Guidence and Question on Running OTBR using Docker

RE: Guidence and Question on Running OTBR using Docker

SteveKay — Wed, 08 Nov 2023 02:31:27 GMT

In addition to the Steps in the Nordic document mentiond in my intro statement for this post, more commands need to be executed

This is the final step in the document that I was following and the status of the thread node running inside the docker container is disabled.

some more commands to get the thread node running are required.

So at this point I executed all the following commands:

$ sudo docker exec -it otbr sh -c "sudo ot-ctl ifconfig down"

Done

$ sudo docker exec -it otbr sh -c "sudo ot-ctl thread stop"

Done

$ sudo docker exec -it otbr sh -c "sudo ot-ctl dataset init new"

Done

$ sudo docker exec -it otbr sh -c "sudo ot-ctl dataset commit active"

Done

$ sudo docker exec -it otbr sh -c "sudo ot-ctl ifconfig up"

Done

$ sudo docker exec -it otbr sh -c "sudo ot-ctl thread start"

Done

$ sudo docker exec -it otbr sh -c "sudo ot-ctl state"

leader

Done

$ sudo docker exec -it otbr sh -c "sudo ot-ctl netdata show"

Prefixes:

fd48:5276:8095:1::/64 paos low 7400

Routes:

fd48:5276:8095:2:0:0::/96 sn low 7400

fc00::/7 sa med 7400

Services:

44970 01 24000500000e10 s 7400

44970 5d fda89b12bc80717e93014a1b555b31abd11f s 7400

Contexts:

fd48:5276:8095:1::/64 1 c

Done

$ sudo docker exec -it otbr sh -c "sudo ot-ctl ipaddr"

fda8:9b12:bc80:717e:0:ff:fe00:fc11

fd48:5276:8095:1:474b:7213:103a:3cd3

fda8:9b12:bc80:717e:0:ff:fe00:fc10

fda8:9b12:bc80:717e:0:ff:fe00:fc38

fda8:9b12:bc80:717e:0:ff:fe00:fc00

fda8:9b12:bc80:717e:0:ff:fe00:7400

fda8:9b12:bc80:717e:9301:4a1b:555b:31ab

fe80:0:0:0:4c1e:6966:69fb:e265

Done

$ sudo docker exec -it otbr sh -c "sudo service otbr-agent status"

otbr-agent is running

RESULTS

Here are the results of executing the extra commands and the status of the docker container WEB UI showing the status as well.

Now the status of the Thread Node is now reporting "leader".

$ sudo docker exec -it otbr sh -c "sudo ot-ctl state"

leader

Done

The WEB GUI showing the status and the Form menu.

More commands need to be executed

This is the final step in the document that I was following and the status of the thread node running inside the docker container is disabled. At this point i assume that this cannot be a good thing, so I seek some advice from Nordic Devzone and the Discord MakeItMatter Server. I receive some helpful advice from a Nordic moderator on DISCORD. It turns out, that I need to execute some more commands to get the thread node running.

So at this point I executed all the following commands:

$ sudo docker exec -it otbr sh -c "sudo ot-ctl ifconfig down"

Done

$ sudo docker exec -it otbr sh -c "sudo ot-ctl thread stop"

Done

$ sudo docker exec -it otbr sh -c "sudo ot-ctl dataset init new"

Done

$ sudo docker exec -it otbr sh -c "sudo ot-ctl dataset commit active"

Done

$ sudo docker exec -it otbr sh -c "sudo ot-ctl ifconfig up"

Done

$ sudo docker exec -it otbr sh -c "sudo ot-ctl thread start"

Done

$ sudo docker exec -it otbr sh -c "sudo ot-ctl state"

leader

Done

$ sudo docker exec -it otbr sh -c "sudo ot-ctl netdata show"

Prefixes:

fd48:5276:8095:1::/64 paos low 7400

Routes:

fd48:5276:8095:2:0:0::/96 sn low 7400

fc00::/7 sa med 7400

Services:

44970 01 24000500000e10 s 7400

44970 5d fda89b12bc80717e93014a1b555b31abd11f s 7400

Contexts:

fd48:5276:8095:1::/64 1 c

Done

$ sudo docker exec -it otbr sh -c "sudo ot-ctl ipaddr"

fda8:9b12:bc80:717e:0:ff:fe00:fc11

fd48:5276:8095:1:474b:7213:103a:3cd3

fda8:9b12:bc80:717e:0:ff:fe00:fc10

fda8:9b12:bc80:717e:0:ff:fe00:fc38

fda8:9b12:bc80:717e:0:ff:fe00:fc00

fda8:9b12:bc80:717e:0:ff:fe00:7400

fda8:9b12:bc80:717e:9301:4a1b:555b:31ab

fe80:0:0:0:4c1e:6966:69fb:e265

Done

$ sudo docker exec -it otbr sh -c "sudo service otbr-agent status"

otbr-agent is running

RESULTS

Here are the results of executing the extra commands and the status of the docker container WEB UI showing the status as well.

Now the status of the Thread Node is now reporting "leader".

$ sudo docker exec -it otbr sh -c "sudo ot-ctl state"

leader

Done

The WEB GUI showing the status and the Form menu.

All is well now I have a running OTBR running on my Ubuntu PC.

Not sure why I had to do your commands, because the Nordic documentation, states
"Form the Thread network using one of the following options:
1.Follow the instruction in the OpenThread Border Router Codelab tutorial step 3.
2.Open the http://localhost:8080/ address in a web browser and choose Form from the menu.

And I selected option 2? and the extra commands are stated in the page refered to in option 1?

This doc section at this step is very confusing. Hopefully Nordic CORRECTS this, because it was a BRAIN SYNC. I wasted a lot of time getting this to work!

RE: Guidence and Question on Running OTBR using Docker

SteveKay — Sat, 04 Nov 2023 14:49:35 GMT

Thanks for the advise , for now I will continue to try to get the OTBR docker container working for now. Stay tuned.

Steve K

RE: Guidence and Question on Running OTBR using Docker

Charlie — Fri, 03 Nov 2023 11:33:09 GMT

Hi Steve,

[quote user="SteveKay"]Can you suggest a resource to check this.[/quote]

It has been a while since I last tried as you know Matter developers mostly turn to commercial OTBRs. Installing OTBR manually (Raspberry Pi) is the tutorial I followed before.

[quote user="SteveKay"]What was your setup like on the PI?[/quote]

I tried both RPI 3 and 4 before, with nRF52840Dongle or nRF52840 DK.

The OTBR is based on a specific version of Raspbain.

You can find on this page Thread Border Router - Bidirectional IPv6 Connectivity and DNS-Based Service Discovery | OpenThread

[quote user="SteveKay"]

ON your PI what did you get return by the ot-ctl state command?

I need help in understanding why the thread node is disabled and confirm that I have a stable OpenThread network established or not. Do you know of anyone on this forum that has used the Docker image to establish an OTBR on the following hardware-software and the following instruction at the specified link?

[/quote]

Yes, I can use functional ot-ctl state commands to get the expected reply. I would suggest you refer to the above tutorial and turn to the native Raspbain-based OTBR solution. For me they are much simpler and easy to debug compared with docker ones.

Best regards,

Charlie

RE: Guidence and Question on Running OTBR using Docker

SteveKay — Wed, 01 Nov 2023 21:41:16 GMT

Hi Charlie

Thanks so much for your response. I to tried to play with the Raspberry Pi OTBR using the docs here on Nordic and on the OpenThrread docs. First I was unable to get the ot-ctl command to work but I had the wrong nRF device ffor the RCP firmware to work. Then I received the nRF52840 Dongle and decided to install the Ubuntu 64 bit os on my Raspberry PI4. but it was too slow. Then I decided to try the Google Docker implementation as described.

I'm a novice user of Ubuntu,Docker,and ODBR, But I should be able to follow the docs and get a Openthread network to be operational.

[quote userid="93921" url="~/f/nordic-q-a/105138/guidence-and-question-on-running-otbr-using-docker/453037"] would suggest you check the RCP connection first and make sure it is an available device for the docker system.[/quote]

Can you suggest a resource to check this.

[quote userid="93921" url="~/f/nordic-q-a/105138/guidence-and-question-on-running-otbr-using-docker/453037"]If you just want to try some Matter devices, I suggest you turn to commercial OTBRs provided by Smart Home ecosystem from Apple, Google, Amazon and so on. They are more stable and simple to use with related ecosystems.[/quote]

Unfortunaly I do not have access to these items.

[quote userid="118202" url="~/f/nordic-q-a/105138/guidence-and-question-on-running-otbr-using-docker"]I am using my laptop
PC IntelRegistered CoreTm i3-2330M CPU @ 2.20GHz × 4 running
Nordic nRF52840 Dongle (USB transport firmware)
Ubuntu 20.04.2 LTS[/quote]

What was your setup like on the PI?

[quote userid="118202" url="~/f/nordic-q-a/105138/guidence-and-question-on-running-otbr-using-docker"]

owever, when I get to step 11, the last step which is to check the status of the Thread node running inside the Docker, it returns DISABLED.

Step 11. Check the status of the Thread node running inside the Docker:
sudo docker exec -it otbr sh -c "sudo ot-ctl state"

[/quote]

ON your PI what did you get return by the ot-ctl state command?

Thanks and looking forward to your response

Steve K

RE: Guidence and Question on Running OTBR using Docker

Charlie — Mon, 30 Oct 2023 12:46:06 GMT

Hi Stephen,

I only played with Raspbery Pi based OTBR solution before. Not sure why RCP is disabled on this setup. I would suggest you check the RCP connection first and make sure it is an available device for the docker system.

If you just want to try some Matter devices, I suggest you turn to commercial OTBRs provided by Smart Home ecosystem from Apple, Google, Amazon and so on. They are more stable and simple to use with related ecosystems.

Best regards,

Charlie