I have a question about nPM1100 ERR, CHG pin.

RE: I have a question about nPM1100 ERR, CHG pin.

Jared — Thu, 18 Apr 2024 08:07:48 GMT

Ok, so it works now?

regards

Jared

RE: I have a question about nPM1100 ERR, CHG pin.

ozoz05 — Wed, 17 Apr 2024 23:04:00 GMT

When I received the err and chg pins as gpio, I connected the pull-up resistor and it worked normally.
Thank you.

RE: I have a question about nPM1100 ERR, CHG pin.

Jared — Fri, 12 Apr 2024 13:35:18 GMT

Hi,

Do you know if that battery has a PCM inside?

Your first design looks correct, I can't see anything that would cause it to not charge.

How many devices do you see this issue on?

regards
Jared

RE: I have a question about nPM1100 ERR, CHG pin.

ozoz05 — Thu, 11 Apr 2024 07:35:13 GMT

제품 모델은 ZM186501P-2600입니다.

RE: I have a question about nPM1100 ERR, CHG pin.

Jared — Thu, 11 Apr 2024 07:33:11 GMT

Hi,

Can you share the datasheet of the batteries that you've tried?

regards

Jared

RE: I have a question about nPM1100 ERR, CHG pin.

ozoz05 — Thu, 11 Apr 2024 01:57:52 GMT

Hello.
I tried different types of Li-ion batteries and Li-Po batteries, but they all had charging errors.
Is there a solution to this??

VTERM and ISET pin are both HIGH, could this be a problem?

When I connected D+, D- to recognize USB, it worked normally when charging Li-ion.

RE: I have a question about nPM1100 ERR, CHG pin.

Jared — Wed, 03 Apr 2024 12:33:29 GMT

Hi,

VTERM should not be configured dynamically, it should either be set high or low depending on what level you want the termination voltage to be at.

ERR pin should be connected to a pullup at the MCU side if you connect it to a host.

I suspect that you are observing one of these erratas, can you try the workaround suggested and see if it fixes your issue?

[7] Charger: CHARGER gets stuck with no VBAT capacitor

[8] Charger: CHARGER gets stuck for certain types of PCM

Edit, I see that you have the 1 µ capacitor, try the suggested workaround in errata 8.

regards

Jared

RE: I have a question about nPM1100 ERR, CHG pin.

ozoz05 — Thu, 28 Mar 2024 05:29:27 GMT

Hello.
CHG, When ERR pin is connected to GPIO, should I apply PULL UP resistor, and connect Vterm pin to GND??
3v - 4.7K

RE: I have a question about nPM1100 ERR, CHG pin.

ozoz05 — Wed, 27 Mar 2024 23:23:47 GMT

Hello.
The second configuration works normally without any problems.
The problem is that the first configuration does not charge.
The first configuration is when the limit set method is fixed 500mA.

RE: I have a question about nPM1100 ERR, CHG pin.

Jared — Wed, 27 Mar 2024 14:25:50 GMT

Hi,

[quote user=""]

After removing the USB part and changing the circuit as shown above, the input is that the CHG is disabled and charging is not possible as the ERR is activated. However, when I plugged in the charging cable and read the battery level, it seems to be charging.

[/quote]

The data signal pins for the USB peripheral needs to be in 1 of the possible configurations:

In the second configuration if D+ and D- is connected to a USB host then ISET should be grounded. It seems that you have instead routed it out? Is because you want to control the charging current externally?

[quote user=""]

Normal behavior is that ERR is disabled, and CHG should be activated/disabled when charging and discharging, but this is not the case.

[/quote]

So is it charging when you plug in the USB in the second configuration?

regards

Jared