/*
* Copyright (c) 2017, STMicroelectronics - All Rights Reserved
*
* This file is part of VL53L1 Core and is dual licensed,
* either 'STMicroelectronics
* Proprietary license'
* or 'BSD 3-clause "New" or "Revised" License' , at your option.
*
********************************************************************************
*
* 'STMicroelectronics Proprietary license'
*
********************************************************************************
*
* License terms: STMicroelectronics Proprietary in accordance with licensing
* terms at www.st.com/sla0081
*
* STMicroelectronics confidential
* Reproduction and Communication of this document is strictly prohibited unless
* specifically authorized in writing by STMicroelectronics.
*
*
********************************************************************************
*
* Alternatively, VL53L1 Core may be distributed under the terms of
* 'BSD 3-clause "New" or "Revised" License', in which case the following
* provisions apply instead of the ones mentioned above :
*
********************************************************************************
*
* License terms: BSD 3-clause "New" or "Revised" License.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* 1. Redistributions of source code must retain the above copyright notice, this
* list of conditions and the following disclaimer.
*
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
*
* 3. Neither the name of the copyright holder nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
*
********************************************************************************
*
*/

/**
 * @file  vl53l1_wait.h
 *
 * @brief EwokPlus25 low level Driver wait function definitions
 */

#ifndef _VL53L1_WAIT_H_
#define _VL53L1_WAIT_H_

#include "vl53l1_platform.h"

#ifdef __cplusplus
extern "C" {
#endif


/**
 * @brief Wait for initial firmware boot to finish
 *
 * Calls VL53L1_poll_for_boot_completion()
 *
 * @param[in]   Dev           : Device handle
 *
 * @return  VL53L1_ERROR_NONE     Success
 * @return  "Other error code"    See ::VL53L1_Error
 */

VL53L1_Error VL53L1_wait_for_boot_completion(
	VL53L1_DEV      Dev);


/**
 * @brief Waits for initial firmware ready
 *
 * Only waits to see if the firmware is ready in timed and
 * single shot modes.
 *
 * Calls VL53L1_poll_for_firmware_ready()
 *
 * @param[in]   Dev           : Device handle
 *
 * @return  VL53L1_ERROR_NONE     Success
 * @return  "Other error code"    See ::VL53L1_Error
 */

VL53L1_Error VL53L1_wait_for_firmware_ready(
	VL53L1_DEV      Dev);


/**
 * @brief  Waits for the next ranging interrupt
 *
 * Calls VL53L1_poll_for_range_completion()
 *
 * @param[in]   Dev             :  Device handle
 *
 * @return  VL53L1_ERROR_NONE     Success
 * @return  "Other error code"    See ::VL53L1_Error
 */

VL53L1_Error VL53L1_wait_for_range_completion(
	VL53L1_DEV   Dev);


/**
 * @brief  Waits for a device test mode to complete.

 * Calls VL53L1_poll_for_test_completion()
 *
 * @param[in]   Dev             : Device Handle
 *
 * @return  VL53L1_ERROR_NONE     Success
 * @return  "Other error code"    See ::VL53L1_Error
 */

VL53L1_Error VL53L1_wait_for_test_completion(
	VL53L1_DEV   Dev);




/**
 * @brief Reads FIRMWARE__SYSTEM_STATUS register to detect if the
 *        firmware was finished booting
 *
 * @param[in]   Dev           : Device handle
 * @param[out]  pready        : pointer to data ready flag \n
 *                                 0 = boot not complete \n
 *                                 1 = boot complete
 *
 * @return  VL53L1_ERROR_NONE     Success
 * @return  "Other error code"    See ::VL53L1_Error
 */

VL53L1_Error VL53L1_is_boot_complete(
	VL53L1_DEV      Dev,
	uint8_t        *pready);

/**
 * @brief Reads FIRMWARE__SYSTEM_STATUS register to detect if the
 *        firmware is ready for ranging.
 *
 * @param[in]   Dev           : Device handle
 * @param[out]  pready        : pointer to data ready flag \n
 *                                 0 = firmware not ready \n
 *                                 1 = firmware ready
 *
 * @return  VL53L1_ERROR_NONE     Success
 * @return  "Other error code"    See ::VL53L1_Error
 */

VL53L1_Error VL53L1_is_firmware_ready(
	VL53L1_DEV      Dev,
	uint8_t        *pready);


/**
 * @brief  Reads bit 0 of VL53L1_GPIO__TIO_HV_STATUS register to determine
 *         if new range data is ready (available).
 *
 * Interrupt may be either active high or active low. The behaviour of bit 0
 * of the VL53L1_GPIO__TIO_HV_STATUS register is the same as the interrupt
 * signal generated on the GPIO pin.
 *
 * pdev->stat_cfg.gpio_hv_mux_ctrl bit 4 is used to select required check level
 *
 *
 * @param[in]   Dev           : Device handle
 * @param[out]  pready        : pointer to data ready flag \n
 *                                 0 = data not ready \n
 *                                 1 = new range data available
 *
 * @return  VL53L1_ERROR_NONE     Success
 * @return  "Other error code"    See ::VL53L1_Error
 */

VL53L1_Error VL53L1_is_new_data_ready(
	VL53L1_DEV      Dev,
	uint8_t        *pready);




/**
 * @brief Waits (polls) for initial firmware boot to finish
 *
 * After power on or a device reset via XSHUTDOWN EwokPlus25 firmware takes
 * about 2ms to boot. During this boot sequence elected NVM data is copied
 * to the device's Host & MCU G02 registers
 *
 * This function polls the FIRMWARE__SYSTEM_STATUS register to detect when
 * firmware is ready.
 *
 * Polling is implemented using VL53L1_WaitValueMaskEx()
 *
 * @param[in]   Dev           : Device handle
 * @param[in]   timeout_ms    : Wait timeout in [ms]
 *
 * @return  VL53L1_ERROR_NONE     Success
 * @return  "Other error code"    See ::VL53L1_Error
 */

VL53L1_Error VL53L1_poll_for_boot_completion(
	VL53L1_DEV      Dev,
	uint32_t        timeout_ms);


/**
 * @brief Waits (polls) for initial firmware ready
 *
 * Polling is implemented using VL53L1_WaitValueMaskEx()
 *
 * @param[in]   Dev           : Device handle
 * @param[in]   timeout_ms    : Wait timeout in [ms]
 *
 * @return  VL53L1_ERROR_NONE     Success
 * @return  "Other error code"    See ::VL53L1_Error
 */

VL53L1_Error VL53L1_poll_for_firmware_ready(
	VL53L1_DEV      Dev,
	uint32_t        timeout_ms);


/**
 * @brief  Polls bit 0 of VL53L1_GPIO__TIO_HV_STATUS register to determine
 *         the state of the GPIO (Interrupt) pin.
 *
 * Interrupt may be either active high or active low. The behaviour of bit 0
 * of the VL53L1_GPIO__TIO_HV_STATUS register is the same as the interrupt
 * signal generated on the GPIO pin.
 *
 * pdev->stat_cfg.gpio_hv_mux_ctrl bit 4 is used to select required check level
 *
 * Polling is implemented using VL53L1_WaitValueMaskEx()
 *
 * @param[in]   Dev           :  Device handle
 * @param[in]   timeout_ms    : Wait timeout in [ms]
 *
 * @return  VL53L1_ERROR_NONE     Success
 * @return  "Other error code"    See ::VL53L1_Error
 */

VL53L1_Error VL53L1_poll_for_range_completion(
	VL53L1_DEV   Dev,
	uint32_t     timeout_ms);



#ifdef __cplusplus
}
#endif

#endif /* _VL53L1_WAIT_H_ */