EVT_SYS_ATTR_MISSING: // No system attributes have been stored. err_code = sd_ble_gatts_sys_attr_set(m_conn_handle, NULL, 0, 0); APP_ERROR_CHECK(err_code); break; case BLE_GATTC_EVT_TIMEOUT: // Disconnect on GATT Client timeout event. err_code = sd_ble_gap_disconnect(p_ble_evt->evt.gattc_evt.conn_handle, BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION); APP_ERROR_CHECK(err_code); break; case BLE_GATTS_EVT_TIMEOUT: // Disconnect on GATT Server timeout event. err_code = sd_ble_gap_disconnect(p_ble_evt->evt.gatts_evt.conn_handle, BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION); APP_ERROR_CHECK(err_code); break; default: // No implementation needed. break; } } /**@brief Function for the SoftDevice initialization. * * @details This function initializes the SoftDevice and the BLE event interrupt. */ static void ble_stack_init(void) { ret_code_t err_code; err_code = nrf_sdh_enable_request(); APP_ERROR_CHECK(err_code); // Configure the BLE stack using the default settings. // Fetch the start address of the application RAM. uint32_t ram_start = 0; err_code = nrf_sdh_ble_default_cfg_set(APP_BLE_CONN_CFG_TAG, &ram_start); APP_ERROR_CHECK(err_code); // Enable BLE stack. err_code = nrf_sdh_ble_enable(&ram_start); APP_ERROR_CHECK(err_code); // Register a handler for BLE events. NRF_SDH_BLE_OBSERVER(m_ble_observer, APP_BLE_OBSERVER_PRIO, ble_evt_handler, NULL); } /**@brief Function for handling events from the GATT library. */ void gatt_evt_handler(nrf_ble_gatt_t * p_gatt, nrf_ble_gatt_evt_t const * p_evt) { if ((m_conn_handle == p_evt->conn_handle) && (p_evt->evt_id == NRF_BLE_GATT_EVT_ATT_MTU_UPDATED)) { m_ble_nus_max_data_len = p_evt->params.att_mtu_effective - OPCODE_LENGTH - HANDLE_LENGTH; NRF_LOG_INFO("Data len is set to 0x%X(%d)", m_ble_nus_max_data_len, m_ble_nus_max_data_len); } NRF_LOG_DEBUG("ATT MTU exchange completed. central 0x%x peripheral 0x%x", p_gatt->att_mtu_desired_central, p_gatt->att_mtu_desired_periph); } /**@brief Function for initializing the GATT library. */ void gatt_init(void) { ret_code_t err_code; err_code = nrf_ble_gatt_init(&m_gatt, gatt_evt_handler); APP_ERROR_CHECK(err_code); err_code = nrf_ble_gatt_att_mtu_periph_set(&m_gatt, NRF_SDH_BLE_GATT_MAX_MTU_SIZE); APP_ERROR_CHECK(err_code); } /**@brief Function for handling events from the BSP module. * * @param[in] event Event generated by button press. */ void bsp_event_handler(bsp_event_t event) { uint32_t err_code; switch (event) { case BSP_EVENT_SLEEP: sleep_mode_enter(); break; case BSP_EVENT_DISCONNECT: err_code = sd_ble_gap_disconnect(m_conn_handle, BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION); if (err_code != NRF_ERROR_INVALID_STATE) { APP_ERROR_CHECK(err_code); } break; case BSP_EVENT_WHITELIST_OFF: if (m_conn_handle == BLE_CONN_HANDLE_INVALID) { err_code = ble_advertising_restart_without_whitelist(&m_advertising); if (err_code != NRF_ERROR_INVALID_STATE) { APP_ERROR_CHECK(err_code); } } break; default: break; } } /**@brief Function for handling app_uart events. * * @details This function will receive a single character from the app_uart module and append it to * a string. The string will be be sent over BLE when the last character received was a * 'new line' '\n' (hex 0x0A) or if the string has reached the maximum data length. */ /**@snippet [Handling the data received over UART] */ void uart_event_handle(app_uart_evt_t * p_event) { static uint8_t data_array[BLE_NUS_MAX_DATA_LEN]; static uint8_t index = 0; uint32_t err_code; switch (p_event->evt_type) { case APP_UART_DATA_READY: UNUSED_VARIABLE(app_uart_get(&data_array[index])); index++; if ((data_array[index - 1] == '\n') || (data_array[index - 1] == '\r') || (index >= m_ble_nus_max_data_len)) { if (index > 1) { NRF_LOG_DEBUG("Ready to send data over BLE NUS"); NRF_LOG_HEXDUMP_DEBUG(data_array, index); do { uint16_t length = (uint16_t)index; err_code = ble_nus_data_send(&m_nus, data_array, &length, m_conn_handle); if ((err_code != NRF_ERROR_INVALID_STATE) && (err_code != NRF_ERROR_RESOURCES) && (err_code != NRF_ERROR_NOT_FOUND)) { APP_ERROR_CHECK(err_code); } } while (err_code == NRF_ERROR_RESOURCES); } index = 0; } break; case APP_UART_COMMUNICATION_ERROR: APP_ERROR_HANDLER(p_event->data.error_communication); break; case APP_UART_FIFO_ERROR: APP_ERROR_HANDLER(p_event->data.error_code); break; default: break; } } /**@snippet [Handling the data received over UART] */ /**@brief Function for initializing the UART module. */ /**@snippet [UART Initialization] */ static void uart_init(void) { uint32_t err_code; app_uart_comm_params_t const comm_params = { .rx_pin_no = RX_PIN_NUMBER, .tx_pin_no = TX_PIN_NUMBER, .rts_pin_no = RTS_PIN_NUMBER, .cts_pin_no = CTS_PIN_NUMBER, .flow_control = APP_UART_FLOW_CONTROL_ENABLED, .use_parity = false, #if defined (UART_PRESENT) .baud_rate = NRF_UART_BAUDRATE_115200 #else .baud_rate = NRF_UARTE_BAUDRATE_115200 #endif }; APP_UART_FIFO_INIT(&comm_params, UART_RX_BUF_SIZE, UART_TX_BUF_SIZE, uart_event_handle, APP_IRQ_PRIORITY_LOWEST, err_code); APP_ERROR_CHECK(err_code); } /**@snippet [UART Initialization] */ /**@brief Function for initializing the Advertising functionality. */ static void advertising_init(void) { uint32_t err_code; ble_advertising_init_t init; uint8_t power_level = 0x08; memset(&init, 0, sizeof(init)); init.advdata.name_type = BLE_ADVDATA_FULL_NAME; init.advdata.include_appearance = false; init.advdata.flags = BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE; init.advdata.p_tx_power_level = &power_level; init.srdata.uuids_complete.uuid_cnt = sizeof(m_adv_uuids) / sizeof(m_adv_uuids[0]); init.srdata.uuids_complete.p_uuids = m_adv_uuids; init.config.ble_adv_fast_enabled = true; init.config.ble_adv_fast_interval = APP_ADV_INTERVAL; init.config.ble_adv_fast_timeout = APP_ADV_DURATION; init.evt_handler = on_adv_evt; err_code = ble_advertising_init(&m_advertising, &init); APP_ERROR_CHECK(err_code); ble_advertising_conn_cfg_tag_set(&m_advertising, APP_BLE_CONN_CFG_TAG); //err_code = sd_ble_gap_tx_power_set(BLE_GAP_TX_POWER_ROLE_ADV, m_adv_handle, (-10)); //APP_ERROR_CHECK(err_code); } /**@brief Function for initializing the Nordic UART Service (NUS) client. */ static void nus_c_init(void) { ret_code_t err_code; ble_nus_c_init_t init; init.evt_handler = ble_nus_c_evt_handler; init.error_handler = nus_error_handler; init.p_gatt_queue = &m_ble_gatt_queue; err_code = ble_nus_c_init(&m_ble_nus_c, &init); APP_ERROR_CHECK(err_code); } /**@brief Function for initializing buttons and leds. * * @param[out] p_erase_bonds Will be true if the clear bonding button was pressed to wake the application up. */ /**@brief Function for initializing buttons and leds. */ static void buttons_leds_init(void) { ret_code_t err_code; bsp_event_t startup_event; err_code = bsp_init(BSP_INIT_LEDS, bsp_event_handler); APP_ERROR_CHECK(err_code); err_code = bsp_btn_ble_init(NULL, &startup_event); APP_ERROR_CHECK(err_code); } /**@brief Function for initializing the nrf log module. */ static void log_init(void) { ret_code_t err_code = NRF_LOG_INIT(NULL); APP_ERROR_CHECK(err_code); NRF_LOG_DEFAULT_BACKENDS_INIT(); } /**@brief Function for initializing power management. */ static void power_management_init(void) { ret_code_t err_code; err_code = nrf_pwr_mgmt_init(); APP_ERROR_CHECK(err_code); } volatile uint32_t system_ticks = 0; void System_ticks_incrementals() { system_ticks++; } /** @brief Function for initializing the database discovery module. */ static void db_discovery_init(void) { ble_db_discovery_init_t db_init; memset(&db_init, 0, sizeof(ble_db_discovery_init_t)); db_init.evt_handler = db_disc_handler; db_init.p_gatt_queue = &m_ble_gatt_queue; ret_code_t err_code = ble_db_discovery_init(&db_init); APP_ERROR_CHECK(err_code); } /**@brief Function for handling the idle state (main loop). * * @details If there is no pending log operation, then sleep until next the next event occurs. */ static void idle_state_handle(void) { if (NRF_LOG_PROCESS() == false) { nrf_pwr_mgmt_run(); } } /**@brief Clear bond information from persistent storage. */ static void delete_bonds(void) { ret_code_t err_code; NRF_LOG_INFO("Erase bonds!"); err_code = pm_peers_delete(); APP_ERROR_CHECK(err_code); } /**@brief Function for starting advertising. */ static void advertising_start(void) { uint32_t err_code = ble_advertising_start(&m_advertising, BLE_ADV_MODE_FAST); APP_ERROR_CHECK(err_code); } /**@brief Function for changing the tx power. */ static void tx_power_set(void) { ret_code_t err_code = sd_ble_gap_tx_power_set(BLE_GAP_TX_POWER_ROLE_ADV, m_advertising.adv_handle, TX_POWER_LEVEL); APP_ERROR_CHECK(err_code); } int byteArrayToHexString(uint8_t *byte_array, int byte_array_len, char *hexstr, int hexstr_len) { int off = 0; int i = 0;; uint8_t A = 0; uint8_t B = 0; while(off < byte_array_len) { A = (byte_array[off]>>4) & 0x0f; B = (byte_array[off]) & 0x0f; if(A >= 0u && A < 0x0au) { hexstr[i] = A+0x30; } else if(A >= 0x0au && A <= 0x0fu) { hexstr[i] = A+55u; } if(B >= 0u && B < 0x0au) { hexstr[i+1] = B+0x30; } else if(B >= 0x0au && B <= 0x0fu) { hexstr[i+1] = B+55u; } i = i+2; off++; } hexstr[hexstr_len] = '\0'; return off; } void Read_data(){ // reading byte-by-byte from EEPROM for (int i = 0; i < 128; i++) { uint8_t readValue = eep_readByte(i); //if (readValue == 0) { // break; //} char readValueChar = (char)(readValue); printf("%c", readValueChar); new_arr[i]=readValueChar; } } void Read_time_data(){ // reading byte-by-byte from EEPROM for (int i = 140; i < 236; i++) { uint8_t readValue = eep_readByte(i); //if (readValue == 0) { // break; //} char readValueChar = (char)(readValue); printf("%c", readValueChar); new_arr[i]=readValueChar; } } uint8_t HR = 0; uint8_t MN = 0; uint8_t SS = 0; uint8_t DD = 0; uint8_t MM = 0; uint8_t YY = 0; uint8_t c =0; /** * @brief Function for reading data from ds3231. */ void read_sensor_data() { //m_xfer_done = false; /* Read 1 byte from the specified address - skip 3 bits dedicated for fractional part of temperature. */ ret_code_t err_code = nrf_drv_twi_rx(&m_twi_mma_EEP, DS1307_ADDR, (uint8_t*)&m_sample, 3); //APP_ERROR_CHECK(err_code); //nrf_delay_ms(2000); if(time_counter == temp_counter + 19) // if(c == 3) { t[0]= m_sample[2]; t[1]= m_sample[1]; t[2]= m_sample[0]; temp_counter = time_counter; } if(time_counter == temp_counter2 + 19) // if(c == 3) { t[3]= m_sample[1]; t[4]= m_sample[2]; t[5]= 0x21; temp_counter2 = time_counter; } //if(m_sample[2] == 0x88){ // printf("%2x:%2x:%2x", // m_sample[2], // m_sample[1], // m_sample[0] // ); // printf("\n"); // c++; // } // nrf_delay_ms(30); time_counter++; // if(time_counter == temp_counter + 38) // { // //if(RTC_flag == 1) // { // a_flag=1; // t[0]= m_sample[2]; // t[1]= m_sample[1]; // t[2]= m_sample[0]; // //HR= m_sample[2]; // //MN= m_sample[1]; // //SS= m_sample[0]; // } // } //if(time_counter == temp_counter + 39) //{ // //if(RTC_flag == 1) // { // x_flag=1; // t[3]= m_sample[1]; // t[4]= m_sample[2]; // } //} //if(time_counter == temp_counter + 40) //{ // //if(RTC_flag == 1) // { // z_flag=1; // t[5]= m_sample[0]; // } // temp_counter = time_counter; //} } /**@brief Application main function. */ int main(void) { static ble_gap_addr_t mac_addr; ret_code_t err_code; bool erase_bonds; ble_evt_t const * p_ble_evt; void * p_contex; log_init(); uart_init(); printf("\r\nUART started begin.\r\n"); buttons_leds_init(); buzzer_off(); //leds_init(); //buttons_init(); //power_management_init(); timers_init(); app_timer_start(tx_timer, NOTIFICATION_INTERVAL, NULL); db_discovery_init(); adc_configure(); peer_manager_init(); ble_stack_init(); gap_params_init(); gatt_init(); nus_c_init(); services_init(); advertising_init(); conn_params_init(); advertising_start(); scan_init(); twi_init(); DS3231_set_mode(); // Start execution. NRF_LOG_INFO("peripheral example started."); //app_timer_start(tx_timer, NOTIFICATION_INTERVAL, NULL); //app_timer_start(tx_timer, NOTIFICATION_INTERVAL, NULL); err_code = sd_ble_gap_addr_get((ble_gap_addr_t*)(&mac_addr)); byteArrayToHexString((uint8_t *)mac_addr.addr, 6, hexs, 12); tx_power_set(); scan_start(); bsp_board_led_on(0); bsp_board_led_on(1); bsp_board_led_on(2); bsp_board_led_on(3); Read_data(); Read_time_data(); //int battery_status = eep_readByte(130); //if(battery_status == 100){ // battery_status = 99; //} //itoa (battery_status, battery_buffer, 10); //printf("\n%d", battery_status); //if(battery_status < 20){ // for(int i =0; i<5;i++) // { // bsp_board_led_off(1); // bsp_board_led_off(2); // nrf_delay_ms(200); // bsp_board_led_on(1); // bsp_board_led_on(2); // nrf_delay_ms(200); // } //} //sd_ble_gap_tx_power_set(BLE_GAP_TX_POWER_ROLE_ADV, m_adv_handle, (-10)); //app_timer_start(tx_timer, 16UL, NULL); //nrf_delay_ms(1000); while(1) { nrf_delay_ms(10); read_sensor_data(); } } uint32_t get_System_ticks() { return system_ticks; } /** * @} */