Test condition: -SDK version: v2.2.0 -hci_lpuart * add CONFIG_LOG_BUFFER_SIZE=4096 in prj.conf log ------------------------------------------------------ [14:56:43.288]RX←◆*** Booting Zephyr OS build v3.2.99-ncs1 *** [00:00:00.000,152]  board_control: init: vcom0_pins_routing is ENABLED [00:00:00.000,213]  board_control: init: vcom2_pins_routing is ENABLED [00:00:00.000,274]  board_control: init: led1_pin_routing is ENABLED [00:00:00.000,305]  board_control: init: led2_pin_routing is ENABLED [00:00:00.000,366]  board_control: init: led3_pin_routing is ENABLED [00:00:00.000,396]  board_control: init: led4_pin_routing is ENABLED [00:00:00.000,457]  board_control: init: switch1_pin_routing is ENABLED [00:00:00.000,518]  board_control: init: switch2_pin_routing is ENABLED [00:00:00.000,549]  board_control: init: button1_pin_routing is ENABLED [00:00:00.000,610]  board_control: init: button2_pin_routing is ENABLED [00:00:00.000,671]  board_control: init: nrf_interface_pins_0_2_routing is ENABLED [00:00:00.000,732]  board_control: init: nrf_interface_pins_3_5_routing is ENABLED [00:00:00.000,762]  board_control: init: nrf_interface_pins_6_8_routing is disabled [00:00:00.000,793]  board_control: reset_pin_configure: GPIO reset line enabled on pin P1.02, holding... [00:00:00.000,823]  board_control: init: Board configured. [00:00:00.005,462]  sdc_hci_driver: hci_driver_open: SoftDevice Controller build revision: 6d 90 41 2a 38 e8 ad 17 29 a5 03 38 39 27 d7 85 |m.A*8... )..89'.. 1f 85 d8 e1 |....  [00:00:00.006,072]  bt_hci_raw: bt_enable_raw: Bluetooth enabled in RAW mode [15:08:53.686]RX←◆GPIO reset l [15:08:53.708]RX←◆ine asserted, device reset. Bye @ cycle32 23876461 [15:08:54.384]RX←◆*** Booting Zephyr OS build v3.2.99-ncs1 *** [00:00:00.000,152]  board_control: init: vcom0_pins_routing is ENABLED [00:00:00.000,213]  board_control: init: vcom2_pins_routing is ENABLED [00:00:00.000,274]  board_control: init: led1_pin_routing is ENABLED [00:00:00.000,305]  board_control: ini [15:08:54.446]RX←◆t: led2_pin_routing is ENABLED [00:00:00.000,366]  board_control: init: led3_pin_routing is ENABLED [00:00:00.000,427]  board_control: init: led4_pin_routing is ENABLED [00:00:00.000,457]  board_control: init: switch1_pin_routing is ENABLED [15:08:54.473]RX←◆ [00:00:00.000,518]  board_control: init: switch2_pin_routing is ENABLED [00:00:00.000,579]  board_control: init: button1_pin_routing is ENABLED [00:00:00.000,610]  board_control: init: button2_pin_routing is ENABLED [00:00:00.000,671]  [15:08:54.500]RX←◆[0m board_control: init: nrf_interface_pins_0_2_routing is ENABLED [00:00:00.000,732]  board_control: init: nrf_interface_pins_3_5_routing is ENABLED [00:00:00.000,762]  board_control: init: nrf_interface_pins_6_8_routing is disabled [00:00:00.000,823]  board_control: reset_pin_configure: GPIO reset line enabled on pin P1.02, holding... [00:00:00.000,823]  board_control: init: Board configured. [00:00:00.005,462]  sdc_hci_driver: hci_driver_open: SoftDevice Controller build revision: 6d 90 41 2a 38 e8 ad 17 29 a5 03 38 39 27 d7 85 |m.A*8... )..89'.. 1f 85 d8 e1 [15:08:54.566]RX←◆ |....  [00:00:00.006,072]  bt_hci_raw: bt_enable_raw: Bluetooth enabled in RAW mode