how to enable GPIO+SPI mode on ble application

RE: how to enable GPIO+SPI mode on ble application

Simonr — Mon, 07 Oct 2024 07:20:49 GMT

Glad to hear that, then we'll close this case and you can open a new one if you have any further issues.

Best regards,

Simon

RE: how to enable GPIO+SPI mode on ble application

nk — Mon, 07 Oct 2024 01:24:00 GMT

thank you for response.

I got it. sorry, I mistook "-Dhci_rpmsg_SHIELD=nrf21540ek". I changed to "-Dipc_radio_SHIELD=nrf21540ek". I was success.

RE: how to enable GPIO+SPI mode on ble application

Hieu — Fri, 04 Oct 2024 08:03:20 GMT

Hi nk,

Susheel is out of office, and I will answer in his stead for now.

From your menuconfig screen, it seems that the shield was not set at all for the image you were exploring.

I have a few questions:

Are you browsing config for the application or the netcore?
What is the content of these compiled Kconfig file?
- <build directory>/<application name>/zephyr/.config
- <build directory>/ipc_radio/zephyr/.config
  - This is assuming you are using ipc_radio for the netcore.
    If not, please tell me what image you are running on the netcore, and let me know the .config file of that image
What was your build command?

For reference:

Here are my build outputs:

build/peripheral_uart/zephyr/.config

# CONFIG_INPUT is not set
# CONFIG_WIFI is not set
# CONFIG_MIPI_DSI is not set
# CONFIG_MODEM is not set
# CONFIG_UART_INTERRUPT_DRIVEN is not set
# CONFIG_SPI is not set
CONFIG_BT_HCI_ACL_FLOW_CONTROL=y
CONFIG_BT_HCI_VS=y
CONFIG_FLASH_LOAD_SIZE=0
CONFIG_SRAM_SIZE=448
CONFIG_FLASH_LOAD_OFFSET=0
CONFIG_MBOX_NRFX_IPC=y
CONFIG_HEAP_MEM_POOL_ADD_SIZE_BOARD=4096
# CONFIG_BT_CTLR is not set
CONFIG_NUM_IRQS=69
CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC=32768
CONFIG_FLASH_SIZE=1024
CONFIG_FLASH_BASE_ADDRESS=0x0
CONFIG_MP_MAX_NUM_CPUS=1
CONFIG_PLATFORM_SPECIFIC_INIT=y
CONFIG_SYS_CLOCK_TICKS_PER_SEC=32768
CONFIG_ROM_START_OFFSET=0
CONFIG_PINCTRL=y
CONFIG_BUILD_OUTPUT_BIN=y
CONFIG_XIP=y
CONFIG_MAIN_STACK_SIZE=1152
CONFIG_IDLE_STACK_SIZE=320
CONFIG_HAS_FLASH_LOAD_OFFSET=y
# CONFIG_SRAM_VECTOR_TABLE is not set
CONFIG_CPU_HAS_ARM_MPU=y
# CONFIG_COUNTER is not set
# CONFIG_SHARED_INTERRUPTS is not set
# CONFIG_PM_DEVICE is not set
# CONFIG_BT_STM32WBA is not set
CONFIG_TICKLESS_KERNEL=y
# CONFIG_BT_USER_PHY_UPDATE is not set
CONFIG_CLOCK_CONTROL_INIT_PRIORITY=30
# CONFIG_USE_DT_CODE_PARTITION is not set
# CONFIG_FPU is not set
CONFIG_HW_STACK_PROTECTION=y
# CONFIG_CODE_DATA_RELOCATION_SRAM is not set
CONFIG_SERIAL_INIT_PRIORITY=50
CONFIG_GPIO=y
CONFIG_SERIAL=y
# CONFIG_CPU_HAS_CUSTOM_FIXED_SOC_MPU_REGIONS is not set
CONFIG_TINYCRYPT=y
# CONFIG_MBEDTLS is not set
# CONFIG_MEMC is not set
CONFIG_KERNEL_ENTRY="__start"
# CONFIG_MULTI_LEVEL_INTERRUPTS is not set
# CONFIG_DYNAMIC_INTERRUPTS is not set
# CONFIG_CACHE is not set
CONFIG_LOG=y
# CONFIG_CODE_DATA_RELOCATION is not set
CONFIG_SYSTEM_WORKQUEUE_STACK_SIZE=2048
CONFIG_DCACHE_LINE_SIZE=32
CONFIG_GEN_IRQ_VECTOR_TABLE=y
CONFIG_SOC="nrf5340"
# CONFIG_RESET is not set
CONFIG_ARCH_SW_ISR_TABLE_ALIGN=4
CONFIG_NRF_RTC_TIMER=y
CONFIG_IPC_SERVICE_BACKEND_RPMSG_SHMEM_RESET=y
CONFIG_LOG_DOMAIN_NAME=""
CONFIG_BUILD_OUTPUT_HEX=y
CONFIG_CLOCK_CONTROL=y
CONFIG_ARCH_HAS_CUSTOM_BUSY_WAIT=y
CONFIG_SOC_HAS_TIMING_FUNCTIONS=y
# CONFIG_UART_USE_RUNTIME_CONFIGURE is not set
# CONFIG_SYSCON is not set
CONFIG_FLASH_INIT_PRIORITY=50
CONFIG_GEN_ISR_TABLES=y
CONFIG_GEN_IRQ_START_VECTOR=0
CONFIG_GEN_SW_ISR_TABLE=y
CONFIG_SRAM_OFFSET=0
# CONFIG_REBOOT is not set
# CONFIG_POWER_DOMAIN is not set
CONFIG_CONSOLE=y
CONFIG_SOC_SERIES="nrf53"
CONFIG_ARCH_IRQ_VECTOR_TABLE_ALIGN=4
CONFIG_ISR_STACK_SIZE=2048
# CONFIG_SCHED_CPU_MASK is not set
# CONFIG_WATCHDOG is not set
CONFIG_ICACHE_LINE_SIZE=32
CONFIG_PRIVILEGED_STACK_SIZE=1024

#
# Devicetree Info
#
CONFIG_DT_HAS_ARDUINO_UNO_ADC_ENABLED=y
CONFIG_DT_HAS_ARDUINO_HEADER_R3_ENABLED=y
CONFIG_DT_HAS_ARM_ARMV8M_ITM_ENABLED=y
CONFIG_DT_HAS_ARM_ARMV8M_MPU_ENABLED=y
CONFIG_DT_HAS_ARM_CORTEX_M33F_ENABLED=y
CONFIG_DT_HAS_ARM_CRYPTOCELL_312_ENABLED=y
CONFIG_DT_HAS_ARM_V8M_NVIC_ENABLED=y
CONFIG_DT_HAS_FIXED_PARTITIONS_ENABLED=y
CONFIG_DT_HAS_GPIO_KEYS_ENABLED=y
CONFIG_DT_HAS_GPIO_LEDS_ENABLED=y
CONFIG_DT_HAS_MMIO_SRAM_ENABLED=y
CONFIG_DT_HAS_NORDIC_MBOX_NRF_IPC_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_CLOCK_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_CTRLAPPERI_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_DCNF_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_DPPIC_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_EGU_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_FICR_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_GPIO_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_GPIO_FORWARDER_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_GPIOTE_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_GPREGRET_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_IEEE802154_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_IPC_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_KMU_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_MUTEX_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_OSCILLATORS_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_PINCTRL_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_POWER_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_PWM_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_QSPI_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_REGULATORS_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_RESET_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_SAADC_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_SPIM_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_SPU_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_TWIM_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_UARTE_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_UICR_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_USBD_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_USBREG_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_VMC_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_WDT_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF53_FLASH_CONTROLLER_ENABLED=y
CONFIG_DT_HAS_NORDIC_QSPI_NOR_ENABLED=y
CONFIG_DT_HAS_PWM_LEDS_ENABLED=y
CONFIG_DT_HAS_SOC_NV_FLASH_ENABLED=y
CONFIG_DT_HAS_ZEPHYR_BT_HCI_ENTROPY_ENABLED=y
CONFIG_DT_HAS_ZEPHYR_IPC_OPENAMP_STATIC_VRINGS_ENABLED=y
# end of Devicetree Info

#
# Modules
#

#
# Available modules.
#

#
# nrf (C:/ncs/v2.7.0/nrf)
#
CONFIG_MBOX=y
CONFIG_NUM_METAIRQ_PRIORITIES=0
CONFIG_LOG_BUFFER_SIZE=1024
# CONFIG_INIT_STACKS is not set
CONFIG_MPSL_WORK_STACK_SIZE=1024

#
# Nordic nRF Connect
#
CONFIG_HIDE_CHILD_PARENT_CONFIG=y
CONFIG_WARN_EXPERIMENTAL=y
CONFIG_BT_BUF_CMD_TX_COUNT=10
CONFIG_INIT_ARCH_HW_AT_BOOT=y
CONFIG_NORDIC_QSPI_NOR=y
CONFIG_NORDIC_QSPI_NOR_FLASH_LAYOUT_PAGE_SIZE=4096
# CONFIG_GETOPT is not set
# CONFIG_NCS_SAMPLES_DEFAULTS is not set
# CONFIG_NRF700X_RADIO_TEST_COMBO is not set
CONFIG_NCS_INCLUDE_RPMSG_CHILD_IMAGE=y
CONFIG_NCS_SAMPLE_HCI_IPC_CHILD_IMAGE=y

#
# Image build variants
#
# CONFIG_NCS_MCUBOOT_IN_BUILD is not set
# end of Image build variants

CONFIG_NORDIC_QSPI_NOR_STACK_WRITE_BUFFER_SIZE=4
# CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU_SPEEDUP is not set
CONFIG_BT_L2CAP_TX_MTU=65
CONFIG_BT_BUF_ACL_TX_SIZE=27
CONFIG_BT_BUF_ACL_RX_SIZE=69

#
# Subsystems
#

#
# Bootloader
#
# CONFIG_BUILD_S1_VARIANT is not set
# CONFIG_SECURE_BOOT is not set
CONFIG_PM_PARTITION_SIZE_PROVISION=0x280
# CONFIG_B0_MIN_PARTITION_SIZE is not set
CONFIG_PM_PARTITION_SIZE_B0_IMAGE=0x8000
# CONFIG_IS_SECURE_BOOTLOADER is not set

#
# Secure Boot firmware validation
#
CONFIG_SB_VALIDATION_INFO_MAGIC=0x86518483
CONFIG_SB_VALIDATION_POINTER_MAGIC=0x6919b47e
CONFIG_SB_VALIDATION_INFO_CRYPTO_ID=1
CONFIG_SB_VALIDATION_INFO_VERSION=2
CONFIG_SB_VALIDATION_METADATA_OFFSET=0
CONFIG_SB_VALIDATE_FW_SIGNATURE=y
# end of Secure Boot firmware validation

# CONFIG_SECURE_BOOT_STORAGE is not set
# end of Bootloader

#
# Bluetooth Low Energy
#
CONFIG_BT_COMPANY_ID_NORDIC=0x0059
CONFIG_BT_COMPANY_ID=0x0059
CONFIG_BT_MAX_CONN=1
CONFIG_BT_LL_SOFTDEVICE_HEADERS_INCLUDE=y
CONFIG_BT_HCI_TX_STACK_SIZE=1024
CONFIG_BT_RX_STACK_SIZE=2200

#
# BLE Libraries
#
# CONFIG_BT_GATT_POOL is not set
# CONFIG_BT_GATT_DM is not set
# CONFIG_BT_ADV_PROV is not set
# CONFIG_BT_CONN_CTX is not set

#
# Bluetooth Services
#
CONFIG_BT_NRF_SERVICES=y
# CONFIG_BT_AMS_CLIENT is not set
# CONFIG_BT_ANCS_CLIENT is not set
# CONFIG_BT_BAS_CLIENT is not set
# CONFIG_BT_BMS is not set
# CONFIG_BT_CTS_CLIENT is not set
# CONFIG_BT_DFU_SMP is not set
# CONFIG_BT_GATTP is not set
# CONFIG_BT_HIDS is not set
# CONFIG_BT_HOGP is not set
# CONFIG_BT_LBS is not set
# CONFIG_BT_NSMS is not set
CONFIG_BT_NUS=y
# CONFIG_BT_NUS_AUTHEN is not set
# CONFIG_BT_NUS_LOG_LEVEL_OFF is not set
# CONFIG_BT_NUS_LOG_LEVEL_ERR is not set
# CONFIG_BT_NUS_LOG_LEVEL_WRN is not set
# CONFIG_BT_NUS_LOG_LEVEL_INF is not set
# CONFIG_BT_NUS_LOG_LEVEL_DBG is not set
CONFIG_BT_NUS_LOG_LEVEL_DEFAULT=y
CONFIG_BT_NUS_LOG_LEVEL=3
# CONFIG_BT_NUS_CLIENT is not set
# CONFIG_BT_RSCS is not set
# CONFIG_BT_THROUGHPUT is not set
# CONFIG_BT_LATENCY is not set
# CONFIG_BT_LATENCY_CLIENT is not set
# CONFIG_BT_HRS_CLIENT is not set
# CONFIG_BT_DDFS is not set
# CONFIG_BT_MDS is not set
# CONFIG_BT_CGMS is not set
# CONFIG_BT_FAST_PAIR is not set
CONFIG_SYSTEM_WORKQUEUE_PRIORITY=-1
# CONFIG_BT_DIS is not set
CONFIG_BT_GATT_AUTO_SEC_REQ=y
# end of Bluetooth Services

#
# BLE over nRF RPC
#
# CONFIG_BT_RPC is not set
CONFIG_HEAP_MEM_POOL_SIZE=2048
CONFIG_BT_DRIVERS=y
# CONFIG_BT_RPC_STACK is not set
# CONFIG_BT_CENTRAL is not set
CONFIG_BT_PERIPHERAL=y
# CONFIG_BT_OBSERVER is not set
CONFIG_BT_BROADCASTER=y
CONFIG_BT_CONN=y
# CONFIG_BT_REMOTE_VERSION is not set
CONFIG_BT_PHY_UPDATE=y
CONFIG_BT_DATA_LEN_UPDATE=y
# CONFIG_BT_EXT_ADV is not set
# CONFIG_BT_BAS is not set
# CONFIG_BT_HRS is not set
# CONFIG_BT_TPS is not set
# CONFIG_BT_ZEPHYR_NUS is not set
# CONFIG_BT_IAS is not set
# CONFIG_BT_IAS_CLIENT is not set
# CONFIG_BT_OTS is not set
# CONFIG_BT_OTS_CLIENT is not set
CONFIG_BT_BUF_ACL_TX_COUNT=3
CONFIG_BT_BUF_ACL_RX_COUNT=6
CONFIG_BT_BUF_EVT_RX_SIZE=68
CONFIG_BT_BUF_EVT_RX_COUNT=10
CONFIG_BT_BUF_EVT_DISCARDABLE_SIZE=43
CONFIG_BT_BUF_EVT_DISCARDABLE_COUNT=3
CONFIG_BT_BUF_CMD_TX_SIZE=65
CONFIG_BT_HAS_HCI_VS=y
# CONFIG_BT_HCI_VS_FATAL_ERROR is not set
# CONFIG_BT_HCI_VS_EXT_DETECT is not set
# CONFIG_BT_WAIT_NOP is not set
CONFIG_BT_RPA=y
CONFIG_BT_ASSERT=y
CONFIG_BT_ASSERT_VERBOSE=y
# CONFIG_BT_ASSERT_PANIC is not set
CONFIG_BT_DEBUG_NONE=y
# CONFIG_BT_DEBUG_LOG is not set
# CONFIG_BT_DEBUG_MONITOR_UART is not set
# CONFIG_BT_DEBUG_MONITOR_RTT is not set
CONFIG_BT_LONG_WQ=y
CONFIG_BT_LONG_WQ_STACK_SIZE=1300
CONFIG_BT_LONG_WQ_PRIO=10
CONFIG_BT_LONG_WQ_INIT_PRIO=50
CONFIG_BT_HCI_HOST=y
# CONFIG_BT_HCI_TX_STACK_SIZE_WITH_PROMPT is not set
CONFIG_BT_HCI_TX_PRIO=7
# CONFIG_BT_RECV_WORKQ_SYS is not set
CONFIG_BT_RECV_WORKQ_BT=y
CONFIG_BT_RX_PRIO=8
CONFIG_BT_DRIVER_RX_HIGH_PRIO=6
# CONFIG_BT_AUDIO is not set
CONFIG_BT_HOST_CRYPTO=y
CONFIG_BT_HOST_CRYPTO_PRNG=y
CONFIG_BT_SETTINGS=y
CONFIG_BT_SETTINGS_CCC_LAZY_LOADING=y
CONFIG_BT_SETTINGS_DELAYED_STORE=y
CONFIG_BT_SETTINGS_DELAYED_STORE_MS=1000
CONFIG_BT_SETTINGS_CCC_STORE_ON_WRITE=y
CONFIG_BT_SETTINGS_CF_STORE_ON_WRITE=y
CONFIG_BT_SETTINGS_USE_PRINTK=y
# CONFIG_BT_FILTER_ACCEPT_LIST is not set
CONFIG_BT_LIM_ADV_TIMEOUT=30
CONFIG_BT_CONN_TX_USER_DATA_SIZE=8
CONFIG_BT_CONN_TX_MAX=3
# CONFIG_BT_CONN_PARAM_ANY is not set
CONFIG_BT_AUTO_PHY_UPDATE=y
# CONFIG_BT_USER_DATA_LEN_UPDATE is not set
CONFIG_BT_AUTO_DATA_LEN_UPDATE=y
# CONFIG_BT_REMOTE_INFO is not set
CONFIG_BT_SMP=y
# CONFIG_BT_PASSKEY_KEYPRESS is not set
# CONFIG_BT_PRIVACY is not set
# CONFIG_BT_SIGNING is not set
# CONFIG_BT_SMP_APP_PAIRING_ACCEPT is not set
# CONFIG_BT_SMP_SC_PAIR_ONLY is not set
# CONFIG_BT_SMP_SC_ONLY is not set
# CONFIG_BT_SMP_OOB_LEGACY_PAIR_ONLY is not set
# CONFIG_BT_SMP_DISABLE_LEGACY_JW_PASSKEY is not set
# CONFIG_BT_SMP_ALLOW_UNAUTH_OVERWRITE is not set
# CONFIG_BT_ID_UNPAIR_MATCHING_BONDS is not set
# CONFIG_BT_ID_ALLOW_UNAUTH_OVERWRITE is not set
# CONFIG_BT_FIXED_PASSKEY is not set
# CONFIG_BT_USE_DEBUG_KEYS is not set
CONFIG_BT_BONDABLE=y
# CONFIG_BT_BONDING_REQUIRED is not set
# CONFIG_BT_BONDABLE_PER_CONNECTION is not set
# CONFIG_BT_STORE_DEBUG_KEYS is not set
CONFIG_BT_SMP_ENFORCE_MITM=y
# CONFIG_BT_KEYS_OVERWRITE_OLDEST is not set
CONFIG_BT_SMP_MIN_ENC_KEY_SIZE=7
CONFIG_BT_L2CAP_TX_BUF_COUNT=3
CONFIG_BT_L2CAP_TX_FRAG_COUNT=2
CONFIG_BT_L2CAP_RESCHED_MS=1000
# CONFIG_BT_L2CAP_DYNAMIC_CHANNEL is not set
# CONFIG_BT_L2CAP_SEG_RECV is not set
CONFIG_BT_ATT_TX_COUNT=3
CONFIG_BT_ATT_PREPARE_COUNT=0
CONFIG_BT_ATT_RETRY_ON_SEC_ERR=y
# CONFIG_BT_ATT_SENT_CB_AFTER_TX is not set
CONFIG_BT_GATT_SERVICE_CHANGED=y
# CONFIG_BT_GATT_DYNAMIC_DB is not set
CONFIG_BT_GATT_CACHING=y
# CONFIG_BT_GATT_NOTIFY_MULTIPLE is not set
# CONFIG_BT_GATT_ENFORCE_CHANGE_UNAWARE is not set
CONFIG_BT_GATT_ENFORCE_SUBSCRIPTION=y
# CONFIG_BT_GATT_CLIENT is not set
CONFIG_BT_GATT_READ_MULTIPLE=y
CONFIG_BT_GATT_READ_MULT_VAR_LEN=y
CONFIG_BT_GAP_AUTO_UPDATE_CONN_PARAMS=y
CONFIG_BT_GAP_PERIPHERAL_PREF_PARAMS=y
CONFIG_BT_PERIPHERAL_PREF_MIN_INT=24
CONFIG_BT_PERIPHERAL_PREF_MAX_INT=40
CONFIG_BT_PERIPHERAL_PREF_LATENCY=0
CONFIG_BT_PERIPHERAL_PREF_TIMEOUT=42
# CONFIG_BT_GATT_AUTHORIZATION_CUSTOM is not set
CONFIG_BT_MAX_PAIRED=1
CONFIG_BT_CREATE_CONN_TIMEOUT=3
CONFIG_BT_CONN_PARAM_UPDATE_TIMEOUT=5000
CONFIG_BT_CONN_PARAM_RETRY_COUNT=3
CONFIG_BT_CONN_PARAM_RETRY_TIMEOUT=5000
# CONFIG_BT_DEVICE_NAME_DYNAMIC is not set
CONFIG_BT_DEVICE_NAME="Nordic_UART_Service"
# CONFIG_BT_DEVICE_APPEARANCE_DYNAMIC is not set
CONFIG_BT_DEVICE_APPEARANCE=0
CONFIG_BT_ID_MAX=1
# CONFIG_BT_DF is not set
CONFIG_BT_ECC=y
# CONFIG_BT_TINYCRYPT_ECC is not set
# CONFIG_BT_HOST_CCM is not set
# CONFIG_BT_LOG_SNIFFER_INFO is not set
# CONFIG_BT_TESTING is not set
# CONFIG_BT_CLASSIC is not set
# CONFIG_BT_HCI_VS_EVT_USER is not set
CONFIG_BT_CRYPTO=y
# end of BLE over nRF RPC
# end of Bluetooth Low Energy

#
# DFU
#
# CONFIG_DFU_MULTI_IMAGE is not set
# CONFIG_DFU_TARGET is not set
# end of DFU

# CONFIG_ESB is not set
# CONFIG_EMDS is not set

#
# Peripheral CPU DFU (PCD)
#
# CONFIG_PCD is not set
# CONFIG_PCD_APP is not set
CONFIG_PCD_VERSION_PAGE_BUF_SIZE=2046
# CONFIG_PCD_NET is not set
# end of Peripheral CPU DFU (PCD)

#
# Networking
#

#
# Application protocols
#

#
# nRF Cloud
#

#
# Client ID (nRF Cloud Device ID)
#
CONFIG_NRF_CLOUD_CLIENT_ID_SRC_COMPILE_TIME=y
CONFIG_NRF_CLOUD_CLIENT_ID="my-client-id"
# end of Client ID (nRF Cloud Device ID)

# CONFIG_NRF_CLOUD_MQTT is not set
# CONFIG_NRF_CLOUD_FOTA is not set
CONFIG_FOTA_USE_NRF_CLOUD_SETTINGS_AREA=y
CONFIG_FOTA_DL_TIMEOUT_MIN=15
# CONFIG_NRF_CLOUD_FOTA_FULL_MODEM_UPDATE is not set
# CONFIG_NRF_CLOUD_REST is not set
# CONFIG_NRF_CLOUD_LOCATION_PARSE_ANCHORS is not set
# CONFIG_NRF_CLOUD_ALERT is not set
# CONFIG_NRF_CLOUD_ALERT_LOG_LEVEL_OFF is not set
# CONFIG_NRF_CLOUD_ALERT_LOG_LEVEL_ERR is not set
# CONFIG_NRF_CLOUD_ALERT_LOG_LEVEL_WRN is not set
# CONFIG_NRF_CLOUD_ALERT_LOG_LEVEL_INF is not set
# CONFIG_NRF_CLOUD_ALERT_LOG_LEVEL_DBG is not set
CONFIG_NRF_CLOUD_ALERT_LOG_LEVEL_DEFAULT=y
CONFIG_NRF_CLOUD_ALERT_LOG_LEVEL=3
CONFIG_NRF_CLOUD_LOG_OUTPUT_LEVEL=1
# CONFIG_NRF_CLOUD_LOG_INCLUDE_LEVEL_0 is not set
CONFIG_NRF_CLOUD_LOG_BUF_SIZE=256
# CONFIG_NRF_CLOUD_LOG_LOG_LEVEL_OFF is not set
# CONFIG_NRF_CLOUD_LOG_LOG_LEVEL_ERR is not set
# CONFIG_NRF_CLOUD_LOG_LOG_LEVEL_WRN is not set
# CONFIG_NRF_CLOUD_LOG_LOG_LEVEL_INF is not set
# CONFIG_NRF_CLOUD_LOG_LOG_LEVEL_DBG is not set
CONFIG_NRF_CLOUD_LOG_LOG_LEVEL_DEFAULT=y
CONFIG_NRF_CLOUD_LOG_LOG_LEVEL=3
# CONFIG_NRF_CLOUD_COAP is not set

#
# Send shadow info sections on initial connect (MQTT/CoAP)
#
# end of Send shadow info sections on initial connect (MQTT/CoAP)

# CONFIG_NRF_CLOUD_GATEWAY is not set
# CONFIG_NRF_CLOUD_LOG_LEVEL_OFF is not set
# CONFIG_NRF_CLOUD_LOG_LEVEL_ERR is not set
# CONFIG_NRF_CLOUD_LOG_LEVEL_WRN is not set
# CONFIG_NRF_CLOUD_LOG_LEVEL_INF is not set
# CONFIG_NRF_CLOUD_LOG_LEVEL_DBG is not set
CONFIG_NRF_CLOUD_LOG_LEVEL_DEFAULT=y
CONFIG_NRF_CLOUD_LOG_LEVEL=3
# end of nRF Cloud

# CONFIG_REST_CLIENT is not set
# CONFIG_DOWNLOAD_CLIENT is not set
# CONFIG_AWS_IOT is not set
# CONFIG_AWS_JOBS is not set
# CONFIG_AZURE_IOT_HUB is not set

#
# Self-Registration (Zi ZHu Ce)
#
# end of Self-Registration (Zi ZHu Ce)

# CONFIG_ICAL_PARSER is not set
# CONFIG_FTP_CLIENT is not set
# CONFIG_LWM2M_CLIENT_UTILS is not set
# CONFIG_WIFI_CREDENTIALS is not set
# CONFIG_WIFI_CREDENTIALS_STATIC is not set
# CONFIG_MQTT_HELPER is not set
# CONFIG_NRF_PROVISIONING is not set
# CONFIG_NRF_MCUMGR_SMP_CLIENT is not set
# end of Application protocols
# end of Networking

#
# NFC
#
# CONFIG_NFC_NDEF is not set
# CONFIG_NFC_NDEF_PARSER is not set
# CONFIG_NFC_NDEF_PAYLOAD_TYPE_COMMON is not set
# CONFIG_NFC_T2T_PARSER is not set
# CONFIG_NFC_T4T_NDEF_FILE is not set
# CONFIG_NFC_T4T_ISODEP is not set
# CONFIG_NFC_T4T_APDU is not set
# CONFIG_NFC_T4T_CC_FILE is not set
# CONFIG_NFC_T4T_HL_PROCEDURE is not set
# CONFIG_NFC_PLATFORM is not set
# CONFIG_NFC_TNEP_TAG is not set
# CONFIG_NFC_TNEP_POLLER is not set
# CONFIG_NFC_TNEP_CH is not set
# end of NFC

# CONFIG_APP_EVENT_MANAGER is not set
# CONFIG_NRF_PROFILER is not set
# CONFIG_FW_INFO is not set

#
# Debug
#
# CONFIG_CPU_LOAD is not set
# CONFIG_PPI_TRACE is not set
# end of Debug

# CONFIG_SHELL_BT_NUS is not set
# CONFIG_SHELL_IPC is not set

#
# Multiprotocol service layer (MPSL)
#
# CONFIG_MPSL_FEM_ONLY is not set
# CONFIG_MPSL_FEM_DEVICE_CONFIG_254 is not set
# CONFIG_MPSL_FEM_LOG_LEVEL_OFF is not set
# CONFIG_MPSL_FEM_LOG_LEVEL_ERR is not set
# CONFIG_MPSL_FEM_LOG_LEVEL_WRN is not set
# CONFIG_MPSL_FEM_LOG_LEVEL_INF is not set
# CONFIG_MPSL_FEM_LOG_LEVEL_DBG is not set
CONFIG_MPSL_FEM_LOG_LEVEL_DEFAULT=y
CONFIG_MPSL_FEM_LOG_LEVEL=3
CONFIG_MPSL_THREAD_COOP_PRIO=8
CONFIG_MPSL_TIMESLOT_SESSION_COUNT=0
# CONFIG_MPSL_ASSERT_HANDLER is not set
CONFIG_MPSL_LOW_PRIO_IRQN=26
# CONFIG_MPSL_LOG_LEVEL_OFF is not set
# CONFIG_MPSL_LOG_LEVEL_ERR is not set
# CONFIG_MPSL_LOG_LEVEL_WRN is not set
# CONFIG_MPSL_LOG_LEVEL_INF is not set
# CONFIG_MPSL_LOG_LEVEL_DBG is not set
CONFIG_MPSL_LOG_LEVEL_DEFAULT=y
CONFIG_MPSL_LOG_LEVEL=3
# CONFIG_MPSL_PIN_DEBUG is not set
# end of Multiprotocol service layer (MPSL)

#
# Partition Manager
#
CONFIG_PARTITION_MANAGER_ENABLED=y
CONFIG_FLASH_MAP_CUSTOM=y
CONFIG_SRAM_BASE_ADDRESS=0x20000000

#
# Zephyr subsystem configurations
#
CONFIG_RPMSG_NRF53_SRAM_SIZE=0x10000
CONFIG_PM_PARTITION_SIZE_SETTINGS_STORAGE=0x2000
CONFIG_PM_PARTITION_ALIGN_SETTINGS_STORAGE=0x4000
# end of Zephyr subsystem configurations

#
# NCS subsystem configurations
#
# CONFIG_PM_SINGLE_IMAGE is not set
CONFIG_PM_EXTERNAL_FLASH_HAS_DRIVER=y
CONFIG_PM_EXTERNAL_FLASH_BASE=0
CONFIG_PM_EXTERNAL_FLASH_PATH=""
CONFIG_PM_EXTERNAL_FLASH_SIZE_BITS=0
# CONFIG_PM_OVERRIDE_EXTERNAL_DRIVER_CHECK is not set
CONFIG_PM_SRAM_BASE=0x20000000
CONFIG_PM_SRAM_SIZE=0x80000
# end of Partition Manager

#
# nRF RPC (Remote Procedure Call) library
#
# end of nRF RPC (Remote Procedure Call) library

# CONFIG_ZIGBEE is not set

#
# Full Modem Firmware Update Management(FMFU)
#
# CONFIG_MGMT_FMFU_LOG_LEVEL_OFF is not set
# CONFIG_MGMT_FMFU_LOG_LEVEL_ERR is not set
# CONFIG_MGMT_FMFU_LOG_LEVEL_WRN is not set
# CONFIG_MGMT_FMFU_LOG_LEVEL_INF is not set
# CONFIG_MGMT_FMFU_LOG_LEVEL_DBG is not set
CONFIG_MGMT_FMFU_LOG_LEVEL_DEFAULT=y
CONFIG_MGMT_FMFU_LOG_LEVEL=3
# end of Full Modem Firmware Update Management(FMFU)

#
# SUIT-based Firmware Update Management
#
CONFIG_MGMT_SUITFU_TRIGGER_UPDATE_RESET_DELAY_MS=100
CONFIG_MGMT_SUITFU_AUTO_REGISTER_HANDLERS=y
CONFIG_MGMT_SUITFU_GRP_IMG=y
CONFIG_MGMT_SUITFU_IMAGE_NUMBER=0
# CONFIG_MGMT_SUITFU_GRP_SUIT is not set
# CONFIG_MGMT_SUITFU_LOG_LEVEL_OFF is not set
# CONFIG_MGMT_SUITFU_LOG_LEVEL_ERR is not set
# CONFIG_MGMT_SUITFU_LOG_LEVEL_WRN is not set
# CONFIG_MGMT_SUITFU_LOG_LEVEL_INF is not set
# CONFIG_MGMT_SUITFU_LOG_LEVEL_DBG is not set
CONFIG_MGMT_SUITFU_LOG_LEVEL_DEFAULT=y
CONFIG_MGMT_SUITFU_LOG_LEVEL=3
# end of SUIT-based Firmware Update Management

# CONFIG_CAF is not set

#
# Nordic IEEE 802.15.4
#
# end of Nordic IEEE 802.15.4

# CONFIG_DM_MODULE is not set

#
# nRF Security
#
# CONFIG_NORDIC_SECURITY_BACKEND is not set
# CONFIG_NRF_SECURITY is not set
# CONFIG_PSA_WANT_GENERATE_RANDOM is not set
# CONFIG_PSA_WANT_ALG_CTR_DRBG is not set
# CONFIG_PSA_WANT_ALG_HMAC_DRBG is not set
# CONFIG_PSA_WANT_KEY_TYPE_DERIVE is not set
# CONFIG_PSA_WANT_KEY_TYPE_RAW_DATA is not set
# CONFIG_PSA_WANT_KEY_TYPE_HMAC is not set
# CONFIG_PSA_WANT_KEY_TYPE_PASSWORD is not set
# CONFIG_PSA_WANT_KEY_TYPE_PASSWORD_HASH is not set
# CONFIG_PSA_WANT_KEY_TYPE_PEPPER is not set
# CONFIG_PSA_WANT_KEY_TYPE_AES is not set
# CONFIG_PSA_WANT_KEY_TYPE_ARIA is not set
# CONFIG_PSA_WANT_KEY_TYPE_DES is not set
# CONFIG_PSA_WANT_KEY_TYPE_CAMELLIA is not set
# CONFIG_PSA_WANT_KEY_TYPE_SM4 is not set
# CONFIG_PSA_WANT_KEY_TYPE_ARC4 is not set
# CONFIG_PSA_WANT_KEY_TYPE_ECC_KEY_PAIR is not set
# CONFIG_PSA_WANT_KEY_TYPE_ECC_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_KEY_TYPE_ECC_KEY_PAIR_IMPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_ECC_KEY_PAIR_EXPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_ECC_KEY_PAIR_GENERATE is not set
# CONFIG_PSA_WANT_KEY_TYPE_ECC_KEY_PAIR_DERIVE is not set
# CONFIG_PSA_WANT_KEY_TYPE_RSA_KEY_PAIR is not set
# CONFIG_PSA_WANT_KEY_TYPE_RSA_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_KEY_TYPE_RSA_KEY_PAIR_IMPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_RSA_KEY_PAIR_EXPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_RSA_KEY_PAIR_GENERATE is not set
# CONFIG_PSA_WANT_KEY_TYPE_DH_KEY_PAIR is not set
# CONFIG_PSA_WANT_KEY_TYPE_DH_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_KEY_TYPE_SPAKE2P_KEY_PAIR_IMPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_SPAKE2P_KEY_PAIR_EXPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_SPAKE2P_KEY_PAIR_DERIVE is not set
# CONFIG_PSA_WANT_KEY_TYPE_SPAKE2P_KEY_PAIR is not set
# CONFIG_PSA_WANT_KEY_TYPE_SPAKE2P_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_KEY_TYPE_SRP_KEY_PAIR_IMPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_SRP_KEY_PAIR_EXPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_SRP_KEY_PAIR_DERIVE is not set
# CONFIG_PSA_WANT_KEY_TYPE_SRP_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_KEY_TYPE_SRP_KEY_PAIR is not set
# CONFIG_PSA_WANT_ALG_CCM is not set
# CONFIG_PSA_WANT_ALG_GCM is not set
# CONFIG_PSA_WANT_ALG_CHACHA20_POLY1305 is not set
# CONFIG_PSA_WANT_ALG_CBC_MAC is not set
# CONFIG_PSA_WANT_ALG_CMAC is not set
# CONFIG_PSA_WANT_ALG_HMAC is not set
# CONFIG_PSA_WANT_ALG_SHA_1 is not set
# CONFIG_PSA_WANT_ALG_SHA_224 is not set
# CONFIG_PSA_WANT_ALG_SHA_384 is not set
# CONFIG_PSA_WANT_ALG_SHA_512 is not set
# CONFIG_PSA_WANT_ALG_SHA_512_224 is not set
# CONFIG_PSA_WANT_ALG_SHA_512_256 is not set
# CONFIG_PSA_WANT_ALG_SHA3_224 is not set
# CONFIG_PSA_WANT_ALG_SHA3_256 is not set
# CONFIG_PSA_WANT_ALG_SHA3_384 is not set
# CONFIG_PSA_WANT_ALG_SHA3_512 is not set
# CONFIG_PSA_WANT_ALG_SM3 is not set
# CONFIG_PSA_WANT_ALG_SHAKE256_512 is not set
# CONFIG_PSA_WANT_ALG_RIPEMD160 is not set
# CONFIG_PSA_WANT_ALG_MD2 is not set
# CONFIG_PSA_WANT_ALG_MD4 is not set
# CONFIG_PSA_WANT_ALG_MD5 is not set
# CONFIG_PSA_WANT_ALG_ECB_NO_PADDING is not set
# CONFIG_PSA_WANT_ALG_CBC_NO_PADDING is not set
# CONFIG_PSA_WANT_ALG_CBC_PKCS7 is not set
# CONFIG_PSA_WANT_ALG_CFB is not set
# CONFIG_PSA_WANT_ALG_CTR is not set
# CONFIG_PSA_WANT_ALG_OFB is not set
# CONFIG_PSA_WANT_ALG_XTS is not set
# CONFIG_PSA_WANT_ALG_CCM_STAR_NO_TAG is not set
# CONFIG_PSA_WANT_ALG_STREAM_CIPHER is not set
# CONFIG_PSA_WANT_ALG_ECDH is not set
# CONFIG_PSA_WANT_ALG_FFDH is not set
# CONFIG_PSA_WANT_ALG_HKDF_EXTRACT is not set
# CONFIG_PSA_WANT_ALG_HKDF_EXPAND is not set
# CONFIG_PSA_WANT_ALG_ECDSA is not set
# CONFIG_PSA_WANT_ALG_ECDSA_ANY is not set
# CONFIG_PSA_WANT_ALG_DETERMINISTIC_ECDSA is not set
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_160 is not set
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_192 is not set
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_224 is not set
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_256 is not set
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_320 is not set
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_384 is not set
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_512 is not set
# CONFIG_PSA_WANT_ECC_MONTGOMERY_255 is not set
# CONFIG_PSA_WANT_ECC_MONTGOMERY_448 is not set
# CONFIG_PSA_WANT_ECC_TWISTED_EDWARDS_255 is not set
# CONFIG_PSA_WANT_ECC_TWISTED_EDWARDS_448 is not set
# CONFIG_PSA_WANT_ECC_SECP_K1_192 is not set
# CONFIG_PSA_WANT_ECC_SECP_K1_224 is not set
# CONFIG_PSA_WANT_ECC_SECP_K1_256 is not set
# CONFIG_PSA_WANT_ECC_SECP_R1_192 is not set
# CONFIG_PSA_WANT_ECC_SECP_R1_224 is not set
# CONFIG_PSA_WANT_ECC_SECP_R1_256 is not set
# CONFIG_PSA_WANT_ECC_SECP_R1_384 is not set
# CONFIG_PSA_WANT_ECC_SECP_R1_521 is not set
# CONFIG_PSA_WANT_ECC_SECP_R2_160 is not set
# CONFIG_PSA_WANT_ECC_SECT_K1_163 is not set
# CONFIG_PSA_WANT_ECC_SECT_K1_233 is not set
# CONFIG_PSA_WANT_ECC_SECT_K1_239 is not set
# CONFIG_PSA_WANT_ECC_SECT_K1_283 is not set
# CONFIG_PSA_WANT_ECC_SECT_K1_409 is not set
# CONFIG_PSA_WANT_ECC_SECT_K1_571 is not set
# CONFIG_PSA_WANT_ECC_SECT_R1_163 is not set
# CONFIG_PSA_WANT_ECC_SECT_R1_233 is not set
# CONFIG_PSA_WANT_ECC_SECT_R1_283 is not set
# CONFIG_PSA_WANT_ECC_SECT_R1_409 is not set
# CONFIG_PSA_WANT_ECC_SECT_R1_571 is not set
# CONFIG_PSA_WANT_ECC_SECT_R2_163 is not set
# CONFIG_PSA_WANT_ECC_FRP_V1_256 is not set
# CONFIG_PSA_WANT_ALG_RSA_OAEP is not set
# CONFIG_PSA_WANT_ALG_RSA_PKCS1V15_CRYPT is not set
# CONFIG_PSA_WANT_ALG_RSA_PKCS1V15_SIGN is not set
# CONFIG_PSA_WANT_ALG_RSA_PKCS1V15_SIGN_RAW is not set
# CONFIG_PSA_WANT_ALG_RSA_PSS is not set
# CONFIG_PSA_WANT_ALG_RSA_PSS_ANY_SALT is not set
# CONFIG_PSA_WANT_ALG_JPAKE is not set
# CONFIG_PSA_WANT_ALG_SPAKE2P_HMAC is not set
# CONFIG_PSA_WANT_ALG_SPAKE2P_CMAC is not set
# CONFIG_PSA_WANT_ALG_SPAKE2P_MATTER is not set
# CONFIG_PSA_WANT_ALG_SRP_6 is not set
# CONFIG_PSA_WANT_ALG_SRP_PASSWORD_HASH is not set
# CONFIG_PSA_WANT_ALG_PURE_EDDSA is not set
# CONFIG_PSA_WANT_ALG_ED25519PH is not set
# CONFIG_PSA_WANT_ALG_ED448PH is not set
# end of nRF Security

# CONFIG_NET_CORE_MONITOR is not set

#
# Audio Module
#
# CONFIG_AUDIO_MODULE_TEST is not set
CONFIG_AUDIO_MODULE_NAME_SIZE=20
# CONFIG_AUDIO_MODULE_LOG_LEVEL_OFF is not set
# CONFIG_AUDIO_MODULE_LOG_LEVEL_ERR is not set
# CONFIG_AUDIO_MODULE_LOG_LEVEL_WRN is not set
# CONFIG_AUDIO_MODULE_LOG_LEVEL_INF is not set
# CONFIG_AUDIO_MODULE_LOG_LEVEL_DBG is not set
CONFIG_AUDIO_MODULE_LOG_LEVEL_DEFAULT=y
CONFIG_AUDIO_MODULE_LOG_LEVEL=3
# end of Audio Module

# CONFIG_UART_ASYNC_ADAPTER is not set
# CONFIG_TRUSTED_STORAGE is not set

#
# SUIT provisioning
#
# CONFIG_SUIT_MPI_GENERATE is not set
# end of SUIT provisioning

# CONFIG_SUIT is not set
# CONFIG_DULT is not set
# end of Subsystems

# CONFIG_WPA_SUPP is not set
CONFIG_COMMON_LIBC_MALLOC_ARENA_SIZE=-1
CONFIG_POSIX_MAX_FDS=4
# CONFIG_WFA_QT_LOG_LEVEL_OFF is not set
# CONFIG_WFA_QT_LOG_LEVEL_ERR is not set
# CONFIG_WFA_QT_LOG_LEVEL_WRN is not set
# CONFIG_WFA_QT_LOG_LEVEL_INF is not set
# CONFIG_WFA_QT_LOG_LEVEL_DBG is not set
CONFIG_WFA_QT_LOG_LEVEL_DEFAULT=y
CONFIG_WFA_QT_LOG_LEVEL=3
# CONFIG_WFA_QT_CONTROL_APP is not set
CONFIG_WFA_QT_THREAD_STACK_SIZE=4096
CONFIG_WFA_QT_REBOOT_TIMEOUT_MS=1000
CONFIG_WFA_QT_DEFAULT_INTERFACE="nordic_wlan0"
CONFIG_WPAS_READY_TIMEOUT_MS=10000

#
# Libraries
#

#
# Binary libraries
#
# end of Binary libraries

# CONFIG_AT_MONITOR is not set
# CONFIG_LTE_LINK_CONTROL is not set
CONFIG_NRF_SPU_FLASH_REGION_SIZE=0x4000
CONFIG_FPROTECT_BLOCK_SIZE=0x4000
# CONFIG_FPROTECT is not set
# CONFIG_AT_CMD_CUSTOM is not set
CONFIG_DK_LIBRARY=y
CONFIG_DK_LIBRARY_BUTTON_SCAN_INTERVAL=10
CONFIG_DK_LIBRARY_DYNAMIC_BUTTON_HANDLERS=y
# CONFIG_DK_LIBRARY_BUTTON_NO_ISR is not set
# CONFIG_DK_LIBRARY_LOG_LEVEL_OFF is not set
# CONFIG_DK_LIBRARY_LOG_LEVEL_ERR is not set
# CONFIG_DK_LIBRARY_LOG_LEVEL_WRN is not set
# CONFIG_DK_LIBRARY_LOG_LEVEL_INF is not set
# CONFIG_DK_LIBRARY_LOG_LEVEL_DBG is not set
CONFIG_DK_LIBRARY_LOG_LEVEL_DEFAULT=y
CONFIG_DK_LIBRARY_LOG_LEVEL=3
# CONFIG_AT_CMD_PARSER is not set
# CONFIG_MODEM_INFO is not set
# CONFIG_RESET_ON_FATAL_ERROR is not set
# CONFIG_SMS is not set
# CONFIG_DATE_TIME is not set
# CONFIG_HW_ID_LIBRARY is not set
# CONFIG_RAM_POWER_DOWN_LIBRARY is not set
# CONFIG_WAVE_GEN_LIB is not set
CONFIG_HW_UNIQUE_KEY_SUPPORTED=y
CONFIG_HW_UNIQUE_KEY_PARTITION_SIZE=0
# CONFIG_MODEM_JWT is not set
# CONFIG_LOCATION is not set
# CONFIG_QOS is not set
# CONFIG_SFLOAT is not set
# CONFIG_CONTIN_ARRAY is not set
# CONFIG_PCM_MIX is not set
# CONFIG_TONE is not set
# CONFIG_PSCM is not set
# CONFIG_DATA_FIFO is not set
# CONFIG_FEM_AL_LIB is not set
# CONFIG_SAMPLE_RATE_CONVERTER is not set
CONFIG_NCS_BOOT_BANNER=y
CONFIG_NCS_APPLICATION_BOOT_BANNER_STRING="My Application"
CONFIG_NCS_NCS_BOOT_BANNER_STRING="nRF Connect SDK"
CONFIG_NCS_ZEPHYR_BOOT_BANNER_STRING="Zephyr OS"
# end of Libraries

#
# Device Drivers
#
# CONFIG_BT_DRIVER_QUIRK_NO_AUTO_DLE is not set
CONFIG_HW_CC3XX=y
# CONFIG_ETH_RTT is not set
# CONFIG_SENSOR is not set
# CONFIG_NRF_SW_LPUART is not set
CONFIG_NRFX_GPIOTE_NUM_OF_EVT_HANDLERS=1
# CONFIG_IPC_UART is not set
# CONFIG_FLASH_RPC is not set
# end of Device Drivers

#
# External libraries
#
# end of External libraries

#
# Test
#
CONFIG_ZTEST_MULTICORE_DEFAULT_SETTINGS=y
# CONFIG_UNITY is not set

#
# Mocks
#
# CONFIG_MOCK_NRF_MODEM_AT is not set
# end of Mocks
# end of Test
# end of Nordic nRF Connect

CONFIG_ZEPHYR_NRF_MODULE=y
# end of nrf (C:/ncs/v2.7.0/nrf)

#
# mcuboot (C:/ncs/v2.7.0/bootloader/mcuboot)
#

#
# MCUboot
#
CONFIG_BOOT_SIGNATURE_KEY_FILE=""
CONFIG_DT_FLASH_WRITE_BLOCK_SIZE=4
CONFIG_MCUBOOT_USB_SUPPORT=y
# CONFIG_MCUBOOT_USE_ALL_AVAILABLE_RAM is not set
# end of MCUboot

# CONFIG_XIP_SPLIT_IMAGE is not set
CONFIG_ZEPHYR_MCUBOOT_MODULE=y
# end of mcuboot (C:/ncs/v2.7.0/bootloader/mcuboot)

#
# mbedtls (C:/ncs/v2.7.0/modules/crypto/mbedtls)
#
CONFIG_ZEPHYR_MBEDTLS_MODULE=y

#
# PSA RNG support
#
# end of PSA RNG support

#
# PSA key type support
#
# end of PSA key type support

#
# PSA AEAD support
#
# end of PSA AEAD support

#
# PSA MAC support
#
# end of PSA MAC support

#
# PSA Hash support
#
# end of PSA Hash support

#
# PSA Cipher support
#
# end of PSA Cipher support

#
# PSA Key agreement support
#
# end of PSA Key agreement support

#
# PSA Key derivation support
#
# end of PSA Key derivation support

#
# PSA Asymmetric support
#

#
# Elliptic Curve type support
#
# end of Elliptic Curve type support
# end of PSA Asymmetric support
# end of mbedtls (C:/ncs/v2.7.0/modules/crypto/mbedtls)

#
# oberon-psa-crypto (C:/ncs/v2.7.0/modules/crypto/oberon-psa-crypto)
#
CONFIG_ZEPHYR_OBERON_PSA_CRYPTO_MODULE=y
# end of oberon-psa-crypto (C:/ncs/v2.7.0/modules/crypto/oberon-psa-crypto)

#
# trusted-firmware-m (C:/ncs/v2.7.0/modules/tee/tf-m/trusted-firmware-m)
#
CONFIG_TFM_BOARD="C:/ncs/v2.7.0/zephyr/modules/trusted-firmware-m/nordic/nrf5340_cpuapp"
# CONFIG_BOOTLOADER_MCUBOOT is not set
CONFIG_ZEPHYR_TRUSTED_FIRMWARE_M_MODULE=y
# end of trusted-firmware-m (C:/ncs/v2.7.0/modules/tee/tf-m/trusted-firmware-m)

CONFIG_ZEPHYR_PSA_ARCH_TESTS_MODULE=y
CONFIG_ZEPHYR_SOC_HWMV1_MODULE=y

#
# cjson (C:/ncs/v2.7.0/modules/lib/cjson)
#
# CONFIG_CJSON_LIB is not set
CONFIG_ZEPHYR_CJSON_MODULE=y
# end of cjson (C:/ncs/v2.7.0/modules/lib/cjson)

#
# azure-sdk-for-c (C:/ncs/v2.7.0/modules/lib/azure-sdk-for-c)
#
# CONFIG_AZURE_SDK is not set
CONFIG_ZEPHYR_AZURE_SDK_FOR_C_MODULE=y
# end of azure-sdk-for-c (C:/ncs/v2.7.0/modules/lib/azure-sdk-for-c)

#
# cirrus-logic (C:/ncs/v2.7.0/modules/hal/cirrus-logic)
#
# CONFIG_HW_CODEC_CIRRUS_LOGIC is not set
CONFIG_ZEPHYR_CIRRUS_LOGIC_MODULE=y
# end of cirrus-logic (C:/ncs/v2.7.0/modules/hal/cirrus-logic)

#
# openthread (C:/ncs/v2.7.0/modules/lib/openthread)
#
# CONFIG_OPENTHREAD is not set
CONFIG_ZEPHYR_OPENTHREAD_MODULE=y
# end of openthread (C:/ncs/v2.7.0/modules/lib/openthread)

#
# suit-generator (C:/ncs/v2.7.0/modules/lib/suit-generator)
#
CONFIG_SUIT_ENVELOPE_TEMPLATE=""
CONFIG_SUIT_ENVELOPE_TARGET=""
CONFIG_SUIT_ENVELOPE_OUTPUT_ARTIFACT="merged.hex"
CONFIG_SUIT_ENVELOPE_OUTPUT_MPI_MERGE=y
# CONFIG_SUIT_LOCAL_ENVELOPE_GENERATE is not set
CONFIG_ZEPHYR_SUIT_GENERATOR_MODULE=y
# end of suit-generator (C:/ncs/v2.7.0/modules/lib/suit-generator)

#
# suit-processor (C:/ncs/v2.7.0/modules/lib/suit-processor)
#
# CONFIG_SUIT_PROCESSOR is not set
CONFIG_SUIT_PLATFORM_DRY_RUN_SUPPORT=y
CONFIG_ZEPHYR_SUIT_PROCESSOR_MODULE=y
# end of suit-processor (C:/ncs/v2.7.0/modules/lib/suit-processor)

#
# memfault-firmware-sdk (C:/ncs/v2.7.0/modules/lib/memfault-firmware-sdk)
#
# CONFIG_MEMFAULT is not set
CONFIG_ZEPHYR_MEMFAULT_FIRMWARE_SDK_MODULE=y
# end of memfault-firmware-sdk (C:/ncs/v2.7.0/modules/lib/memfault-firmware-sdk)

#
# coremark (C:/ncs/v2.7.0/modules/benchmark/coremark)
#
# CONFIG_COREMARK is not set
CONFIG_ZEPHYR_COREMARK_MODULE=y
# end of coremark (C:/ncs/v2.7.0/modules/benchmark/coremark)

#
# canopennode (C:/ncs/v2.7.0/modules/lib/canopennode)
#
CONFIG_ZEPHYR_CANOPENNODE_MODULE=y
# end of canopennode (C:/ncs/v2.7.0/modules/lib/canopennode)

#
# chre (C:/ncs/v2.7.0/modules/lib/chre)
#
CONFIG_ZEPHYR_CHRE_MODULE=y
# CONFIG_CHRE is not set
# end of chre (C:/ncs/v2.7.0/modules/lib/chre)

#
# lz4 (C:/ncs/v2.7.0/modules/lib/lz4)
#
CONFIG_ZEPHYR_LZ4_MODULE=y
# CONFIG_LZ4 is not set
# end of lz4 (C:/ncs/v2.7.0/modules/lib/lz4)

#
# nanopb (C:/ncs/v2.7.0/modules/lib/nanopb)
#
CONFIG_ZEPHYR_NANOPB_MODULE=y
# CONFIG_NANOPB is not set
# end of nanopb (C:/ncs/v2.7.0/modules/lib/nanopb)

CONFIG_ZEPHYR_TF_M_TESTS_MODULE=y

#
# zscilib (C:/ncs/v2.7.0/modules/lib/zscilib)
#
# CONFIG_ZSL is not set
CONFIG_ZEPHYR_ZSCILIB_MODULE=y
# end of zscilib (C:/ncs/v2.7.0/modules/lib/zscilib)

#
# cmsis (C:/ncs/v2.7.0/modules/hal/cmsis)
#
CONFIG_ZEPHYR_CMSIS_MODULE=y
CONFIG_HAS_CMSIS_CORE=y
CONFIG_HAS_CMSIS_CORE_M=y
# CONFIG_CMSIS_M_CHECK_DEVICE_DEFINES is not set
# end of cmsis (C:/ncs/v2.7.0/modules/hal/cmsis)

#
# cmsis-dsp (C:/ncs/v2.7.0/modules/lib/cmsis-dsp)
#
CONFIG_ZEPHYR_CMSIS_DSP_MODULE=y
# CONFIG_CMSIS_DSP is not set
# end of cmsis-dsp (C:/ncs/v2.7.0/modules/lib/cmsis-dsp)

#
# cmsis-nn (C:/ncs/v2.7.0/modules/lib/cmsis-nn)
#
CONFIG_ZEPHYR_CMSIS_NN_MODULE=y
# CONFIG_CMSIS_NN is not set
# end of cmsis-nn (C:/ncs/v2.7.0/modules/lib/cmsis-nn)

#
# fatfs (C:/ncs/v2.7.0/modules/fs/fatfs)
#
CONFIG_ZEPHYR_FATFS_MODULE=y
# end of fatfs (C:/ncs/v2.7.0/modules/fs/fatfs)

#
# hal_nordic (C:/ncs/v2.7.0/modules/hal/nordic)
#
CONFIG_ZEPHYR_HAL_NORDIC_MODULE=y
CONFIG_HAS_NORDIC_DRIVERS=y

#
# Nordic drivers
#
# CONFIG_NRF_802154_SOURCE_HAL_NORDIC is not set
# CONFIG_NRF_802154_SER_HOST is not set
# end of Nordic drivers

CONFIG_HAS_NRFX=y

#
# nrfx drivers
#

#
# nrfx drivers logging
#
# CONFIG_NRFX_CLOCK_LOG is not set
# CONFIG_NRFX_DPPI_LOG is not set
# CONFIG_NRFX_GPIOTE_LOG is not set
# CONFIG_NRFX_IPC_LOG is not set
# CONFIG_NRFX_NVMC_LOG is not set
# CONFIG_NRFX_QSPI_LOG is not set
# CONFIG_NRFX_UARTE_LOG is not set
# end of nrfx drivers logging

CONFIG_NRFX_CLOCK=y
CONFIG_NRFX_CLOCK_LFXO_TWO_STAGE_ENABLED=y
# CONFIG_NRFX_COMP is not set
CONFIG_NRFX_DPPI=y
# CONFIG_NRFX_EGU0 is not set
# CONFIG_NRFX_EGU1 is not set
# CONFIG_NRFX_EGU2 is not set
# CONFIG_NRFX_EGU3 is not set
# CONFIG_NRFX_EGU4 is not set
# CONFIG_NRFX_EGU5 is not set
CONFIG_NRFX_GPIOTE=y
CONFIG_NRFX_GPIOTE0=y
# CONFIG_NRFX_GPIOTE1 is not set
# CONFIG_NRFX_I2S0 is not set
CONFIG_NRFX_IPC=y
# CONFIG_NRFX_NFCT is not set
CONFIG_NRFX_NVMC=y
# CONFIG_NRFX_PDM is not set
# CONFIG_NRFX_POWER is not set
# CONFIG_NRFX_PWM0 is not set
# CONFIG_NRFX_PWM1 is not set
# CONFIG_NRFX_PWM2 is not set
# CONFIG_NRFX_PWM3 is not set
# CONFIG_NRFX_QDEC0 is not set
# CONFIG_NRFX_QDEC1 is not set
CONFIG_NRFX_QSPI=y
# CONFIG_NRFX_RTC0 is not set
# CONFIG_NRFX_RTC1 is not set
# CONFIG_NRFX_SAADC is not set
# CONFIG_NRFX_SPIM0 is not set
# CONFIG_NRFX_SPIM1 is not set
# CONFIG_NRFX_SPIM2 is not set
# CONFIG_NRFX_SPIM3 is not set
# CONFIG_NRFX_SPIM4 is not set
# CONFIG_NRFX_SYSTICK is not set
# CONFIG_NRFX_TIMER0 is not set
# CONFIG_NRFX_TIMER1 is not set
# CONFIG_NRFX_TIMER2 is not set
# CONFIG_NRFX_TWIM0 is not set
# CONFIG_NRFX_TWIM1 is not set
# CONFIG_NRFX_TWIM2 is not set
# CONFIG_NRFX_TWIM3 is not set
CONFIG_NRFX_UARTE=y
CONFIG_NRFX_UARTE0=y
# CONFIG_NRFX_UARTE1 is not set
# CONFIG_NRFX_UARTE2 is not set
# CONFIG_NRFX_UARTE3 is not set
# CONFIG_NRFX_UARTE_CONFIG_SKIP_GPIO_CONFIG is not set
# CONFIG_NRFX_UARTE_CONFIG_SKIP_PSEL_CONFIG is not set
# CONFIG_NRFX_UARTE_CONFIG_TX_LINK is not set
# CONFIG_NRFX_UARTE_CONFIG_RX_CACHE_ENABLED is not set
# CONFIG_NRFX_USBREG is not set
# CONFIG_NRFX_WDT0 is not set
# CONFIG_NRFX_WDT1 is not set

#
# Peripheral Resource Sharing module
#
# CONFIG_NRFX_PRS_BOX_0 is not set
# CONFIG_NRFX_PRS_BOX_1 is not set
# CONFIG_NRFX_PRS_BOX_2 is not set
# CONFIG_NRFX_PRS_BOX_3 is not set
# CONFIG_NRFX_PRS_BOX_4 is not set
# end of Peripheral Resource Sharing module
# end of nrfx drivers
# end of hal_nordic (C:/ncs/v2.7.0/modules/hal/nordic)

#
# hal_st (C:/ncs/v2.7.0/modules/hal/st)
#
CONFIG_ZEPHYR_HAL_ST_MODULE=y
# end of hal_st (C:/ncs/v2.7.0/modules/hal/st)

CONFIG_ZEPHYR_HAL_WURTHELEKTRONIK_MODULE=y
CONFIG_ZEPHYR_LIBMETAL_MODULE=y

#
# liblc3 (C:/ncs/v2.7.0/modules/lib/liblc3)
#
CONFIG_ZEPHYR_LIBLC3_MODULE=y
# end of liblc3 (C:/ncs/v2.7.0/modules/lib/liblc3)

#
# littlefs (C:/ncs/v2.7.0/modules/fs/littlefs)
#
CONFIG_ZEPHYR_LITTLEFS_MODULE=y
# end of littlefs (C:/ncs/v2.7.0/modules/fs/littlefs)

#
# loramac-node (C:/ncs/v2.7.0/modules/lib/loramac-node)
#
CONFIG_ZEPHYR_LORAMAC_NODE_MODULE=y
# CONFIG_HAS_SEMTECH_RADIO_DRIVERS is not set
# end of loramac-node (C:/ncs/v2.7.0/modules/lib/loramac-node)

#
# lvgl (C:/ncs/v2.7.0/modules/lib/gui/lvgl)
#
CONFIG_ZEPHYR_LVGL_MODULE=y
# end of lvgl (C:/ncs/v2.7.0/modules/lib/gui/lvgl)

CONFIG_ZEPHYR_MIPI_SYS_T_MODULE=y
CONFIG_ZEPHYR_NRF_HW_MODELS_MODULE=y
CONFIG_ZEPHYR_OPEN_AMP_MODULE=y

#
# picolibc (C:/ncs/v2.7.0/modules/lib/picolibc)
#
# CONFIG_PICOLIBC_MODULE is not set
CONFIG_ZEPHYR_PICOLIBC_MODULE=y
# end of picolibc (C:/ncs/v2.7.0/modules/lib/picolibc)

#
# segger (C:/ncs/v2.7.0/modules/debug/segger)
#
CONFIG_ZEPHYR_SEGGER_MODULE=y
CONFIG_HAS_SEGGER_RTT=y
CONFIG_USE_SEGGER_RTT=y
CONFIG_SEGGER_RTT_CUSTOM_LOCKING=y
CONFIG_SEGGER_RTT_MAX_NUM_UP_BUFFERS=3
CONFIG_SEGGER_RTT_MAX_NUM_DOWN_BUFFERS=3
CONFIG_SEGGER_RTT_BUFFER_SIZE_UP=1024
CONFIG_SEGGER_RTT_BUFFER_SIZE_DOWN=16
CONFIG_SEGGER_RTT_PRINTF_BUFFER_SIZE=64
CONFIG_SEGGER_RTT_MODE_NO_BLOCK_SKIP=y
# CONFIG_SEGGER_RTT_MODE_NO_BLOCK_TRIM is not set
# CONFIG_SEGGER_RTT_MODE_BLOCK_IF_FIFO_FULL is not set
CONFIG_SEGGER_RTT_MODE=0
# CONFIG_SEGGER_RTT_MEMCPY_USE_BYTELOOP is not set
CONFIG_SEGGER_RTT_SECTION_NONE=y
# CONFIG_SEGGER_RTT_SECTION_DTCM is not set
# CONFIG_SEGGER_RTT_SECTION_CCM is not set
# end of segger (C:/ncs/v2.7.0/modules/debug/segger)

CONFIG_ZEPHYR_TINYCRYPT_MODULE=y

#
# uoscore-uedhoc (C:/ncs/v2.7.0/modules/lib/uoscore-uedhoc)
#
CONFIG_ZEPHYR_UOSCORE_UEDHOC_MODULE=y
# end of uoscore-uedhoc (C:/ncs/v2.7.0/modules/lib/uoscore-uedhoc)

#
# zcbor (C:/ncs/v2.7.0/modules/lib/zcbor)
#
CONFIG_ZEPHYR_ZCBOR_MODULE=y
# CONFIG_ZCBOR is not set
# end of zcbor (C:/ncs/v2.7.0/modules/lib/zcbor)

#
# nrfxlib (C:/ncs/v2.7.0/nrfxlib)
#

#
# Nordic nrfxlib
#

#
# nrf_modem (Modem library)
#
# end of nrf_modem (Modem library)

CONFIG_NRF_MODEM_SHMEM_CTRL_SIZE=0x4e8
# CONFIG_NFC_T2T_NRFXLIB is not set
# CONFIG_NFC_T4T_NRFXLIB is not set

#
# Crypto libraries for nRF5x SOCs.
#
CONFIG_NRFXLIB_CRYPTO=y
CONFIG_HAS_HW_NRF_CC3XX=y
# CONFIG_NRF_OBERON is not set
# CONFIG_NRF_CC310_BL is not set
CONFIG_NRF_CC3XX_PLATFORM=y
CONFIG_CC3XX_MUTEX_LOCK=y
# CONFIG_CC3XX_ATOMIC_LOCK is not set
# CONFIG_CC3XX_HW_MUTEX_LOCK is not set
# end of Crypto libraries for nRF5x SOCs.

# CONFIG_NRF_RPC is not set
CONFIG_NRF_802154_SOURCE_NRFXLIB=y
# CONFIG_GZLL is not set
# CONFIG_NRF_DM is not set
# CONFIG_NRF_FUEL_GAUGE is not set
# end of Nordic nrfxlib

CONFIG_ZEPHYR_NRFXLIB_MODULE=y
# end of nrfxlib (C:/ncs/v2.7.0/nrfxlib)

#
# connectedhomeip (C:/ncs/v2.7.0/modules/lib/matter)
#
# CONFIG_CHIP is not set
CONFIG_ZEPHYR_CONNECTEDHOMEIP_MODULE=y
# end of connectedhomeip (C:/ncs/v2.7.0/modules/lib/matter)

CONFIG_LIBMETAL=y
CONFIG_LIBMETAL_SRC_PATH="libmetal"
# CONFIG_LVGL is not set
# CONFIG_HAS_MEC_HAL is not set
# CONFIG_HAS_MPFS_HAL is not set
# CONFIG_HAS_MEC5_HAL is not set
CONFIG_OPENAMP=y
CONFIG_OPENAMP_SRC_PATH="open-amp"
CONFIG_OPENAMP_MASTER=y
CONFIG_OPENAMP_SLAVE=y
# CONFIG_MIPI_SYST_LIB is not set
# CONFIG_HAS_TELINK_DRIVERS is not set
# CONFIG_TINYCRYPT_CTR_PRNG is not set
CONFIG_TINYCRYPT_SHA256=y
CONFIG_TINYCRYPT_SHA256_HMAC=y
CONFIG_TINYCRYPT_SHA256_HMAC_PRNG=y
# CONFIG_TINYCRYPT_ECC_DH is not set
# CONFIG_TINYCRYPT_ECC_DSA is not set
CONFIG_TINYCRYPT_AES=y
# CONFIG_TINYCRYPT_AES_CBC is not set
# CONFIG_TINYCRYPT_AES_CTR is not set
# CONFIG_TINYCRYPT_AES_CCM is not set
CONFIG_TINYCRYPT_AES_CMAC=y
# CONFIG_MCUBOOT_BOOTUTIL_LIB is not set
# CONFIG_WIFI_NM_WPA_SUPPLICANT is not set

#
# Unavailable modules, please install those via the project manifest.
#

#
# hal_gigadevice module not available.
#

#
# Trusted-firmware-a module not available.
#

#
# THRIFT module not available.
#
# CONFIG_ACPI is not set
# end of Modules

CONFIG_BOARD="nrf5340dk"
CONFIG_BOARD_REVISION=""
CONFIG_BOARD_TARGET="nrf5340dk/nrf5340/cpuapp"
# CONFIG_NET_DRIVERS is not set
CONFIG_BOARD_NRF5340DK=y
CONFIG_BOARD_NRF5340DK_NRF5340_CPUAPP=y
CONFIG_BOARD_QUALIFIERS="nrf5340/cpuapp"

#
# Board Options
#
CONFIG_BOARD_ENABLE_DCDC_APP=y
CONFIG_BOARD_ENABLE_DCDC_NET=y
CONFIG_BOARD_ENABLE_DCDC_HV=y
CONFIG_BOARD_ENABLE_CPUNET=y
CONFIG_DOMAIN_CPUNET_BOARD="nrf5340dk/nrf5340/cpunet"
# end of Board Options

#
# Hardware Configuration
#
CONFIG_SOC_FAMILY="nordic_nrf"
CONFIG_SOC_FAMILY_NORDIC_NRF=y
CONFIG_SOC_SERIES_NRF53X=y
CONFIG_SOC_NRF5340_CPUAPP=y
CONFIG_SOC_NRF5340_CPUAPP_QKAA=y
# CONFIG_MFD is not set
# CONFIG_BUILD_OUTPUT_INFO_HEADER is not set
CONFIG_HAS_HW_NRF_CC312=y
CONFIG_HAS_HW_NRF_CLOCK=y
CONFIG_HAS_HW_NRF_CTRLAP=y
CONFIG_HAS_HW_NRF_DCNF=y
CONFIG_HAS_HW_NRF_DPPIC=y
CONFIG_HAS_HW_NRF_EGU0=y
CONFIG_HAS_HW_NRF_EGU1=y
CONFIG_HAS_HW_NRF_EGU2=y
CONFIG_HAS_HW_NRF_EGU3=y
CONFIG_HAS_HW_NRF_EGU4=y
CONFIG_HAS_HW_NRF_EGU5=y
CONFIG_HAS_HW_NRF_GPIO0=y
CONFIG_HAS_HW_NRF_GPIO1=y
CONFIG_HAS_HW_NRF_GPIOTE0=y
CONFIG_HAS_HW_NRF_IPC=y
CONFIG_HAS_HW_NRF_KMU=y
CONFIG_HAS_HW_NRF_MUTEX=y
CONFIG_HAS_HW_NRF_NVMC_PE=y
CONFIG_HAS_HW_NRF_OSCILLATORS=y
CONFIG_HAS_HW_NRF_POWER=y
CONFIG_HAS_HW_NRF_PWM0=y
CONFIG_HAS_HW_NRF_QSPI=y
CONFIG_HAS_HW_NRF_REGULATORS=y
CONFIG_HAS_HW_NRF_RESET=y
CONFIG_HAS_HW_NRF_SAADC=y
CONFIG_HAS_HW_NRF_SPIM4=y
CONFIG_HAS_HW_NRF_SPU=y
CONFIG_HAS_HW_NRF_TWIM1=y
CONFIG_HAS_HW_NRF_UARTE0=y
CONFIG_HAS_HW_NRF_USBD=y
CONFIG_HAS_HW_NRF_USBREG=y
CONFIG_HAS_HW_NRF_VMC=y
CONFIG_HAS_HW_NRF_WDT0=y
CONFIG_SOC_NRF53_ANOMALY_160_WORKAROUND_NEEDED=y
CONFIG_SOC_NRF53_ANOMALY_160_WORKAROUND=y
CONFIG_SOC_NRF53_ANOMALY_168_WORKAROUND=y
# CONFIG_SOC_NRF53_ANOMALY_168_WORKAROUND_FOR_EXECUTION_FROM_RAM is not set
CONFIG_SOC_NRF53_RTC_PRETICK=y
CONFIG_SOC_NRF53_RTC_PRETICK_IPC_CH_FROM_NET=10
CONFIG_SOC_NRF53_RTC_PRETICK_IPC_CH_TO_NET=11
CONFIG_SOC_DCDC_NRF53X_APP=y
CONFIG_SOC_DCDC_NRF53X_NET=y
CONFIG_SOC_DCDC_NRF53X_HV=y
CONFIG_NRF_SPU_FLASH_REGION_ALIGNMENT=0x4000
CONFIG_NRF_SPU_RAM_REGION_SIZE=0x2000
CONFIG_NRF_SPU_RAM_REGION_ALIGNMENT=0x2000
CONFIG_SOC_NRF_GPIO_FORWARDER_FOR_NRF5340=y
CONFIG_SOC_NRF53_CPUNET_MGMT=y
CONFIG_SOC_ENABLE_LFXO=y
# CONFIG_SOC_LFXO_CAP_EXTERNAL is not set
# CONFIG_SOC_LFXO_CAP_INT_6PF is not set
CONFIG_SOC_LFXO_CAP_INT_7PF=y
# CONFIG_SOC_LFXO_CAP_INT_9PF is not set
CONFIG_SOC_HFXO_CAP_DEFAULT=y
# CONFIG_SOC_HFXO_CAP_EXTERNAL is not set
# CONFIG_SOC_HFXO_CAP_INTERNAL is not set
CONFIG_NRF_ENABLE_CACHE=y
CONFIG_NRF53_SYNC_RTC=y
# CONFIG_SYNC_RTC_LOG_LEVEL_OFF is not set
# CONFIG_SYNC_RTC_LOG_LEVEL_ERR is not set
# CONFIG_SYNC_RTC_LOG_LEVEL_WRN is not set
# CONFIG_SYNC_RTC_LOG_LEVEL_INF is not set
# CONFIG_SYNC_RTC_LOG_LEVEL_DBG is not set
CONFIG_SYNC_RTC_LOG_LEVEL_DEFAULT=y
CONFIG_SYNC_RTC_LOG_LEVEL=3
CONFIG_NRF53_SYNC_RTC_INIT_PRIORITY=90
CONFIG_NRF_RTC_TIMER_USER_CHAN_COUNT=1
CONFIG_NRF53_SYNC_RTC_LOG_TIMESTAMP=y
CONFIG_NRF53_SYNC_RTC_IPM_OUT=7
CONFIG_NRF53_SYNC_RTC_IPM_IN=8
CONFIG_IPM_MSG_CH_8_ENABLE=y
CONFIG_IPM_MSG_CH_8_RX=y
CONFIG_NRF_SOC_SECURE_SUPPORTED=y
# CONFIG_NFCT_PINS_AS_GPIOS is not set
CONFIG_NRF_APPROTECT_USE_UICR=y
# CONFIG_NRF_APPROTECT_LOCK is not set
# CONFIG_NRF_APPROTECT_USER_HANDLING is not set
CONFIG_NRF_SECURE_APPROTECT_USE_UICR=y
# CONFIG_NRF_SECURE_APPROTECT_LOCK is not set
# CONFIG_NRF_SECURE_APPROTECT_USER_HANDLING is not set
# CONFIG_NRF_TRACE_PORT is not set
CONFIG_GPIO_INIT_PRIORITY=40
# CONFIG_SOC_LOG_LEVEL_OFF is not set
# CONFIG_SOC_LOG_LEVEL_ERR is not set
# CONFIG_SOC_LOG_LEVEL_WRN is not set
# CONFIG_SOC_LOG_LEVEL_INF is not set
# CONFIG_SOC_LOG_LEVEL_DBG is not set
CONFIG_SOC_LOG_LEVEL_DEFAULT=y
CONFIG_SOC_LOG_LEVEL=3
# end of Hardware Configuration

CONFIG_SOC_COMPATIBLE_NRF=y
CONFIG_SOC_COMPATIBLE_NRF53X=y
CONFIG_SOC_COMPATIBLE_NRF5340_CPUAPP=y
CONFIG_ARCH="arm"
CONFIG_ARCH_HAS_SINGLE_THREAD_SUPPORT=y
# CONFIG_EXTRA_EXCEPTION_INFO is not set
CONFIG_CPU_CORTEX=y
CONFIG_KOBJECT_TEXT_AREA=256
CONFIG_ARM_MPU=y
CONFIG_ARM_MPU_REGION_MIN_ALIGN_AND_SIZE=32
CONFIG_MPU_ALLOW_FLASH_WRITE=y

#
# ARM Options
#
CONFIG_ARM_ON_ENTER_CPU_IDLE_HOOK=y
CONFIG_ARM_ON_EXIT_CPU_IDLE=y
CONFIG_CPU_CORTEX_M=y
# CONFIG_ARM_ZIMAGE_HEADER is not set
CONFIG_ISA_THUMB2=y
CONFIG_ASSEMBLER_ISA_THUMB2=y
CONFIG_COMPILER_ISA_THUMB2=y
CONFIG_STACK_ALIGN_DOUBLE_WORD=y
# CONFIG_RUNTIME_NMI is not set
CONFIG_FAULT_DUMP=2
CONFIG_BUILTIN_STACK_GUARD=y
CONFIG_ARM_STACK_PROTECTION=y
CONFIG_FP16=y
CONFIG_FP16_IEEE=y
# CONFIG_FP16_ALT is not set
CONFIG_CPU_CORTEX_M33=y
CONFIG_CPU_CORTEX_M_HAS_SYSTICK=y
CONFIG_CPU_CORTEX_M_HAS_DWT=y
CONFIG_CPU_CORTEX_M_HAS_BASEPRI=y
CONFIG_CPU_CORTEX_M_HAS_VTOR=y
CONFIG_CPU_CORTEX_M_HAS_SPLIM=y
CONFIG_CPU_CORTEX_M_HAS_PROGRAMMABLE_FAULT_PRIOS=y
CONFIG_CPU_CORTEX_M_HAS_CMSE=y
CONFIG_ARMV7_M_ARMV8_M_MAINLINE=y
CONFIG_ARMV8_M_MAINLINE=y
CONFIG_ARMV8_M_SE=y
CONFIG_ARMV7_M_ARMV8_M_FP=y
CONFIG_ARMV8_M_DSP=y

#
# ARM Cortex-M0/M0+/M1/M3/M4/M7/M23/M33/M55 options
#
# CONFIG_ZERO_LATENCY_IRQS is not set
# CONFIG_SW_VECTOR_RELAY is not set
# CONFIG_CORTEX_M_DWT is not set
# CONFIG_CORTEX_M_DEBUG_MONITOR_HOOK is not set
# CONFIG_TRAP_UNALIGNED_ACCESS is not set
# end of ARM Cortex-M0/M0+/M1/M3/M4/M7/M23/M33/M55 options

CONFIG_NULL_POINTER_EXCEPTION_DETECTION_NONE=y
# CONFIG_NULL_POINTER_EXCEPTION_DETECTION_DWT is not set
# CONFIG_NULL_POINTER_EXCEPTION_DETECTION_MPU is not set
CONFIG_ARM_TRUSTZONE_M=y
# CONFIG_MPU_STACK_GUARD is not set
# CONFIG_MPU_DISABLE_BACKGROUND_MAP is not set
# CONFIG_CUSTOM_SECTION_ALIGN is not set
CONFIG_CUSTOM_SECTION_MIN_ALIGN_SIZE=32
CONFIG_CPU_HAS_NRF_IDAU=y
CONFIG_HAS_SWO=y
# end of ARM Options

CONFIG_ARM=y
CONFIG_ARCH_IS_SET=y

#
# General Architecture Options
#
# CONFIG_SEMIHOST is not set
# CONFIG_ARCH_LOG_LEVEL_OFF is not set
# CONFIG_ARCH_LOG_LEVEL_ERR is not set
# CONFIG_ARCH_LOG_LEVEL_WRN is not set
# CONFIG_ARCH_LOG_LEVEL_INF is not set
# CONFIG_ARCH_LOG_LEVEL_DBG is not set
CONFIG_ARCH_LOG_LEVEL_DEFAULT=y
CONFIG_ARCH_LOG_LEVEL=3
CONFIG_LITTLE_ENDIAN=y
# CONFIG_TRUSTED_EXECUTION_SECURE is not set
# CONFIG_TRUSTED_EXECUTION_NONSECURE is not set
# CONFIG_USERSPACE is not set
CONFIG_KOBJECT_DATA_AREA_RESERVE_EXTRA_PERCENT=100
CONFIG_KOBJECT_RODATA_AREA_EXTRA_BYTES=16
CONFIG_GEN_PRIV_STACKS=y
# CONFIG_STACK_GROWS_UP is not set

#
# Interrupt Configuration
#
CONFIG_ISR_TABLES_LOCAL_DECLARATION_SUPPORTED=y
# CONFIG_ISR_TABLES_LOCAL_DECLARATION is not set
CONFIG_IRQ_VECTOR_TABLE_JUMP_BY_ADDRESS=y
# CONFIG_IRQ_VECTOR_TABLE_JUMP_BY_CODE is not set
CONFIG_EXCEPTION_DEBUG=y
# CONFIG_SIMPLIFIED_EXCEPTION_CODES is not set
# end of Interrupt Configuration
# end of General Architecture Options

CONFIG_ARCH_HAS_TIMING_FUNCTIONS=y
CONFIG_ARCH_HAS_TRUSTED_EXECUTION=y
CONFIG_ARCH_HAS_STACK_PROTECTION=y
CONFIG_ARCH_HAS_USERSPACE=y
CONFIG_ARCH_HAS_EXECUTABLE_PAGE_BIT=y
CONFIG_ARCH_HAS_RAMFUNC_SUPPORT=y
CONFIG_ARCH_HAS_NESTED_EXCEPTION_DETECTION=y
CONFIG_ARCH_SUPPORTS_COREDUMP=y
CONFIG_ARCH_SUPPORTS_ARCH_HW_INIT=y
CONFIG_ARCH_SUPPORTS_ROM_START=y
CONFIG_ARCH_HAS_EXTRA_EXCEPTION_INFO=y
CONFIG_ARCH_HAS_THREAD_LOCAL_STORAGE=y
CONFIG_ARCH_HAS_SUSPEND_TO_RAM=y
CONFIG_ARCH_HAS_THREAD_ABORT=y
CONFIG_ARCH_HAS_CODE_DATA_RELOCATION=y
CONFIG_CPU_HAS_TEE=y
CONFIG_CPU_HAS_FPU=y
CONFIG_CPU_HAS_MPU=y
CONFIG_MPU=y
# CONFIG_MPU_LOG_LEVEL_OFF is not set
# CONFIG_MPU_LOG_LEVEL_ERR is not set
# CONFIG_MPU_LOG_LEVEL_WRN is not set
# CONFIG_MPU_LOG_LEVEL_INF is not set
# CONFIG_MPU_LOG_LEVEL_DBG is not set
CONFIG_MPU_LOG_LEVEL_DEFAULT=y
CONFIG_MPU_LOG_LEVEL=3
CONFIG_MPU_REQUIRES_NON_OVERLAPPING_REGIONS=y
CONFIG_MPU_GAP_FILLING=y
CONFIG_SRAM_REGION_PERMISSIONS=y

#
# DSP Options
#
# end of DSP Options

#
# Floating Point Options
#
# end of Floating Point Options

#
# Cache Options
#
# end of Cache Options

CONFIG_TOOLCHAIN_HAS_BUILTIN_FFS=y
# CONFIG_ARCH_CPU_IDLE_CUSTOM is not set

#
# General Kernel Options
#
# CONFIG_KERNEL_LOG_LEVEL_OFF is not set
# CONFIG_KERNEL_LOG_LEVEL_ERR is not set
# CONFIG_KERNEL_LOG_LEVEL_WRN is not set
# CONFIG_KERNEL_LOG_LEVEL_INF is not set
# CONFIG_KERNEL_LOG_LEVEL_DBG is not set
CONFIG_KERNEL_LOG_LEVEL_DEFAULT=y
CONFIG_KERNEL_LOG_LEVEL=3
CONFIG_MULTITHREADING=y
CONFIG_NUM_COOP_PRIORITIES=16
CONFIG_NUM_PREEMPT_PRIORITIES=15
CONFIG_MAIN_THREAD_PRIORITY=0
CONFIG_COOP_ENABLED=y
CONFIG_PREEMPT_ENABLED=y
CONFIG_PRIORITY_CEILING=-127
# CONFIG_SCHED_DEADLINE is not set
CONFIG_THREAD_STACK_INFO=y
# CONFIG_THREAD_CUSTOM_DATA is not set
# CONFIG_DYNAMIC_THREAD is not set
CONFIG_SCHED_DUMB=y
# CONFIG_SCHED_SCALABLE is not set
# CONFIG_SCHED_MULTIQ is not set
# CONFIG_WAITQ_SCALABLE is not set
CONFIG_WAITQ_DUMB=y

#
# Misc Kernel related options
#
CONFIG_LIBC_ERRNO=y
CONFIG_ERRNO=y
CONFIG_CURRENT_THREAD_USE_TLS=y
# end of Misc Kernel related options

#
# Kernel Debugging and Metrics
#
CONFIG_BOOT_DELAY=0
# CONFIG_THREAD_MONITOR is not set
# CONFIG_THREAD_NAME is not set
# CONFIG_THREAD_RUNTIME_STATS is not set
# end of Kernel Debugging and Metrics

# CONFIG_OBJ_CORE is not set

#
# System Work Queue Options
#
# CONFIG_SYSTEM_WORKQUEUE_NO_YIELD is not set
# end of System Work Queue Options

#
# Barrier Operations
#
CONFIG_BARRIER_OPERATIONS_ARCH=y
# end of Barrier Operations

#
# Atomic Operations
#
CONFIG_ATOMIC_OPERATIONS_BUILTIN=y
# end of Atomic Operations

#
# Timer API Options
#
CONFIG_TIMESLICING=y
CONFIG_TIMESLICE_SIZE=0
CONFIG_TIMESLICE_PRIORITY=0
# CONFIG_TIMESLICE_PER_THREAD is not set
# end of Timer API Options

#
# Other Kernel Object Options
#
CONFIG_POLL=y
# CONFIG_MEM_SLAB_TRACE_MAX_UTILIZATION is not set
CONFIG_NUM_MBOX_ASYNC_MSGS=10
# CONFIG_EVENTS is not set
# CONFIG_PIPES is not set
CONFIG_KERNEL_MEM_POOL=y
# CONFIG_HEAP_MEM_POOL_IGNORE_MIN is not set
# end of Other Kernel Object Options

CONFIG_ARCH_HAS_CUSTOM_SWAP_TO_MAIN=y
CONFIG_SWAP_NONATOMIC=y
CONFIG_SYS_CLOCK_EXISTS=y
CONFIG_TIMEOUT_64BIT=y
CONFIG_SYS_CLOCK_MAX_TIMEOUT_DAYS=365

#
# Security Options
#
# end of Security Options

#
# Memory Domains
#
CONFIG_ARCH_MEM_DOMAIN_SUPPORTS_ISOLATED_STACKS=y
CONFIG_MEM_DOMAIN_ISOLATED_STACKS=y
# end of Memory Domains

#
# SMP Options
#
CONFIG_MP_NUM_CPUS=1
# CONFIG_TICKET_SPINLOCKS is not set
# end of SMP Options

CONFIG_TOOLCHAIN_SUPPORTS_THREAD_LOCAL_STORAGE=y
CONFIG_THREAD_LOCAL_STORAGE=y
# end of General Kernel Options

#
# Device Options
#
# CONFIG_DEVICE_DEPS is not set
# CONFIG_DEVICE_MUTABLE is not set
# end of Device Options

#
# Initialization Priorities
#
CONFIG_KERNEL_INIT_PRIORITY_OBJECTS=30
CONFIG_KERNEL_INIT_PRIORITY_DEFAULT=40
CONFIG_KERNEL_INIT_PRIORITY_DEVICE=50
CONFIG_APPLICATION_INIT_PRIORITY=90
# end of Initialization Priorities

#
# Virtual Memory Support
#
# end of Virtual Memory Support

#
# Device Drivers
#
# CONFIG_ADC is not set
# CONFIG_AUDIO is not set
# CONFIG_AUXDISPLAY is not set
# CONFIG_BBRAM is not set

#
# Bluetooth HCI Driver Options
#
# CONFIG_BT_H4 is not set
# CONFIG_BT_H5 is not set
# CONFIG_BT_RPMSG is not set
CONFIG_BT_HCI_IPC=y
# CONFIG_BT_SPI is not set
# CONFIG_BT_STM32_IPM is not set
# CONFIG_BT_ESP32 is not set
# CONFIG_BT_B91 is not set
# CONFIG_BT_PSOC6_BLESS is not set
# CONFIG_BT_DA1469X is not set
# CONFIG_BT_NO_DRIVER is not set
# CONFIG_BT_AMBIQ_HCI is not set
CONFIG_BT_DRV_TX_STACK_SIZE=256
CONFIG_BT_DRV_RX_STACK_SIZE=256
# CONFIG_CAN is not set
# CONFIG_CHARGER is not set
# CONFIG_CLOCK_CONTROL_LOG_LEVEL_OFF is not set
# CONFIG_CLOCK_CONTROL_LOG_LEVEL_ERR is not set
# CONFIG_CLOCK_CONTROL_LOG_LEVEL_WRN is not set
# CONFIG_CLOCK_CONTROL_LOG_LEVEL_INF is not set
# CONFIG_CLOCK_CONTROL_LOG_LEVEL_DBG is not set
CONFIG_CLOCK_CONTROL_LOG_LEVEL_DEFAULT=y
CONFIG_CLOCK_CONTROL_LOG_LEVEL=3
CONFIG_CLOCK_CONTROL_NRF=y
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC is not set
CONFIG_CLOCK_CONTROL_NRF_K32SRC_XTAL=y
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_SYNTH is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_500PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_250PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_150PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_100PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_75PPM is not set
CONFIG_CLOCK_CONTROL_NRF_K32SRC_50PPM=y
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_30PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_20PPM is not set
CONFIG_CLOCK_CONTROL_NRF_ACCURACY=50
# CONFIG_CLOCK_CONTROL_FIXED_RATE_CLOCK is not set
CONFIG_CONSOLE_INPUT_MAX_LINE_LEN=128
CONFIG_CONSOLE_HAS_DRIVER=y
# CONFIG_CONSOLE_HANDLER is not set
CONFIG_CONSOLE_INIT_PRIORITY=60
CONFIG_UART_CONSOLE=y
# CONFIG_UART_CONSOLE_DEBUG_SERVER_HOOKS is not set
# CONFIG_UART_CONSOLE_MCUMGR is not set
# CONFIG_RAM_CONSOLE is not set
# CONFIG_RTT_CONSOLE is not set
# CONFIG_IPM_CONSOLE_SENDER is not set
# CONFIG_IPM_CONSOLE_RECEIVER is not set
# CONFIG_UART_MCUMGR is not set
# CONFIG_UART_CONSOLE_LOG_LEVEL_OFF is not set
# CONFIG_UART_CONSOLE_LOG_LEVEL_ERR is not set
# CONFIG_UART_CONSOLE_LOG_LEVEL_WRN is not set
# CONFIG_UART_CONSOLE_LOG_LEVEL_INF is not set
# CONFIG_UART_CONSOLE_LOG_LEVEL_DBG is not set
CONFIG_UART_CONSOLE_LOG_LEVEL_DEFAULT=y
CONFIG_UART_CONSOLE_LOG_LEVEL=3
# CONFIG_GSM_MUX is not set
# CONFIG_EFI_CONSOLE is not set
# CONFIG_COREDUMP_DEVICE is not set
# CONFIG_CRYPTO is not set
# CONFIG_DAC is not set
# CONFIG_DAI is not set
# CONFIG_DISK_DRIVERS is not set
# CONFIG_DISPLAY is not set
# CONFIG_DMA is not set
# CONFIG_EDAC is not set
# CONFIG_EEPROM is not set
# CONFIG_ENTROPY_GENERATOR is not set
# CONFIG_ESPI is not set
CONFIG_FLASH_HAS_DRIVER_ENABLED=y
CONFIG_FLASH_HAS_PAGE_LAYOUT=y
CONFIG_FLASH_JESD216=y
CONFIG_FLASH=y
# CONFIG_FLASH_LOG_LEVEL_OFF is not set
# CONFIG_FLASH_LOG_LEVEL_ERR is not set
# CONFIG_FLASH_LOG_LEVEL_WRN is not set
# CONFIG_FLASH_LOG_LEVEL_INF is not set
# CONFIG_FLASH_LOG_LEVEL_DBG is not set
CONFIG_FLASH_LOG_LEVEL_DEFAULT=y
CONFIG_FLASH_LOG_LEVEL=3
# CONFIG_FLASH_JESD216_API is not set
CONFIG_FLASH_PAGE_LAYOUT=y
CONFIG_SOC_FLASH_NRF=y
CONFIG_SOC_FLASH_NRF_RADIO_SYNC_NONE=y
# CONFIG_SOC_FLASH_NRF_PARTIAL_ERASE is not set
# CONFIG_SOC_FLASH_NRF_UICR is not set
# CONFIG_SOC_FLASH_NRF_EMULATE_ONE_BYTE_WRITE_ACCESS is not set
CONFIG_NORDIC_QSPI_NOR_INIT_PRIORITY=41
# CONFIG_NORDIC_QSPI_NOR_XIP is not set
CONFIG_NORDIC_QSPI_NOR_TIMEOUT_MS=500
# CONFIG_FPGA is not set
# CONFIG_FUEL_GAUGE is not set
# CONFIG_GNSS is not set
# CONFIG_GPIO_LOG_LEVEL_OFF is not set
# CONFIG_GPIO_LOG_LEVEL_ERR is not set
# CONFIG_GPIO_LOG_LEVEL_WRN is not set
# CONFIG_GPIO_LOG_LEVEL_INF is not set
# CONFIG_GPIO_LOG_LEVEL_DBG is not set
CONFIG_GPIO_LOG_LEVEL_DEFAULT=y
CONFIG_GPIO_LOG_LEVEL=3
# CONFIG_GPIO_GET_DIRECTION is not set
# CONFIG_GPIO_GET_CONFIG is not set
# CONFIG_GPIO_HOGS is not set
# CONFIG_GPIO_ENABLE_DISABLE_INTERRUPT is not set
CONFIG_GPIO_NRFX=y
CONFIG_GPIO_NRFX_INTERRUPT=y
# CONFIG_HWINFO is not set
# CONFIG_HWSPINLOCK is not set
# CONFIG_I2C is not set
# CONFIG_I2S is not set
# CONFIG_I3C is not set

#
# Interrupt controller drivers
#
CONFIG_INTC_INIT_PRIORITY=40
# CONFIG_INTC_LOG_LEVEL_OFF is not set
# CONFIG_INTC_LOG_LEVEL_ERR is not set
# CONFIG_INTC_LOG_LEVEL_WRN is not set
# CONFIG_INTC_LOG_LEVEL_INF is not set
# CONFIG_INTC_LOG_LEVEL_DBG is not set
CONFIG_INTC_LOG_LEVEL_DEFAULT=y
CONFIG_INTC_LOG_LEVEL=3
# CONFIG_INTC_ESP32 is not set
# end of Interrupt controller drivers

# CONFIG_IPM is not set
# CONFIG_KSCAN is not set
# CONFIG_LED is not set
# CONFIG_LED_STRIP is not set
# CONFIG_LORA is not set
CONFIG_MBOX_INIT_PRIORITY=40
# CONFIG_MBOX_LOG_LEVEL_OFF is not set
# CONFIG_MBOX_LOG_LEVEL_ERR is not set
# CONFIG_MBOX_LOG_LEVEL_WRN is not set
# CONFIG_MBOX_LOG_LEVEL_INF is not set
# CONFIG_MBOX_LOG_LEVEL_DBG is not set
CONFIG_MBOX_LOG_LEVEL_DEFAULT=y
CONFIG_MBOX_LOG_LEVEL=3
# CONFIG_MDIO is not set
# CONFIG_MIPI_DBI is not set

#
# Miscellaneous Drivers
#
# CONFIG_TIMEAWARE_GPIO is not set
# end of Miscellaneous Drivers

# CONFIG_MM_DRV is not set
# CONFIG_PCIE is not set
# CONFIG_PCIE_ENDPOINT is not set
# CONFIG_PECI is not set
# CONFIG_PINCTRL_LOG_LEVEL_OFF is not set
# CONFIG_PINCTRL_LOG_LEVEL_ERR is not set
# CONFIG_PINCTRL_LOG_LEVEL_WRN is not set
# CONFIG_PINCTRL_LOG_LEVEL_INF is not set
# CONFIG_PINCTRL_LOG_LEVEL_DBG is not set
CONFIG_PINCTRL_LOG_LEVEL_DEFAULT=y
CONFIG_PINCTRL_LOG_LEVEL=3
CONFIG_PINCTRL_STORE_REG=y
# CONFIG_PINCTRL_DYNAMIC is not set
CONFIG_PINCTRL_NRF=y
# CONFIG_PM_CPU_OPS is not set
# CONFIG_PS2 is not set
# CONFIG_PTP_CLOCK is not set
# CONFIG_PWM is not set
# CONFIG_REGULATOR is not set
# CONFIG_RETAINED_MEM is not set
# CONFIG_RTC is not set
# CONFIG_SDHC is not set

#
# Capabilities
#
CONFIG_SERIAL_HAS_DRIVER=y
CONFIG_SERIAL_SUPPORT_ASYNC=y
CONFIG_SERIAL_SUPPORT_INTERRUPT=y
# CONFIG_UART_LOG_LEVEL_OFF is not set
# CONFIG_UART_LOG_LEVEL_ERR is not set
# CONFIG_UART_LOG_LEVEL_WRN is not set
# CONFIG_UART_LOG_LEVEL_INF is not set
# CONFIG_UART_LOG_LEVEL_DBG is not set
CONFIG_UART_LOG_LEVEL_DEFAULT=y
CONFIG_UART_LOG_LEVEL=3
CONFIG_UART_ASYNC_API=y
# CONFIG_UART_LINE_CTRL is not set
# CONFIG_UART_DRV_CMD is not set
# CONFIG_UART_WIDE_DATA is not set
# CONFIG_UART_PIPE is not set
# CONFIG_UART_ASYNC_RX_HELPER is not set

#
# Serial Drivers
#
CONFIG_UART_NRFX=y
CONFIG_UART_NRFX_UARTE=y
CONFIG_UART_NRFX_UARTE_LEGACY_SHIM=y
CONFIG_UART_ASYNC_TX_CACHE_SIZE=8
CONFIG_UART_0_ASYNC=y
CONFIG_UART_0_ENHANCED_POLL_OUT=y
# CONFIG_UART_0_NRF_PARITY_BIT is not set
CONFIG_UART_0_NRF_TX_BUFFER_SIZE=32
# CONFIG_UART_0_NRF_HW_ASYNC is not set
# CONFIG_UART_0_NRF_ASYNC_LOW_POWER is not set
# CONFIG_SMBUS is not set

#
# Timer drivers
#
# CONFIG_TIMER_READS_ITS_FREQUENCY_AT_RUNTIME is not set
# CONFIG_SYSTEM_CLOCK_SLOPPY_IDLE is not set
CONFIG_SYSTEM_CLOCK_INIT_PRIORITY=0
CONFIG_TICKLESS_CAPABLE=y
CONFIG_SYSTEM_TIMER_HAS_DISABLE_SUPPORT=y
# CONFIG_NRF_RTC_TIMER_TRIGGER_OVERFLOW is not set
# CONFIG_SYSTEM_CLOCK_NO_WAIT is not set
# CONFIG_SYSTEM_CLOCK_WAIT_FOR_AVAILABILITY is not set
CONFIG_SYSTEM_CLOCK_WAIT_FOR_STABILITY=y
# end of Timer drivers

# CONFIG_USB_BC12 is not set
# CONFIG_UDC_DRIVER is not set
# CONFIG_UHC_DRIVER is not set
# CONFIG_UVB is not set
# CONFIG_USB_DEVICE_DRIVER is not set
# CONFIG_NRF_USBD_COMMON_LOG_LEVEL_OFF is not set
# CONFIG_NRF_USBD_COMMON_LOG_LEVEL_ERR is not set
# CONFIG_NRF_USBD_COMMON_LOG_LEVEL_WRN is not set
# CONFIG_NRF_USBD_COMMON_LOG_LEVEL_INF is not set
# CONFIG_NRF_USBD_COMMON_LOG_LEVEL_DBG is not set
CONFIG_NRF_USBD_COMMON_LOG_LEVEL_DEFAULT=y
CONFIG_NRF_USBD_COMMON_LOG_LEVEL=3
# CONFIG_NRF_USBD_COMMON is not set
# CONFIG_USBC_TCPC_DRIVER is not set
# CONFIG_USBC_LOG_LEVEL_OFF is not set
# CONFIG_USBC_LOG_LEVEL_ERR is not set
# CONFIG_USBC_LOG_LEVEL_WRN is not set
# CONFIG_USBC_LOG_LEVEL_INF is not set
# CONFIG_USBC_LOG_LEVEL_DBG is not set
CONFIG_USBC_LOG_LEVEL_DEFAULT=y
CONFIG_USBC_LOG_LEVEL=3
# CONFIG_USBC_VBUS_DRIVER is not set
# CONFIG_USBC_PPC_DRIVER is not set
# CONFIG_VIDEO is not set
# CONFIG_VIRTUALIZATION is not set
# CONFIG_W1 is not set
# end of Device Drivers

# CONFIG_REQUIRES_FULL_LIBC is not set
# CONFIG_REQUIRES_FLOAT_PRINTF is not set
CONFIG_FULL_LIBC_SUPPORTED=y
CONFIG_MINIMAL_LIBC_SUPPORTED=y
CONFIG_NEWLIB_LIBC_SUPPORTED=y
CONFIG_PICOLIBC_SUPPORTED=y

#
# C Library
#
# CONFIG_MINIMAL_LIBC is not set
CONFIG_PICOLIBC=y
# CONFIG_NEWLIB_LIBC is not set
# CONFIG_EXTERNAL_LIBC is not set
CONFIG_HAS_NEWLIB_LIBC_NANO=y
CONFIG_COMMON_LIBC_ABORT=y
CONFIG_COMMON_LIBC_MALLOC=y
CONFIG_COMMON_LIBC_CALLOC=y
CONFIG_COMMON_LIBC_REALLOCARRAY=y
# CONFIG_PICOLIBC_USE_MODULE is not set
CONFIG_PICOLIBC_USE_TOOLCHAIN=y
CONFIG_PICOLIBC_HEAP_SIZE=-2
# CONFIG_PICOLIBC_IO_FLOAT is not set
CONFIG_PICOLIBC_IO_LONG_LONG=y
CONFIG_STDOUT_CONSOLE=y
CONFIG_NEED_LIBC_MEM_PARTITION=y
# end of C Library

#
# C++ Language Support
#
# CONFIG_CPP is not set

#
# Deprecated
#
# CONFIG_CPLUSPLUS is not set
# CONFIG_LIB_CPLUSPLUS is not set
# end of Deprecated
# end of C++ Language Support

CONFIG_CRC=y

#
# Additional libraries
#

#
# Hash Function Support
#
# CONFIG_SYS_HASH_FUNC32 is not set
# end of Hash Function Support

#
# Hashmap (Hash Table) Support
#
# CONFIG_SYS_HASH_MAP is not set
# end of Hashmap (Hash Table) Support

#
# Heap and Memory Allocation
#
# CONFIG_SYS_HEAP_VALIDATE is not set
# CONFIG_SYS_HEAP_STRESS is not set
# CONFIG_SYS_HEAP_INFO is not set
CONFIG_SYS_HEAP_ALLOC_LOOPS=3
# CONFIG_SYS_HEAP_RUNTIME_STATS is not set
# CONFIG_SYS_HEAP_LISTENER is not set
# CONFIG_SYS_HEAP_SMALL_ONLY is not set
# CONFIG_SYS_HEAP_BIG_ONLY is not set
CONFIG_SYS_HEAP_AUTO=y
# CONFIG_MULTI_HEAP is not set
# CONFIG_SHARED_MULTI_HEAP is not set
# end of Heap and Memory Allocation

#
# Memory Blocks
#
# CONFIG_SYS_MEM_BLOCKS is not set
# end of Memory Blocks

#
# OS Support Library
#
# CONFIG_FDTABLE is not set
# CONFIG_PRINTK_SYNC is not set
CONFIG_MPSC_PBUF=y
# CONFIG_SPSC_PBUF is not set
# CONFIG_MPSC_CLEAR_ALLOCATED is not set
CONFIG_HAS_POWEROFF=y
# CONFIG_POWEROFF is not set
CONFIG_CBPRINTF_COMPLETE=y
# CONFIG_CBPRINTF_NANO is not set
CONFIG_CBPRINTF_FULL_INTEGRAL=y
# CONFIG_CBPRINTF_REDUCED_INTEGRAL is not set
# CONFIG_CBPRINTF_FP_SUPPORT is not set
# CONFIG_CBPRINTF_FP_A_SUPPORT is not set
# CONFIG_CBPRINTF_LIBC_SUBSTS is not set
# CONFIG_CBPRINTF_PACKAGE_LOG_LEVEL_OFF is not set
# CONFIG_CBPRINTF_PACKAGE_LOG_LEVEL_ERR is not set
# CONFIG_CBPRINTF_PACKAGE_LOG_LEVEL_WRN is not set
# CONFIG_CBPRINTF_PACKAGE_LOG_LEVEL_INF is not set
# CONFIG_CBPRINTF_PACKAGE_LOG_LEVEL_DBG is not set
CONFIG_CBPRINTF_PACKAGE_LOG_LEVEL_DEFAULT=y
CONFIG_CBPRINTF_PACKAGE_LOG_LEVEL=3
# CONFIG_CBPRINTF_PACKAGE_LONGDOUBLE is not set
# CONFIG_CBPRINTF_STATIC_PACKAGE_CHECK_ALIGNMENT is not set
CONFIG_CBPRINTF_CONVERT_CHECK_PTR=y
# end of OS Support Library

#
# POSIX API Support
#

#
# POSIX Options
#
# CONFIG_POSIX_API is not set
# CONFIG_POSIX_ASYNCHRONOUS_IO is not set
# CONFIG_POSIX_CLOCK is not set
# CONFIG_POSIX_CONFSTR is not set
# CONFIG_POSIX_ENV is not set
# CONFIG_POSIX_ENV_LOG_LEVEL_OFF is not set
# CONFIG_POSIX_ENV_LOG_LEVEL_ERR is not set
# CONFIG_POSIX_ENV_LOG_LEVEL_WRN is not set
# CONFIG_POSIX_ENV_LOG_LEVEL_INF is not set
# CONFIG_POSIX_ENV_LOG_LEVEL_DBG is not set
CONFIG_POSIX_ENV_LOG_LEVEL_DEFAULT=y
CONFIG_POSIX_ENV_LOG_LEVEL=3
# CONFIG_EVENTFD is not set

#
# File descriptor table options
#
# end of File descriptor table options

# CONFIG_FNMATCH is not set
# CONFIG_POSIX_MQUEUE is not set

#
# sem_t support
#
CONFIG_SEM_VALUE_MAX=32767
CONFIG_SEM_NAMELEN_MAX=16
# end of sem_t support

#
# Signal support
#
CONFIG_POSIX_RTSIG_MAX=0
# CONFIG_POSIX_SIGNAL is not set
# end of Signal support

# CONFIG_POSIX_PUTMSG is not set

#
# Sysconf support
#
# CONFIG_POSIX_SYSCONF is not set
CONFIG_POSIX_PAGE_SIZE_BITS=6
# end of Sysconf support

# CONFIG_POSIX_SYSLOG is not set
# CONFIG_TIMER is not set
# CONFIG_POSIX_UNAME is not set
# end of POSIX Options

#
# POSIX Shell Utilities
#
# end of POSIX Shell Utilities
# end of POSIX API Support

# CONFIG_OPENAMP_RSC_TABLE is not set
# CONFIG_SMF is not set
CONFIG_LIBGCC_RTLIB=y

#
# Utility Library
#
# CONFIG_JSON_LIBRARY is not set
# CONFIG_RING_BUFFER is not set
CONFIG_NOTIFY=y
# CONFIG_BASE64 is not set
CONFIG_ONOFF=y
# CONFIG_WINSTREAM is not set
# CONFIG_UTF8 is not set
# end of Utility Library
# end of Additional libraries

#
# Subsystems and OS Services
#
# CONFIG_BINDESC is not set
CONFIG_BT=y
CONFIG_BT_HCI=y
# CONFIG_BT_CUSTOM is not set
# CONFIG_BT_HCI_RAW is not set
# CONFIG_BT_HCI_RAW_H4 is not set
# CONFIG_BT_HCI_RAW_CMD_EXT is not set
CONFIG_BT_CONN_TX=y
# CONFIG_BT_SCA_UPDATE is not set
# CONFIG_BT_TRANSMIT_POWER_CONTROL is not set
# CONFIG_BT_ISO_PERIPHERAL is not set
# CONFIG_BT_ISO_CENTRAL is not set
# CONFIG_BT_ISO_BROADCASTER is not set
# CONFIG_BT_ISO_SYNC_RECEIVER is not set

#
# Bluetooth buffer configuration
#
# end of Bluetooth buffer configuration

#
# Bluetooth Host
#

#
# L2CAP Options
#
# end of L2CAP Options

#
# ATT and GATT Options
#
# end of ATT and GATT Options

#
# GATT Services
#
# end of GATT Services

#
# Bluetooth Classic Options
#
# end of Bluetooth Classic Options
# end of Bluetooth Host

# CONFIG_BT_CTLR_DEBUG_PINS_CPUAPP is not set
# CONFIG_BT_SHELL is not set
# CONFIG_BT_EAD is not set
CONFIG_BT_LOG=y

#
# Bluetooth logging
#
# CONFIG_BT_LOG_LEVEL_OFF is not set
# CONFIG_BT_LOG_LEVEL_ERR is not set
# CONFIG_BT_LOG_LEVEL_WRN is not set
# CONFIG_BT_LOG_LEVEL_INF is not set
# CONFIG_BT_LOG_LEVEL_DBG is not set
CONFIG_BT_LOG_LEVEL_DEFAULT=y
CONFIG_BT_LOG_LEVEL=3
CONFIG_BT_HCI_DRIVER_LOG_LEVEL_INHERIT=y
CONFIG_BT_HCI_DRIVER_LOG_LEVEL=3
# CONFIG_BT_HCI_DRIVER_LOG_LEVEL_OFF is not set
# CONFIG_BT_HCI_DRIVER_LOG_LEVEL_ERR is not set
# CONFIG_BT_HCI_DRIVER_LOG_LEVEL_WRN is not set
# CONFIG_BT_HCI_DRIVER_LOG_LEVEL_INF is not set
# CONFIG_BT_HCI_DRIVER_LOG_LEVEL_DBG is not set
# CONFIG_BT_HCI_DRIVER_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_RPA_LOG_LEVEL_INHERIT=y
CONFIG_BT_RPA_LOG_LEVEL=3
# CONFIG_BT_RPA_LOG_LEVEL_OFF is not set
# CONFIG_BT_RPA_LOG_LEVEL_ERR is not set
# CONFIG_BT_RPA_LOG_LEVEL_WRN is not set
# CONFIG_BT_RPA_LOG_LEVEL_INF is not set
# CONFIG_BT_RPA_LOG_LEVEL_DBG is not set
# CONFIG_BT_RPA_LOG_LEVEL_DEFAULT is not set

#
# Audio
#
CONFIG_BT_AICS_LOG_LEVEL_INHERIT=y
CONFIG_BT_AICS_LOG_LEVEL=3
# CONFIG_BT_AICS_LOG_LEVEL_OFF is not set
# CONFIG_BT_AICS_LOG_LEVEL_ERR is not set
# CONFIG_BT_AICS_LOG_LEVEL_WRN is not set
# CONFIG_BT_AICS_LOG_LEVEL_INF is not set
# CONFIG_BT_AICS_LOG_LEVEL_DBG is not set
# CONFIG_BT_AICS_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_AICS_CLIENT_LOG_LEVEL_INHERIT=y
CONFIG_BT_AICS_CLIENT_LOG_LEVEL=3
# CONFIG_BT_AICS_CLIENT_LOG_LEVEL_OFF is not set
# CONFIG_BT_AICS_CLIENT_LOG_LEVEL_ERR is not set
# CONFIG_BT_AICS_CLIENT_LOG_LEVEL_WRN is not set
# CONFIG_BT_AICS_CLIENT_LOG_LEVEL_INF is not set
# CONFIG_BT_AICS_CLIENT_LOG_LEVEL_DBG is not set
# CONFIG_BT_AICS_CLIENT_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_BAP_STREAM_LOG_LEVEL_INHERIT=y
CONFIG_BT_BAP_STREAM_LOG_LEVEL=3
# CONFIG_BT_BAP_STREAM_LOG_LEVEL_OFF is not set
# CONFIG_BT_BAP_STREAM_LOG_LEVEL_ERR is not set
# CONFIG_BT_BAP_STREAM_LOG_LEVEL_WRN is not set
# CONFIG_BT_BAP_STREAM_LOG_LEVEL_INF is not set
# CONFIG_BT_BAP_STREAM_LOG_LEVEL_DBG is not set
# CONFIG_BT_BAP_STREAM_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_BAP_BASE_LOG_LEVEL_INHERIT=y
CONFIG_BT_BAP_BASE_LOG_LEVEL=3
# CONFIG_BT_BAP_BASE_LOG_LEVEL_OFF is not set
# CONFIG_BT_BAP_BASE_LOG_LEVEL_ERR is not set
# CONFIG_BT_BAP_BASE_LOG_LEVEL_WRN is not set
# CONFIG_BT_BAP_BASE_LOG_LEVEL_INF is not set
# CONFIG_BT_BAP_BASE_LOG_LEVEL_DBG is not set
# CONFIG_BT_BAP_BASE_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_AUDIO_CODEC_LOG_LEVEL_INHERIT=y
CONFIG_BT_AUDIO_CODEC_LOG_LEVEL=3
# CONFIG_BT_AUDIO_CODEC_LOG_LEVEL_OFF is not set
# CONFIG_BT_AUDIO_CODEC_LOG_LEVEL_ERR is not set
# CONFIG_BT_AUDIO_CODEC_LOG_LEVEL_WRN is not set
# CONFIG_BT_AUDIO_CODEC_LOG_LEVEL_INF is not set
# CONFIG_BT_AUDIO_CODEC_LOG_LEVEL_DBG is not set
# CONFIG_BT_AUDIO_CODEC_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_ASCS_LOG_LEVEL_INHERIT=y
CONFIG_BT_ASCS_LOG_LEVEL=3
# CONFIG_BT_ASCS_LOG_LEVEL_OFF is not set
# CONFIG_BT_ASCS_LOG_LEVEL_ERR is not set
# CONFIG_BT_ASCS_LOG_LEVEL_WRN is not set
# CONFIG_BT_ASCS_LOG_LEVEL_INF is not set
# CONFIG_BT_ASCS_LOG_LEVEL_DBG is not set
# CONFIG_BT_ASCS_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_BAP_UNICAST_SERVER_LOG_LEVEL_INHERIT=y
CONFIG_BT_BAP_UNICAST_SERVER_LOG_LEVEL=3
# CONFIG_BT_BAP_UNICAST_SERVER_LOG_LEVEL_OFF is not set
# CONFIG_BT_BAP_UNICAST_SERVER_LOG_LEVEL_ERR is not set
# CONFIG_BT_BAP_UNICAST_SERVER_LOG_LEVEL_WRN is not set
# CONFIG_BT_BAP_UNICAST_SERVER_LOG_LEVEL_INF is not set
# CONFIG_BT_BAP_UNICAST_SERVER_LOG_LEVEL_DBG is not set
# CONFIG_BT_BAP_UNICAST_SERVER_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_BAP_UNICAST_CLIENT_LOG_LEVEL_INHERIT=y
CONFIG_BT_BAP_UNICAST_CLIENT_LOG_LEVEL=3
# CONFIG_BT_BAP_UNICAST_CLIENT_LOG_LEVEL_OFF is not set
# CONFIG_BT_BAP_UNICAST_CLIENT_LOG_LEVEL_ERR is not set
# CONFIG_BT_BAP_UNICAST_CLIENT_LOG_LEVEL_WRN is not set
# CONFIG_BT_BAP_UNICAST_CLIENT_LOG_LEVEL_INF is not set
# CONFIG_BT_BAP_UNICAST_CLIENT_LOG_LEVEL_DBG is not set
# CONFIG_BT_BAP_UNICAST_CLIENT_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_BAP_BROADCAST_SOURCE_LOG_LEVEL_INHERIT=y
CONFIG_BT_BAP_BROADCAST_SOURCE_LOG_LEVEL=3
# CONFIG_BT_BAP_BROADCAST_SOURCE_LOG_LEVEL_OFF is not set
# CONFIG_BT_BAP_BROADCAST_SOURCE_LOG_LEVEL_ERR is not set
# CONFIG_BT_BAP_BROADCAST_SOURCE_LOG_LEVEL_WRN is not set
# CONFIG_BT_BAP_BROADCAST_SOURCE_LOG_LEVEL_INF is not set
# CONFIG_BT_BAP_BROADCAST_SOURCE_LOG_LEVEL_DBG is not set
# CONFIG_BT_BAP_BROADCAST_SOURCE_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_BAP_BROADCAST_SINK_LOG_LEVEL_INHERIT=y
CONFIG_BT_BAP_BROADCAST_SINK_LOG_LEVEL=3
# CONFIG_BT_BAP_BROADCAST_SINK_LOG_LEVEL_OFF is not set
# CONFIG_BT_BAP_BROADCAST_SINK_LOG_LEVEL_ERR is not set
# CONFIG_BT_BAP_BROADCAST_SINK_LOG_LEVEL_WRN is not set
# CONFIG_BT_BAP_BROADCAST_SINK_LOG_LEVEL_INF is not set
# CONFIG_BT_BAP_BROADCAST_SINK_LOG_LEVEL_DBG is not set
# CONFIG_BT_BAP_BROADCAST_SINK_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_BAP_SCAN_DELEGATOR_LOG_LEVEL_INHERIT=y
CONFIG_BT_BAP_SCAN_DELEGATOR_LOG_LEVEL=3
# CONFIG_BT_BAP_SCAN_DELEGATOR_LOG_LEVEL_OFF is not set
# CONFIG_BT_BAP_SCAN_DELEGATOR_LOG_LEVEL_ERR is not set
# CONFIG_BT_BAP_SCAN_DELEGATOR_LOG_LEVEL_WRN is not set
# CONFIG_BT_BAP_SCAN_DELEGATOR_LOG_LEVEL_INF is not set
# CONFIG_BT_BAP_SCAN_DELEGATOR_LOG_LEVEL_DBG is not set
# CONFIG_BT_BAP_SCAN_DELEGATOR_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_BAP_BROADCAST_ASSISTANT_LOG_LEVEL_INHERIT=y
CONFIG_BT_BAP_BROADCAST_ASSISTANT_LOG_LEVEL=3
# CONFIG_BT_BAP_BROADCAST_ASSISTANT_LOG_LEVEL_OFF is not set
# CONFIG_BT_BAP_BROADCAST_ASSISTANT_LOG_LEVEL_ERR is not set
# CONFIG_BT_BAP_BROADCAST_ASSISTANT_LOG_LEVEL_WRN is not set
# CONFIG_BT_BAP_BROADCAST_ASSISTANT_LOG_LEVEL_INF is not set
# CONFIG_BT_BAP_BROADCAST_ASSISTANT_LOG_LEVEL_DBG is not set
# CONFIG_BT_BAP_BROADCAST_ASSISTANT_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_BAP_ISO_LOG_LEVEL_INHERIT=y
CONFIG_BT_BAP_ISO_LOG_LEVEL=3
# CONFIG_BT_BAP_ISO_LOG_LEVEL_OFF is not set
# CONFIG_BT_BAP_ISO_LOG_LEVEL_ERR is not set
# CONFIG_BT_BAP_ISO_LOG_LEVEL_WRN is not set
# CONFIG_BT_BAP_ISO_LOG_LEVEL_INF is not set
# CONFIG_BT_BAP_ISO_LOG_LEVEL_DBG is not set
# CONFIG_BT_BAP_ISO_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_CAP_ACCEPTOR_LOG_LEVEL_INHERIT=y
CONFIG_BT_CAP_ACCEPTOR_LOG_LEVEL=3
# CONFIG_BT_CAP_ACCEPTOR_LOG_LEVEL_OFF is not set
# CONFIG_BT_CAP_ACCEPTOR_LOG_LEVEL_ERR is not set
# CONFIG_BT_CAP_ACCEPTOR_LOG_LEVEL_WRN is not set
# CONFIG_BT_CAP_ACCEPTOR_LOG_LEVEL_INF is not set
# CONFIG_BT_CAP_ACCEPTOR_LOG_LEVEL_DBG is not set
# CONFIG_BT_CAP_ACCEPTOR_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_CAP_INITIATOR_LOG_LEVEL_INHERIT=y
CONFIG_BT_CAP_INITIATOR_LOG_LEVEL=3
# CONFIG_BT_CAP_INITIATOR_LOG_LEVEL_OFF is not set
# CONFIG_BT_CAP_INITIATOR_LOG_LEVEL_ERR is not set
# CONFIG_BT_CAP_INITIATOR_LOG_LEVEL_WRN is not set
# CONFIG_BT_CAP_INITIATOR_LOG_LEVEL_INF is not set
# CONFIG_BT_CAP_INITIATOR_LOG_LEVEL_DBG is not set
# CONFIG_BT_CAP_INITIATOR_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_CAP_COMMANDER_LOG_LEVEL_INHERIT=y
CONFIG_BT_CAP_COMMANDER_LOG_LEVEL=3
# CONFIG_BT_CAP_COMMANDER_LOG_LEVEL_OFF is not set
# CONFIG_BT_CAP_COMMANDER_LOG_LEVEL_ERR is not set
# CONFIG_BT_CAP_COMMANDER_LOG_LEVEL_WRN is not set
# CONFIG_BT_CAP_COMMANDER_LOG_LEVEL_INF is not set
# CONFIG_BT_CAP_COMMANDER_LOG_LEVEL_DBG is not set
# CONFIG_BT_CAP_COMMANDER_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_CAP_COMMON_LOG_LEVEL_INHERIT=y
CONFIG_BT_CAP_COMMON_LOG_LEVEL=3
# CONFIG_BT_CAP_COMMON_LOG_LEVEL_OFF is not set
# CONFIG_BT_CAP_COMMON_LOG_LEVEL_ERR is not set
# CONFIG_BT_CAP_COMMON_LOG_LEVEL_WRN is not set
# CONFIG_BT_CAP_COMMON_LOG_LEVEL_INF is not set
# CONFIG_BT_CAP_COMMON_LOG_LEVEL_DBG is not set
# CONFIG_BT_CAP_COMMON_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_CAP_STREAM_LOG_LEVEL_INHERIT=y
CONFIG_BT_CAP_STREAM_LOG_LEVEL=3
# CONFIG_BT_CAP_STREAM_LOG_LEVEL_OFF is not set
# CONFIG_BT_CAP_STREAM_LOG_LEVEL_ERR is not set
# CONFIG_BT_CAP_STREAM_LOG_LEVEL_WRN is not set
# CONFIG_BT_CAP_STREAM_LOG_LEVEL_INF is not set
# CONFIG_BT_CAP_STREAM_LOG_LEVEL_DBG is not set
# CONFIG_BT_CAP_STREAM_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_CSIP_SET_MEMBER_LOG_LEVEL_INHERIT=y
CONFIG_BT_CSIP_SET_MEMBER_LOG_LEVEL=3
# CONFIG_BT_CSIP_SET_MEMBER_LOG_LEVEL_OFF is not set
# CONFIG_BT_CSIP_SET_MEMBER_LOG_LEVEL_ERR is not set
# CONFIG_BT_CSIP_SET_MEMBER_LOG_LEVEL_WRN is not set
# CONFIG_BT_CSIP_SET_MEMBER_LOG_LEVEL_INF is not set
# CONFIG_BT_CSIP_SET_MEMBER_LOG_LEVEL_DBG is not set
# CONFIG_BT_CSIP_SET_MEMBER_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_CSIP_SET_COORDINATOR_LOG_LEVEL_INHERIT=y
CONFIG_BT_CSIP_SET_COORDINATOR_LOG_LEVEL=3
# CONFIG_BT_CSIP_SET_COORDINATOR_LOG_LEVEL_OFF is not set
# CONFIG_BT_CSIP_SET_COORDINATOR_LOG_LEVEL_ERR is not set
# CONFIG_BT_CSIP_SET_COORDINATOR_LOG_LEVEL_WRN is not set
# CONFIG_BT_CSIP_SET_COORDINATOR_LOG_LEVEL_INF is not set
# CONFIG_BT_CSIP_SET_COORDINATOR_LOG_LEVEL_DBG is not set
# CONFIG_BT_CSIP_SET_COORDINATOR_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_CSIP_SET_MEMBER_CRYPTO_LOG_LEVEL_INHERIT=y
CONFIG_BT_CSIP_SET_MEMBER_CRYPTO_LOG_LEVEL=3
# CONFIG_BT_CSIP_SET_MEMBER_CRYPTO_LOG_LEVEL_OFF is not set
# CONFIG_BT_CSIP_SET_MEMBER_CRYPTO_LOG_LEVEL_ERR is not set
# CONFIG_BT_CSIP_SET_MEMBER_CRYPTO_LOG_LEVEL_WRN is not set
# CONFIG_BT_CSIP_SET_MEMBER_CRYPTO_LOG_LEVEL_INF is not set
# CONFIG_BT_CSIP_SET_MEMBER_CRYPTO_LOG_LEVEL_DBG is not set
# CONFIG_BT_CSIP_SET_MEMBER_CRYPTO_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_HAS_LOG_LEVEL_INHERIT=y
CONFIG_BT_HAS_LOG_LEVEL=3
# CONFIG_BT_HAS_LOG_LEVEL_OFF is not set
# CONFIG_BT_HAS_LOG_LEVEL_ERR is not set
# CONFIG_BT_HAS_LOG_LEVEL_WRN is not set
# CONFIG_BT_HAS_LOG_LEVEL_INF is not set
# CONFIG_BT_HAS_LOG_LEVEL_DBG is not set
# CONFIG_BT_HAS_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_HAS_CLIENT_LOG_LEVEL_INHERIT=y
CONFIG_BT_HAS_CLIENT_LOG_LEVEL=3
# CONFIG_BT_HAS_CLIENT_LOG_LEVEL_OFF is not set
# CONFIG_BT_HAS_CLIENT_LOG_LEVEL_ERR is not set
# CONFIG_BT_HAS_CLIENT_LOG_LEVEL_WRN is not set
# CONFIG_BT_HAS_CLIENT_LOG_LEVEL_INF is not set
# CONFIG_BT_HAS_CLIENT_LOG_LEVEL_DBG is not set
# CONFIG_BT_HAS_CLIENT_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MCS_LOG_LEVEL_INHERIT=y
CONFIG_BT_MCS_LOG_LEVEL=3
# CONFIG_BT_MCS_LOG_LEVEL_OFF is not set
# CONFIG_BT_MCS_LOG_LEVEL_ERR is not set
# CONFIG_BT_MCS_LOG_LEVEL_WRN is not set
# CONFIG_BT_MCS_LOG_LEVEL_INF is not set
# CONFIG_BT_MCS_LOG_LEVEL_DBG is not set
# CONFIG_BT_MCS_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MCC_LOG_LEVEL_INHERIT=y
CONFIG_BT_MCC_LOG_LEVEL=3
# CONFIG_BT_MCC_LOG_LEVEL_OFF is not set
# CONFIG_BT_MCC_LOG_LEVEL_ERR is not set
# CONFIG_BT_MCC_LOG_LEVEL_WRN is not set
# CONFIG_BT_MCC_LOG_LEVEL_INF is not set
# CONFIG_BT_MCC_LOG_LEVEL_DBG is not set
# CONFIG_BT_MCC_LOG_LEVEL_DEFAULT is not set
CONFIG_MCTL_LOG_LEVEL_INHERIT=y
CONFIG_MCTL_LOG_LEVEL=3
# CONFIG_MCTL_LOG_LEVEL_OFF is not set
# CONFIG_MCTL_LOG_LEVEL_ERR is not set
# CONFIG_MCTL_LOG_LEVEL_WRN is not set
# CONFIG_MCTL_LOG_LEVEL_INF is not set
# CONFIG_MCTL_LOG_LEVEL_DBG is not set
# CONFIG_MCTL_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MICP_MIC_DEV_LOG_LEVEL_INHERIT=y
CONFIG_BT_MICP_MIC_DEV_LOG_LEVEL=3
# CONFIG_BT_MICP_MIC_DEV_LOG_LEVEL_OFF is not set
# CONFIG_BT_MICP_MIC_DEV_LOG_LEVEL_ERR is not set
# CONFIG_BT_MICP_MIC_DEV_LOG_LEVEL_WRN is not set
# CONFIG_BT_MICP_MIC_DEV_LOG_LEVEL_INF is not set
# CONFIG_BT_MICP_MIC_DEV_LOG_LEVEL_DBG is not set
# CONFIG_BT_MICP_MIC_DEV_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MICP_MIC_CTLR_LOG_LEVEL_INHERIT=y
CONFIG_BT_MICP_MIC_CTLR_LOG_LEVEL=3
# CONFIG_BT_MICP_MIC_CTLR_LOG_LEVEL_OFF is not set
# CONFIG_BT_MICP_MIC_CTLR_LOG_LEVEL_ERR is not set
# CONFIG_BT_MICP_MIC_CTLR_LOG_LEVEL_WRN is not set
# CONFIG_BT_MICP_MIC_CTLR_LOG_LEVEL_INF is not set
# CONFIG_BT_MICP_MIC_CTLR_LOG_LEVEL_DBG is not set
# CONFIG_BT_MICP_MIC_CTLR_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MPL_LOG_LEVEL_INHERIT=y
CONFIG_BT_MPL_LOG_LEVEL=3
# CONFIG_BT_MPL_LOG_LEVEL_OFF is not set
# CONFIG_BT_MPL_LOG_LEVEL_ERR is not set
# CONFIG_BT_MPL_LOG_LEVEL_WRN is not set
# CONFIG_BT_MPL_LOG_LEVEL_INF is not set
# CONFIG_BT_MPL_LOG_LEVEL_DBG is not set
# CONFIG_BT_MPL_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_PACS_LOG_LEVEL_INHERIT=y
CONFIG_BT_PACS_LOG_LEVEL=3
# CONFIG_BT_PACS_LOG_LEVEL_OFF is not set
# CONFIG_BT_PACS_LOG_LEVEL_ERR is not set
# CONFIG_BT_PACS_LOG_LEVEL_WRN is not set
# CONFIG_BT_PACS_LOG_LEVEL_INF is not set
# CONFIG_BT_PACS_LOG_LEVEL_DBG is not set
# CONFIG_BT_PACS_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_TBS_LOG_LEVEL_INHERIT=y
CONFIG_BT_TBS_LOG_LEVEL=3
# CONFIG_BT_TBS_LOG_LEVEL_OFF is not set
# CONFIG_BT_TBS_LOG_LEVEL_ERR is not set
# CONFIG_BT_TBS_LOG_LEVEL_WRN is not set
# CONFIG_BT_TBS_LOG_LEVEL_INF is not set
# CONFIG_BT_TBS_LOG_LEVEL_DBG is not set
# CONFIG_BT_TBS_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_TBS_CLIENT_LOG_LEVEL_INHERIT=y
CONFIG_BT_TBS_CLIENT_LOG_LEVEL=3
# CONFIG_BT_TBS_CLIENT_LOG_LEVEL_OFF is not set
# CONFIG_BT_TBS_CLIENT_LOG_LEVEL_ERR is not set
# CONFIG_BT_TBS_CLIENT_LOG_LEVEL_WRN is not set
# CONFIG_BT_TBS_CLIENT_LOG_LEVEL_INF is not set
# CONFIG_BT_TBS_CLIENT_LOG_LEVEL_DBG is not set
# CONFIG_BT_TBS_CLIENT_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_VCP_VOL_REND_LOG_LEVEL_INHERIT=y
CONFIG_BT_VCP_VOL_REND_LOG_LEVEL=3
# CONFIG_BT_VCP_VOL_REND_LOG_LEVEL_OFF is not set
# CONFIG_BT_VCP_VOL_REND_LOG_LEVEL_ERR is not set
# CONFIG_BT_VCP_VOL_REND_LOG_LEVEL_WRN is not set
# CONFIG_BT_VCP_VOL_REND_LOG_LEVEL_INF is not set
# CONFIG_BT_VCP_VOL_REND_LOG_LEVEL_DBG is not set
# CONFIG_BT_VCP_VOL_REND_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_VCP_VOL_CTLR_LOG_LEVEL_INHERIT=y
CONFIG_BT_VCP_VOL_CTLR_LOG_LEVEL=3
# CONFIG_BT_VCP_VOL_CTLR_LOG_LEVEL_OFF is not set
# CONFIG_BT_VCP_VOL_CTLR_LOG_LEVEL_ERR is not set
# CONFIG_BT_VCP_VOL_CTLR_LOG_LEVEL_WRN is not set
# CONFIG_BT_VCP_VOL_CTLR_LOG_LEVEL_INF is not set
# CONFIG_BT_VCP_VOL_CTLR_LOG_LEVEL_DBG is not set
# CONFIG_BT_VCP_VOL_CTLR_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_VOCS_LOG_LEVEL_INHERIT=y
CONFIG_BT_VOCS_LOG_LEVEL=3
# CONFIG_BT_VOCS_LOG_LEVEL_OFF is not set
# CONFIG_BT_VOCS_LOG_LEVEL_ERR is not set
# CONFIG_BT_VOCS_LOG_LEVEL_WRN is not set
# CONFIG_BT_VOCS_LOG_LEVEL_INF is not set
# CONFIG_BT_VOCS_LOG_LEVEL_DBG is not set
# CONFIG_BT_VOCS_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_VOCS_CLIENT_LOG_LEVEL_INHERIT=y
CONFIG_BT_VOCS_CLIENT_LOG_LEVEL=3
# CONFIG_BT_VOCS_CLIENT_LOG_LEVEL_OFF is not set
# CONFIG_BT_VOCS_CLIENT_LOG_LEVEL_ERR is not set
# CONFIG_BT_VOCS_CLIENT_LOG_LEVEL_WRN is not set
# CONFIG_BT_VOCS_CLIENT_LOG_LEVEL_INF is not set
# CONFIG_BT_VOCS_CLIENT_LOG_LEVEL_DBG is not set
# CONFIG_BT_VOCS_CLIENT_LOG_LEVEL_DEFAULT is not set
# CONFIG_BT_PBP_LOG_LEVEL_OFF is not set
# CONFIG_BT_PBP_LOG_LEVEL_ERR is not set
# CONFIG_BT_PBP_LOG_LEVEL_WRN is not set
# CONFIG_BT_PBP_LOG_LEVEL_INF is not set
# CONFIG_BT_PBP_LOG_LEVEL_DBG is not set
CONFIG_BT_PBP_LOG_LEVEL_DEFAULT=y
CONFIG_BT_PBP_LOG_LEVEL=3
# end of Audio

#
# Others
#
CONFIG_BT_CRYPTO_LOG_LEVEL_INHERIT=y
CONFIG_BT_CRYPTO_LOG_LEVEL=3
# CONFIG_BT_CRYPTO_LOG_LEVEL_OFF is not set
# CONFIG_BT_CRYPTO_LOG_LEVEL_ERR is not set
# CONFIG_BT_CRYPTO_LOG_LEVEL_WRN is not set
# CONFIG_BT_CRYPTO_LOG_LEVEL_INF is not set
# CONFIG_BT_CRYPTO_LOG_LEVEL_DBG is not set
# CONFIG_BT_CRYPTO_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_ATT_LOG_LEVEL_INHERIT=y
CONFIG_BT_ATT_LOG_LEVEL=3
# CONFIG_BT_ATT_LOG_LEVEL_OFF is not set
# CONFIG_BT_ATT_LOG_LEVEL_ERR is not set
# CONFIG_BT_ATT_LOG_LEVEL_WRN is not set
# CONFIG_BT_ATT_LOG_LEVEL_INF is not set
# CONFIG_BT_ATT_LOG_LEVEL_DBG is not set
# CONFIG_BT_ATT_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_GATT_LOG_LEVEL_INHERIT=y
CONFIG_BT_GATT_LOG_LEVEL=3
# CONFIG_BT_GATT_LOG_LEVEL_OFF is not set
# CONFIG_BT_GATT_LOG_LEVEL_ERR is not set
# CONFIG_BT_GATT_LOG_LEVEL_WRN is not set
# CONFIG_BT_GATT_LOG_LEVEL_INF is not set
# CONFIG_BT_GATT_LOG_LEVEL_DBG is not set
# CONFIG_BT_GATT_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_L2CAP_LOG_LEVEL_INHERIT=y
CONFIG_BT_L2CAP_LOG_LEVEL=3
# CONFIG_BT_L2CAP_LOG_LEVEL_OFF is not set
# CONFIG_BT_L2CAP_LOG_LEVEL_ERR is not set
# CONFIG_BT_L2CAP_LOG_LEVEL_WRN is not set
# CONFIG_BT_L2CAP_LOG_LEVEL_INF is not set
# CONFIG_BT_L2CAP_LOG_LEVEL_DBG is not set
# CONFIG_BT_L2CAP_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_EAD_LOG_LEVEL_INHERIT=y
CONFIG_BT_EAD_LOG_LEVEL=3
# CONFIG_BT_EAD_LOG_LEVEL_OFF is not set
# CONFIG_BT_EAD_LOG_LEVEL_ERR is not set
# CONFIG_BT_EAD_LOG_LEVEL_WRN is not set
# CONFIG_BT_EAD_LOG_LEVEL_INF is not set
# CONFIG_BT_EAD_LOG_LEVEL_DBG is not set
# CONFIG_BT_EAD_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_DF_LOG_LEVEL_INHERIT=y
CONFIG_BT_DF_LOG_LEVEL=3
# CONFIG_BT_DF_LOG_LEVEL_OFF is not set
# CONFIG_BT_DF_LOG_LEVEL_ERR is not set
# CONFIG_BT_DF_LOG_LEVEL_WRN is not set
# CONFIG_BT_DF_LOG_LEVEL_INF is not set
# CONFIG_BT_DF_LOG_LEVEL_DBG is not set
# CONFIG_BT_DF_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_SETTINGS_LOG_LEVEL_INHERIT=y
CONFIG_BT_SETTINGS_LOG_LEVEL=3
# CONFIG_BT_SETTINGS_LOG_LEVEL_OFF is not set
# CONFIG_BT_SETTINGS_LOG_LEVEL_ERR is not set
# CONFIG_BT_SETTINGS_LOG_LEVEL_WRN is not set
# CONFIG_BT_SETTINGS_LOG_LEVEL_INF is not set
# CONFIG_BT_SETTINGS_LOG_LEVEL_DBG is not set
# CONFIG_BT_SETTINGS_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_HCI_CORE_LOG_LEVEL_INHERIT=y
CONFIG_BT_HCI_CORE_LOG_LEVEL=3
# CONFIG_BT_HCI_CORE_LOG_LEVEL_OFF is not set
# CONFIG_BT_HCI_CORE_LOG_LEVEL_ERR is not set
# CONFIG_BT_HCI_CORE_LOG_LEVEL_WRN is not set
# CONFIG_BT_HCI_CORE_LOG_LEVEL_INF is not set
# CONFIG_BT_HCI_CORE_LOG_LEVEL_DBG is not set
# CONFIG_BT_HCI_CORE_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_CONN_LOG_LEVEL_INHERIT=y
CONFIG_BT_CONN_LOG_LEVEL=3
# CONFIG_BT_CONN_LOG_LEVEL_OFF is not set
# CONFIG_BT_CONN_LOG_LEVEL_ERR is not set
# CONFIG_BT_CONN_LOG_LEVEL_WRN is not set
# CONFIG_BT_CONN_LOG_LEVEL_INF is not set
# CONFIG_BT_CONN_LOG_LEVEL_DBG is not set
# CONFIG_BT_CONN_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_ISO_LOG_LEVEL_INHERIT=y
CONFIG_BT_ISO_LOG_LEVEL=3
# CONFIG_BT_ISO_LOG_LEVEL_OFF is not set
# CONFIG_BT_ISO_LOG_LEVEL_ERR is not set
# CONFIG_BT_ISO_LOG_LEVEL_WRN is not set
# CONFIG_BT_ISO_LOG_LEVEL_INF is not set
# CONFIG_BT_ISO_LOG_LEVEL_DBG is not set
# CONFIG_BT_ISO_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_KEYS_LOG_LEVEL_INHERIT=y
CONFIG_BT_KEYS_LOG_LEVEL=3
# CONFIG_BT_KEYS_LOG_LEVEL_OFF is not set
# CONFIG_BT_KEYS_LOG_LEVEL_ERR is not set
# CONFIG_BT_KEYS_LOG_LEVEL_WRN is not set
# CONFIG_BT_KEYS_LOG_LEVEL_INF is not set
# CONFIG_BT_KEYS_LOG_LEVEL_DBG is not set
# CONFIG_BT_KEYS_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_SMP_LOG_LEVEL_INHERIT=y
CONFIG_BT_SMP_LOG_LEVEL=3
# CONFIG_BT_SMP_LOG_LEVEL_OFF is not set
# CONFIG_BT_SMP_LOG_LEVEL_ERR is not set
# CONFIG_BT_SMP_LOG_LEVEL_WRN is not set
# CONFIG_BT_SMP_LOG_LEVEL_INF is not set
# CONFIG_BT_SMP_LOG_LEVEL_DBG is not set
# CONFIG_BT_SMP_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_SERVICE_LOG_LEVEL_INHERIT=y
CONFIG_BT_SERVICE_LOG_LEVEL=3
# CONFIG_BT_SERVICE_LOG_LEVEL_OFF is not set
# CONFIG_BT_SERVICE_LOG_LEVEL_ERR is not set
# CONFIG_BT_SERVICE_LOG_LEVEL_WRN is not set
# CONFIG_BT_SERVICE_LOG_LEVEL_INF is not set
# CONFIG_BT_SERVICE_LOG_LEVEL_DBG is not set
# CONFIG_BT_SERVICE_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_CTLR_ISOAL_LOG_LEVEL_INHERIT=y
CONFIG_BT_CTLR_ISOAL_LOG_LEVEL=3
# CONFIG_BT_CTLR_ISOAL_LOG_LEVEL_OFF is not set
# CONFIG_BT_CTLR_ISOAL_LOG_LEVEL_ERR is not set
# CONFIG_BT_CTLR_ISOAL_LOG_LEVEL_WRN is not set
# CONFIG_BT_CTLR_ISOAL_LOG_LEVEL_INF is not set
# CONFIG_BT_CTLR_ISOAL_LOG_LEVEL_DBG is not set
# CONFIG_BT_CTLR_ISOAL_LOG_LEVEL_DEFAULT is not set
# end of Others

#
# BR/EDR
#
CONFIG_BT_RFCOMM_LOG_LEVEL_INHERIT=y
CONFIG_BT_RFCOMM_LOG_LEVEL=3
# CONFIG_BT_RFCOMM_LOG_LEVEL_OFF is not set
# CONFIG_BT_RFCOMM_LOG_LEVEL_ERR is not set
# CONFIG_BT_RFCOMM_LOG_LEVEL_WRN is not set
# CONFIG_BT_RFCOMM_LOG_LEVEL_INF is not set
# CONFIG_BT_RFCOMM_LOG_LEVEL_DBG is not set
# CONFIG_BT_RFCOMM_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_HFP_HF_LOG_LEVEL_INHERIT=y
CONFIG_BT_HFP_HF_LOG_LEVEL=3
# CONFIG_BT_HFP_HF_LOG_LEVEL_OFF is not set
# CONFIG_BT_HFP_HF_LOG_LEVEL_ERR is not set
# CONFIG_BT_HFP_HF_LOG_LEVEL_WRN is not set
# CONFIG_BT_HFP_HF_LOG_LEVEL_INF is not set
# CONFIG_BT_HFP_HF_LOG_LEVEL_DBG is not set
# CONFIG_BT_HFP_HF_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_HFP_AG_LOG_LEVEL_INHERIT=y
CONFIG_BT_HFP_AG_LOG_LEVEL=3
# CONFIG_BT_HFP_AG_LOG_LEVEL_OFF is not set
# CONFIG_BT_HFP_AG_LOG_LEVEL_ERR is not set
# CONFIG_BT_HFP_AG_LOG_LEVEL_WRN is not set
# CONFIG_BT_HFP_AG_LOG_LEVEL_INF is not set
# CONFIG_BT_HFP_AG_LOG_LEVEL_DBG is not set
# CONFIG_BT_HFP_AG_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_AVDTP_LOG_LEVEL_INHERIT=y
CONFIG_BT_AVDTP_LOG_LEVEL=3
# CONFIG_BT_AVDTP_LOG_LEVEL_OFF is not set
# CONFIG_BT_AVDTP_LOG_LEVEL_ERR is not set
# CONFIG_BT_AVDTP_LOG_LEVEL_WRN is not set
# CONFIG_BT_AVDTP_LOG_LEVEL_INF is not set
# CONFIG_BT_AVDTP_LOG_LEVEL_DBG is not set
# CONFIG_BT_AVDTP_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_A2DP_LOG_LEVEL_INHERIT=y
CONFIG_BT_A2DP_LOG_LEVEL=3
# CONFIG_BT_A2DP_LOG_LEVEL_OFF is not set
# CONFIG_BT_A2DP_LOG_LEVEL_ERR is not set
# CONFIG_BT_A2DP_LOG_LEVEL_WRN is not set
# CONFIG_BT_A2DP_LOG_LEVEL_INF is not set
# CONFIG_BT_A2DP_LOG_LEVEL_DBG is not set
# CONFIG_BT_A2DP_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_SDP_LOG_LEVEL_INHERIT=y
CONFIG_BT_SDP_LOG_LEVEL=3
# CONFIG_BT_SDP_LOG_LEVEL_OFF is not set
# CONFIG_BT_SDP_LOG_LEVEL_ERR is not set
# CONFIG_BT_SDP_LOG_LEVEL_WRN is not set
# CONFIG_BT_SDP_LOG_LEVEL_INF is not set
# CONFIG_BT_SDP_LOG_LEVEL_DBG is not set
# CONFIG_BT_SDP_LOG_LEVEL_DEFAULT is not set
# end of BR/EDR

#
# Mesh
#
CONFIG_BT_MESH_LOG_LEVEL_INHERIT=y
CONFIG_BT_MESH_LOG_LEVEL=3
# CONFIG_BT_MESH_LOG_LEVEL_OFF is not set
# CONFIG_BT_MESH_LOG_LEVEL_ERR is not set
# CONFIG_BT_MESH_LOG_LEVEL_WRN is not set
# CONFIG_BT_MESH_LOG_LEVEL_INF is not set
# CONFIG_BT_MESH_LOG_LEVEL_DBG is not set
# CONFIG_BT_MESH_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MESH_NET_LOG_LEVEL_INHERIT=y
CONFIG_BT_MESH_NET_LOG_LEVEL=3
# CONFIG_BT_MESH_NET_LOG_LEVEL_OFF is not set
# CONFIG_BT_MESH_NET_LOG_LEVEL_ERR is not set
# CONFIG_BT_MESH_NET_LOG_LEVEL_WRN is not set
# CONFIG_BT_MESH_NET_LOG_LEVEL_INF is not set
# CONFIG_BT_MESH_NET_LOG_LEVEL_DBG is not set
# CONFIG_BT_MESH_NET_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MESH_RPL_LOG_LEVEL_INHERIT=y
CONFIG_BT_MESH_RPL_LOG_LEVEL=3
# CONFIG_BT_MESH_RPL_LOG_LEVEL_OFF is not set
# CONFIG_BT_MESH_RPL_LOG_LEVEL_ERR is not set
# CONFIG_BT_MESH_RPL_LOG_LEVEL_WRN is not set
# CONFIG_BT_MESH_RPL_LOG_LEVEL_INF is not set
# CONFIG_BT_MESH_RPL_LOG_LEVEL_DBG is not set
# CONFIG_BT_MESH_RPL_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MESH_TRANS_LOG_LEVEL_INHERIT=y
CONFIG_BT_MESH_TRANS_LOG_LEVEL=3
# CONFIG_BT_MESH_TRANS_LOG_LEVEL_OFF is not set
# CONFIG_BT_MESH_TRANS_LOG_LEVEL_ERR is not set
# CONFIG_BT_MESH_TRANS_LOG_LEVEL_WRN is not set
# CONFIG_BT_MESH_TRANS_LOG_LEVEL_INF is not set
# CONFIG_BT_MESH_TRANS_LOG_LEVEL_DBG is not set
# CONFIG_BT_MESH_TRANS_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MESH_BEACON_LOG_LEVEL_INHERIT=y
CONFIG_BT_MESH_BEACON_LOG_LEVEL=3
# CONFIG_BT_MESH_BEACON_LOG_LEVEL_OFF is not set
# CONFIG_BT_MESH_BEACON_LOG_LEVEL_ERR is not set
# CONFIG_BT_MESH_BEACON_LOG_LEVEL_WRN is not set
# CONFIG_BT_MESH_BEACON_LOG_LEVEL_INF is not set
# CONFIG_BT_MESH_BEACON_LOG_LEVEL_DBG is not set
# CONFIG_BT_MESH_BEACON_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MESH_CRYPTO_LOG_LEVEL_INHERIT=y
CONFIG_BT_MESH_CRYPTO_LOG_LEVEL=3
# CONFIG_BT_MESH_CRYPTO_LOG_LEVEL_OFF is not set
# CONFIG_BT_MESH_CRYPTO_LOG_LEVEL_ERR is not set
# CONFIG_BT_MESH_CRYPTO_LOG_LEVEL_WRN is not set
# CONFIG_BT_MESH_CRYPTO_LOG_LEVEL_INF is not set
# CONFIG_BT_MESH_CRYPTO_LOG_LEVEL_DBG is not set
# CONFIG_BT_MESH_CRYPTO_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MESH_KEYS_LOG_LEVEL_INHERIT=y
CONFIG_BT_MESH_KEYS_LOG_LEVEL=3
# CONFIG_BT_MESH_KEYS_LOG_LEVEL_OFF is not set
# CONFIG_BT_MESH_KEYS_LOG_LEVEL_ERR is not set
# CONFIG_BT_MESH_KEYS_LOG_LEVEL_WRN is not set
# CONFIG_BT_MESH_KEYS_LOG_LEVEL_INF is not set
# CONFIG_BT_MESH_KEYS_LOG_LEVEL_DBG is not set
# CONFIG_BT_MESH_KEYS_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MESH_PROV_LOG_LEVEL_INHERIT=y
CONFIG_BT_MESH_PROV_LOG_LEVEL=3
# CONFIG_BT_MESH_PROV_LOG_LEVEL_OFF is not set
# CONFIG_BT_MESH_PROV_LOG_LEVEL_ERR is not set
# CONFIG_BT_MESH_PROV_LOG_LEVEL_WRN is not set
# CONFIG_BT_MESH_PROV_LOG_LEVEL_INF is not set
# CONFIG_BT_MESH_PROV_LOG_LEVEL_DBG is not set
# CONFIG_BT_MESH_PROV_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MESH_PROVISIONER_LOG_LEVEL_INHERIT=y
CONFIG_BT_MESH_PROVISIONER_LOG_LEVEL=3
# CONFIG_BT_MESH_PROVISIONER_LOG_LEVEL_OFF is not set
# CONFIG_BT_MESH_PROVISIONER_LOG_LEVEL_ERR is not set
# CONFIG_BT_MESH_PROVISIONER_LOG_LEVEL_WRN is not set
# CONFIG_BT_MESH_PROVISIONER_LOG_LEVEL_INF is not set
# CONFIG_BT_MESH_PROVISIONER_LOG_LEVEL_DBG is not set
# CONFIG_BT_MESH_PROVISIONER_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MESH_PROVISIONEE_LOG_LEVEL_INHERIT=y
CONFIG_BT_MESH_PROVISIONEE_LOG_LEVEL=3
# CONFIG_BT_MESH_PROVISIONEE_LOG_LEVEL_OFF is not set
# CONFIG_BT_MESH_PROVISIONEE_LOG_LEVEL_ERR is not set
# CONFIG_BT_MESH_PROVISIONEE_LOG_LEVEL_WRN is not set
# CONFIG_BT_MESH_PROVISIONEE_LOG_LEVEL_INF is not set
# CONFIG_BT_MESH_PROVISIONEE_LOG_LEVEL_DBG is not set
# CONFIG_BT_MESH_PROVISIONEE_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MESH_ACCESS_LOG_LEVEL_INHERIT=y
CONFIG_BT_MESH_ACCESS_LOG_LEVEL=3
# CONFIG_BT_MESH_ACCESS_LOG_LEVEL_OFF is not set
# CONFIG_BT_MESH_ACCESS_LOG_LEVEL_ERR is not set
# CONFIG_BT_MESH_ACCESS_LOG_LEVEL_WRN is not set
# CONFIG_BT_MESH_ACCESS_LOG_LEVEL_INF is not set
# CONFIG_BT_MESH_ACCESS_LOG_LEVEL_DBG is not set
# CONFIG_BT_MESH_ACCESS_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MESH_MODEL_LOG_LEVEL_INHERIT=y
CONFIG_BT_MESH_MODEL_LOG_LEVEL=3
# CONFIG_BT_MESH_MODEL_LOG_LEVEL_OFF is not set
# CONFIG_BT_MESH_MODEL_LOG_LEVEL_ERR is not set
# CONFIG_BT_MESH_MODEL_LOG_LEVEL_WRN is not set
# CONFIG_BT_MESH_MODEL_LOG_LEVEL_INF is not set
# CONFIG_BT_MESH_MODEL_LOG_LEVEL_DBG is not set
# CONFIG_BT_MESH_MODEL_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MESH_DFU_LOG_LEVEL_INHERIT=y
CONFIG_BT_MESH_DFU_LOG_LEVEL=3
# CONFIG_BT_MESH_DFU_LOG_LEVEL_OFF is not set
# CONFIG_BT_MESH_DFU_LOG_LEVEL_ERR is not set
# CONFIG_BT_MESH_DFU_LOG_LEVEL_WRN is not set
# CONFIG_BT_MESH_DFU_LOG_LEVEL_INF is not set
# CONFIG_BT_MESH_DFU_LOG_LEVEL_DBG is not set
# CONFIG_BT_MESH_DFU_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MESH_ADV_LOG_LEVEL_INHERIT=y
CONFIG_BT_MESH_ADV_LOG_LEVEL=3
# CONFIG_BT_MESH_ADV_LOG_LEVEL_OFF is not set
# CONFIG_BT_MESH_ADV_LOG_LEVEL_ERR is not set
# CONFIG_BT_MESH_ADV_LOG_LEVEL_WRN is not set
# CONFIG_BT_MESH_ADV_LOG_LEVEL_INF is not set
# CONFIG_BT_MESH_ADV_LOG_LEVEL_DBG is not set
# CONFIG_BT_MESH_ADV_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MESH_LOW_POWER_LOG_LEVEL_INHERIT=y
CONFIG_BT_MESH_LOW_POWER_LOG_LEVEL=3
# CONFIG_BT_MESH_LOW_POWER_LOG_LEVEL_OFF is not set
# CONFIG_BT_MESH_LOW_POWER_LOG_LEVEL_ERR is not set
# CONFIG_BT_MESH_LOW_POWER_LOG_LEVEL_WRN is not set
# CONFIG_BT_MESH_LOW_POWER_LOG_LEVEL_INF is not set
# CONFIG_BT_MESH_LOW_POWER_LOG_LEVEL_DBG is not set
# CONFIG_BT_MESH_LOW_POWER_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MESH_FRIEND_LOG_LEVEL_INHERIT=y
CONFIG_BT_MESH_FRIEND_LOG_LEVEL=3
# CONFIG_BT_MESH_FRIEND_LOG_LEVEL_OFF is not set
# CONFIG_BT_MESH_FRIEND_LOG_LEVEL_ERR is not set
# CONFIG_BT_MESH_FRIEND_LOG_LEVEL_WRN is not set
# CONFIG_BT_MESH_FRIEND_LOG_LEVEL_INF is not set
# CONFIG_BT_MESH_FRIEND_LOG_LEVEL_DBG is not set
# CONFIG_BT_MESH_FRIEND_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MESH_PROXY_LOG_LEVEL_INHERIT=y
CONFIG_BT_MESH_PROXY_LOG_LEVEL=3
# CONFIG_BT_MESH_PROXY_LOG_LEVEL_OFF is not set
# CONFIG_BT_MESH_PROXY_LOG_LEVEL_ERR is not set
# CONFIG_BT_MESH_PROXY_LOG_LEVEL_WRN is not set
# CONFIG_BT_MESH_PROXY_LOG_LEVEL_INF is not set
# CONFIG_BT_MESH_PROXY_LOG_LEVEL_DBG is not set
# CONFIG_BT_MESH_PROXY_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MESH_SETTINGS_LOG_LEVEL_INHERIT=y
CONFIG_BT_MESH_SETTINGS_LOG_LEVEL=3
# CONFIG_BT_MESH_SETTINGS_LOG_LEVEL_OFF is not set
# CONFIG_BT_MESH_SETTINGS_LOG_LEVEL_ERR is not set
# CONFIG_BT_MESH_SETTINGS_LOG_LEVEL_WRN is not set
# CONFIG_BT_MESH_SETTINGS_LOG_LEVEL_INF is not set
# CONFIG_BT_MESH_SETTINGS_LOG_LEVEL_DBG is not set
# CONFIG_BT_MESH_SETTINGS_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MESH_CDB_LOG_LEVEL_INHERIT=y
CONFIG_BT_MESH_CDB_LOG_LEVEL=3
# CONFIG_BT_MESH_CDB_LOG_LEVEL_OFF is not set
# CONFIG_BT_MESH_CDB_LOG_LEVEL_ERR is not set
# CONFIG_BT_MESH_CDB_LOG_LEVEL_WRN is not set
# CONFIG_BT_MESH_CDB_LOG_LEVEL_INF is not set
# CONFIG_BT_MESH_CDB_LOG_LEVEL_DBG is not set
# CONFIG_BT_MESH_CDB_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_MESH_CFG_LOG_LEVEL_INHERIT=y
CONFIG_BT_MESH_CFG_LOG_LEVEL=3
# CONFIG_BT_MESH_CFG_LOG_LEVEL_OFF is not set
# CONFIG_BT_MESH_CFG_LOG_LEVEL_ERR is not set
# CONFIG_BT_MESH_CFG_LOG_LEVEL_WRN is not set
# CONFIG_BT_MESH_CFG_LOG_LEVEL_INF is not set
# CONFIG_BT_MESH_CFG_LOG_LEVEL_DBG is not set
# CONFIG_BT_MESH_CFG_LOG_LEVEL_DEFAULT is not set
# end of Mesh

#
# Services
#
# CONFIG_BT_BAS_LOG_LEVEL_OFF is not set
# CONFIG_BT_BAS_LOG_LEVEL_ERR is not set
# CONFIG_BT_BAS_LOG_LEVEL_WRN is not set
# CONFIG_BT_BAS_LOG_LEVEL_INF is not set
# CONFIG_BT_BAS_LOG_LEVEL_DBG is not set
CONFIG_BT_BAS_LOG_LEVEL_DEFAULT=y
CONFIG_BT_BAS_LOG_LEVEL=3
# CONFIG_BT_HRS_LOG_LEVEL_OFF is not set
# CONFIG_BT_HRS_LOG_LEVEL_ERR is not set
# CONFIG_BT_HRS_LOG_LEVEL_WRN is not set
# CONFIG_BT_HRS_LOG_LEVEL_INF is not set
# CONFIG_BT_HRS_LOG_LEVEL_DBG is not set
CONFIG_BT_HRS_LOG_LEVEL_DEFAULT=y
CONFIG_BT_HRS_LOG_LEVEL=3
# CONFIG_BT_TPS_LOG_LEVEL_OFF is not set
# CONFIG_BT_TPS_LOG_LEVEL_ERR is not set
# CONFIG_BT_TPS_LOG_LEVEL_WRN is not set
# CONFIG_BT_TPS_LOG_LEVEL_INF is not set
# CONFIG_BT_TPS_LOG_LEVEL_DBG is not set
CONFIG_BT_TPS_LOG_LEVEL_DEFAULT=y
CONFIG_BT_TPS_LOG_LEVEL=3
CONFIG_BT_IAS_CLIENT_LOG_LEVEL_INHERIT=y
CONFIG_BT_IAS_CLIENT_LOG_LEVEL=3
# CONFIG_BT_IAS_CLIENT_LOG_LEVEL_OFF is not set
# CONFIG_BT_IAS_CLIENT_LOG_LEVEL_ERR is not set
# CONFIG_BT_IAS_CLIENT_LOG_LEVEL_WRN is not set
# CONFIG_BT_IAS_CLIENT_LOG_LEVEL_INF is not set
# CONFIG_BT_IAS_CLIENT_LOG_LEVEL_DBG is not set
# CONFIG_BT_IAS_CLIENT_LOG_LEVEL_DEFAULT is not set
# CONFIG_BT_IAS_LOG_LEVEL_OFF is not set
# CONFIG_BT_IAS_LOG_LEVEL_ERR is not set
# CONFIG_BT_IAS_LOG_LEVEL_WRN is not set
# CONFIG_BT_IAS_LOG_LEVEL_INF is not set
# CONFIG_BT_IAS_LOG_LEVEL_DBG is not set
CONFIG_BT_IAS_LOG_LEVEL_DEFAULT=y
CONFIG_BT_IAS_LOG_LEVEL=3
CONFIG_BT_OTS_CLIENT_LOG_LEVEL_INHERIT=y
CONFIG_BT_OTS_CLIENT_LOG_LEVEL=3
# CONFIG_BT_OTS_CLIENT_LOG_LEVEL_OFF is not set
# CONFIG_BT_OTS_CLIENT_LOG_LEVEL_ERR is not set
# CONFIG_BT_OTS_CLIENT_LOG_LEVEL_WRN is not set
# CONFIG_BT_OTS_CLIENT_LOG_LEVEL_INF is not set
# CONFIG_BT_OTS_CLIENT_LOG_LEVEL_DBG is not set
# CONFIG_BT_OTS_CLIENT_LOG_LEVEL_DEFAULT is not set
# CONFIG_BT_OTS_LOG_LEVEL_OFF is not set
# CONFIG_BT_OTS_LOG_LEVEL_ERR is not set
# CONFIG_BT_OTS_LOG_LEVEL_WRN is not set
# CONFIG_BT_OTS_LOG_LEVEL_INF is not set
# CONFIG_BT_OTS_LOG_LEVEL_DBG is not set
CONFIG_BT_OTS_LOG_LEVEL_DEFAULT=y
CONFIG_BT_OTS_LOG_LEVEL=3
# end of Services
# end of Bluetooth logging

#
# Controller Area Network (CAN) bus subsystem
#
# end of Controller Area Network (CAN) bus subsystem

# CONFIG_CONSOLE_SUBSYS is not set

#
# System Monitoring Options
#
# CONFIG_THREAD_ANALYZER is not set
# end of System Monitoring Options

#
# Debugging Options
#
# CONFIG_DEBUG is not set
# CONFIG_STACK_USAGE is not set
# CONFIG_STACK_SENTINEL is not set
CONFIG_PRINTK=y
CONFIG_EARLY_CONSOLE=y
CONFIG_ASSERT=y
CONFIG_ASSERT_LEVEL=2
CONFIG_SPIN_VALIDATE=y
# CONFIG_FORCE_NO_ASSERT is not set
CONFIG_ASSERT_VERBOSE=y
# CONFIG_ASSERT_NO_FILE_INFO is not set
# CONFIG_ASSERT_NO_COND_INFO is not set
# CONFIG_ASSERT_NO_MSG_INFO is not set
# CONFIG_ASSERT_TEST is not set
# CONFIG_OVERRIDE_FRAME_POINTER_DEFAULT is not set
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_THREAD_INFO is not set
# CONFIG_DEBUG_COREDUMP is not set
# end of Debugging Options

# CONFIG_MIPI_STP_DECODER is not set
# CONFIG_DISK_ACCESS is not set
# CONFIG_DSP is not set
# CONFIG_EMUL is not set
# CONFIG_CHARACTER_FRAMEBUFFER is not set

#
# File Systems
#
# CONFIG_FILE_SYSTEM is not set
# CONFIG_FCB is not set
CONFIG_NVS=y
# CONFIG_NVS_LOOKUP_CACHE is not set
# CONFIG_NVS_DATA_CRC is not set
# CONFIG_NVS_LOG_LEVEL_OFF is not set
# CONFIG_NVS_LOG_LEVEL_ERR is not set
# CONFIG_NVS_LOG_LEVEL_WRN is not set
# CONFIG_NVS_LOG_LEVEL_INF is not set
# CONFIG_NVS_LOG_LEVEL_DBG is not set
CONFIG_NVS_LOG_LEVEL_DEFAULT=y
CONFIG_NVS_LOG_LEVEL=3
# end of File Systems

#
# Inter Processor Communication
#
# CONFIG_RPMSG_SERVICE is not set
CONFIG_IPC_SERVICE=y
CONFIG_IPC_SERVICE_REG_BACKEND_PRIORITY=46
CONFIG_IPC_SERVICE_BACKEND_RPMSG=y
CONFIG_IPC_SERVICE_BACKEND_RPMSG_WQ_STACK_SIZE=1024
CONFIG_IPC_SERVICE_BACKEND_RPMSG_NUM_ENDPOINTS_PER_INSTANCE=2
CONFIG_IPC_SERVICE_RPMSG=y
CONFIG_IPC_SERVICE_STATIC_VRINGS=y
CONFIG_IPC_SERVICE_STATIC_VRINGS_MEM_ALIGNMENT=4
# CONFIG_IPC_SERVICE_ICMSG is not set
# CONFIG_IPC_SERVICE_ICMSG_ME is not set
# CONFIG_IPC_SERVICE_LOG_LEVEL_OFF is not set
# CONFIG_IPC_SERVICE_LOG_LEVEL_ERR is not set
# CONFIG_IPC_SERVICE_LOG_LEVEL_WRN is not set
# CONFIG_IPC_SERVICE_LOG_LEVEL_INF is not set
# CONFIG_IPC_SERVICE_LOG_LEVEL_DBG is not set
CONFIG_IPC_SERVICE_LOG_LEVEL_DEFAULT=y
CONFIG_IPC_SERVICE_LOG_LEVEL=3
# end of Inter Processor Communication

# CONFIG_JWT is not set
# CONFIG_LLEXT is not set

#
# Linkable loadable Extension Development Kit (EDK)
#
CONFIG_LLEXT_EDK_NAME="llext-edk"
# CONFIG_LLEXT_EDK_USERSPACE_ONLY is not set
# end of Linkable loadable Extension Development Kit (EDK)

#
# Logging
#
CONFIG_LOG_CORE_INIT_PRIORITY=0
CONFIG_LOG_MODE_DEFERRED=y
# CONFIG_LOG_MODE_IMMEDIATE is not set
# CONFIG_LOG_MODE_MINIMAL is not set
# CONFIG_LOG_FRONTEND is not set
# CONFIG_LOG_FRONTEND_OPT_API is not set
# CONFIG_LOG_CUSTOM_HEADER is not set
# CONFIG_LOG_MULTIDOMAIN is not set

#
# Logging levels filtering
#
# CONFIG_LOG_RUNTIME_FILTERING is not set
CONFIG_LOG_DEFAULT_LEVEL=3
CONFIG_LOG_OVERRIDE_LEVEL=0
CONFIG_LOG_MAX_LEVEL=4
# end of Logging levels filtering

#
# Processing
#
# CONFIG_LOG_PRINTK is not set
CONFIG_LOG_MODE_OVERFLOW=y
# CONFIG_LOG_BLOCK_IN_THREAD is not set
CONFIG_LOG_PROCESS_TRIGGER_THRESHOLD=10
CONFIG_LOG_PROCESS_THREAD=y
CONFIG_LOG_PROCESS_THREAD_STARTUP_DELAY_MS=0
CONFIG_LOG_PROCESS_THREAD_SLEEP_MS=1000
CONFIG_LOG_PROCESS_THREAD_STACK_SIZE=2048
# CONFIG_LOG_PROCESS_THREAD_CUSTOM_PRIORITY is not set
CONFIG_LOG_TRACE_SHORT_TIMESTAMP=y
# CONFIG_LOG_TIMESTAMP_64BIT is not set
# CONFIG_LOG_SPEED is not set
# end of Processing

#
# Output Formatting
#

#
# Prepend non-hexdump log message with function name
#
# CONFIG_LOG_FUNC_NAME_PREFIX_ERR is not set
# CONFIG_LOG_FUNC_NAME_PREFIX_WRN is not set
# CONFIG_LOG_FUNC_NAME_PREFIX_INF is not set
CONFIG_LOG_FUNC_NAME_PREFIX_DBG=y
# end of Prepend non-hexdump log message with function name

# CONFIG_LOG_MIPI_SYST_ENABLE is not set
# CONFIG_LOG_THREAD_ID_PREFIX is not set
# CONFIG_LOG_CUSTOM_FORMAT_SUPPORT is not set
CONFIG_LOG_BACKEND_SHOW_COLOR=y
# CONFIG_LOG_INFO_COLOR_GREEN is not set
CONFIG_LOG_TAG_MAX_LEN=0
CONFIG_LOG_BACKEND_FORMAT_TIMESTAMP=y
# CONFIG_LOG_OUTPUT_FORMAT_LINUX_TIMESTAMP is not set
# CONFIG_LOG_OUTPUT_FORMAT_CUSTOM_TIMESTAMP is not set
# end of Output Formatting

#
# Backends
#
# CONFIG_LOG_BACKEND_BLE is not set
CONFIG_LOG_BACKEND_RTT=y
# CONFIG_LOG_BACKEND_RTT_MODE_DROP is not set
CONFIG_LOG_BACKEND_RTT_MODE_BLOCK=y
# CONFIG_LOG_BACKEND_RTT_MODE_OVERWRITE is not set
CONFIG_LOG_BACKEND_RTT_OUTPUT_TEXT=y
# CONFIG_LOG_BACKEND_RTT_OUTPUT_DICTIONARY is not set
# CONFIG_LOG_BACKEND_RTT_OUTPUT_CUSTOM is not set
CONFIG_LOG_BACKEND_RTT_OUTPUT_DEFAULT=0
CONFIG_LOG_BACKEND_RTT_OUTPUT_BUFFER_SIZE=16
CONFIG_LOG_BACKEND_RTT_RETRY_CNT=4
CONFIG_LOG_BACKEND_RTT_RETRY_DELAY_MS=5
CONFIG_LOG_BACKEND_RTT_BUFFER=0
# CONFIG_LOG_BACKEND_SWO is not set
# CONFIG_LOG_BACKEND_UART is not set
# CONFIG_LOG_BACKEND_IPC_SERVICE is not set
# end of Backends

#
# Misc
#
CONFIG_LOG_DOMAIN_ID=0
CONFIG_LOG_USE_VLA=y
CONFIG_LOG_SIMPLE_MSG_OPTIMIZE=y
# CONFIG_LOG_ALWAYS_RUNTIME is not set
# CONFIG_LOG_FMT_SECTION is not set
# CONFIG_LOG_FMT_STRING_VALIDATE is not set
# CONFIG_LOG_MEM_UTILIZATION is not set
CONFIG_LOG_FAILURE_REPORT_PERIOD=1000
# end of Misc

CONFIG_LOG_OUTPUT=y
# end of Logging

CONFIG_MEM_ATTR=y
# CONFIG_MEM_ATTR_HEAP is not set

#
# Device Management
#

#
# Host command handler subsystem
#
# CONFIG_EC_HOST_CMD is not set
# end of Host command handler subsystem

# CONFIG_OSDP is not set
# end of Device Management

# CONFIG_MODBUS is not set
# CONFIG_MODEM_MODULES is not set

#
# Networking
#
CONFIG_NET_BUF=y
# CONFIG_NET_BUF_LOG is not set
# CONFIG_NET_BUF_LOG_LEVEL_OFF is not set
# CONFIG_NET_BUF_LOG_LEVEL_ERR is not set
# CONFIG_NET_BUF_LOG_LEVEL_WRN is not set
# CONFIG_NET_BUF_LOG_LEVEL_INF is not set
# CONFIG_NET_BUF_LOG_LEVEL_DBG is not set
CONFIG_NET_BUF_LOG_LEVEL_DEFAULT=y
CONFIG_NET_BUF_LOG_LEVEL=3
# CONFIG_NET_BUF_POOL_USAGE is not set
CONFIG_NET_BUF_ALIGNMENT=0
# CONFIG_NETWORKING is not set
# end of Networking

#
# Power Management
#
# end of Power Management

#
# Portability
#
# end of Portability

#
# Random Number Generators
#
# CONFIG_TEST_RANDOM_GENERATOR is not set
CONFIG_TIMER_RANDOM_INITIAL_STATE=123456789
# end of Random Number Generators

# CONFIG_RTIO is not set

#
# SD
#
# CONFIG_MMC_STACK is not set
# CONFIG_SDMMC_STACK is not set
# CONFIG_SDIO_STACK is not set
# end of SD

CONFIG_SETTINGS=y
# CONFIG_SETTINGS_LOG_LEVEL_OFF is not set
# CONFIG_SETTINGS_LOG_LEVEL_ERR is not set
# CONFIG_SETTINGS_LOG_LEVEL_WRN is not set
# CONFIG_SETTINGS_LOG_LEVEL_INF is not set
# CONFIG_SETTINGS_LOG_LEVEL_DBG is not set
CONFIG_SETTINGS_LOG_LEVEL_DEFAULT=y
CONFIG_SETTINGS_LOG_LEVEL=3
# CONFIG_SETTINGS_RUNTIME is not set
CONFIG_SETTINGS_DYNAMIC_HANDLERS=y
CONFIG_SETTINGS_NVS=y
# CONFIG_SETTINGS_NVS_NAME_CACHE is not set
# CONFIG_SETTINGS_CUSTOM is not set
# CONFIG_SETTINGS_NONE is not set
CONFIG_SETTINGS_NVS_SECTOR_SIZE_MULT=1
CONFIG_SETTINGS_NVS_SECTOR_COUNT=8
# CONFIG_SHELL is not set
# CONFIG_STATS is not set

#
# Storage
#
CONFIG_FLASH_MAP=y
# CONFIG_FLASH_AREA_CHECK_INTEGRITY is not set
# CONFIG_FLASH_MAP_LABELS is not set
# CONFIG_STREAM_FLASH is not set
# end of Storage

# CONFIG_TASK_WDT is not set

#
# Testing
#
# CONFIG_ZTEST is not set
# CONFIG_ZTEST_MOCKING is not set
# CONFIG_ZTRESS is not set
# CONFIG_TEST is not set
CONFIG_COVERAGE_GCOV_HEAP_SIZE=16384
# CONFIG_FORCE_COVERAGE is not set
# CONFIG_TEST_USERSPACE is not set
# end of Testing

# CONFIG_TIMING_FUNCTIONS is not set
# CONFIG_TRACING is not set
# CONFIG_USB_DEVICE_STACK is not set
# CONFIG_USB_DEVICE_STACK_NEXT is not set
# CONFIG_USB_HOST_STACK is not set
# CONFIG_USBC_STACK is not set
# CONFIG_ZBUS is not set
# CONFIG_MODULES is not set
# end of Subsystems and OS Services

CONFIG_TOOLCHAIN_ZEPHYR_0_16=y
CONFIG_TOOLCHAIN_ZEPHYR_SUPPORTS_THREAD_LOCAL_STORAGE=y

#
# Build and Link Features
#

#
# Linker Options
#
# CONFIG_LINKER_ORPHAN_SECTION_PLACE is not set
CONFIG_LINKER_ORPHAN_SECTION_WARN=y
# CONFIG_LINKER_ORPHAN_SECTION_ERROR is not set
CONFIG_ROM_END_OFFSET=0
CONFIG_LD_LINKER_SCRIPT_SUPPORTED=y
CONFIG_LD_LINKER_TEMPLATE=y
# CONFIG_CMAKE_LINKER_GENERATOR is not set
# CONFIG_HAVE_CUSTOM_LINKER_SCRIPT is not set
CONFIG_LINKER_SORT_BY_ALIGNMENT=y

#
# Linker Sections
#
# CONFIG_LINKER_USE_BOOT_SECTION is not set
# CONFIG_LINKER_USE_PINNED_SECTION is not set
CONFIG_LINKER_GENERIC_SECTIONS_PRESENT_AT_BOOT=y
CONFIG_LINKER_LAST_SECTION_ID=y
CONFIG_LINKER_LAST_SECTION_ID_PATTERN=0xE015E015
CONFIG_LINKER_USE_RELAX=y
# end of Linker Sections

CONFIG_LINKER_ITERABLE_SUBALIGN=4
CONFIG_LINKER_DEVNULL_SUPPORT=y
# CONFIG_LINKER_DEVNULL_MEMORY is not set
# end of Linker Options

#
# Compiler Options
#
# CONFIG_STD_C90 is not set
CONFIG_STD_C99=y
# CONFIG_STD_C11 is not set
# CONFIG_STD_C17 is not set
# CONFIG_STD_C23 is not set
CONFIG_TOOLCHAIN_SUPPORTS_GNU_EXTENSIONS=y
# CONFIG_GNU_C_EXTENSIONS is not set
# CONFIG_CODING_GUIDELINE_CHECK is not set
# CONFIG_COMPILER_FREESTANDING is not set
CONFIG_SIZE_OPTIMIZATIONS=y
# CONFIG_SPEED_OPTIMIZATIONS is not set
# CONFIG_DEBUG_OPTIMIZATIONS is not set
# CONFIG_NO_OPTIMIZATIONS is not set
# CONFIG_COMPILER_WARNINGS_AS_ERRORS is not set
# CONFIG_COMPILER_SAVE_TEMPS is not set
CONFIG_COMPILER_TRACK_MACRO_EXPANSION=y
CONFIG_COMPILER_COLOR_DIAGNOSTICS=y
# CONFIG_FORTIFY_SOURCE_NONE is not set
CONFIG_FORTIFY_SOURCE_COMPILE_TIME=y
# CONFIG_FORTIFY_SOURCE_RUN_TIME is not set
CONFIG_COMPILER_OPT=""
# CONFIG_MISRA_SANE is not set
# end of Compiler Options

# CONFIG_ASSERT_ON_ERRORS is not set
# CONFIG_NO_RUNTIME_CHECKS is not set
CONFIG_RUNTIME_ERROR_CHECKS=y

#
# Build Options
#
CONFIG_KERNEL_BIN_NAME="zephyr"
CONFIG_OUTPUT_STAT=y
# CONFIG_OUTPUT_SYMBOLS is not set
# CONFIG_OUTPUT_DISASSEMBLY is not set
CONFIG_OUTPUT_PRINT_MEMORY_USAGE=y
# CONFIG_CLEANUP_INTERMEDIATE_FILES is not set
# CONFIG_BUILD_NO_GAP_FILL is not set
# CONFIG_BUILD_OUTPUT_EXE is not set
# CONFIG_BUILD_OUTPUT_S19 is not set
# CONFIG_BUILD_OUTPUT_UF2 is not set
# CONFIG_BUILD_OUTPUT_STRIPPED is not set
# CONFIG_BUILD_OUTPUT_COMPRESS_DEBUG_SECTIONS is not set
# CONFIG_BUILD_ALIGN_LMA is not set
# CONFIG_APPLICATION_DEFINED_SYSCALL is not set
# CONFIG_MAKEFILE_EXPORTS is not set
# CONFIG_BUILD_OUTPUT_META is not set
CONFIG_BUILD_OUTPUT_STRIP_PATHS=y
CONFIG_CHECK_INIT_PRIORITIES=y
# CONFIG_EMIT_ALL_SYSCALLS is not set
# end of Build Options

CONFIG_WARN_DEPRECATED=y
CONFIG_ENFORCE_ZEPHYR_STDINT=y
# end of Build and Link Features

#
# Boot Options
#
# CONFIG_IS_BOOTLOADER is not set
# CONFIG_BOOTLOADER_BOSSA is not set
# end of Boot Options

#
# Nordic UART BLE GATT service sample
#
CONFIG_BT_NUS_THREAD_STACK_SIZE=1024
CONFIG_BT_NUS_UART_BUFFER_SIZE=40
CONFIG_BT_NUS_SECURITY_ENABLED=y
CONFIG_BT_NUS_UART_RX_WAIT_TIME=50000
# end of Nordic UART BLE GATT service sample

build/ipc_radio/zephyr/.config

# CONFIG_IPC_RADIO_802154 is not set
CONFIG_IPC_RADIO_BT=y
CONFIG_IPC_RADIO_BT_HCI_IPC=y
CONFIG_BT_MAX_CONN=16
# CONFIG_INPUT is not set
# CONFIG_WIFI is not set
# CONFIG_MIPI_DSI is not set
# CONFIG_MODEM is not set
# CONFIG_SPI is not set
CONFIG_BT_HCI_ACL_FLOW_CONTROL=y
CONFIG_BT_HCI_VS=y
CONFIG_FLASH_LOAD_SIZE=0
CONFIG_SRAM_SIZE=64
CONFIG_FLASH_LOAD_OFFSET=0
CONFIG_MBOX_NRFX_IPC=y
CONFIG_BT_CTLR=y
CONFIG_NUM_IRQS=30
CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC=32768
CONFIG_FLASH_SIZE=256
CONFIG_FLASH_BASE_ADDRESS=0x1000000
CONFIG_MP_MAX_NUM_CPUS=1
CONFIG_PLATFORM_SPECIFIC_INIT=y
CONFIG_SYS_CLOCK_TICKS_PER_SEC=32768
CONFIG_ROM_START_OFFSET=0
# CONFIG_PINCTRL is not set
CONFIG_BUILD_OUTPUT_BIN=y
CONFIG_XIP=y
CONFIG_MAIN_STACK_SIZE=2048
CONFIG_IDLE_STACK_SIZE=256
CONFIG_HAS_FLASH_LOAD_OFFSET=y
# CONFIG_SRAM_VECTOR_TABLE is not set
CONFIG_CPU_HAS_ARM_MPU=y
# CONFIG_COUNTER is not set
# CONFIG_SHARED_INTERRUPTS is not set
# CONFIG_PM_DEVICE is not set
CONFIG_TICKLESS_KERNEL=y
CONFIG_CLOCK_CONTROL_INIT_PRIORITY=30
# CONFIG_USE_DT_CODE_PARTITION is not set
CONFIG_HW_STACK_PROTECTION=y
# CONFIG_CODE_DATA_RELOCATION_SRAM is not set
CONFIG_GPIO=y
# CONFIG_SERIAL is not set
# CONFIG_CPU_HAS_CUSTOM_FIXED_SOC_MPU_REGIONS is not set
CONFIG_TINYCRYPT=y
# CONFIG_MBEDTLS is not set
# CONFIG_MEMC is not set
CONFIG_KERNEL_ENTRY="__start"
# CONFIG_MULTI_LEVEL_INTERRUPTS is not set
# CONFIG_DYNAMIC_INTERRUPTS is not set
# CONFIG_CACHE is not set
# CONFIG_LOG is not set
# CONFIG_CODE_DATA_RELOCATION is not set
CONFIG_SYSTEM_WORKQUEUE_STACK_SIZE=2048
CONFIG_DCACHE_LINE_SIZE=32
CONFIG_GEN_IRQ_VECTOR_TABLE=y
CONFIG_SOC="nrf5340"
# CONFIG_RESET is not set
CONFIG_ARCH_SW_ISR_TABLE_ALIGN=4
CONFIG_NRF_RTC_TIMER=y
# CONFIG_IPC_SERVICE_BACKEND_RPMSG_SHMEM_RESET is not set
CONFIG_LOG_DOMAIN_NAME="net"
CONFIG_BUILD_OUTPUT_HEX=y
CONFIG_CLOCK_CONTROL=y
CONFIG_ARCH_HAS_CUSTOM_BUSY_WAIT=y
CONFIG_SOC_HAS_TIMING_FUNCTIONS=y
# CONFIG_SYSCON is not set
CONFIG_ENTROPY_INIT_PRIORITY=50
CONFIG_GEN_ISR_TABLES=y
CONFIG_GEN_IRQ_START_VECTOR=0
CONFIG_GEN_SW_ISR_TABLE=y
CONFIG_SRAM_OFFSET=0
# CONFIG_REBOOT is not set
# CONFIG_POWER_DOMAIN is not set
CONFIG_CONSOLE=y
CONFIG_SOC_SERIES="nrf53"
CONFIG_ARCH_IRQ_VECTOR_TABLE_ALIGN=4
CONFIG_ISR_STACK_SIZE=2048
# CONFIG_SCHED_CPU_MASK is not set
# CONFIG_WATCHDOG is not set
CONFIG_ICACHE_LINE_SIZE=32
CONFIG_PRIVILEGED_STACK_SIZE=1024

#
# Devicetree Info
#
CONFIG_DT_HAS_ARDUINO_HEADER_R3_ENABLED=y
CONFIG_DT_HAS_ARM_ARMV8M_MPU_ENABLED=y
CONFIG_DT_HAS_ARM_CORTEX_M33_ENABLED=y
CONFIG_DT_HAS_ARM_V8M_NVIC_ENABLED=y
CONFIG_DT_HAS_FIXED_PARTITIONS_ENABLED=y
CONFIG_DT_HAS_GPIO_KEYS_ENABLED=y
CONFIG_DT_HAS_GPIO_LEDS_ENABLED=y
CONFIG_DT_HAS_MMIO_SRAM_ENABLED=y
CONFIG_DT_HAS_NORDIC_MBOX_NRF_IPC_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_ACL_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_CCM_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_CLOCK_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_DPPIC_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_ECB_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_EGU_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_FICR_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_GPIO_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_GPIOTE_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_GPREGRET_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_IEEE802154_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_IPC_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_PINCTRL_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_POWER_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_RADIO_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_RNG_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_SPIM_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_SWI_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_TEMP_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_UARTE_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_UICR_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_VMC_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_WDT_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF21540_FEM_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF21540_FEM_SPI_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF53_FLASH_CONTROLLER_ENABLED=y
CONFIG_DT_HAS_SOC_NV_FLASH_ENABLED=y
CONFIG_DT_HAS_ZEPHYR_BT_HCI_ENTROPY_ENABLED=y
CONFIG_DT_HAS_ZEPHYR_IPC_OPENAMP_STATIC_VRINGS_ENABLED=y
CONFIG_DT_HAS_ZEPHYR_MEMORY_REGION_ENABLED=y
# end of Devicetree Info

#
# Modules
#

#
# Available modules.
#

#
# nrf (C:/ncs/v2.7.0/nrf)
#
CONFIG_SHIELD_NRF21540EK=y
CONFIG_MBOX=y
CONFIG_NUM_METAIRQ_PRIORITIES=0
# CONFIG_INIT_STACKS is not set
CONFIG_MPSL_WORK_STACK_SIZE=1024

#
# Nordic nRF Connect
#
CONFIG_HIDE_CHILD_PARENT_CONFIG=y
CONFIG_WARN_EXPERIMENTAL=y
CONFIG_BT_BUF_CMD_TX_COUNT=10
CONFIG_INIT_ARCH_HW_AT_BOOT=y
CONFIG_NORDIC_QSPI_NOR_FLASH_LAYOUT_PAGE_SIZE=2048
# CONFIG_GETOPT is not set
# CONFIG_NCS_SAMPLES_DEFAULTS is not set
# CONFIG_NCS_SAMPLE_EMPTY_APP_CORE_CHILD_IMAGE is not set
# CONFIG_NCS_SAMPLE_DTM_REMOTE_HCI_CHILD_IMAGE is not set

#
# Image build variants
#
# CONFIG_NCS_MCUBOOT_IN_BUILD is not set
# end of Image build variants

# CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU_SPEEDUP is not set
CONFIG_BT_BUF_ACL_TX_SIZE=27
CONFIG_BT_BUF_ACL_RX_SIZE=27
CONFIG_BT_CTLR_DATA_LENGTH_MAX=27

#
# Subsystems
#

#
# Bootloader
#
# CONFIG_BUILD_S1_VARIANT is not set
# CONFIG_SECURE_BOOT is not set
CONFIG_PM_PARTITION_SIZE_PROVISION=0x280
# CONFIG_B0_MIN_PARTITION_SIZE is not set
CONFIG_PM_PARTITION_SIZE_B0_IMAGE=0x7800
# CONFIG_IS_SECURE_BOOTLOADER is not set

#
# Secure Boot firmware validation
#
CONFIG_SB_VALIDATION_INFO_MAGIC=0x86518483
CONFIG_SB_VALIDATION_POINTER_MAGIC=0x6919b47e
CONFIG_SB_VALIDATION_INFO_CRYPTO_ID=1
CONFIG_SB_VALIDATION_INFO_VERSION=2
CONFIG_SB_VALIDATION_METADATA_OFFSET=0
CONFIG_SB_VALIDATE_FW_HASH=y
# end of Secure Boot firmware validation

# CONFIG_SECURE_BOOT_STORAGE is not set
# end of Bootloader

#
# Bluetooth Low Energy
#
CONFIG_BT_COMPANY_ID_NORDIC=0x0059
CONFIG_BT_COMPANY_ID=0x0059
CONFIG_BT_LL_SOFTDEVICE_HEADERS_INCLUDE=y
CONFIG_BT_LL_SOFTDEVICE=y
CONFIG_BT_CTLR_DF_SUPPORT=y

#
# SoftDevice Controller
#
CONFIG_BT_LL_SOFTDEVICE_BUILD_TYPE_LIB=y
CONFIG_BT_HCI_TX_STACK_SIZE=1536
CONFIG_BT_RX_STACK_SIZE=768
# CONFIG_BT_CTLR_SDC_QOS_CHANNEL_SURVEY is not set
# CONFIG_BT_CTLR_SDC_ALLOW_PARALLEL_SCANNING_AND_INITIATING is not set
CONFIG_BT_CTLR_SDC_PERIPHERAL_COUNT=1
# CONFIG_BT_CTLR_SDC_MAX_CONN_EVENT_LEN_DEFAULT_OVERRIDE is not set
CONFIG_BT_CTLR_SDC_MAX_CONN_EVENT_LEN_DEFAULT=7500
CONFIG_BT_CTLR_SDC_CONN_EVENT_EXTEND_DEFAULT=y
CONFIG_BT_CTLR_SDC_CENTRAL_ACL_EVENT_SPACING_DEFAULT=7500
# CONFIG_BT_CTLR_SDC_PERIODIC_ADV_EVENT_LEN_DEFAULT_OVERRIDE is not set
CONFIG_BT_CTLR_SDC_PERIODIC_ADV_EVENT_LEN_DEFAULT=7500
CONFIG_BT_CTLR_SDC_TX_PACKET_COUNT=3
CONFIG_BT_CTLR_SDC_RX_PACKET_COUNT=2
CONFIG_BT_CTLR_SDC_SCAN_BUFFER_COUNT=3
CONFIG_BT_CTLR_SDC_PERIODIC_SYNC_BUFFER_COUNT=3
CONFIG_BT_CTLR_SDC_RX_PRIO=6
# CONFIG_BT_CTLR_DF is not set
CONFIG_BT_LL_SOFTDEVICE_MULTIROLE=y
CONFIG_BT_CTLR_FAL_SIZE=8
CONFIG_BT_CTLR_ECDH_LIB_OBERON=y
# CONFIG_BT_CTLR_ECDH_LIB_TINYCRYPT is not set
CONFIG_BT_CTLR_ECDH_STACK_SIZE=900
CONFIG_BT_CTLR_ECDH_IN_MPSL_WORK=y
# CONFIG_BT_CTLR_SDC_EVENT_TRIGGER is not set
CONFIG_BT_CTLR_SDC_BIG_RESERVED_TIME_US=1600
CONFIG_BT_CTLR_SDC_CIG_RESERVED_TIME_US=1300
CONFIG_BT_CTLR_SDC_CIS_SUBEVENT_LENGTH_US=0
# end of SoftDevice Controller

#
# BLE Libraries
#
# CONFIG_BT_GATT_POOL is not set
# CONFIG_BT_GATT_DM is not set
# CONFIG_BT_ADV_PROV is not set
# CONFIG_BT_SCAN is not set
# CONFIG_BT_CONN_CTX is not set

#
# Bluetooth Services
#
# CONFIG_BT_AMS_CLIENT is not set
# CONFIG_BT_ANCS_CLIENT is not set
# CONFIG_BT_BAS_CLIENT is not set
# CONFIG_BT_BMS is not set
# CONFIG_BT_CTS_CLIENT is not set
# CONFIG_BT_DFU_SMP is not set
# CONFIG_BT_GATTP is not set
# CONFIG_BT_HIDS is not set
# CONFIG_BT_HOGP is not set
# CONFIG_BT_LBS is not set
# CONFIG_BT_NSMS is not set
# CONFIG_BT_NUS is not set
# CONFIG_BT_NUS_CLIENT is not set
# CONFIG_BT_RSCS is not set
# CONFIG_BT_THROUGHPUT is not set
# CONFIG_BT_LATENCY is not set
# CONFIG_BT_LATENCY_CLIENT is not set
# CONFIG_BT_HRS_CLIENT is not set
# CONFIG_BT_DDFS is not set
# CONFIG_BT_MDS is not set
# CONFIG_BT_CGMS is not set
# CONFIG_BT_FAST_PAIR is not set
CONFIG_SYSTEM_WORKQUEUE_PRIORITY=-1
# end of Bluetooth Services

#
# BLE over nRF RPC
#
CONFIG_HEAP_MEM_POOL_SIZE=8192
# CONFIG_BT_RPC_STACK is not set
CONFIG_BT_CENTRAL=y
CONFIG_BT_PERIPHERAL=y
CONFIG_BT_OBSERVER=y
CONFIG_BT_BROADCASTER=y
CONFIG_BT_CONN=y
CONFIG_BT_REMOTE_VERSION=y
CONFIG_BT_PHY_UPDATE=y
CONFIG_BT_DATA_LEN_UPDATE=y
# CONFIG_BT_EXT_ADV is not set
CONFIG_BT_BUF_ACL_TX_COUNT=7
CONFIG_BT_BUF_ACL_RX_COUNT=6
CONFIG_BT_BUF_EVT_RX_SIZE=68
CONFIG_BT_BUF_EVT_RX_COUNT=10
CONFIG_BT_BUF_EVT_DISCARDABLE_SIZE=43
CONFIG_BT_BUF_CMD_TX_SIZE=65
CONFIG_BT_HAS_HCI_VS=y
# CONFIG_BT_HCI_VS_FATAL_ERROR is not set
# CONFIG_BT_HCI_MESH_EXT is not set
# CONFIG_BT_WAIT_NOP is not set
CONFIG_BT_RPA=y
CONFIG_BT_ASSERT=y
CONFIG_BT_ASSERT_VERBOSE=y
# CONFIG_BT_ASSERT_PANIC is not set
CONFIG_BT_DEBUG_NONE=y
# CONFIG_BT_DEBUG_LOG is not set
# CONFIG_BT_DEBUG_MONITOR_UART is not set
# CONFIG_BT_LONG_WQ is not set
# CONFIG_BT_HCI_TX_STACK_SIZE_WITH_PROMPT is not set
CONFIG_BT_HCI_TX_PRIO=7
# CONFIG_BT_RECV_WORKQ_SYS is not set
CONFIG_BT_RECV_WORKQ_BT=y
CONFIG_BT_RX_PRIO=8
CONFIG_BT_DRIVER_RX_HIGH_PRIO=6
# CONFIG_BT_ECC is not set
# CONFIG_BT_HOST_CCM is not set
# CONFIG_BT_LOG_SNIFFER_INFO is not set
# CONFIG_BT_TESTING is not set
# CONFIG_BT_HCI_VS_EVT_USER is not set
# end of BLE over nRF RPC
# end of Bluetooth Low Energy

#
# DFU
#
# CONFIG_DFU_MULTI_IMAGE is not set
# CONFIG_DFU_TARGET is not set
# end of DFU

# CONFIG_ESB is not set

#
# Peripheral CPU DFU (PCD)
#
# CONFIG_PCD is not set
# CONFIG_PCD_APP is not set
CONFIG_PCD_VERSION_PAGE_BUF_SIZE=2046
# CONFIG_PCD_NET is not set
# end of Peripheral CPU DFU (PCD)

#
# Networking
#

#
# Application protocols
#

#
# nRF Cloud
#

#
# Client ID (nRF Cloud Device ID)
#
CONFIG_NRF_CLOUD_CLIENT_ID_SRC_COMPILE_TIME=y
CONFIG_NRF_CLOUD_CLIENT_ID="my-client-id"
# end of Client ID (nRF Cloud Device ID)

# CONFIG_NRF_CLOUD_MQTT is not set
# CONFIG_NRF_CLOUD_FOTA is not set
CONFIG_FOTA_USE_NRF_CLOUD_SETTINGS_AREA=y
CONFIG_FOTA_DL_TIMEOUT_MIN=15
# CONFIG_NRF_CLOUD_FOTA_FULL_MODEM_UPDATE is not set
# CONFIG_NRF_CLOUD_REST is not set
# CONFIG_NRF_CLOUD_LOCATION_PARSE_ANCHORS is not set
# CONFIG_NRF_CLOUD_ALERT is not set
CONFIG_NRF_CLOUD_LOG_OUTPUT_LEVEL=1
# CONFIG_NRF_CLOUD_LOG_INCLUDE_LEVEL_0 is not set
CONFIG_NRF_CLOUD_LOG_BUF_SIZE=256
# CONFIG_NRF_CLOUD_COAP is not set

#
# Send shadow info sections on initial connect (MQTT/CoAP)
#
# end of Send shadow info sections on initial connect (MQTT/CoAP)

# CONFIG_NRF_CLOUD_GATEWAY is not set
# end of nRF Cloud

# CONFIG_REST_CLIENT is not set
# CONFIG_DOWNLOAD_CLIENT is not set
# CONFIG_AWS_IOT is not set
# CONFIG_AWS_JOBS is not set
# CONFIG_AZURE_IOT_HUB is not set

#
# Self-Registration (Zi ZHu Ce)
#
# end of Self-Registration (Zi ZHu Ce)

# CONFIG_ICAL_PARSER is not set
# CONFIG_FTP_CLIENT is not set
# CONFIG_LWM2M_CLIENT_UTILS is not set
# CONFIG_WIFI_CREDENTIALS is not set
# CONFIG_WIFI_CREDENTIALS_STATIC is not set
# CONFIG_MQTT_HELPER is not set
# CONFIG_NRF_MCUMGR_SMP_CLIENT is not set
# end of Application protocols
# end of Networking

#
# NFC
#
# CONFIG_NFC_NDEF is not set
# CONFIG_NFC_NDEF_PARSER is not set
# CONFIG_NFC_NDEF_PAYLOAD_TYPE_COMMON is not set
# CONFIG_NFC_T2T_PARSER is not set
# CONFIG_NFC_T4T_NDEF_FILE is not set
# CONFIG_NFC_T4T_ISODEP is not set
# CONFIG_NFC_T4T_APDU is not set
# CONFIG_NFC_T4T_CC_FILE is not set
# CONFIG_NFC_T4T_HL_PROCEDURE is not set
# CONFIG_NFC_PLATFORM is not set
# CONFIG_NFC_TNEP_TAG is not set
# CONFIG_NFC_TNEP_POLLER is not set
# CONFIG_NFC_TNEP_CH is not set
# end of NFC

# CONFIG_APP_EVENT_MANAGER is not set
# CONFIG_NRF_PROFILER is not set
# CONFIG_FW_INFO is not set

#
# Debug
#
# CONFIG_CPU_LOAD is not set
# CONFIG_PPI_TRACE is not set
# end of Debug

# CONFIG_SHELL_BT_NUS is not set
# CONFIG_SHELL_IPC is not set

#
# Multiprotocol service layer (MPSL)
#
# CONFIG_MPSL_FEM_ONLY is not set
CONFIG_MPSL_FEM_ANY_SUPPORT=y
CONFIG_MPSL_FEM_NRF21540_GPIO_SUPPORT=y
CONFIG_MPSL_FEM_NRF21540_GPIO_SPI_SUPPORT=y
CONFIG_MPSL_FEM_NCS_SUPPORTED_FEM_USED=y
CONFIG_MPSL_FEM_API_AVAILABLE=y
CONFIG_MPSL_FEM=y
CONFIG_MPSL_FEM_NRF21540_GPIO=y
# CONFIG_MPSL_FEM_NRF21540_GPIO_SPI is not set
CONFIG_MPSL_FEM_NRF21540_TX_GAIN_DB=10
CONFIG_MPSL_FEM_NRF21540_TX_GAIN_DB_POUTA=20
CONFIG_MPSL_FEM_NRF21540_TX_GAIN_DB_POUTB=10
CONFIG_MPSL_FEM_NRF21540_RX_GAIN_DB=13
# CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL is not set
# CONFIG_MPSL_FEM_POWER_MODEL is not set
CONFIG_MPSL_FEM_DEVICE_CONFIG_254=y
CONFIG_MPSL_FEM_INIT_PRIORITY=50
CONFIG_MPSL_THREAD_COOP_PRIO=6
CONFIG_MPSL_TIMESLOT_SESSION_COUNT=0
# CONFIG_MPSL_ASSERT_HANDLER is not set
# CONFIG_MPSL_TRIGGER_IPC_TASK_ON_RTC_START is not set
CONFIG_MPSL_LOW_PRIO_IRQN=26
# CONFIG_MPSL_PIN_DEBUG is not set
# end of Multiprotocol service layer (MPSL)

#
# Partition Manager
#
CONFIG_PARTITION_MANAGER_ENABLED=y
CONFIG_FLASH_MAP_CUSTOM=y
CONFIG_SRAM_BASE_ADDRESS=0x21000000

#
# Zephyr subsystem configurations
#
# end of Zephyr subsystem configurations

#
# NCS subsystem configurations
#
# CONFIG_PM_SINGLE_IMAGE is not set
CONFIG_PM_EXTERNAL_FLASH_BASE=0
CONFIG_PM_EXTERNAL_FLASH_PATH=""
CONFIG_PM_EXTERNAL_FLASH_SIZE_BITS=0
# CONFIG_PM_OVERRIDE_EXTERNAL_DRIVER_CHECK is not set
CONFIG_PM_SRAM_BASE=0x21000000
CONFIG_PM_SRAM_SIZE=0x10000
# end of Partition Manager

#
# nRF RPC (Remote Procedure Call) library
#
# end of nRF RPC (Remote Procedure Call) library

#
# Full Modem Firmware Update Management(FMFU)
#
# end of Full Modem Firmware Update Management(FMFU)

#
# SUIT-based Firmware Update Management
#
CONFIG_MGMT_SUITFU_TRIGGER_UPDATE_RESET_DELAY_MS=100
CONFIG_MGMT_SUITFU_AUTO_REGISTER_HANDLERS=y
CONFIG_MGMT_SUITFU_GRP_IMG=y
CONFIG_MGMT_SUITFU_IMAGE_NUMBER=0
# CONFIG_MGMT_SUITFU_GRP_SUIT is not set
# end of SUIT-based Firmware Update Management

# CONFIG_CAF is not set

#
# Nordic IEEE 802.15.4
#
# end of Nordic IEEE 802.15.4

# CONFIG_DM_MODULE is not set

#
# nRF Security
#
# CONFIG_NORDIC_SECURITY_BACKEND is not set
# CONFIG_NRF_SECURITY is not set
# CONFIG_PSA_WANT_GENERATE_RANDOM is not set
# CONFIG_PSA_WANT_ALG_CTR_DRBG is not set
# CONFIG_PSA_WANT_ALG_HMAC_DRBG is not set
# CONFIG_PSA_WANT_KEY_TYPE_DERIVE is not set
# CONFIG_PSA_WANT_KEY_TYPE_RAW_DATA is not set
# CONFIG_PSA_WANT_KEY_TYPE_HMAC is not set
# CONFIG_PSA_WANT_KEY_TYPE_PASSWORD is not set
# CONFIG_PSA_WANT_KEY_TYPE_PASSWORD_HASH is not set
# CONFIG_PSA_WANT_KEY_TYPE_PEPPER is not set
# CONFIG_PSA_WANT_KEY_TYPE_AES is not set
# CONFIG_PSA_WANT_KEY_TYPE_ARIA is not set
# CONFIG_PSA_WANT_KEY_TYPE_DES is not set
# CONFIG_PSA_WANT_KEY_TYPE_CAMELLIA is not set
# CONFIG_PSA_WANT_KEY_TYPE_SM4 is not set
# CONFIG_PSA_WANT_KEY_TYPE_ARC4 is not set
# CONFIG_PSA_WANT_KEY_TYPE_ECC_KEY_PAIR is not set
# CONFIG_PSA_WANT_KEY_TYPE_ECC_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_KEY_TYPE_ECC_KEY_PAIR_IMPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_ECC_KEY_PAIR_EXPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_ECC_KEY_PAIR_GENERATE is not set
# CONFIG_PSA_WANT_KEY_TYPE_ECC_KEY_PAIR_DERIVE is not set
# CONFIG_PSA_WANT_KEY_TYPE_RSA_KEY_PAIR is not set
# CONFIG_PSA_WANT_KEY_TYPE_RSA_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_KEY_TYPE_RSA_KEY_PAIR_IMPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_RSA_KEY_PAIR_EXPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_RSA_KEY_PAIR_GENERATE is not set
# CONFIG_PSA_WANT_KEY_TYPE_DH_KEY_PAIR is not set
# CONFIG_PSA_WANT_KEY_TYPE_DH_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_KEY_TYPE_SPAKE2P_KEY_PAIR_IMPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_SPAKE2P_KEY_PAIR_EXPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_SPAKE2P_KEY_PAIR_DERIVE is not set
# CONFIG_PSA_WANT_KEY_TYPE_SPAKE2P_KEY_PAIR is not set
# CONFIG_PSA_WANT_KEY_TYPE_SPAKE2P_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_KEY_TYPE_SRP_KEY_PAIR_IMPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_SRP_KEY_PAIR_EXPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_SRP_KEY_PAIR_DERIVE is not set
# CONFIG_PSA_WANT_KEY_TYPE_SRP_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_KEY_TYPE_SRP_KEY_PAIR is not set
# CONFIG_PSA_WANT_ALG_CCM is not set
# CONFIG_PSA_WANT_ALG_GCM is not set
# CONFIG_PSA_WANT_ALG_CHACHA20_POLY1305 is not set
# CONFIG_PSA_WANT_ALG_CBC_MAC is not set
# CONFIG_PSA_WANT_ALG_CMAC is not set
# CONFIG_PSA_WANT_ALG_HMAC is not set
# CONFIG_PSA_WANT_ALG_SHA_1 is not set
# CONFIG_PSA_WANT_ALG_SHA_224 is not set
# CONFIG_PSA_WANT_ALG_SHA_384 is not set
# CONFIG_PSA_WANT_ALG_SHA_512 is not set
# CONFIG_PSA_WANT_ALG_SHA_512_224 is not set
# CONFIG_PSA_WANT_ALG_SHA_512_256 is not set
# CONFIG_PSA_WANT_ALG_SHA3_224 is not set
# CONFIG_PSA_WANT_ALG_SHA3_256 is not set
# CONFIG_PSA_WANT_ALG_SHA3_384 is not set
# CONFIG_PSA_WANT_ALG_SHA3_512 is not set
# CONFIG_PSA_WANT_ALG_SM3 is not set
# CONFIG_PSA_WANT_ALG_SHAKE256_512 is not set
# CONFIG_PSA_WANT_ALG_RIPEMD160 is not set
# CONFIG_PSA_WANT_ALG_MD2 is not set
# CONFIG_PSA_WANT_ALG_MD4 is not set
# CONFIG_PSA_WANT_ALG_MD5 is not set
# CONFIG_PSA_WANT_ALG_ECB_NO_PADDING is not set
# CONFIG_PSA_WANT_ALG_CBC_NO_PADDING is not set
# CONFIG_PSA_WANT_ALG_CBC_PKCS7 is not set
# CONFIG_PSA_WANT_ALG_CFB is not set
# CONFIG_PSA_WANT_ALG_CTR is not set
# CONFIG_PSA_WANT_ALG_OFB is not set
# CONFIG_PSA_WANT_ALG_XTS is not set
# CONFIG_PSA_WANT_ALG_CCM_STAR_NO_TAG is not set
# CONFIG_PSA_WANT_ALG_STREAM_CIPHER is not set
# CONFIG_PSA_WANT_ALG_ECDH is not set
# CONFIG_PSA_WANT_ALG_FFDH is not set
# CONFIG_PSA_WANT_ALG_HKDF_EXTRACT is not set
# CONFIG_PSA_WANT_ALG_HKDF_EXPAND is not set
# CONFIG_PSA_WANT_ALG_ECDSA is not set
# CONFIG_PSA_WANT_ALG_ECDSA_ANY is not set
# CONFIG_PSA_WANT_ALG_DETERMINISTIC_ECDSA is not set
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_160 is not set
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_192 is not set
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_224 is not set
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_256 is not set
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_320 is not set
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_384 is not set
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_512 is not set
# CONFIG_PSA_WANT_ECC_MONTGOMERY_255 is not set
# CONFIG_PSA_WANT_ECC_MONTGOMERY_448 is not set
# CONFIG_PSA_WANT_ECC_TWISTED_EDWARDS_255 is not set
# CONFIG_PSA_WANT_ECC_TWISTED_EDWARDS_448 is not set
# CONFIG_PSA_WANT_ECC_SECP_K1_192 is not set
# CONFIG_PSA_WANT_ECC_SECP_K1_224 is not set
# CONFIG_PSA_WANT_ECC_SECP_K1_256 is not set
# CONFIG_PSA_WANT_ECC_SECP_R1_192 is not set
# CONFIG_PSA_WANT_ECC_SECP_R1_224 is not set
# CONFIG_PSA_WANT_ECC_SECP_R1_256 is not set
# CONFIG_PSA_WANT_ECC_SECP_R1_384 is not set
# CONFIG_PSA_WANT_ECC_SECP_R1_521 is not set
# CONFIG_PSA_WANT_ECC_SECP_R2_160 is not set
# CONFIG_PSA_WANT_ECC_SECT_K1_163 is not set
# CONFIG_PSA_WANT_ECC_SECT_K1_233 is not set
# CONFIG_PSA_WANT_ECC_SECT_K1_239 is not set
# CONFIG_PSA_WANT_ECC_SECT_K1_283 is not set
# CONFIG_PSA_WANT_ECC_SECT_K1_409 is not set
# CONFIG_PSA_WANT_ECC_SECT_K1_571 is not set
# CONFIG_PSA_WANT_ECC_SECT_R1_163 is not set
# CONFIG_PSA_WANT_ECC_SECT_R1_233 is not set
# CONFIG_PSA_WANT_ECC_SECT_R1_283 is not set
# CONFIG_PSA_WANT_ECC_SECT_R1_409 is not set
# CONFIG_PSA_WANT_ECC_SECT_R1_571 is not set
# CONFIG_PSA_WANT_ECC_SECT_R2_163 is not set
# CONFIG_PSA_WANT_ECC_FRP_V1_256 is not set
# CONFIG_PSA_WANT_ALG_RSA_OAEP is not set
# CONFIG_PSA_WANT_ALG_RSA_PKCS1V15_CRYPT is not set
# CONFIG_PSA_WANT_ALG_RSA_PKCS1V15_SIGN is not set
# CONFIG_PSA_WANT_ALG_RSA_PKCS1V15_SIGN_RAW is not set
# CONFIG_PSA_WANT_ALG_RSA_PSS is not set
# CONFIG_PSA_WANT_ALG_RSA_PSS_ANY_SALT is not set
# CONFIG_PSA_WANT_ALG_JPAKE is not set
# CONFIG_PSA_WANT_ALG_SPAKE2P_HMAC is not set
# CONFIG_PSA_WANT_ALG_SPAKE2P_CMAC is not set
# CONFIG_PSA_WANT_ALG_SPAKE2P_MATTER is not set
# CONFIG_PSA_WANT_ALG_SRP_6 is not set
# CONFIG_PSA_WANT_ALG_SRP_PASSWORD_HASH is not set
# CONFIG_PSA_WANT_ALG_PURE_EDDSA is not set
# CONFIG_PSA_WANT_ALG_ED25519PH is not set
# CONFIG_PSA_WANT_ALG_ED448PH is not set
# end of nRF Security

# CONFIG_NET_CORE_MONITOR is not set

#
# Audio Module
#
# CONFIG_AUDIO_MODULE_TEST is not set
CONFIG_AUDIO_MODULE_NAME_SIZE=20
# end of Audio Module

# CONFIG_TRUSTED_STORAGE is not set

#
# SUIT provisioning
#
# CONFIG_SUIT_MPI_GENERATE is not set
# end of SUIT provisioning

# CONFIG_SUIT is not set
# CONFIG_DULT is not set
# end of Subsystems

# CONFIG_WPA_SUPP is not set
CONFIG_COMMON_LIBC_MALLOC_ARENA_SIZE=-1
CONFIG_POSIX_MAX_FDS=4
# CONFIG_WFA_QT_CONTROL_APP is not set
CONFIG_WFA_QT_THREAD_STACK_SIZE=4096
CONFIG_WFA_QT_REBOOT_TIMEOUT_MS=1000
CONFIG_WFA_QT_DEFAULT_INTERFACE="nordic_wlan0"
CONFIG_WPAS_READY_TIMEOUT_MS=10000

#
# Libraries
#

#
# Binary libraries
#
# end of Binary libraries

# CONFIG_AT_MONITOR is not set
# CONFIG_LTE_LINK_CONTROL is not set
CONFIG_NRF_ACL_FLASH_REGION_SIZE=0x800
CONFIG_FPROTECT_BLOCK_SIZE=0x800
# CONFIG_FPROTECT is not set
# CONFIG_AT_CMD_CUSTOM is not set
# CONFIG_DK_LIBRARY is not set
# CONFIG_AT_CMD_PARSER is not set
# CONFIG_MODEM_INFO is not set
CONFIG_MULTITHREADING_LOCK=y
# CONFIG_RESET_ON_FATAL_ERROR is not set
# CONFIG_SMS is not set
# CONFIG_DATE_TIME is not set
# CONFIG_HW_ID_LIBRARY is not set
# CONFIG_WAVE_GEN_LIB is not set
CONFIG_HW_UNIQUE_KEY_PARTITION_SIZE=0x800
# CONFIG_MODEM_JWT is not set
# CONFIG_LOCATION is not set
# CONFIG_QOS is not set
# CONFIG_SFLOAT is not set
# CONFIG_CONTIN_ARRAY is not set
# CONFIG_PCM_MIX is not set
# CONFIG_TONE is not set
# CONFIG_PSCM is not set
# CONFIG_DATA_FIFO is not set
# CONFIG_FEM_AL_LIB is not set
# CONFIG_SAMPLE_RATE_CONVERTER is not set
CONFIG_NCS_BOOT_BANNER=y
CONFIG_NCS_NCS_BOOT_BANNER_STRING="nRF Connect SDK"
CONFIG_NCS_ZEPHYR_BOOT_BANNER_STRING="Zephyr OS"
# end of Libraries

#
# Device Drivers
#
# CONFIG_BT_DRIVER_QUIRK_NO_AUTO_DLE is not set
# CONFIG_ETH_RTT is not set
# CONFIG_SENSOR is not set
# CONFIG_NRF_SW_LPUART is not set
CONFIG_NRFX_GPIOTE_NUM_OF_EVT_HANDLERS=1
# CONFIG_IPC_UART is not set
# CONFIG_FLASH_RPC is not set
CONFIG_CLOCK_CONTROL_MPSL=y
CONFIG_SOC_FLASH_NRF_RADIO_SYNC_MPSL_TIMESLOT_SESSION_COUNT=0
# end of Device Drivers

#
# External libraries
#
# end of External libraries

#
# Test
#
CONFIG_ZTEST_MULTICORE_DEFAULT_SETTINGS=y
# CONFIG_UNITY is not set

#
# Mocks
#
# CONFIG_MOCK_NRF_MODEM_AT is not set
# end of Mocks
# end of Test
# end of Nordic nRF Connect

CONFIG_ZEPHYR_NRF_MODULE=y
# end of nrf (C:/ncs/v2.7.0/nrf)

#
# mcuboot (C:/ncs/v2.7.0/bootloader/mcuboot)
#

#
# MCUboot
#
CONFIG_BOOT_SIGNATURE_KEY_FILE=""
CONFIG_DT_FLASH_WRITE_BLOCK_SIZE=4
# end of MCUboot

CONFIG_ZEPHYR_MCUBOOT_MODULE=y
# end of mcuboot (C:/ncs/v2.7.0/bootloader/mcuboot)

#
# mbedtls (C:/ncs/v2.7.0/modules/crypto/mbedtls)
#
CONFIG_ZEPHYR_MBEDTLS_MODULE=y

#
# PSA RNG support
#
# end of PSA RNG support

#
# PSA key type support
#
# end of PSA key type support

#
# PSA AEAD support
#
# end of PSA AEAD support

#
# PSA MAC support
#
# end of PSA MAC support

#
# PSA Hash support
#
# end of PSA Hash support

#
# PSA Cipher support
#
# end of PSA Cipher support

#
# PSA Key agreement support
#
# end of PSA Key agreement support

#
# PSA Key derivation support
#
# end of PSA Key derivation support

#
# PSA Asymmetric support
#

#
# Elliptic Curve type support
#
# end of Elliptic Curve type support
# end of PSA Asymmetric support
# end of mbedtls (C:/ncs/v2.7.0/modules/crypto/mbedtls)

#
# oberon-psa-crypto (C:/ncs/v2.7.0/modules/crypto/oberon-psa-crypto)
#
CONFIG_ZEPHYR_OBERON_PSA_CRYPTO_MODULE=y
# end of oberon-psa-crypto (C:/ncs/v2.7.0/modules/crypto/oberon-psa-crypto)

#
# trusted-firmware-m (C:/ncs/v2.7.0/modules/tee/tf-m/trusted-firmware-m)
#
# CONFIG_BOOTLOADER_MCUBOOT is not set
CONFIG_ZEPHYR_TRUSTED_FIRMWARE_M_MODULE=y
# end of trusted-firmware-m (C:/ncs/v2.7.0/modules/tee/tf-m/trusted-firmware-m)

CONFIG_ZEPHYR_PSA_ARCH_TESTS_MODULE=y
CONFIG_ZEPHYR_SOC_HWMV1_MODULE=y

#
# cjson (C:/ncs/v2.7.0/modules/lib/cjson)
#
# CONFIG_CJSON_LIB is not set
CONFIG_ZEPHYR_CJSON_MODULE=y
# end of cjson (C:/ncs/v2.7.0/modules/lib/cjson)

#
# azure-sdk-for-c (C:/ncs/v2.7.0/modules/lib/azure-sdk-for-c)
#
# CONFIG_AZURE_SDK is not set
CONFIG_ZEPHYR_AZURE_SDK_FOR_C_MODULE=y
# end of azure-sdk-for-c (C:/ncs/v2.7.0/modules/lib/azure-sdk-for-c)

#
# cirrus-logic (C:/ncs/v2.7.0/modules/hal/cirrus-logic)
#
# CONFIG_HW_CODEC_CIRRUS_LOGIC is not set
CONFIG_ZEPHYR_CIRRUS_LOGIC_MODULE=y
# end of cirrus-logic (C:/ncs/v2.7.0/modules/hal/cirrus-logic)

#
# openthread (C:/ncs/v2.7.0/modules/lib/openthread)
#
# CONFIG_OPENTHREAD is not set
CONFIG_ZEPHYR_OPENTHREAD_MODULE=y
# end of openthread (C:/ncs/v2.7.0/modules/lib/openthread)

#
# suit-generator (C:/ncs/v2.7.0/modules/lib/suit-generator)
#
CONFIG_SUIT_ENVELOPE_TEMPLATE=""
CONFIG_SUIT_ENVELOPE_TARGET=""
CONFIG_SUIT_ENVELOPE_OUTPUT_ARTIFACT="merged.hex"
CONFIG_SUIT_ENVELOPE_OUTPUT_MPI_MERGE=y
# CONFIG_SUIT_LOCAL_ENVELOPE_GENERATE is not set
CONFIG_ZEPHYR_SUIT_GENERATOR_MODULE=y
# end of suit-generator (C:/ncs/v2.7.0/modules/lib/suit-generator)

#
# suit-processor (C:/ncs/v2.7.0/modules/lib/suit-processor)
#
# CONFIG_SUIT_PROCESSOR is not set
CONFIG_SUIT_PLATFORM_DRY_RUN_SUPPORT=y
CONFIG_ZEPHYR_SUIT_PROCESSOR_MODULE=y
# end of suit-processor (C:/ncs/v2.7.0/modules/lib/suit-processor)

#
# memfault-firmware-sdk (C:/ncs/v2.7.0/modules/lib/memfault-firmware-sdk)
#
# CONFIG_MEMFAULT is not set
CONFIG_ZEPHYR_MEMFAULT_FIRMWARE_SDK_MODULE=y
# end of memfault-firmware-sdk (C:/ncs/v2.7.0/modules/lib/memfault-firmware-sdk)

#
# coremark (C:/ncs/v2.7.0/modules/benchmark/coremark)
#
# CONFIG_COREMARK is not set
CONFIG_ZEPHYR_COREMARK_MODULE=y
# end of coremark (C:/ncs/v2.7.0/modules/benchmark/coremark)

#
# canopennode (C:/ncs/v2.7.0/modules/lib/canopennode)
#
CONFIG_ZEPHYR_CANOPENNODE_MODULE=y
# end of canopennode (C:/ncs/v2.7.0/modules/lib/canopennode)

#
# chre (C:/ncs/v2.7.0/modules/lib/chre)
#
CONFIG_ZEPHYR_CHRE_MODULE=y
# CONFIG_CHRE is not set
# end of chre (C:/ncs/v2.7.0/modules/lib/chre)

#
# lz4 (C:/ncs/v2.7.0/modules/lib/lz4)
#
CONFIG_ZEPHYR_LZ4_MODULE=y
# CONFIG_LZ4 is not set
# end of lz4 (C:/ncs/v2.7.0/modules/lib/lz4)

#
# nanopb (C:/ncs/v2.7.0/modules/lib/nanopb)
#
CONFIG_ZEPHYR_NANOPB_MODULE=y
# CONFIG_NANOPB is not set
# end of nanopb (C:/ncs/v2.7.0/modules/lib/nanopb)

CONFIG_ZEPHYR_TF_M_TESTS_MODULE=y

#
# zscilib (C:/ncs/v2.7.0/modules/lib/zscilib)
#
# CONFIG_ZSL is not set
CONFIG_ZEPHYR_ZSCILIB_MODULE=y
# end of zscilib (C:/ncs/v2.7.0/modules/lib/zscilib)

#
# cmsis (C:/ncs/v2.7.0/modules/hal/cmsis)
#
CONFIG_ZEPHYR_CMSIS_MODULE=y
CONFIG_HAS_CMSIS_CORE=y
CONFIG_HAS_CMSIS_CORE_M=y
# CONFIG_CMSIS_M_CHECK_DEVICE_DEFINES is not set
# end of cmsis (C:/ncs/v2.7.0/modules/hal/cmsis)

#
# cmsis-dsp (C:/ncs/v2.7.0/modules/lib/cmsis-dsp)
#
CONFIG_ZEPHYR_CMSIS_DSP_MODULE=y
# CONFIG_CMSIS_DSP is not set
# end of cmsis-dsp (C:/ncs/v2.7.0/modules/lib/cmsis-dsp)

#
# cmsis-nn (C:/ncs/v2.7.0/modules/lib/cmsis-nn)
#
CONFIG_ZEPHYR_CMSIS_NN_MODULE=y
# CONFIG_CMSIS_NN is not set
# end of cmsis-nn (C:/ncs/v2.7.0/modules/lib/cmsis-nn)

#
# fatfs (C:/ncs/v2.7.0/modules/fs/fatfs)
#
CONFIG_ZEPHYR_FATFS_MODULE=y
# end of fatfs (C:/ncs/v2.7.0/modules/fs/fatfs)

#
# hal_nordic (C:/ncs/v2.7.0/modules/hal/nordic)
#
CONFIG_ZEPHYR_HAL_NORDIC_MODULE=y
CONFIG_HAS_NORDIC_DRIVERS=y

#
# Nordic drivers
#
# CONFIG_NRF_802154_SOURCE_HAL_NORDIC is not set
# CONFIG_NRF_802154_RADIO_DRIVER is not set
# CONFIG_NRF_802154_SER_RADIO is not set
# end of Nordic drivers

CONFIG_HAS_NRFX=y

#
# nrfx drivers
#
CONFIG_MPSL=y
# CONFIG_NRFX_CLOCK is not set
CONFIG_NRFX_DPPI=y
# CONFIG_NRFX_EGU0 is not set
CONFIG_NRFX_GPIOTE=y
CONFIG_NRFX_GPIOTE0=y
CONFIG_NRFX_IPC=y
# CONFIG_NRFX_NVMC is not set
# CONFIG_NRFX_POWER is not set
# CONFIG_NRFX_RNG is not set
# CONFIG_NRFX_RTC0 is not set
# CONFIG_NRFX_RTC1 is not set
# CONFIG_NRFX_SPIM0 is not set
# CONFIG_NRFX_SYSTICK is not set
# CONFIG_NRFX_TEMP is not set
# CONFIG_NRFX_TIMER0 is not set
# CONFIG_NRFX_TIMER1 is not set
# CONFIG_NRFX_TIMER2 is not set
# CONFIG_NRFX_TWIM0 is not set
# CONFIG_NRFX_UARTE0 is not set
# CONFIG_NRFX_WDT0 is not set

#
# Peripheral Resource Sharing module
#
# CONFIG_NRFX_PRS_BOX_0 is not set
# CONFIG_NRFX_PRS_BOX_1 is not set
# CONFIG_NRFX_PRS_BOX_2 is not set
# CONFIG_NRFX_PRS_BOX_3 is not set
# CONFIG_NRFX_PRS_BOX_4 is not set
# end of Peripheral Resource Sharing module
# end of nrfx drivers
# end of hal_nordic (C:/ncs/v2.7.0/modules/hal/nordic)

#
# hal_st (C:/ncs/v2.7.0/modules/hal/st)
#
CONFIG_ZEPHYR_HAL_ST_MODULE=y
# end of hal_st (C:/ncs/v2.7.0/modules/hal/st)

CONFIG_ZEPHYR_HAL_WURTHELEKTRONIK_MODULE=y
CONFIG_ZEPHYR_LIBMETAL_MODULE=y

#
# liblc3 (C:/ncs/v2.7.0/modules/lib/liblc3)
#
CONFIG_ZEPHYR_LIBLC3_MODULE=y
# end of liblc3 (C:/ncs/v2.7.0/modules/lib/liblc3)

#
# littlefs (C:/ncs/v2.7.0/modules/fs/littlefs)
#
CONFIG_ZEPHYR_LITTLEFS_MODULE=y
# end of littlefs (C:/ncs/v2.7.0/modules/fs/littlefs)

#
# loramac-node (C:/ncs/v2.7.0/modules/lib/loramac-node)
#
CONFIG_ZEPHYR_LORAMAC_NODE_MODULE=y
# CONFIG_HAS_SEMTECH_RADIO_DRIVERS is not set
# end of loramac-node (C:/ncs/v2.7.0/modules/lib/loramac-node)

#
# lvgl (C:/ncs/v2.7.0/modules/lib/gui/lvgl)
#
CONFIG_ZEPHYR_LVGL_MODULE=y
# end of lvgl (C:/ncs/v2.7.0/modules/lib/gui/lvgl)

CONFIG_ZEPHYR_MIPI_SYS_T_MODULE=y
CONFIG_ZEPHYR_NRF_HW_MODELS_MODULE=y
CONFIG_ZEPHYR_OPEN_AMP_MODULE=y

#
# picolibc (C:/ncs/v2.7.0/modules/lib/picolibc)
#
# CONFIG_PICOLIBC_MODULE is not set
CONFIG_ZEPHYR_PICOLIBC_MODULE=y
# end of picolibc (C:/ncs/v2.7.0/modules/lib/picolibc)

#
# segger (C:/ncs/v2.7.0/modules/debug/segger)
#
CONFIG_ZEPHYR_SEGGER_MODULE=y
CONFIG_HAS_SEGGER_RTT=y
# CONFIG_USE_SEGGER_RTT is not set
# end of segger (C:/ncs/v2.7.0/modules/debug/segger)

CONFIG_ZEPHYR_TINYCRYPT_MODULE=y

#
# uoscore-uedhoc (C:/ncs/v2.7.0/modules/lib/uoscore-uedhoc)
#
CONFIG_ZEPHYR_UOSCORE_UEDHOC_MODULE=y
# end of uoscore-uedhoc (C:/ncs/v2.7.0/modules/lib/uoscore-uedhoc)

#
# zcbor (C:/ncs/v2.7.0/modules/lib/zcbor)
#
CONFIG_ZEPHYR_ZCBOR_MODULE=y
# CONFIG_ZCBOR is not set
# end of zcbor (C:/ncs/v2.7.0/modules/lib/zcbor)

#
# nrfxlib (C:/ncs/v2.7.0/nrfxlib)
#

#
# Nordic nrfxlib
#

#
# nrf_modem (Modem library)
#
# end of nrf_modem (Modem library)

CONFIG_NRF_MODEM_SHMEM_CTRL_SIZE=0x4e8
# CONFIG_NFC_T2T_NRFXLIB is not set
# CONFIG_NFC_T4T_NRFXLIB is not set
CONFIG_MPSL_BUILD_TYPE_LIB=y
CONFIG_MPSL_LIB_DIR="cortex-m33+nodsp"
CONFIG_MPSL_LIB_FLOAT_ABI_DIR="soft-float"

#
# Crypto libraries for nRF5x SOCs.
#
CONFIG_NRFXLIB_CRYPTO=y
CONFIG_NRF_OBERON=y
# CONFIG_NRF_CC310_BL is not set
# end of Crypto libraries for nRF5x SOCs.

# CONFIG_NRF_RPC is not set
CONFIG_NRF_802154_SOURCE_NRFXLIB=y
# CONFIG_GZLL is not set
# CONFIG_NRF_DM is not set
# CONFIG_NRF_FUEL_GAUGE is not set
# end of Nordic nrfxlib

CONFIG_ZEPHYR_NRFXLIB_MODULE=y
# end of nrfxlib (C:/ncs/v2.7.0/nrfxlib)

#
# connectedhomeip (C:/ncs/v2.7.0/modules/lib/matter)
#
# CONFIG_CHIP is not set
CONFIG_ZEPHYR_CONNECTEDHOMEIP_MODULE=y
# end of connectedhomeip (C:/ncs/v2.7.0/modules/lib/matter)

CONFIG_LIBMETAL=y
CONFIG_LIBMETAL_SRC_PATH="libmetal"
# CONFIG_LVGL is not set
# CONFIG_HAS_MEC_HAL is not set
# CONFIG_HAS_MPFS_HAL is not set
# CONFIG_HAS_MEC5_HAL is not set
CONFIG_OPENAMP=y
CONFIG_OPENAMP_SRC_PATH="open-amp"
CONFIG_OPENAMP_MASTER=y
CONFIG_OPENAMP_SLAVE=y
# CONFIG_MIPI_SYST_LIB is not set
# CONFIG_HAS_TELINK_DRIVERS is not set
# CONFIG_TINYCRYPT_CTR_PRNG is not set
# CONFIG_TINYCRYPT_SHA256 is not set
# CONFIG_TINYCRYPT_ECC_DH is not set
# CONFIG_TINYCRYPT_ECC_DSA is not set
CONFIG_TINYCRYPT_AES=y
# CONFIG_TINYCRYPT_AES_CBC is not set
# CONFIG_TINYCRYPT_AES_CTR is not set
# CONFIG_TINYCRYPT_AES_CCM is not set
# CONFIG_TINYCRYPT_AES_CMAC is not set
# CONFIG_MCUBOOT_BOOTUTIL_LIB is not set
# CONFIG_WIFI_NM_WPA_SUPPLICANT is not set

#
# Unavailable modules, please install those via the project manifest.
#

#
# hal_gigadevice module not available.
#

#
# Trusted-firmware-a module not available.
#

#
# THRIFT module not available.
#
# CONFIG_ACPI is not set
# end of Modules

CONFIG_BOARD="nrf5340dk"
CONFIG_BOARD_REVISION=""
CONFIG_BOARD_TARGET="nrf5340dk/nrf5340/cpunet"
# CONFIG_NET_DRIVERS is not set
CONFIG_BOARD_NRF5340DK=y
CONFIG_BOARD_NRF5340DK_NRF5340_CPUNET=y
CONFIG_BOARD_QUALIFIERS="nrf5340/cpunet"

#
# Board Options
#
CONFIG_DOMAIN_CPUAPP_BOARD="nrf5340dk/nrf5340/cpuapp"
# end of Board Options

#
# Hardware Configuration
#
CONFIG_SOC_FAMILY="nordic_nrf"
CONFIG_SOC_FAMILY_NORDIC_NRF=y
CONFIG_SOC_SERIES_NRF53X=y
CONFIG_SOC_NRF5340_CPUNET=y
CONFIG_SOC_NRF5340_CPUNET_QKAA=y
# CONFIG_MFD is not set
# CONFIG_BUILD_OUTPUT_INFO_HEADER is not set
CONFIG_HAS_HW_NRF_ACL=y
CONFIG_HAS_HW_NRF_CCM=y
CONFIG_HAS_HW_NRF_CCM_LFLEN_8BIT=y
CONFIG_HAS_HW_NRF_CCM_HEADERMASK=y
CONFIG_HAS_HW_NRF_CLOCK=y
CONFIG_HAS_HW_NRF_DPPIC=y
CONFIG_HAS_HW_NRF_ECB=y
CONFIG_HAS_HW_NRF_EGU0=y
CONFIG_HAS_HW_NRF_GPIO0=y
CONFIG_HAS_HW_NRF_GPIO1=y
CONFIG_HAS_HW_NRF_GPIOTE0=y
CONFIG_HAS_HW_NRF_IPC=y
CONFIG_HAS_HW_NRF_NVMC_PE=y
CONFIG_HAS_HW_NRF_POWER=y
CONFIG_HAS_HW_NRF_RADIO_BLE_2M=y
CONFIG_HAS_HW_NRF_RADIO_BLE_CODED=y
CONFIG_HAS_HW_NRF_RADIO_DFE=y
CONFIG_HAS_HW_NRF_RADIO_IEEE802154=y
CONFIG_HAS_HW_NRF_RNG=y
CONFIG_HAS_HW_NRF_SPIM0=y
CONFIG_HAS_HW_NRF_SWI0=y
CONFIG_HAS_HW_NRF_SWI1=y
CONFIG_HAS_HW_NRF_SWI2=y
CONFIG_HAS_HW_NRF_SWI3=y
CONFIG_HAS_HW_NRF_TEMP=y
CONFIG_HAS_HW_NRF_UARTE0=y
CONFIG_HAS_HW_NRF_VMC=y
CONFIG_HAS_HW_NRF_WDT0=y
CONFIG_SOC_NRF53_ANOMALY_160_WORKAROUND_NEEDED=y
CONFIG_SOC_NRF53_ANOMALY_160_WORKAROUND=y
CONFIG_SOC_NRF53_ANOMALY_168_WORKAROUND=y
CONFIG_SOC_NRF53_RTC_PRETICK=y
CONFIG_SOC_NRF53_RTC_PRETICK_IPC_CH_FROM_NET=10
CONFIG_SOC_NRF53_RTC_PRETICK_IPC_CH_TO_NET=11
CONFIG_NRF_ENABLE_CACHE=y
# CONFIG_NRF53_SYNC_RTC is not set
CONFIG_NRF_RTC_TIMER_USER_CHAN_COUNT=0
CONFIG_NRF_SOC_SECURE_SUPPORTED=y
CONFIG_NRF_APPROTECT_USE_UICR=y
# CONFIG_NRF_APPROTECT_LOCK is not set
# CONFIG_NRF_APPROTECT_USER_HANDLING is not set
# CONFIG_NRF_TRACE_PORT is not set
CONFIG_GPIO_INIT_PRIORITY=40
# end of Hardware Configuration

CONFIG_SOC_COMPATIBLE_NRF=y
CONFIG_SOC_COMPATIBLE_NRF53X=y
CONFIG_SOC_COMPATIBLE_NRF5340_CPUNET=y
CONFIG_ARCH="arm"
CONFIG_ARCH_HAS_SINGLE_THREAD_SUPPORT=y
# CONFIG_EXTRA_EXCEPTION_INFO is not set
CONFIG_CPU_CORTEX=y
CONFIG_KOBJECT_TEXT_AREA=256
CONFIG_ARM_MPU=y
CONFIG_ARM_MPU_REGION_MIN_ALIGN_AND_SIZE=32
# CONFIG_MPU_ALLOW_FLASH_WRITE is not set

#
# ARM Options
#
CONFIG_ARM_ON_ENTER_CPU_IDLE_HOOK=y
CONFIG_ARM_ON_ENTER_CPU_IDLE_PREPARE_HOOK=y
CONFIG_ARM_ON_EXIT_CPU_IDLE=y
CONFIG_CPU_CORTEX_M=y
# CONFIG_ARM_ZIMAGE_HEADER is not set
CONFIG_ISA_THUMB2=y
CONFIG_ASSEMBLER_ISA_THUMB2=y
CONFIG_COMPILER_ISA_THUMB2=y
CONFIG_STACK_ALIGN_DOUBLE_WORD=y
# CONFIG_RUNTIME_NMI is not set
CONFIG_FAULT_DUMP=2
CONFIG_BUILTIN_STACK_GUARD=y
CONFIG_ARM_STACK_PROTECTION=y
CONFIG_FP16=y
CONFIG_FP16_IEEE=y
# CONFIG_FP16_ALT is not set
CONFIG_CPU_CORTEX_M33=y
CONFIG_CPU_CORTEX_M_HAS_SYSTICK=y
CONFIG_CPU_CORTEX_M_HAS_DWT=y
CONFIG_CPU_CORTEX_M_HAS_BASEPRI=y
CONFIG_CPU_CORTEX_M_HAS_VTOR=y
CONFIG_CPU_CORTEX_M_HAS_SPLIM=y
CONFIG_CPU_CORTEX_M_HAS_PROGRAMMABLE_FAULT_PRIOS=y
CONFIG_CPU_CORTEX_M_HAS_CMSE=y
CONFIG_ARMV7_M_ARMV8_M_MAINLINE=y
CONFIG_ARMV8_M_MAINLINE=y

#
# ARM Cortex-M0/M0+/M1/M3/M4/M7/M23/M33/M55 options
#
CONFIG_ZERO_LATENCY_IRQS=y
CONFIG_ZERO_LATENCY_LEVELS=1
# CONFIG_SW_VECTOR_RELAY is not set
# CONFIG_CORTEX_M_DWT is not set
# CONFIG_CORTEX_M_DEBUG_MONITOR_HOOK is not set
# CONFIG_TRAP_UNALIGNED_ACCESS is not set
# end of ARM Cortex-M0/M0+/M1/M3/M4/M7/M23/M33/M55 options

CONFIG_NULL_POINTER_EXCEPTION_DETECTION_NONE=y
# CONFIG_NULL_POINTER_EXCEPTION_DETECTION_DWT is not set
# CONFIG_NULL_POINTER_EXCEPTION_DETECTION_MPU is not set
# CONFIG_MPU_STACK_GUARD is not set
# CONFIG_MPU_DISABLE_BACKGROUND_MAP is not set
# CONFIG_CUSTOM_SECTION_ALIGN is not set
CONFIG_CUSTOM_SECTION_MIN_ALIGN_SIZE=32
CONFIG_HAS_SWO=y
# end of ARM Options

CONFIG_ARM=y
CONFIG_ARCH_IS_SET=y

#
# General Architecture Options
#
# CONFIG_SEMIHOST is not set
CONFIG_LITTLE_ENDIAN=y
# CONFIG_USERSPACE is not set
CONFIG_KOBJECT_DATA_AREA_RESERVE_EXTRA_PERCENT=100
CONFIG_KOBJECT_RODATA_AREA_EXTRA_BYTES=16
CONFIG_GEN_PRIV_STACKS=y
# CONFIG_STACK_GROWS_UP is not set

#
# Interrupt Configuration
#
CONFIG_ISR_TABLES_LOCAL_DECLARATION_SUPPORTED=y
# CONFIG_ISR_TABLES_LOCAL_DECLARATION is not set
CONFIG_IRQ_VECTOR_TABLE_JUMP_BY_ADDRESS=y
# CONFIG_IRQ_VECTOR_TABLE_JUMP_BY_CODE is not set
CONFIG_EXCEPTION_DEBUG=y
# CONFIG_SIMPLIFIED_EXCEPTION_CODES is not set
# end of Interrupt Configuration
# end of General Architecture Options

CONFIG_ARCH_HAS_TIMING_FUNCTIONS=y
CONFIG_ARCH_HAS_STACK_PROTECTION=y
CONFIG_ARCH_HAS_USERSPACE=y
CONFIG_ARCH_HAS_EXECUTABLE_PAGE_BIT=y
CONFIG_ARCH_HAS_RAMFUNC_SUPPORT=y
CONFIG_ARCH_HAS_NESTED_EXCEPTION_DETECTION=y
CONFIG_ARCH_SUPPORTS_COREDUMP=y
CONFIG_ARCH_SUPPORTS_ARCH_HW_INIT=y
CONFIG_ARCH_SUPPORTS_ROM_START=y
CONFIG_ARCH_HAS_EXTRA_EXCEPTION_INFO=y
CONFIG_ARCH_HAS_THREAD_LOCAL_STORAGE=y
CONFIG_ARCH_HAS_SUSPEND_TO_RAM=y
CONFIG_ARCH_HAS_THREAD_ABORT=y
CONFIG_ARCH_HAS_CODE_DATA_RELOCATION=y
CONFIG_CPU_HAS_MPU=y
CONFIG_MPU=y
CONFIG_MPU_REQUIRES_NON_OVERLAPPING_REGIONS=y
CONFIG_MPU_GAP_FILLING=y
CONFIG_SRAM_REGION_PERMISSIONS=y

#
# DSP Options
#
# end of DSP Options

#
# Floating Point Options
#
# end of Floating Point Options

#
# Cache Options
#
# end of Cache Options

CONFIG_TOOLCHAIN_HAS_BUILTIN_FFS=y
# CONFIG_ARCH_CPU_IDLE_CUSTOM is not set

#
# General Kernel Options
#
CONFIG_MULTITHREADING=y
CONFIG_NUM_COOP_PRIORITIES=16
CONFIG_NUM_PREEMPT_PRIORITIES=15
CONFIG_MAIN_THREAD_PRIORITY=0
CONFIG_COOP_ENABLED=y
CONFIG_PREEMPT_ENABLED=y
CONFIG_PRIORITY_CEILING=-127
# CONFIG_SCHED_DEADLINE is not set
CONFIG_THREAD_STACK_INFO=y
# CONFIG_THREAD_CUSTOM_DATA is not set
# CONFIG_DYNAMIC_THREAD is not set
CONFIG_SCHED_DUMB=y
# CONFIG_SCHED_SCALABLE is not set
# CONFIG_SCHED_MULTIQ is not set
# CONFIG_WAITQ_SCALABLE is not set
CONFIG_WAITQ_DUMB=y

#
# Misc Kernel related options
#
CONFIG_LIBC_ERRNO=y
CONFIG_ERRNO=y
CONFIG_CURRENT_THREAD_USE_TLS=y
# end of Misc Kernel related options

#
# Kernel Debugging and Metrics
#
CONFIG_BOOT_DELAY=0
# CONFIG_THREAD_MONITOR is not set
# CONFIG_THREAD_NAME is not set
# CONFIG_THREAD_RUNTIME_STATS is not set
# end of Kernel Debugging and Metrics

# CONFIG_OBJ_CORE is not set

#
# System Work Queue Options
#
# CONFIG_SYSTEM_WORKQUEUE_NO_YIELD is not set
# end of System Work Queue Options

#
# Barrier Operations
#
CONFIG_BARRIER_OPERATIONS_ARCH=y
# end of Barrier Operations

#
# Atomic Operations
#
CONFIG_ATOMIC_OPERATIONS_BUILTIN=y
# end of Atomic Operations

#
# Timer API Options
#
CONFIG_TIMESLICING=y
CONFIG_TIMESLICE_SIZE=0
CONFIG_TIMESLICE_PRIORITY=0
# CONFIG_TIMESLICE_PER_THREAD is not set
# end of Timer API Options

#
# Other Kernel Object Options
#
CONFIG_POLL=y
# CONFIG_MEM_SLAB_TRACE_MAX_UTILIZATION is not set
CONFIG_NUM_MBOX_ASYNC_MSGS=10
# CONFIG_EVENTS is not set
# CONFIG_PIPES is not set
CONFIG_KERNEL_MEM_POOL=y
# CONFIG_HEAP_MEM_POOL_IGNORE_MIN is not set
# end of Other Kernel Object Options

CONFIG_ARCH_HAS_CUSTOM_SWAP_TO_MAIN=y
CONFIG_SWAP_NONATOMIC=y
CONFIG_SYS_CLOCK_EXISTS=y
CONFIG_TIMEOUT_64BIT=y
CONFIG_SYS_CLOCK_MAX_TIMEOUT_DAYS=365

#
# Security Options
#
# CONFIG_STACK_CANARIES is not set
CONFIG_STACK_POINTER_RANDOM=0
# end of Security Options

#
# Memory Domains
#
CONFIG_ARCH_MEM_DOMAIN_SUPPORTS_ISOLATED_STACKS=y
CONFIG_MEM_DOMAIN_ISOLATED_STACKS=y
# end of Memory Domains

#
# SMP Options
#
CONFIG_MP_NUM_CPUS=1
# CONFIG_TICKET_SPINLOCKS is not set
# end of SMP Options

CONFIG_TOOLCHAIN_SUPPORTS_THREAD_LOCAL_STORAGE=y
CONFIG_THREAD_LOCAL_STORAGE=y
# end of General Kernel Options

#
# Device Options
#
# CONFIG_DEVICE_DEPS is not set
# CONFIG_DEVICE_MUTABLE is not set
# end of Device Options

#
# Initialization Priorities
#
CONFIG_KERNEL_INIT_PRIORITY_OBJECTS=30
CONFIG_KERNEL_INIT_PRIORITY_DEFAULT=40
CONFIG_KERNEL_INIT_PRIORITY_DEVICE=50
CONFIG_APPLICATION_INIT_PRIORITY=90
# end of Initialization Priorities

#
# Virtual Memory Support
#
# end of Virtual Memory Support

#
# Device Drivers
#
# CONFIG_ADC is not set
# CONFIG_AUDIO is not set
# CONFIG_AUXDISPLAY is not set
# CONFIG_BBRAM is not set
# CONFIG_CAN is not set
# CONFIG_CHARGER is not set
CONFIG_CLOCK_CONTROL_NRF_FORCE_ALT=y
CONFIG_CLOCK_CONTROL_NRF=y
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC is not set
CONFIG_CLOCK_CONTROL_NRF_K32SRC_XTAL=y
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_SYNTH is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_500PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_250PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_150PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_100PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_75PPM is not set
CONFIG_CLOCK_CONTROL_NRF_K32SRC_50PPM=y
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_30PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_20PPM is not set
CONFIG_CLOCK_CONTROL_NRF_ACCURACY=50
# CONFIG_CLOCK_CONTROL_FIXED_RATE_CLOCK is not set
CONFIG_CONSOLE_INPUT_MAX_LINE_LEN=128
CONFIG_CONSOLE_INIT_PRIORITY=40
# CONFIG_RAM_CONSOLE is not set
# CONFIG_IPM_CONSOLE_SENDER is not set
# CONFIG_IPM_CONSOLE_RECEIVER is not set
# CONFIG_UART_MCUMGR is not set
# CONFIG_GSM_MUX is not set
# CONFIG_EFI_CONSOLE is not set
# CONFIG_COREDUMP_DEVICE is not set
# CONFIG_CRYPTO is not set
# CONFIG_DAC is not set
# CONFIG_DAI is not set
# CONFIG_DISK_DRIVERS is not set
# CONFIG_DISPLAY is not set
# CONFIG_DMA is not set
# CONFIG_EDAC is not set
# CONFIG_EEPROM is not set
CONFIG_ENTROPY_GENERATOR=y
CONFIG_ENTROPY_NRF5_RNG=y
# CONFIG_ENTROPY_NRF5_BIAS_CORRECTION is not set
CONFIG_ENTROPY_NRF5_THR_POOL_SIZE=8
CONFIG_ENTROPY_NRF5_THR_THRESHOLD=4
CONFIG_ENTROPY_NRF5_ISR_POOL_SIZE=16
CONFIG_ENTROPY_NRF5_ISR_THRESHOLD=12
CONFIG_ENTROPY_HAS_DRIVER=y
# CONFIG_ESPI is not set
# CONFIG_FLASH is not set
# CONFIG_FPGA is not set
# CONFIG_FUEL_GAUGE is not set
# CONFIG_GNSS is not set
# CONFIG_GPIO_GET_DIRECTION is not set
# CONFIG_GPIO_GET_CONFIG is not set
# CONFIG_GPIO_HOGS is not set
# CONFIG_GPIO_ENABLE_DISABLE_INTERRUPT is not set
CONFIG_GPIO_NRFX=y
CONFIG_GPIO_NRFX_INTERRUPT=y
# CONFIG_HWINFO is not set
# CONFIG_HWSPINLOCK is not set
# CONFIG_I2C is not set
# CONFIG_I2S is not set
# CONFIG_I3C is not set

#
# Interrupt controller drivers
#
CONFIG_INTC_INIT_PRIORITY=40
# CONFIG_INTC_ESP32 is not set
# end of Interrupt controller drivers

# CONFIG_IPM is not set
# CONFIG_KSCAN is not set
# CONFIG_LED is not set
# CONFIG_LED_STRIP is not set
# CONFIG_LORA is not set
CONFIG_MBOX_INIT_PRIORITY=40
# CONFIG_MDIO is not set
# CONFIG_MIPI_DBI is not set

#
# Miscellaneous Drivers
#
# CONFIG_TIMEAWARE_GPIO is not set
# end of Miscellaneous Drivers

# CONFIG_MM_DRV is not set
# CONFIG_PCIE is not set
# CONFIG_PCIE_ENDPOINT is not set
# CONFIG_PECI is not set
# CONFIG_PM_CPU_OPS is not set
# CONFIG_PS2 is not set
# CONFIG_PTP_CLOCK is not set
# CONFIG_PWM is not set
# CONFIG_REGULATOR is not set
# CONFIG_RETAINED_MEM is not set
# CONFIG_RTC is not set
# CONFIG_SDHC is not set
# CONFIG_SMBUS is not set

#
# Timer drivers
#
# CONFIG_TIMER_READS_ITS_FREQUENCY_AT_RUNTIME is not set
# CONFIG_SYSTEM_CLOCK_SLOPPY_IDLE is not set
CONFIG_SYSTEM_CLOCK_INIT_PRIORITY=0
CONFIG_TICKLESS_CAPABLE=y
CONFIG_SYSTEM_TIMER_HAS_DISABLE_SUPPORT=y
CONFIG_NRF_RTC_TIMER_LOCK_ZERO_LATENCY_IRQS=y
# CONFIG_NRF_RTC_TIMER_TRIGGER_OVERFLOW is not set
# CONFIG_SYSTEM_CLOCK_NO_WAIT is not set
# CONFIG_SYSTEM_CLOCK_WAIT_FOR_AVAILABILITY is not set
CONFIG_SYSTEM_CLOCK_WAIT_FOR_STABILITY=y
# end of Timer drivers

# CONFIG_USB_BC12 is not set
# CONFIG_UDC_DRIVER is not set
# CONFIG_UHC_DRIVER is not set
# CONFIG_UVB is not set
# CONFIG_USB_DEVICE_DRIVER is not set
# CONFIG_USBC_TCPC_DRIVER is not set
# CONFIG_USBC_VBUS_DRIVER is not set
# CONFIG_USBC_PPC_DRIVER is not set
# CONFIG_VIDEO is not set
# CONFIG_VIRTUALIZATION is not set
# CONFIG_W1 is not set
# end of Device Drivers

# CONFIG_REQUIRES_FULL_LIBC is not set
# CONFIG_REQUIRES_FLOAT_PRINTF is not set
CONFIG_FULL_LIBC_SUPPORTED=y
CONFIG_MINIMAL_LIBC_SUPPORTED=y
CONFIG_NEWLIB_LIBC_SUPPORTED=y
CONFIG_PICOLIBC_SUPPORTED=y

#
# C Library
#
# CONFIG_MINIMAL_LIBC is not set
CONFIG_PICOLIBC=y
# CONFIG_NEWLIB_LIBC is not set
# CONFIG_EXTERNAL_LIBC is not set
CONFIG_HAS_NEWLIB_LIBC_NANO=y
CONFIG_COMMON_LIBC_ABORT=y
CONFIG_COMMON_LIBC_MALLOC=y
CONFIG_COMMON_LIBC_CALLOC=y
CONFIG_COMMON_LIBC_REALLOCARRAY=y
# CONFIG_PICOLIBC_USE_MODULE is not set
CONFIG_PICOLIBC_USE_TOOLCHAIN=y
CONFIG_PICOLIBC_HEAP_SIZE=-2
# CONFIG_PICOLIBC_IO_FLOAT is not set
CONFIG_PICOLIBC_IO_LONG_LONG=y
CONFIG_NEED_LIBC_MEM_PARTITION=y
# end of C Library

#
# C++ Language Support
#
# CONFIG_CPP is not set

#
# Deprecated
#
# CONFIG_CPLUSPLUS is not set
# CONFIG_LIB_CPLUSPLUS is not set
# end of Deprecated
# end of C++ Language Support

# CONFIG_CRC is not set

#
# Additional libraries
#

#
# Hash Function Support
#
# CONFIG_SYS_HASH_FUNC32 is not set
# end of Hash Function Support

#
# Hashmap (Hash Table) Support
#
# CONFIG_SYS_HASH_MAP is not set
# end of Hashmap (Hash Table) Support

#
# Heap and Memory Allocation
#
# CONFIG_SYS_HEAP_VALIDATE is not set
# CONFIG_SYS_HEAP_STRESS is not set
# CONFIG_SYS_HEAP_INFO is not set
CONFIG_SYS_HEAP_ALLOC_LOOPS=3
# CONFIG_SYS_HEAP_RUNTIME_STATS is not set
# CONFIG_SYS_HEAP_LISTENER is not set
# CONFIG_SYS_HEAP_SMALL_ONLY is not set
# CONFIG_SYS_HEAP_BIG_ONLY is not set
CONFIG_SYS_HEAP_AUTO=y
# CONFIG_MULTI_HEAP is not set
# CONFIG_SHARED_MULTI_HEAP is not set
# end of Heap and Memory Allocation

#
# Memory Blocks
#
# CONFIG_SYS_MEM_BLOCKS is not set
# end of Memory Blocks

#
# OS Support Library
#
# CONFIG_FDTABLE is not set
# CONFIG_PRINTK_SYNC is not set
# CONFIG_MPSC_PBUF is not set
# CONFIG_SPSC_PBUF is not set
CONFIG_CBPRINTF_COMPLETE=y
# CONFIG_CBPRINTF_NANO is not set
CONFIG_CBPRINTF_FULL_INTEGRAL=y
# CONFIG_CBPRINTF_REDUCED_INTEGRAL is not set
# CONFIG_CBPRINTF_FP_SUPPORT is not set
# CONFIG_CBPRINTF_FP_A_SUPPORT is not set
# CONFIG_CBPRINTF_LIBC_SUBSTS is not set
# CONFIG_CBPRINTF_PACKAGE_LONGDOUBLE is not set
# CONFIG_CBPRINTF_STATIC_PACKAGE_CHECK_ALIGNMENT is not set
CONFIG_CBPRINTF_CONVERT_CHECK_PTR=y
# end of OS Support Library

#
# POSIX API Support
#

#
# POSIX Options
#
# CONFIG_POSIX_API is not set
# CONFIG_POSIX_ASYNCHRONOUS_IO is not set
# CONFIG_POSIX_CLOCK is not set
# CONFIG_POSIX_CONFSTR is not set
# CONFIG_POSIX_ENV is not set
# CONFIG_EVENTFD is not set

#
# File descriptor table options
#
# end of File descriptor table options

# CONFIG_FNMATCH is not set
# CONFIG_GETENTROPY is not set
# CONFIG_POSIX_MQUEUE is not set

#
# sem_t support
#
CONFIG_SEM_VALUE_MAX=32767
CONFIG_SEM_NAMELEN_MAX=16
# end of sem_t support

#
# Signal support
#
CONFIG_POSIX_RTSIG_MAX=0
# CONFIG_POSIX_SIGNAL is not set
# end of Signal support

# CONFIG_POSIX_PUTMSG is not set

#
# Sysconf support
#
# CONFIG_POSIX_SYSCONF is not set
CONFIG_POSIX_PAGE_SIZE_BITS=6
# end of Sysconf support

# CONFIG_POSIX_SYSLOG is not set
# CONFIG_TIMER is not set
# CONFIG_POSIX_UNAME is not set
# end of POSIX Options

#
# POSIX Shell Utilities
#
# end of POSIX Shell Utilities
# end of POSIX API Support

# CONFIG_OPENAMP_RSC_TABLE is not set
# CONFIG_SMF is not set
CONFIG_LIBGCC_RTLIB=y

#
# Utility Library
#
# CONFIG_JSON_LIBRARY is not set
# CONFIG_RING_BUFFER is not set
CONFIG_NOTIFY=y
# CONFIG_BASE64 is not set
CONFIG_ONOFF=y
# CONFIG_WINSTREAM is not set
# CONFIG_UTF8 is not set
# end of Utility Library
# end of Additional libraries

#
# Subsystems and OS Services
#
# CONFIG_BINDESC is not set
CONFIG_BT=y
CONFIG_BT_HCI=y
# CONFIG_BT_CUSTOM is not set
CONFIG_BT_HCI_RAW=y
# CONFIG_BT_HCI_RAW_H4 is not set
# CONFIG_BT_HCI_RAW_CMD_EXT is not set
CONFIG_BT_CONN_TX=y
# CONFIG_BT_SCA_UPDATE is not set
# CONFIG_BT_TRANSMIT_POWER_CONTROL is not set
# CONFIG_BT_ISO_PERIPHERAL is not set
# CONFIG_BT_ISO_CENTRAL is not set
# CONFIG_BT_ISO_BROADCASTER is not set
# CONFIG_BT_ISO_SYNC_RECEIVER is not set

#
# Bluetooth buffer configuration
#
# end of Bluetooth buffer configuration

#
# Bluetooth Host
#

#
# Bluetooth Classic Options
#
# end of Bluetooth Classic Options
# end of Bluetooth Host

CONFIG_BT_CTLR_LE_ENC_SUPPORT=y
CONFIG_BT_CTLR_EXT_REJ_IND_SUPPORT=y
CONFIG_BT_CTLR_DATA_LEN_UPDATE_SUPPORT=y
CONFIG_BT_CTLR_PRIVACY_SUPPORT=y
CONFIG_BT_CTLR_EXT_SCAN_FP_SUPPORT=y
CONFIG_BT_CTLR_PHY_UPDATE_SUPPORT=y
CONFIG_BT_CTLR_PHY_2M_SUPPORT=y
CONFIG_BT_CTLR_PHY_CODED_SUPPORT=y
CONFIG_BT_CTLR_ADV_EXT_SUPPORT=y
CONFIG_BT_CTLR_ADV_PERIODIC_SUPPORT=y
CONFIG_BT_CTLR_ADV_PERIODIC_RSP_SUPPORT=y
CONFIG_BT_CTLR_SYNC_PERIODIC_SUPPORT=y
CONFIG_BT_CTLR_SYNC_PERIODIC_RSP_SUPPORT=y
CONFIG_BT_CTLR_SYNC_TRANSFER_SENDER_SUPPORT=y
CONFIG_BT_CTLR_SYNC_TRANSFER_RECEIVER_SUPPORT=y
CONFIG_BT_CTLR_ADV_ISO_SUPPORT=y
CONFIG_BT_CTLR_SYNC_ISO_SUPPORT=y
CONFIG_BT_CTLR_CENTRAL_ISO_SUPPORT=y
CONFIG_BT_CTLR_PERIPHERAL_ISO_SUPPORT=y
CONFIG_BT_CTLR_CHAN_SEL_2_SUPPORT=y
CONFIG_BT_CTLR_SCA_UPDATE_SUPPORT=y
CONFIG_BT_CTLR_CONN_RSSI_SUPPORT=y
CONFIG_BT_CTLR_ECDH_SUPPORT=y
CONFIG_BT_CTLR_LE_POWER_CONTROL_SUPPORT=y
# CONFIG_BT_LL_SW_SPLIT is not set
CONFIG_BT_CTLR_HCI=y

#
# BLE Controller configuration
#
CONFIG_BT_CTLR_CRYPTO=y
CONFIG_BT_CTLR_HCI_VS_BUILD_INFO=""
# CONFIG_BT_CTLR_TX_PWR_PLUS_3 is not set
# CONFIG_BT_CTLR_TX_PWR_PLUS_2 is not set
# CONFIG_BT_CTLR_TX_PWR_PLUS_1 is not set
CONFIG_BT_CTLR_TX_PWR_0=y
# CONFIG_BT_CTLR_TX_PWR_MINUS_1 is not set
# CONFIG_BT_CTLR_TX_PWR_MINUS_2 is not set
# CONFIG_BT_CTLR_TX_PWR_MINUS_3 is not set
# CONFIG_BT_CTLR_TX_PWR_MINUS_4 is not set
# CONFIG_BT_CTLR_TX_PWR_MINUS_5 is not set
# CONFIG_BT_CTLR_TX_PWR_MINUS_6 is not set
# CONFIG_BT_CTLR_TX_PWR_MINUS_7 is not set
# CONFIG_BT_CTLR_TX_PWR_MINUS_8 is not set
# CONFIG_BT_CTLR_TX_PWR_MINUS_12 is not set
# CONFIG_BT_CTLR_TX_PWR_MINUS_16 is not set
# CONFIG_BT_CTLR_TX_PWR_MINUS_20 is not set
# CONFIG_BT_CTLR_TX_PWR_MINUS_40 is not set
CONFIG_BT_CTLR_TX_PWR_DBM=0
CONFIG_BT_CTLR_TX_PWR_ANTENNA=0
# CONFIG_BT_CTLR_TX_PWR_DYNAMIC_CONTROL is not set

#
# BLE Controller features
#
CONFIG_BT_CTLR_LE_ENC=y
CONFIG_BT_CTLR_ECDH=y
CONFIG_BT_CTLR_EXT_REJ_IND=y
CONFIG_BT_CTLR_LE_PING=y
CONFIG_BT_CTLR_DATA_LENGTH=y
CONFIG_BT_CTLR_PHY=y
CONFIG_BT_CTLR_CONN_RSSI=y
# CONFIG_BT_CTLR_LE_POWER_CONTROL is not set
CONFIG_BT_CTLR_FILTER_ACCEPT_LIST=y
CONFIG_BT_CTLR_PRIVACY=y
CONFIG_BT_CTLR_RL_SIZE=8
CONFIG_BT_CTLR_EXT_SCAN_FP=y
CONFIG_BT_CTLR_PHY_2M=y
CONFIG_BT_CTLR_PHY_CODED=y
CONFIG_BT_CTLR_CHAN_SEL_2=y
# CONFIG_BT_CTLR_ADV_EXT is not set
# CONFIG_BT_CTLR_SET_HOST_FEATURE is not set
# CONFIG_BT_CTLR_CENTRAL_ISO is not set
# CONFIG_BT_CTLR_PERIPHERAL_ISO is not set
# CONFIG_BT_CTLR_HCI_CODEC_AND_DELAY_INFO is not set
CONFIG_BT_CTLR_DF_CTE_TX_SUPPORT=y
CONFIG_BT_CTLR_ASSERT_HANDLER=y
# CONFIG_BT_CTLR_VS_SCAN_REQ_RX is not set
# CONFIG_BT_SHELL is not set
# CONFIG_BT_EAD is not set

#
# Controller Area Network (CAN) bus subsystem
#
# end of Controller Area Network (CAN) bus subsystem

# CONFIG_CONSOLE_SUBSYS is not set

#
# System Monitoring Options
#
# CONFIG_THREAD_ANALYZER is not set
# end of System Monitoring Options

#
# Debugging Options
#
# CONFIG_DEBUG is not set
# CONFIG_STACK_USAGE is not set
# CONFIG_STACK_SENTINEL is not set
CONFIG_PRINTK=y
CONFIG_EARLY_CONSOLE=y
CONFIG_ASSERT=y
CONFIG_ASSERT_LEVEL=2
CONFIG_SPIN_VALIDATE=y
# CONFIG_FORCE_NO_ASSERT is not set
CONFIG_ASSERT_VERBOSE=y
# CONFIG_ASSERT_NO_FILE_INFO is not set
# CONFIG_ASSERT_NO_COND_INFO is not set
# CONFIG_ASSERT_NO_MSG_INFO is not set
# CONFIG_ASSERT_TEST is not set
# CONFIG_OVERRIDE_FRAME_POINTER_DEFAULT is not set
CONFIG_DEBUG_INFO=y
CONFIG_EXCEPTION_STACK_TRACE=y
# CONFIG_DEBUG_THREAD_INFO is not set
# CONFIG_DEBUG_COREDUMP is not set
# end of Debugging Options

# CONFIG_MIPI_STP_DECODER is not set
# CONFIG_DISK_ACCESS is not set
# CONFIG_DSP is not set
# CONFIG_EMUL is not set
# CONFIG_CHARACTER_FRAMEBUFFER is not set

#
# File Systems
#
# CONFIG_FILE_SYSTEM is not set
# end of File Systems

#
# Inter Processor Communication
#
# CONFIG_RPMSG_SERVICE is not set
CONFIG_IPC_SERVICE=y
CONFIG_IPC_SERVICE_REG_BACKEND_PRIORITY=46
CONFIG_IPC_SERVICE_BACKEND_RPMSG=y
CONFIG_IPC_SERVICE_BACKEND_RPMSG_WQ_STACK_SIZE=1024
CONFIG_IPC_SERVICE_BACKEND_RPMSG_NUM_ENDPOINTS_PER_INSTANCE=2
CONFIG_IPC_SERVICE_RPMSG=y
CONFIG_IPC_SERVICE_STATIC_VRINGS=y
CONFIG_IPC_SERVICE_STATIC_VRINGS_MEM_ALIGNMENT=4
# CONFIG_IPC_SERVICE_ICMSG is not set
# CONFIG_IPC_SERVICE_ICMSG_ME is not set
# end of Inter Processor Communication

# CONFIG_JWT is not set
# CONFIG_LLEXT is not set

#
# Linkable loadable Extension Development Kit (EDK)
#
CONFIG_LLEXT_EDK_NAME="llext-edk"
# CONFIG_LLEXT_EDK_USERSPACE_ONLY is not set
# end of Linkable loadable Extension Development Kit (EDK)

#
# Logging
#
# CONFIG_LOG_OUTPUT is not set
# end of Logging

CONFIG_MEM_ATTR=y
# CONFIG_MEM_ATTR_HEAP is not set

#
# Device Management
#

#
# Host command handler subsystem
#
# CONFIG_EC_HOST_CMD is not set
# end of Host command handler subsystem

# CONFIG_OSDP is not set
# end of Device Management

# CONFIG_MODBUS is not set
# CONFIG_MODEM_MODULES is not set

#
# Networking
#
CONFIG_NET_BUF=y
# CONFIG_NET_BUF_LOG is not set
# CONFIG_NET_BUF_POOL_USAGE is not set
CONFIG_NET_BUF_ALIGNMENT=0
# CONFIG_NETWORKING is not set
# end of Networking

#
# Power Management
#
# end of Power Management

#
# Portability
#
# end of Portability

#
# Random Number Generators
#
# CONFIG_TEST_RANDOM_GENERATOR is not set
CONFIG_TIMER_RANDOM_INITIAL_STATE=123456789
CONFIG_ENTROPY_DEVICE_RANDOM_GENERATOR=y
# CONFIG_XOSHIRO_RANDOM_GENERATOR is not set
CONFIG_CSPRNG_ENABLED=y
CONFIG_HARDWARE_DEVICE_CS_GENERATOR=y
# CONFIG_CTR_DRBG_CSPRNG_GENERATOR is not set
# end of Random Number Generators

# CONFIG_RTIO is not set

#
# SD
#
# CONFIG_MMC_STACK is not set
# CONFIG_SDMMC_STACK is not set
# CONFIG_SDIO_STACK is not set
# end of SD

# CONFIG_SETTINGS is not set
# CONFIG_SHELL is not set
# CONFIG_STATS is not set

#
# Storage
#
# CONFIG_STREAM_FLASH is not set
# end of Storage

# CONFIG_TASK_WDT is not set

#
# Testing
#
# CONFIG_ZTEST is not set
# CONFIG_ZTEST_MOCKING is not set
# CONFIG_ZTRESS is not set
# CONFIG_TEST is not set
CONFIG_COVERAGE_GCOV_HEAP_SIZE=16384
# CONFIG_FORCE_COVERAGE is not set
# CONFIG_TEST_USERSPACE is not set
# end of Testing

# CONFIG_TIMING_FUNCTIONS is not set
# CONFIG_TRACING is not set
# CONFIG_USB_DEVICE_STACK is not set
# CONFIG_USB_DEVICE_STACK_NEXT is not set
# CONFIG_USB_HOST_STACK is not set
# CONFIG_USBC_STACK is not set
# CONFIG_ZBUS is not set
# CONFIG_MODULES is not set
# end of Subsystems and OS Services

CONFIG_TOOLCHAIN_ZEPHYR_0_16=y
CONFIG_TOOLCHAIN_ZEPHYR_SUPPORTS_THREAD_LOCAL_STORAGE=y

#
# Build and Link Features
#

#
# Linker Options
#
# CONFIG_LINKER_ORPHAN_SECTION_PLACE is not set
CONFIG_LINKER_ORPHAN_SECTION_WARN=y
# CONFIG_LINKER_ORPHAN_SECTION_ERROR is not set
CONFIG_ROM_END_OFFSET=0
CONFIG_LD_LINKER_SCRIPT_SUPPORTED=y
CONFIG_LD_LINKER_TEMPLATE=y
# CONFIG_CMAKE_LINKER_GENERATOR is not set
# CONFIG_HAVE_CUSTOM_LINKER_SCRIPT is not set
CONFIG_LINKER_SORT_BY_ALIGNMENT=y

#
# Linker Sections
#
# CONFIG_LINKER_USE_BOOT_SECTION is not set
# CONFIG_LINKER_USE_PINNED_SECTION is not set
CONFIG_LINKER_GENERIC_SECTIONS_PRESENT_AT_BOOT=y
CONFIG_LINKER_LAST_SECTION_ID=y
CONFIG_LINKER_LAST_SECTION_ID_PATTERN=0xE015E015
CONFIG_LINKER_USE_RELAX=y
# end of Linker Sections

CONFIG_LINKER_ITERABLE_SUBALIGN=4
CONFIG_LINKER_DEVNULL_SUPPORT=y
# CONFIG_LINKER_DEVNULL_MEMORY is not set
# end of Linker Options

#
# Compiler Options
#
# CONFIG_STD_C90 is not set
CONFIG_STD_C99=y
# CONFIG_STD_C11 is not set
# CONFIG_STD_C17 is not set
# CONFIG_STD_C23 is not set
CONFIG_TOOLCHAIN_SUPPORTS_GNU_EXTENSIONS=y
# CONFIG_GNU_C_EXTENSIONS is not set
# CONFIG_CODING_GUIDELINE_CHECK is not set
# CONFIG_COMPILER_FREESTANDING is not set
CONFIG_SIZE_OPTIMIZATIONS=y
# CONFIG_SPEED_OPTIMIZATIONS is not set
# CONFIG_DEBUG_OPTIMIZATIONS is not set
# CONFIG_NO_OPTIMIZATIONS is not set
# CONFIG_COMPILER_WARNINGS_AS_ERRORS is not set
# CONFIG_COMPILER_SAVE_TEMPS is not set
CONFIG_COMPILER_TRACK_MACRO_EXPANSION=y
CONFIG_COMPILER_COLOR_DIAGNOSTICS=y
# CONFIG_FORTIFY_SOURCE_NONE is not set
CONFIG_FORTIFY_SOURCE_COMPILE_TIME=y
# CONFIG_FORTIFY_SOURCE_RUN_TIME is not set
CONFIG_COMPILER_OPT=""
# CONFIG_MISRA_SANE is not set
# end of Compiler Options

# CONFIG_ASSERT_ON_ERRORS is not set
# CONFIG_NO_RUNTIME_CHECKS is not set
CONFIG_RUNTIME_ERROR_CHECKS=y

#
# Build Options
#
CONFIG_KERNEL_BIN_NAME="zephyr"
CONFIG_OUTPUT_STAT=y
# CONFIG_OUTPUT_SYMBOLS is not set
# CONFIG_OUTPUT_DISASSEMBLY is not set
CONFIG_OUTPUT_PRINT_MEMORY_USAGE=y
# CONFIG_CLEANUP_INTERMEDIATE_FILES is not set
# CONFIG_BUILD_NO_GAP_FILL is not set
# CONFIG_BUILD_OUTPUT_EXE is not set
# CONFIG_BUILD_OUTPUT_S19 is not set
# CONFIG_BUILD_OUTPUT_UF2 is not set
# CONFIG_BUILD_OUTPUT_STRIPPED is not set
# CONFIG_BUILD_OUTPUT_COMPRESS_DEBUG_SECTIONS is not set
# CONFIG_BUILD_ALIGN_LMA is not set
# CONFIG_APPLICATION_DEFINED_SYSCALL is not set
# CONFIG_MAKEFILE_EXPORTS is not set
# CONFIG_BUILD_OUTPUT_META is not set
CONFIG_BUILD_OUTPUT_STRIP_PATHS=y
CONFIG_CHECK_INIT_PRIORITIES=y
# CONFIG_EMIT_ALL_SYSCALLS is not set
# end of Build Options

CONFIG_WARN_DEPRECATED=y
CONFIG_ENFORCE_ZEPHYR_STDINT=y
# end of Build and Link Features

#
# Boot Options
#
# CONFIG_IS_BOOTLOADER is not set
# CONFIG_BOOTLOADER_BOSSA is not set
# end of Boot Options

Here is my build command:

west build -b nrf5340dk/nrf5340/cpuapp --sysbuild -- -Dperipheral_uart_SHIELD=nrf21540ek_fwd -Dipc_radio_SHIELD=nrf21540ek

If you want GPIO+SPI, simply add -Dipc_radio_CONFIG_MPSL_FEM_NRF21540_GPIO_SPI=y to the build command.

If you are using the nRF Connect for VS Code extension, the -D* configs should go into extra CMake arguments while creating a build configuration.

Hieu

RE: how to enable GPIO+SPI mode on ble application

nk — Mon, 23 Sep 2024 22:13:39 GMT

how about the progress?

RE: how to enable GPIO+SPI mode on ble application

nk — Sun, 08 Sep 2024 22:59:43 GMT

yes, I could build, but cpunet fem configration is not available. how about your build result?

RE: how to enable GPIO+SPI mode on ble application

Susheel Nuguru — Tue, 03 Sep 2024 07:53:41 GMT

Hmm, I see the same error now that you see. But I did have this compiled properly.

Can you please try to build this in NCSv2.7.0. I took clean sdk and sourced the zephyr\zephyr-env.sh and compiled the project.

Things have improved in terms of ease of build in this revision. I used this command

west build -p -b nrf5340dk/nrf5340/cpuapp -- -Dcentral_and_peripheral_hr_SHIELD=nrf21540ek_fwd -Dipc_radio_SHIELD=nrf21540ek

and I get this output

$ west build -p -b nrf5340dk/nrf5340/cpuapp -- -Dcentral_and_peripheral_SHIELD=nrf21540ek_fwd -Dipc_radio_SHIELD=nrf21540ek
-- west build: generating a build system
Loading Zephyr module(s) (Zephyr base): sysbuild_default
-- Found Python3: C:/Python/python.exe (found suitable version "3.12.3", minimum required is "3.8") found components: Interpreter
-- Cache files will be written to: E:/ncs/2.7.0/zephyr/.cache
-- Found west (found suitable version "1.2.0", minimum required is "0.14.0")
-- Board: nrf5340dk, qualifiers: nrf5340/cpuapp
Parsing E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/Kconfig.sysbuild
Loaded configuration 'E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/build/_sysbuild/empty.conf'
Merged configuration 'E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/build/_sysbuild/empty.conf'
Configuration saved to 'E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/build/zephyr/.config'
Kconfig header saved to 'E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/build/_sysbuild/autoconf.h'
--
   ***********************************************
   * Running CMake for central_and_peripheral_hr *
   ***********************************************

Loading Zephyr default modules (Zephyr base).
-- Application: E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr
-- CMake version: 3.22.0
-- Using NCS Toolchain 2.6.20240605.885759407716 for building. (E:/ncs/toolchains/ce3b5ff664/cmake)
-- Found Python3: E:/ncs/toolchains/ce3b5ff664/opt/bin/python.exe (found suitable version "3.9.13", minimum required is "3.8") found components: Interpreter
-- Cache files will be written to: E:/ncs/2.7.0/zephyr/.cache
-- Zephyr version: 3.6.99 (E:/ncs/2.7.0/zephyr)
-- Found west (found suitable version "1.2.0", minimum required is "0.14.0")
-- Board: nrf5340dk, qualifiers: nrf5340/cpuapp
-- Found host-tools: zephyr 0.16.5 (E:/ncs/toolchains/ce3b5ff664/opt/zephyr-sdk)
-- Found toolchain: zephyr 0.16.5 (E:/ncs/toolchains/ce3b5ff664/opt/zephyr-sdk)
-- Found Dtc: E:/ncs/toolchains/ce3b5ff664/opt/bin/dtc.exe (found suitable version "1.4.7", minimum required is "1.4.6")
-- Found BOARD.dts: E:/ncs/2.7.0/zephyr/boards/nordic/nrf5340dk/nrf5340dk_nrf5340_cpuapp.dts
-- Generated zephyr.dts: E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/build/central_and_peripheral_hr/zephyr/zephyr.dts
-- Generated devicetree_generated.h: E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/build/central_and_peripheral_hr/zephyr/include/generated/devicetree_ge
nerated.h
-- Including generated dts.cmake file: E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/build/central_and_peripheral_hr/zephyr/dts.cmake
Parsing E:/ncs/2.7.0/zephyr/Kconfig
Loaded configuration 'E:/ncs/2.7.0/zephyr/boards/nordic/nrf5340dk/nrf5340dk_nrf5340_cpuapp_defconfig'
Merged configuration 'E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/prj.conf'
Merged configuration 'E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/build/central_and_peripheral_hr/zephyr/.config.sysbuild'
Configuration saved to 'E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/build/central_and_peripheral_hr/zephyr/.config'
Kconfig header saved to 'E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/build/central_and_peripheral_hr/zephyr/include/generated/autoconf.h'
-- Found GnuLd: e:/ncs/toolchains/ce3b5ff664/opt/zephyr-sdk/arm-zephyr-eabi/arm-zephyr-eabi/bin/ld.bfd.exe (found version "2.38")
-- The C compiler identification is GNU 12.2.0
-- The CXX compiler identification is GNU 12.2.0
-- The ASM compiler identification is GNU
-- Found assembler: E:/ncs/toolchains/ce3b5ff664/opt/zephyr-sdk/arm-zephyr-eabi/bin/arm-zephyr-eabi-gcc.exe
-- libmetal version: 1.5.0 (E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr)
-- Build type:
-- Host:    Windows/AMD64
-- Target:  Generic/arm
-- Machine: arm
-- Looking for include file stdatomic.h
-- Looking for include file stdatomic.h - found
-- open-amp version: 1.5.0 (E:/ncs/2.7.0/modules/lib/open-amp/open-amp)
-- Host:    Windows/AMD64
-- Target:  Generic/arm
-- Machine: arm
-- C_FLAGS :  -Wall -Wextra
-- Looking for include file fcntl.h
-- Looking for include file fcntl.h - found
CMake Warning at E:/ncs/2.7.0/zephyr/kernel/CMakeLists.txt:170 (message):


          CONFIG_HEAP_MEM_POOL_SIZE is less than requested minimum:
            1024 < 4096
          Setting the system heap size to 4096


CMake Warning at E:/ncs/2.7.0/zephyr/CMakeLists.txt:2027 (message):
  __ASSERT() statements are globally ENABLED


-- Configuring done
-- Generating done
-- Build files have been written to: E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/build/central_and_peripheral_hr
--
   *******************************
   * Running CMake for ipc_radio *
   *******************************

Loading Zephyr default modules (Zephyr base).
-- Application: E:/ncs/2.7.0/nrf/applications/ipc_radio
-- CMake version: 3.22.0
-- Using NCS Toolchain 2.6.20240605.885759407716 for building. (E:/ncs/toolchains/ce3b5ff664/cmake)
-- Found Python3: E:/ncs/toolchains/ce3b5ff664/opt/bin/python.exe (found suitable version "3.9.13", minimum required is "3.8") found components: Interpreter
-- Cache files will be written to: E:/ncs/2.7.0/zephyr/.cache
-- Zephyr version: 3.6.99 (E:/ncs/2.7.0/zephyr)
-- Found west (found suitable version "1.2.0", minimum required is "0.14.0")
-- Board: nrf5340dk, qualifiers: nrf5340/cpunet
-- Shield(s): nrf21540ek
-- Found host-tools: zephyr 0.16.5 (E:/ncs/toolchains/ce3b5ff664/opt/zephyr-sdk)
-- Found toolchain: zephyr 0.16.5 (E:/ncs/toolchains/ce3b5ff664/opt/zephyr-sdk)
-- Found Dtc: E:/ncs/toolchains/ce3b5ff664/opt/bin/dtc.exe (found suitable version "1.4.7", minimum required is "1.4.6")
-- Found BOARD.dts: E:/ncs/2.7.0/zephyr/boards/nordic/nrf5340dk/nrf5340dk_nrf5340_cpunet.dts
-- Found devicetree overlay: E:/ncs/2.7.0/nrf/boards/shields/nrf21540ek/nrf21540ek.overlay
-- Generated zephyr.dts: E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/build/ipc_radio/zephyr/zephyr.dts
-- Generated devicetree_generated.h: E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/build/ipc_radio/zephyr/include/generated/devicetree_generated.h
-- Including generated dts.cmake file: E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/build/ipc_radio/zephyr/dts.cmake
Parsing E:/ncs/2.7.0/nrf/applications/ipc_radio/Kconfig
Loaded configuration 'E:/ncs/2.7.0/zephyr/boards/nordic/nrf5340dk/nrf5340dk_nrf5340_cpunet_defconfig'
Merged configuration 'E:/ncs/2.7.0/nrf/applications/ipc_radio/prj.conf'
Merged configuration 'E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/sysbuild/ipc_radio.conf'
Merged configuration 'E:/ncs/2.7.0/nrf/applications/ipc_radio/overlay-bt_hci_ipc.conf'
Merged configuration 'E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/build/ipc_radio/zephyr/.config.sysbuild'
Configuration saved to 'E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/build/ipc_radio/zephyr/.config'
Kconfig header saved to 'E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/build/ipc_radio/zephyr/include/generated/autoconf.h'
-- Found GnuLd: e:/ncs/toolchains/ce3b5ff664/opt/zephyr-sdk/arm-zephyr-eabi/arm-zephyr-eabi/bin/ld.bfd.exe (found version "2.38")
-- The C compiler identification is GNU 12.2.0
-- The CXX compiler identification is GNU 12.2.0
-- The ASM compiler identification is GNU
-- Found assembler: E:/ncs/toolchains/ce3b5ff664/opt/zephyr-sdk/arm-zephyr-eabi/bin/arm-zephyr-eabi-gcc.exe
-- libmetal version: 1.5.0 (E:/ncs/2.7.0/nrf/applications/ipc_radio)
-- Build type:
-- Host:    Windows/AMD64
-- Target:  Generic/arm
-- Machine: arm
-- Looking for include file stdatomic.h
-- Looking for include file stdatomic.h - found
-- open-amp version: 1.5.0 (E:/ncs/2.7.0/modules/lib/open-amp/open-amp)
-- Host:    Windows/AMD64
-- Target:  Generic/arm
-- Machine: arm
-- C_FLAGS :  -Wall -Wextra
-- Looking for include file fcntl.h
-- Looking for include file fcntl.h - found
CMake Warning at E:/ncs/2.7.0/zephyr/CMakeLists.txt:895 (message):
  No SOURCES given to Zephyr library: drivers__console

  Excluding target from build.


CMake Warning at E:/ncs/2.7.0/zephyr/CMakeLists.txt:2027 (message):
  __ASSERT() statements are globally ENABLED


-- Configuring done
-- Generating done
-- Build files have been written to: E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/build/ipc_radio
-- Configuring done
-- Generating done
-- Build files have been written to: E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/build
←[92m-- west build: building application
[9/20] Performing build step for 'central_and_peripheral_hr'
[4/255] Generating include/generated/version.h
-- Zephyr version: 3.6.99 (E:/ncs/2.7.0/zephyr), build: 100befc70c74
[255/255] Linking C executable zephyr\zephyr.elf
Memory region         Used Size  Region Size  %age Used
           FLASH:      152700 B      1008 KB     14.79%
             RAM:       33828 B       448 KB      7.37%
        IDT_LIST:          0 GB        32 KB      0.00%
Generating files from E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/build/central_and_peripheral_hr/zephyr/zephyr.elf for board: nrf5340dk
[11/20] Performing build step for 'ipc_radio'
[5/202] Generating include/generated/version.h
-- Zephyr version: 3.6.99 (E:/ncs/2.7.0/zephyr), build: 100befc70c74
[202/202] Linking C executable zephyr\zephyr.elf
Memory region         Used Size  Region Size  %age Used
           FLASH:      183860 B       256 KB     70.14%
             RAM:       55448 B        64 KB     84.61%
           SRAM1:          0 GB        64 KB      0.00%
        IDT_LIST:          0 GB        32 KB      0.00%
Generating files from E:/ncs/2.7.0/nrf/samples/bluetooth/central_and_peripheral_hr/build/ipc_radio/zephyr/zephyr.elf for board: nrf5340dk
[20/20] Generating ../merged_CPUNET.hex

With sysbuild which is now default the -DSHIELD=nrf21540ek_fwd alone causes the SHIELD variable to be defined to the value nrf21540ek_fwd within all images in the build for all cores. So when you build with

west build -p -b nrf5340dk/nrf5340/cpuapp -- -DSHIELD=nrf21540ek_fwd

the SHIELD=nrf21540ek_fwd is defined in peripheral_uart application that is build for nrf5340dk/nrf5340/cpuapp

and within ipc_radio image which is built automatically for nrf5340dk/nrf5340/cpunet.

The proper approach is to provide nrf21540k_fwd only to the image for cpuapp and the nrf21540ek to the cpunet image.

For each application you must know the image names produced for cpuapp and cpunet and provide appropriate namespace prefixing when running west build. In general it should be

west build -p -b nrf5340dk/nrf5340/cpuapp -- -D<image_name_for_cpuapp>_SHIELD=nrf21540ek_fwd -D<image_name_for_cpunet>_SHIELD=nrf21540ek

RE: how to enable GPIO+SPI mode on ble application

nk — Thu, 29 Aug 2024 01:00:59 GMT

it is strange. I re-checked by fresh wsl2 ubuntu22 env. I could not build. what wrong ?
I did not change the following install step.
Installing the nRF Connect SDK (nordicsemi.com)

~/tmp/ncs$ west build -p -b nrf5340dk/nrf5340/cpuapp -d build-peri-uart nrf/samples/bluetooth/peripheral_uart -- -DSHIELD=nrf21540ek_fwd -Dhci_ipc_SHIELD=nrf21540ek
-- west build: generating a build system
Loading Zephyr module(s) (Zephyr base): sysbuild_default
-- Found Python3: /home/user/ncs/toolchains/e9dba88316/usr/local/bin/python3.9 (found suitable version "3.9.18", minimum required is "3.8") found components: Interpreter 
-- Cache files will be written to: /home/user/.cache/zephyr
-- Found west (found suitable version "1.2.0", minimum required is "0.14.0")
-- Board: nrf5340dk, qualifiers: nrf5340/cpuapp
-- Shield(s): nrf21540ek_fwd
Parsing /home/user/tmp/ncs/nrf/samples/bluetooth/peripheral_uart/Kconfig.sysbuild
Loaded configuration '/home/user/tmp/ncs/build-peri-uart/_sysbuild/empty.conf'
Merged configuration '/home/user/tmp/ncs/nrf/samples/bluetooth/peripheral_uart/sysbuild.conf'
Configuration saved to '/home/user/tmp/ncs/build-peri-uart/zephyr/.config'
Kconfig header saved to '/home/user/tmp/ncs/build-peri-uart/_sysbuild/autoconf.h'
-- 
   *************************************
   * Running CMake for peripheral_uart *
   *************************************

Loading Zephyr default modules (Zephyr base).
-- Application: /home/user/tmp/ncs/nrf/samples/bluetooth/peripheral_uart
-- CMake version: 3.21.0
-- Using NCS Toolchain 2.6.20240605.1004412633878 for building. (/home/user/ncs/toolchains/e9dba88316/cmake)
-- Found Python3: /home/user/ncs/toolchains/e9dba88316/usr/local/bin/python3 (found suitable version "3.9.18", minimum required is "3.8") found components: Interpreter 
-- Cache files will be written to: /home/user/.cache/zephyr
-- Zephyr version: 3.6.99 (/home/user/tmp/ncs/zephyr)
-- Found west (found suitable version "1.2.0", minimum required is "0.14.0")
-- Board: nrf5340dk, qualifiers: nrf5340/cpuapp
-- Shield(s): nrf21540ek_fwd
-- Found host-tools: zephyr 0.16.5 (/home/user/ncs/toolchains/e9dba88316/opt/zephyr-sdk)
-- Found toolchain: zephyr 0.16.5 (/home/user/ncs/toolchains/e9dba88316/opt/zephyr-sdk)
-- Found Dtc: /home/user/ncs/toolchains/e9dba88316/usr/local/bin/dtc (found suitable version "1.5.0", minimum required is "1.4.6") 
-- Found BOARD.dts: /home/user/tmp/ncs/zephyr/boards/nordic/nrf5340dk/nrf5340dk_nrf5340_cpuapp.dts
-- Found devicetree overlay: /home/user/tmp/ncs/nrf/boards/shields/nrf21540ek/nrf21540ek_fwd.overlay
-- Found devicetree overlay: /home/user/tmp/ncs/nrf/samples/bluetooth/peripheral_uart/app.overlay
-- Generated zephyr.dts: /home/user/tmp/ncs/build-peri-uart/peripheral_uart/zephyr/zephyr.dts
-- Generated devicetree_generated.h: /home/user/tmp/ncs/build-peri-uart/peripheral_uart/zephyr/include/generated/devicetree_generated.h
-- Including generated dts.cmake file: /home/user/tmp/ncs/build-peri-uart/peripheral_uart/zephyr/dts.cmake
Parsing /home/user/tmp/ncs/nrf/samples/bluetooth/peripheral_uart/Kconfig
Loaded configuration '/home/user/tmp/ncs/zephyr/boards/nordic/nrf5340dk/nrf5340dk_nrf5340_cpuapp_defconfig'
Merged configuration '/home/user/tmp/ncs/nrf/samples/bluetooth/peripheral_uart/prj.conf'
Merged configuration '/home/user/tmp/ncs/build-peri-uart/peripheral_uart/zephyr/.config.sysbuild'
Configuration saved to '/home/user/tmp/ncs/build-peri-uart/peripheral_uart/zephyr/.config'
Kconfig header saved to '/home/user/tmp/ncs/build-peri-uart/peripheral_uart/zephyr/include/generated/autoconf.h'
-- Found GnuLd: /home/user/ncs/toolchains/e9dba88316/opt/zephyr-sdk/arm-zephyr-eabi/arm-zephyr-eabi/bin/ld.bfd (found version "2.38") 
-- The C compiler identification is GNU 12.2.0
-- The CXX compiler identification is GNU 12.2.0
-- The ASM compiler identification is GNU
-- Found assembler: /home/user/ncs/toolchains/e9dba88316/opt/zephyr-sdk/arm-zephyr-eabi/bin/arm-zephyr-eabi-gcc
-- libmetal version: 1.5.0 (/home/user/tmp/ncs/nrf/samples/bluetooth/peripheral_uart)
-- Build type:  
-- Host:    Linux/x86_64
-- Target:  Generic/arm
-- Machine: arm
-- Looking for include file stdatomic.h
-- Looking for include file stdatomic.h - found
-- open-amp version: 1.5.0 (/home/user/tmp/ncs/modules/lib/open-amp/open-amp)
-- Host:    Linux/x86_64
-- Target:  Generic/arm
-- Machine: arm
-- C_FLAGS :  -Wall -Wextra
-- Looking for include file fcntl.h
-- Looking for include file fcntl.h - found
-- Using ccache: /home/user/ncs/toolchains/e9dba88316/usr/bin/ccache
CMake Warning at /home/user/tmp/ncs/zephyr/kernel/CMakeLists.txt:170 (message):
  

          CONFIG_HEAP_MEM_POOL_SIZE is less than requested minimum:
            2048 < 4096
          Setting the system heap size to 4096


CMake Warning at /home/user/tmp/ncs/zephyr/CMakeLists.txt:2027 (message):
  __ASSERT() statements are globally ENABLED


-- Configuring done
-- Generating done
-- Build files have been written to: /home/user/tmp/ncs/build-peri-uart/peripheral_uart
-- 
   *******************************
   * Running CMake for ipc_radio *
   *******************************

Loading Zephyr default modules (Zephyr base).
-- Application: /home/user/tmp/ncs/nrf/applications/ipc_radio
-- CMake version: 3.21.0
-- Using NCS Toolchain 2.6.20240605.1004412633878 for building. (/home/user/ncs/toolchains/e9dba88316/cmake)
-- Found Python3: /home/user/ncs/toolchains/e9dba88316/usr/local/bin/python3 (found suitable version "3.9.18", minimum required is "3.8") found components: Interpreter 
-- Cache files will be written to: /home/user/.cache/zephyr
-- Zephyr version: 3.6.99 (/home/user/tmp/ncs/zephyr)
-- Found west (found suitable version "1.2.0", minimum required is "0.14.0")
-- Board: nrf5340dk, qualifiers: nrf5340/cpunet
-- Shield(s): nrf21540ek_fwd
-- Found host-tools: zephyr 0.16.5 (/home/user/ncs/toolchains/e9dba88316/opt/zephyr-sdk)
-- Found toolchain: zephyr 0.16.5 (/home/user/ncs/toolchains/e9dba88316/opt/zephyr-sdk)
-- Found Dtc: /home/user/ncs/toolchains/e9dba88316/usr/local/bin/dtc (found suitable version "1.5.0", minimum required is "1.4.6") 
-- Found BOARD.dts: /home/user/tmp/ncs/zephyr/boards/nordic/nrf5340dk/nrf5340dk_nrf5340_cpunet.dts
-- Found devicetree overlay: /home/user/tmp/ncs/nrf/boards/shields/nrf21540ek/nrf21540ek_fwd.overlay
devicetree error: /home/user/tmp/ncs/nrf/boards/shields/nrf21540ek/nrf21540ek_fwd.overlay:16 (column 1): parse error: undefined node label 'gpio_fwd'
-- In: /home/user/tmp/ncs/build-peri-uart/ipc_radio/zephyr, command: /home/user/ncs/toolchains/e9dba88316/usr/local/bin/python3;/home/user/tmp/ncs/zephyr/scripts/dts/gen_defines.py;--dts;/home/user/tmp/ncs/build-peri-uart/ipc_radio/zephyr/zephyr.dts.pre;--dtc-flags;'-Wno-unique_unit_address_if_enabled';--bindings-dirs;/home/user/tmp/ncs/nrf/dts/bindings;/home/user/tmp/ncs/zephyr/dts/bindings;--header-out;/home/user/tmp/ncs/build-peri-uart/ipc_radio/zephyr/include/generated/devicetree_generated.h.new;--dts-out;/home/user/tmp/ncs/build-peri-uart/ipc_radio/zephyr/zephyr.dts.new;--edt-pickle-out;/home/user/tmp/ncs/build-peri-uart/ipc_radio/zephyr/edt.pickle;--vendor-prefixes;/home/user/tmp/ncs/nrf/dts/bindings/vendor-prefixes.txt;--vendor-prefixes;/home/user/tmp/ncs/zephyr/dts/bindings/vendor-prefixes.txt
CMake Error at /home/user/tmp/ncs/zephyr/cmake/modules/dts.cmake:296 (message):
  gen_defines.py failed with return code: 1
Call Stack (most recent call first):
  /home/user/tmp/ncs/zephyr/cmake/modules/zephyr_default.cmake:132 (include)
  /home/user/tmp/ncs/zephyr/share/zephyr-package/cmake/ZephyrConfig.cmake:66 (include)
  /home/user/tmp/ncs/zephyr/share/zephyr-package/cmake/ZephyrConfig.cmake:92 (include_boilerplate)
  CMakeLists.txt:9 (find_package)


-- Configuring incomplete, errors occurred!
CMake Error at cmake/modules/sysbuild_extensions.cmake:486 (message):
  CMake configure failed for Zephyr project: ipc_radio

  Location: /home/user/tmp/ncs/nrf/applications/ipc_radio
Call Stack (most recent call first):
  cmake/modules/sysbuild_images.cmake:20 (ExternalZephyrProject_Cmake)
  cmake/modules/sysbuild_default.cmake:19 (include)
  /home/user/tmp/ncs/zephyr/share/zephyr-package/cmake/ZephyrConfig.cmake:75 (include)
  /home/user/tmp/ncs/zephyr/share/zephyr-package/cmake/ZephyrConfig.cmake:92 (include_boilerplate)
  /home/user/tmp/ncs/zephyr/share/sysbuild-package/cmake/SysbuildConfig.cmake:8 (include)
  template/CMakeLists.txt:10 (find_package)


-- Configuring incomplete, errors occurred!

RE: how to enable GPIO+SPI mode on ble application

Susheel Nuguru — Wed, 28 Aug 2024 10:32:14 GMT

I tried it long ago, but I had no problem running this sample with the command I shown in my previous reply.

RE: how to enable GPIO+SPI mode on ble application

nk — Fri, 23 Aug 2024 02:15:45 GMT

I updated ncs version to v2.7.0. I tried your the build way.
but the build was not success.

devicetree error: /home/user/ncs/nrf/boards/shields/nrf21540ek/nrf21540ek_fwd.overlay:16 (column 1): parse error: undefined node label 'gpio_fwd'

I used nrf/samples/bluetooth/peripheral_uart sample.
your env is no problem?

RE: how to enable GPIO+SPI mode on ble application

Susheel Nuguru — Tue, 18 Jun 2024 11:42:14 GMT

Hi Sorry, I had to delete my previous reply as it was wrong.

You need to still use this below

west build -b nrf5340dk_nrf5340_cpuapp -- -DSHIELD=nrf21540ek_fwd -Dhci_ipc_SHIELD=nrf21540ek

RE: how to enable GPIO+SPI mode on ble application

nk — Mon, 17 Jun 2024 07:41:18 GMT

please let me know your using ncs version. I am using ncs v2.4.1.
please comfirm whether 10dbm and 20dgm are controled by

BT_HCI_OP_VS_WRITE_TX_POWER_LEVEL command.

RE: how to enable GPIO+SPI mode on ble application

Susheel Nuguru — Mon, 17 Jun 2024 06:51:38 GMT

[deleted]

RE: how to enable GPIO+SPI mode on ble application

nk — Thu, 06 Jun 2024 23:07:33 GMT

I found to avoid the crash by increasing CONFIG_MAIN_STACK_SIZE but it seems we could NOT control MODE by SPI. please investigate.

RE: how to enable GPIO+SPI mode on ble application

Naeem Maroof — Thu, 06 Jun 2024 15:32:15 GMT

Hi,

Yes that is the correct way to set configs for the cpunet.

I can see that CONFIG_MPSL_FEM_NRF21540_GPIO_SPI gets set correctly for using the FEM module, but the application crashes in the HCI driver. I will discuss with Bluetooth experts.

RE: how to enable GPIO+SPI mode on ble application

nk — Wed, 29 May 2024 23:44:05 GMT

Hmm, please check my above message.

already I know I could enable CONFIG_MPSL_FEM_NRF21540_GPIO_SPI by creating child/hci_rpmsg.conf.

but it do not work. this way, is it correct ?

RE: how to enable GPIO+SPI mode on ble application

Naeem Maroof — Wed, 29 May 2024 13:51:09 GMT

Hi, the cofigs

CONFIG_MPSL_FEM_NRF21540_GPIO_SPI and CONFIG_MPSL_FEM_NRF21540_GPIO_SPI_SUPPORT are both enabled in the .config you have sent

RE: how to enable GPIO+SPI mode on ble application

nk — Mon, 27 May 2024 00:08:44 GMT

MPSL and FEM, no need. it is ok only CONFIG_MPSL_FEM_NRF21540_GPIO_SPI. the following is net cpu .config.

# CONFIG_NETWORKING is not set
# CONFIG_MODEM_ALT1250 is not set
# CONFIG_WIFI is not set
# CONFIG_MBEDTLS is not set
# CONFIG_NORDIC_SECURITY_BACKEND is not set
# CONFIG_INIT_STACKS is not set
CONFIG_ENTROPY_GENERATOR=y
# CONFIG_TEST_RANDOM_GENERATOR is not set
# CONFIG_ELTRES_CXM150X is not set
# CONFIG_SPI is not set
CONFIG_GPIO=y
# CONFIG_KSCAN is not set
# CONFIG_INPUT is not set
CONFIG_GPIO_INIT_PRIORITY=40
# CONFIG_UHC_DRIVER is not set
# CONFIG_REGULATOR is not set
# CONFIG_SENSOR is not set
# CONFIG_WATCHDOG is not set
# CONFIG_MODEM is not set
# CONFIG_UART_INTERRUPT_DRIVEN is not set
# CONFIG_DISPLAY is not set
# CONFIG_I2C is not set
CONFIG_BT_HCI_ACL_FLOW_CONTROL=y
CONFIG_BT_HCI_VS_EXT=y
CONFIG_BOARD="nrf5340dk_nrf5340_cpunet"
CONFIG_FLASH_LOAD_SIZE=0
CONFIG_SRAM_SIZE=64
CONFIG_FLASH_LOAD_OFFSET=0
CONFIG_MBOX_NRFX_IPC=y
CONFIG_HEAP_MEM_POOL_SIZE=8192
CONFIG_BT_CTLR=y
CONFIG_SOC="nRF5340_CPUNET_QKAA"
CONFIG_SOC_SERIES="nrf53"
CONFIG_NUM_IRQS=30
CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC=32768
CONFIG_CLOCK_CONTROL_INIT_PRIORITY=30
CONFIG_FLASH_SIZE=256
CONFIG_FLASH_BASE_ADDRESS=0x1000000
CONFIG_ICACHE_LINE_SIZE=32
CONFIG_DCACHE_LINE_SIZE=32
CONFIG_CLOCK_CONTROL=y
CONFIG_PINCTRL=y
CONFIG_ROM_START_OFFSET=0
# CONFIG_RESET is not set
CONFIG_SOC_HAS_TIMING_FUNCTIONS=y
CONFIG_ARCH_HAS_CUSTOM_BUSY_WAIT=y
# CONFIG_PM_DEVICE is not set
# CONFIG_IPC_SERVICE_BACKEND_RPMSG_SHMEM_RESET is not set
CONFIG_LOG_DOMAIN_NAME="net"
CONFIG_NRF_RTC_TIMER=y
CONFIG_SYS_CLOCK_TICKS_PER_SEC=32768
CONFIG_BUILD_OUTPUT_HEX=y
CONFIG_SERIAL_INIT_PRIORITY=55
# CONFIG_CODE_DATA_RELOCATION is not set
# CONFIG_MEMC is not set
# CONFIG_CPU_HAS_CUSTOM_FIXED_SOC_MPU_REGIONS is not set
CONFIG_TINYCRYPT=y
CONFIG_SERIAL=y
CONFIG_MAIN_STACK_SIZE=512
# CONFIG_SRAM_VECTOR_TABLE is not set
CONFIG_MP_MAX_NUM_CPUS=1
CONFIG_PLATFORM_SPECIFIC_INIT=y
CONFIG_HAS_DTS=y

#
# Devicetree Info
#
CONFIG_DT_HAS_ARDUINO_HEADER_R3_ENABLED=y
CONFIG_DT_HAS_ARM_ARMV8M_MPU_ENABLED=y
CONFIG_DT_HAS_ARM_CORTEX_M33_ENABLED=y
CONFIG_DT_HAS_ARM_V8M_NVIC_ENABLED=y
CONFIG_DT_HAS_FIXED_PARTITIONS_ENABLED=y
CONFIG_DT_HAS_GPIO_KEYS_ENABLED=y
CONFIG_DT_HAS_GPIO_LEDS_ENABLED=y
CONFIG_DT_HAS_MMIO_SRAM_ENABLED=y
CONFIG_DT_HAS_NORDIC_MBOX_NRF_IPC_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_ACL_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_CCM_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_CLOCK_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_DPPIC_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_ECB_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_EGU_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_FICR_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_GPIO_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_GPIOTE_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_GPREGRET_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_IEEE802154_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_IPC_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_PINCTRL_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_POWER_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_RADIO_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_RNG_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_SPIM_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_SWI_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_TEMP_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_UARTE_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_UICR_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_VMC_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_WDT_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF21540_FEM_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF21540_FEM_SPI_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF53_FLASH_CONTROLLER_ENABLED=y
CONFIG_DT_HAS_SOC_NV_FLASH_ENABLED=y
CONFIG_DT_HAS_ZEPHYR_BT_HCI_ENTROPY_ENABLED=y
CONFIG_DT_HAS_ZEPHYR_IPC_OPENAMP_STATIC_VRINGS_ENABLED=y
CONFIG_DT_HAS_ZEPHYR_MEMORY_REGION_ENABLED=y
# end of Devicetree Info

#
# Modules
#

#
# Available modules.
#

#
# nrf (/home/user/ncs_v2.4.1/nrf)
#
CONFIG_SHIELD_NRF21540_EK=y
CONFIG_NUM_METAIRQ_PRIORITIES=0
CONFIG_SYSTEM_WORKQUEUE_STACK_SIZE=512

#
# Nordic nRF Connect
#
CONFIG_WARN_EXPERIMENTAL=y
CONFIG_PRIVILEGED_STACK_SIZE=1024
CONFIG_BT_BUF_CMD_TX_COUNT=10
CONFIG_INIT_ARCH_HW_AT_BOOT=y
CONFIG_NORDIC_QSPI_NOR_FLASH_LAYOUT_PAGE_SIZE=2048
# CONFIG_GETOPT is not set
# CONFIG_NCS_SAMPLES_DEFAULTS is not set
# CONFIG_NCS_SAMPLE_EMPTY_APP_CORE_CHILD_IMAGE is not set

#
# Image build variants
#
# CONFIG_NCS_MCUBOOT_IN_BUILD is not set
# end of Image build variants

# CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU_SPEEDUP is not set
CONFIG_BT_BUF_ACL_TX_SIZE=27
CONFIG_BT_BUF_ACL_RX_SIZE=27
CONFIG_BT_CTLR_DATA_LENGTH_MAX=27

#
# Bootloader
#
# CONFIG_BUILD_S1_VARIANT is not set
# CONFIG_SECURE_BOOT is not set
CONFIG_PM_PARTITION_SIZE_PROVISION=0x280
# CONFIG_B0_MIN_PARTITION_SIZE is not set
CONFIG_PM_PARTITION_SIZE_B0_IMAGE=0x7800
# CONFIG_SECURE_BOOT_CRYPTO is not set

#
# Secure Boot firmware validation
#
CONFIG_SB_VALIDATION_INFO_MAGIC=0x86518483
CONFIG_SB_VALIDATION_POINTER_MAGIC=0x6919b47e
CONFIG_SB_VALIDATION_INFO_CRYPTO_ID=1
CONFIG_SB_VALIDATION_INFO_VERSION=2
CONFIG_SB_VALIDATION_METADATA_OFFSET=0
CONFIG_SB_VALIDATE_FW_HASH=y
# end of Secure Boot firmware validation
# end of Bootloader

#
# Bluetooth Low Energy
#
CONFIG_BT_MAX_CONN=16
CONFIG_BT_LL_SOFTDEVICE=y

#
# SoftDevice Controller
#
CONFIG_BT_LL_SOFTDEVICE_BUILD_TYPE_LIB=y
CONFIG_BT_HCI_TX_STACK_SIZE=1536
CONFIG_BT_RX_STACK_SIZE=768
CONFIG_BT_CTLR_SDC_PERIPHERAL_COUNT=1
CONFIG_BT_CTLR_SDC_MAX_CONN_EVENT_LEN_DEFAULT=7500
CONFIG_BT_CTLR_SDC_TX_PACKET_COUNT=3
CONFIG_BT_CTLR_SDC_RX_PACKET_COUNT=2
CONFIG_BT_CTLR_SDC_SCAN_BUFFER_COUNT=3
CONFIG_BT_CTLR_SDC_PERIODIC_SYNC_BUFFER_COUNT=2
CONFIG_BT_CTLR_SDC_RX_PRIO=6
# CONFIG_BT_CTLR_DF is not set
CONFIG_BT_LL_SOFTDEVICE_MULTIROLE=y
CONFIG_BT_SDC_ADDITIONAL_MEMORY=0
CONFIG_BT_CTLR_FAL_SIZE=8
CONFIG_BT_CTLR_ECDH_LIB_OBERON=y
# CONFIG_BT_CTLR_ECDH_LIB_TINYCRYPT is not set
CONFIG_BT_CTLR_ECDH_STACK_SIZE=900
# CONFIG_BT_CTLR_ECDH_IN_MPSL_WORK is not set
# CONFIG_BT_CTLR_LE_POWER_CONTROL is not set
# end of SoftDevice Controller

#
# BLE Libraries
#
# CONFIG_BT_GATT_POOL is not set
# CONFIG_BT_GATT_DM is not set
# CONFIG_BT_ADV_PROV is not set
# CONFIG_BT_SCAN is not set
# CONFIG_BT_CONN_CTX is not set

#
# Bluetooth Services
#
# CONFIG_BT_AMS_CLIENT is not set
# CONFIG_BT_ANCS_CLIENT is not set
# CONFIG_BT_BAS_CLIENT is not set
# CONFIG_BT_BMS is not set
# CONFIG_BT_CTS_CLIENT is not set
# CONFIG_BT_DFU_SMP is not set
# CONFIG_BT_GATTP is not set
# CONFIG_BT_HIDS is not set
# CONFIG_BT_HOGP is not set
# CONFIG_BT_LBS is not set
# CONFIG_BT_NSMS is not set
# CONFIG_BT_NUS is not set
# CONFIG_BT_NUS_CLIENT is not set
# CONFIG_BT_RSCS is not set
# CONFIG_BT_THROUGHPUT is not set
# CONFIG_BT_LATENCY is not set
# CONFIG_BT_LATENCY_CLIENT is not set
# CONFIG_BT_HRS_CLIENT is not set
# CONFIG_BT_DDFS is not set
# CONFIG_BT_MDS is not set
# CONFIG_BT_CGMS is not set
# CONFIG_BT_FAST_PAIR is not set
# end of Bluetooth Services

#
# BLE over nRF RPC
#
# CONFIG_BT_RPC_STACK is not set
CONFIG_BT_CENTRAL=y
CONFIG_BT_PERIPHERAL=y
CONFIG_BT_OBSERVER=y
CONFIG_BT_BROADCASTER=y
CONFIG_BT_CONN=y
CONFIG_BT_REMOTE_VERSION=y
CONFIG_BT_PHY_UPDATE=y
CONFIG_BT_DATA_LEN_UPDATE=y
# CONFIG_BT_EXT_ADV is not set
CONFIG_BT_BUF_ACL_TX_COUNT=7
CONFIG_BT_BUF_ACL_RX_COUNT=6
CONFIG_BT_BUF_EVT_RX_SIZE=68
CONFIG_BT_BUF_EVT_RX_COUNT=10
CONFIG_BT_BUF_EVT_DISCARDABLE_SIZE=43
CONFIG_BT_BUF_CMD_TX_SIZE=65
CONFIG_BT_HAS_HCI_VS=y
CONFIG_BT_HCI_VS=y
# CONFIG_BT_HCI_VS_EVT is not set
# CONFIG_BT_HCI_VS_FATAL_ERROR is not set
# CONFIG_BT_HCI_MESH_EXT is not set
# CONFIG_BT_WAIT_NOP is not set
CONFIG_BT_RPA=y
CONFIG_BT_ASSERT=y
CONFIG_BT_ASSERT_VERBOSE=y
# CONFIG_BT_ASSERT_PANIC is not set
CONFIG_BT_DEBUG_NONE=y
# CONFIG_BT_DEBUG_LOG is not set
# CONFIG_BT_DEBUG_MONITOR_UART is not set
# CONFIG_BT_LONG_WQ is not set
# CONFIG_BT_HCI_TX_STACK_SIZE_WITH_PROMPT is not set
CONFIG_BT_HCI_TX_PRIO=7
CONFIG_BT_HCI_RESERVE=0
# CONFIG_BT_RECV_BLOCKING is not set
# CONFIG_BT_RECV_WORKQ_SYS is not set
CONFIG_BT_RECV_WORKQ_BT=y
CONFIG_BT_RX_PRIO=8
CONFIG_BT_DRIVER_RX_HIGH_PRIO=6
# CONFIG_BT_ECC is not set
# CONFIG_BT_HOST_CCM is not set
# CONFIG_BT_LOG_SNIFFER_INFO is not set
# CONFIG_BT_TESTING is not set
# CONFIG_BT_HCI_VS_EVT_USER is not set
# end of BLE over nRF RPC
# end of Bluetooth Low Energy

#
# DFU
#
# CONFIG_DFU_MULTI_IMAGE is not set
# CONFIG_DFU_TARGET is not set
# end of DFU

# CONFIG_ESB is not set

#
# Peripheral CPU DFU (PCD)
#
# CONFIG_PCD is not set
# CONFIG_PCD_APP is not set
# CONFIG_PCD_NET is not set
# end of Peripheral CPU DFU (PCD)

#
# Networking
#

#
# Application protocols
#

#
# nRF Cloud
#

#
# Client ID (nRF Cloud Device ID)
#
CONFIG_NRF_CLOUD_CLIENT_ID_SRC_COMPILE_TIME=y
CONFIG_NRF_CLOUD_CLIENT_ID="my-client-id"
# end of Client ID (nRF Cloud Device ID)

# CONFIG_NRF_CLOUD_MQTT is not set
# CONFIG_NRF_CLOUD_FOTA is not set
# CONFIG_NRF_CLOUD_FOTA_FULL_MODEM_UPDATE is not set
# CONFIG_NRF_CLOUD_REST is not set
# CONFIG_NRF_CLOUD_ALERT is not set
CONFIG_NRF_CLOUD_LOG_OUTPUT_LEVEL=1
CONFIG_NRF_CLOUD_LOG_BUF_SIZE=256
# CONFIG_NRF_CLOUD_GATEWAY is not set
# end of nRF Cloud

# CONFIG_REST_CLIENT is not set
# CONFIG_DOWNLOAD_CLIENT is not set
# CONFIG_AWS_IOT is not set
# CONFIG_AWS_JOBS is not set
# CONFIG_AZURE_IOT_HUB is not set

#
# Self-Registration (Zi ZHu Ce)
#
# end of Self-Registration (Zi ZHu Ce)

# CONFIG_ICAL_PARSER is not set
# CONFIG_FTP_CLIENT is not set
# CONFIG_LWM2M_CLIENT_UTILS is not set
# CONFIG_WIFI_CREDENTIALS is not set
# CONFIG_WIFI_CREDENTIALS_STATIC is not set
# CONFIG_MQTT_HELPER is not set
# end of Application protocols
# end of Networking

#
# NFC
#
# CONFIG_NFC_NDEF is not set
# CONFIG_NFC_NDEF_PARSER is not set
# CONFIG_NFC_NDEF_PAYLOAD_TYPE_COMMON is not set
# CONFIG_NFC_T2T_PARSER is not set
# CONFIG_NFC_T4T_NDEF_FILE is not set
# CONFIG_NFC_T4T_ISODEP is not set
# CONFIG_NFC_T4T_APDU is not set
# CONFIG_NFC_T4T_CC_FILE is not set
# CONFIG_NFC_T4T_HL_PROCEDURE is not set
# CONFIG_NFC_PLATFORM is not set
# CONFIG_NFC_TNEP_TAG is not set
# CONFIG_NFC_TNEP_POLLER is not set
# CONFIG_NFC_TNEP_CH is not set
# end of NFC

# CONFIG_APP_EVENT_MANAGER is not set
# CONFIG_NRF_PROFILER is not set
# CONFIG_FW_INFO is not set

#
# Debug
#
# CONFIG_CPU_LOAD is not set
# CONFIG_PPI_TRACE is not set
# end of Debug

# CONFIG_SHELL_BT_NUS is not set
# CONFIG_SHELL_IPC is not set
# CONFIG_MPSL_FEM_ONLY is not set
CONFIG_MPSL_FEM_ANY_SUPPORT=y
CONFIG_MPSL_FEM_NRF21540_GPIO_SUPPORT=y
CONFIG_MPSL_FEM_NRF21540_GPIO_SPI_SUPPORT=y
CONFIG_MPSL_FEM_NCS_SUPPORTED_FEM_USED=y
CONFIG_MPSL_FEM_API_AVAILABLE=y
CONFIG_MPSL_FEM=y
# CONFIG_MPSL_FEM_NRF21540_GPIO is not set
CONFIG_MPSL_FEM_NRF21540_GPIO_SPI=y
CONFIG_MPSL_FEM_NRF21540_TX_GAIN_DB=10
CONFIG_MPSL_FEM_NRF21540_TX_GAIN_DB_POUTA=20
CONFIG_MPSL_FEM_NRF21540_TX_GAIN_DB_POUTB=10
CONFIG_MPSL_FEM_NRF21540_RX_GAIN_DB=13
# CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL is not set
CONFIG_MPSL_FEM_POWER_MODEL=y
CONFIG_MPSL_FEM_POWER_MODEL_NRF21540_USE_BUILTIN=y
CONFIG_MPSL_FEM_BUILTIN_POWER_MODEL_UPDATE_PERIOD=2000
CONFIG_MPSL_FEM_DEVICE_CONFIG_254=y
CONFIG_MPSL_THREAD_COOP_PRIO=6
CONFIG_MPSL_WORK_STACK_SIZE=1024
CONFIG_MPSL_TIMESLOT_SESSION_COUNT=0
# CONFIG_MPSL_ASSERT_HANDLER is not set

#
# Partition Manager
#
CONFIG_PARTITION_MANAGER_ENABLED=y
CONFIG_FLASH_MAP_CUSTOM=y
CONFIG_SRAM_BASE_ADDRESS=0x21000000

#
# Zephyr subsystem configurations
#
# end of Zephyr subsystem configurations

#
# NCS subsystem configurations
#
# CONFIG_PM_SINGLE_IMAGE is not set
CONFIG_PM_EXTERNAL_FLASH_BASE=0
# CONFIG_PM_OVERRIDE_EXTERNAL_DRIVER_CHECK is not set
CONFIG_PM_SRAM_BASE=0x21000000
CONFIG_PM_SRAM_SIZE=0x10000
# end of Partition Manager

#
# nRF RPC (Remote Procedure Call) library
#
# end of nRF RPC (Remote Procedure Call) library

#
# Full Modem Firmware Update Management(FMFU)
#
# end of Full Modem Firmware Update Management(FMFU)

# CONFIG_CAF is not set

#
# Nordic IEEE 802.15.4
#
# end of Nordic IEEE 802.15.4

# CONFIG_DM_MODULE is not set

#
# TF-M SPM component configs
#
CONFIG_TFM_CONN_HANDLE_MAX_NUM=8
# end of TF-M SPM component configs

#
# Libraries
#

#
# Binary libraries
#
# CONFIG_BT_LL_ACS_NRF53 is not set
# end of Binary libraries

# CONFIG_ADP536X is not set
# CONFIG_AT_MONITOR is not set
# CONFIG_LTE_LINK_CONTROL is not set
CONFIG_NRF_ACL_FLASH_REGION_SIZE=0x800
CONFIG_FPROTECT_BLOCK_SIZE=0x800
# CONFIG_FPROTECT is not set
# CONFIG_AT_CMD_CUSTOM is not set
# CONFIG_DK_LIBRARY is not set
# CONFIG_MODEM_INFO is not set
CONFIG_MULTITHREADING_LOCK=y
CONFIG_RESET_ON_FATAL_ERROR=y
# CONFIG_SMS is not set
# CONFIG_SUPL_CLIENT_LIB is not set
# CONFIG_DATE_TIME is not set
# CONFIG_HW_ID_LIBRARY is not set
# CONFIG_WAVE_GEN_LIB is not set
CONFIG_HW_UNIQUE_KEY_PARTITION_SIZE=0x800
# CONFIG_MODEM_JWT is not set
# CONFIG_QOS is not set
# CONFIG_SFLOAT is not set
# CONFIG_CONTIN_ARRAY is not set
# CONFIG_PCM_MIX is not set
# CONFIG_TONE is not set
# CONFIG_PSCM is not set
# CONFIG_DATA_FIFO is not set
# CONFIG_FEM_AL_LIB is not set
# end of Libraries

#
# Device Drivers
#
# CONFIG_BT_DRIVER_QUIRK_NO_AUTO_DLE is not set
# CONFIG_ETH_RTT is not set
# CONFIG_NRF_SW_LPUART is not set
CONFIG_NRFX_GPIOTE_NUM_OF_EVT_HANDLERS=1
# CONFIG_IPC_UART is not set
CONFIG_CLOCK_CONTROL_MPSL=y
CONFIG_SOC_FLASH_NRF_RADIO_SYNC_MPSL_TIMESLOT_SESSION_COUNT=0
# end of Device Drivers

#
# External libraries
#
# end of External libraries

#
# Test
#
CONFIG_ZTEST_MULTICORE_DEFAULT_SETTINGS=y
# CONFIG_UNITY is not set

#
# Mocks
#
# CONFIG_MOCK_NRF_MODEM_AT is not set
# end of Mocks
# end of Test
# end of Nordic nRF Connect

CONFIG_ZEPHYR_NRF_MODULE=y
# end of nrf (/home/user/ncs_v2.4.1/nrf)

#
# majipro (/home/user/ncs_v2.4.1/majipro)
#

#
# Majipro
#

#
# Libraries
#
# CONFIG_LIBMJP is not set
# CONFIG_ZMODEM is not set
# CONFIG_RTKLIB is not set
# CONFIG_LIBMJP_MBEDTLS_SUPPORT is not set
# CONFIG_LIBMJP_NETWORK_TEST is not set
# end of Libraries

# CONFIG_GPIO_ADP5587 is not set
# CONFIG_GPIO_CSSEL is not set
# CONFIG_SRAM_IS66WVS4M8ALL is not set
# CONFIG_GNSS_CXD5610 is not set

#
# External
#
# CONFIG_NNABLA_RUNTIME is not set
# end of External
# end of Majipro

CONFIG_ZEPHYR_MAJIPRO_MODULE=y
# end of majipro (/home/user/ncs_v2.4.1/majipro)

#
# hostap (/home/user/ncs_v2.4.1/modules/lib/hostap)
#
CONFIG_POSIX_MAX_FDS=4
CONFIG_ZEPHYR_HOSTAP_MODULE=y
# end of hostap (/home/user/ncs_v2.4.1/modules/lib/hostap)

#
# mcuboot (/home/user/ncs_v2.4.1/bootloader/mcuboot)
#

#
# MCUboot
#
CONFIG_BOOT_SIGNATURE_KEY_FILE=""
CONFIG_DT_FLASH_WRITE_BLOCK_SIZE=4
# end of MCUboot

CONFIG_ZEPHYR_MCUBOOT_MODULE=y
# end of mcuboot (/home/user/ncs_v2.4.1/bootloader/mcuboot)

#
# mbedtls (/home/user/ncs_v2.4.1/modules/crypto/mbedtls)
#
CONFIG_ZEPHYR_MBEDTLS_MODULE=y
CONFIG_MBEDTLS_BUILTIN=y
# CONFIG_MBEDTLS_LIBRARY is not set
# end of mbedtls (/home/user/ncs_v2.4.1/modules/crypto/mbedtls)

#
# trusted-firmware-m (/home/user/ncs_v2.4.1/modules/tee/tf-m/trusted-firmware-m)
#
# CONFIG_BOOTLOADER_MCUBOOT is not set
CONFIG_ZEPHYR_TRUSTED_FIRMWARE_M_MODULE=y
# end of trusted-firmware-m (/home/user/ncs_v2.4.1/modules/tee/tf-m/trusted-firmware-m)

#
# cjson (/home/user/ncs_v2.4.1/modules/lib/cjson)
#
CONFIG_ZEPHYR_CJSON_MODULE=y
# end of cjson (/home/user/ncs_v2.4.1/modules/lib/cjson)

#
# azure-sdk-for-c (/home/user/ncs_v2.4.1/modules/lib/azure-sdk-for-c)
#
# CONFIG_AZURE_SDK is not set
CONFIG_ZEPHYR_AZURE_SDK_FOR_C_MODULE=y
# end of azure-sdk-for-c (/home/user/ncs_v2.4.1/modules/lib/azure-sdk-for-c)

#
# cirrus-logic (/home/user/ncs_v2.4.1/modules/hal/cirrus-logic)
#
# CONFIG_HW_CODEC_CIRRUS_LOGIC is not set
CONFIG_ZEPHYR_CIRRUS_LOGIC_MODULE=y
# end of cirrus-logic (/home/user/ncs_v2.4.1/modules/hal/cirrus-logic)

#
# openthread (/home/user/ncs_v2.4.1/modules/lib/openthread)
#
# CONFIG_OPENTHREAD is not set
CONFIG_ZEPHYR_OPENTHREAD_MODULE=y
# end of openthread (/home/user/ncs_v2.4.1/modules/lib/openthread)

#
# memfault-firmware-sdk (/home/user/ncs_v2.4.1/modules/lib/memfault-firmware-sdk)
#
# CONFIG_MEMFAULT is not set
CONFIG_ZEPHYR_MEMFAULT_FIRMWARE_SDK_MODULE=y
# end of memfault-firmware-sdk (/home/user/ncs_v2.4.1/modules/lib/memfault-firmware-sdk)

#
# canopennode (/home/user/ncs_v2.4.1/modules/lib/canopennode)
#
CONFIG_ZEPHYR_CANOPENNODE_MODULE=y
# end of canopennode (/home/user/ncs_v2.4.1/modules/lib/canopennode)

#
# chre (/home/user/ncs_v2.4.1/modules/lib/chre)
#
CONFIG_ZEPHYR_CHRE_MODULE=y
# CONFIG_CHRE is not set
# end of chre (/home/user/ncs_v2.4.1/modules/lib/chre)

#
# fatfs (/home/user/ncs_v2.4.1/modules/fs/fatfs)
#
CONFIG_ZEPHYR_FATFS_MODULE=y
# end of fatfs (/home/user/ncs_v2.4.1/modules/fs/fatfs)

#
# hal_nordic (/home/user/ncs_v2.4.1/modules/hal/nordic)
#
CONFIG_ZEPHYR_HAL_NORDIC_MODULE=y
CONFIG_HAS_NORDIC_DRIVERS=y

#
# Nordic drivers
#
# CONFIG_NRF_802154_SOURCE_HAL_NORDIC is not set
# CONFIG_NRF_802154_RADIO_DRIVER is not set
# CONFIG_NRF_802154_SER_RADIO is not set
# end of Nordic drivers

CONFIG_HAS_NRFX=y

#
# nrfx drivers
#
# CONFIG_NRFX_CLOCK is not set
CONFIG_NRFX_DPPI=y
# CONFIG_NRFX_EGU0 is not set
CONFIG_NRFX_GPIOTE=y
CONFIG_NRFX_IPC=y
# CONFIG_NRFX_NVMC is not set
# CONFIG_NRFX_POWER is not set
# CONFIG_NRFX_RNG is not set
# CONFIG_NRFX_RTC0 is not set
# CONFIG_NRFX_RTC1 is not set
# CONFIG_NRFX_SPIM0 is not set
# CONFIG_NRFX_SYSTICK is not set
# CONFIG_NRFX_TEMP is not set
# CONFIG_NRFX_TIMER0 is not set
# CONFIG_NRFX_TIMER1 is not set
# CONFIG_NRFX_TIMER2 is not set
# CONFIG_NRFX_TWIM0 is not set
# CONFIG_NRFX_UARTE0 is not set
# CONFIG_NRFX_WDT0 is not set

#
# Peripheral Resource Sharing module
#
# CONFIG_NRFX_PRS_BOX_0 is not set
# CONFIG_NRFX_PRS_BOX_1 is not set
# CONFIG_NRFX_PRS_BOX_2 is not set
# CONFIG_NRFX_PRS_BOX_3 is not set
# CONFIG_NRFX_PRS_BOX_4 is not set
# end of Peripheral Resource Sharing module
# end of nrfx drivers
# end of hal_nordic (/home/user/ncs_v2.4.1/modules/hal/nordic)

#
# liblc3 (/home/user/ncs_v2.4.1/modules/lib/liblc3)
#
CONFIG_ZEPHYR_LIBLC3_MODULE=y
# end of liblc3 (/home/user/ncs_v2.4.1/modules/lib/liblc3)

#
# littlefs (/home/user/ncs_v2.4.1/modules/fs/littlefs)
#
CONFIG_ZEPHYR_LITTLEFS_MODULE=y
# end of littlefs (/home/user/ncs_v2.4.1/modules/fs/littlefs)

#
# loramac-node (/home/user/ncs_v2.4.1/modules/lib/loramac-node)
#
CONFIG_ZEPHYR_LORAMAC_NODE_MODULE=y
# CONFIG_HAS_SEMTECH_RADIO_DRIVERS is not set
# end of loramac-node (/home/user/ncs_v2.4.1/modules/lib/loramac-node)

#
# lvgl (/home/user/ncs_v2.4.1/modules/lib/gui/lvgl)
#
CONFIG_ZEPHYR_LVGL_MODULE=y
# end of lvgl (/home/user/ncs_v2.4.1/modules/lib/gui/lvgl)

#
# lz4 (/home/user/ncs_v2.4.1/modules/lib/lz4)
#
CONFIG_ZEPHYR_LZ4_MODULE=y
# CONFIG_LZ4 is not set
# end of lz4 (/home/user/ncs_v2.4.1/modules/lib/lz4)

#
# nanopb (/home/user/ncs_v2.4.1/modules/lib/nanopb)
#
CONFIG_ZEPHYR_NANOPB_MODULE=y
# CONFIG_NANOPB is not set
# end of nanopb (/home/user/ncs_v2.4.1/modules/lib/nanopb)

#
# picolibc (/home/user/ncs_v2.4.1/modules/lib/picolibc)
#
# CONFIG_PICOLIBC_MODULE is not set
CONFIG_ZEPHYR_PICOLIBC_MODULE=y
# end of picolibc (/home/user/ncs_v2.4.1/modules/lib/picolibc)

#
# segger (/home/user/ncs_v2.4.1/modules/debug/segger)
#
CONFIG_ZEPHYR_SEGGER_MODULE=y
CONFIG_HAS_SEGGER_RTT=y
# CONFIG_USE_SEGGER_RTT is not set
# end of segger (/home/user/ncs_v2.4.1/modules/debug/segger)

#
# TraceRecorder (/home/user/ncs_v2.4.1/modules/debug/TraceRecorder)
#
CONFIG_ZEPHYR_TRACERECORDER_MODULE=y
# end of TraceRecorder (/home/user/ncs_v2.4.1/modules/debug/TraceRecorder)

#
# uoscore-uedhoc (/home/user/ncs_v2.4.1/modules/lib/uoscore-uedhoc)
#
CONFIG_ZEPHYR_UOSCORE_UEDHOC_MODULE=y
# end of uoscore-uedhoc (/home/user/ncs_v2.4.1/modules/lib/uoscore-uedhoc)

#
# zcbor (/home/user/ncs_v2.4.1/modules/lib/zcbor)
#
CONFIG_ZEPHYR_ZCBOR_MODULE=y
# CONFIG_ZCBOR is not set
# end of zcbor (/home/user/ncs_v2.4.1/modules/lib/zcbor)

#
# zscilib (/home/user/ncs_v2.4.1/modules/lib/zscilib)
#
# CONFIG_ZSL is not set
CONFIG_ZEPHYR_ZSCILIB_MODULE=y
# end of zscilib (/home/user/ncs_v2.4.1/modules/lib/zscilib)

#
# nrfxlib (/home/user/ncs_v2.4.1/nrfxlib)
#

#
# Nordic nrfxlib
#
CONFIG_NRF_MODEM_SHMEM_CTRL_SIZE=0x4e8
# CONFIG_NFC_T2T_NRFXLIB is not set
# CONFIG_NFC_T4T_NRFXLIB is not set
CONFIG_MPSL=y
CONFIG_MPSL_BUILD_TYPE_LIB=y

#
# Crypto libraries for nRF5x SOCs.
#
CONFIG_NRFXLIB_CRYPTO=y
CONFIG_NRF_OBERON=y
# CONFIG_NRF_CC310_BL is not set
# end of Crypto libraries for nRF5x SOCs.

#
# nrf_security module
#
# CONFIG_NRF_SECURITY is not set
# end of nrf_security module

# CONFIG_NRF_RPC is not set
CONFIG_NRF_802154_SOURCE_NRFXLIB=y
# CONFIG_GZLL is not set
# CONFIG_NRF_DM is not set
# CONFIG_LC3_PLC_DISABLED is not set
CONFIG_LC3_ENC_CHAN_MAX=1
CONFIG_LC3_DEC_CHAN_MAX=1

#
# Encoder sample rates
#
CONFIG_LC3_ENC_SAMPLE_RATE_8KHZ_SUPPORT=y
CONFIG_LC3_ENC_SAMPLE_RATE_16KHZ_SUPPORT=y
CONFIG_LC3_ENC_SAMPLE_RATE_24KHZ_SUPPORT=y
CONFIG_LC3_ENC_SAMPLE_RATE_32KHZ_SUPPORT=y
CONFIG_LC3_ENC_SAMPLE_RATE_441KHZ_SUPPORT=y
CONFIG_LC3_ENC_SAMPLE_RATE_48KHZ_SUPPORT=y
# end of Encoder sample rates

#
# Decoder sample rates
#
CONFIG_LC3_DEC_SAMPLE_RATE_8KHZ_SUPPORT=y
CONFIG_LC3_DEC_SAMPLE_RATE_16KHZ_SUPPORT=y
CONFIG_LC3_DEC_SAMPLE_RATE_24KHZ_SUPPORT=y
CONFIG_LC3_DEC_SAMPLE_RATE_32KHZ_SUPPORT=y
CONFIG_LC3_DEC_SAMPLE_RATE_441KHZ_SUPPORT=y
CONFIG_LC3_DEC_SAMPLE_RATE_48KHZ_SUPPORT=y
# end of Decoder sample rates

# CONFIG_NRF_FUEL_GAUGE is not set
# end of Nordic nrfxlib

CONFIG_ZEPHYR_NRFXLIB_MODULE=y
# end of nrfxlib (/home/user/ncs_v2.4.1/nrfxlib)

#
# connectedhomeip (/home/user/ncs_v2.4.1/modules/lib/matter)
#
# CONFIG_CHIP is not set
# CONFIG_CHIP_LOG_SIZE_OPTIMIZATION is not set
CONFIG_ZEPHYR_CONNECTEDHOMEIP_MODULE=y
# end of connectedhomeip (/home/user/ncs_v2.4.1/modules/lib/matter)

#
# Optional modules. Make sure they're installed, via the project manifest.
#
CONFIG_HAS_CMSIS_CORE=y
CONFIG_HAS_CMSIS_CORE_M=y
# CONFIG_CMSIS_DSP is not set
# CONFIG_CMSIS_NN is not set
CONFIG_LIBMETAL=y
CONFIG_LIBMETAL_SRC_PATH="libmetal"
# CONFIG_LVGL is not set
# CONFIG_HAS_MEC_HAL is not set
# CONFIG_HAS_MPFS_HAL is not set
CONFIG_OPENAMP=y
CONFIG_OPENAMP_SRC_PATH="open-amp"
CONFIG_OPENAMP_MASTER=y
CONFIG_OPENAMP_SLAVE=y
# CONFIG_SOF is not set
# CONFIG_MIPI_SYST_LIB is not set
# CONFIG_HAS_TELINK_DRIVERS is not set
# CONFIG_TINYCRYPT_CTR_PRNG is not set
# CONFIG_TINYCRYPT_SHA256 is not set
# CONFIG_TINYCRYPT_ECC_DH is not set
# CONFIG_TINYCRYPT_ECC_DSA is not set
CONFIG_TINYCRYPT_AES=y
# CONFIG_TINYCRYPT_AES_CBC is not set
# CONFIG_TINYCRYPT_AES_CTR is not set
# CONFIG_TINYCRYPT_AES_CCM is not set
# CONFIG_TINYCRYPT_AES_CMAC is not set
# CONFIG_MCUBOOT_BOOTUTIL_LIB is not set

#
# Unavailable modules, please install those via the project manifest.
#

#
# hal_gigadevice module not available.
#

#
# Trusted-firmware-a module not available.
#

#
# THRIFT module not available.
#
# end of Modules

CONFIG_BOARD_REVISION=""
# CONFIG_NET_DRIVERS is not set
CONFIG_BOARD_NRF5340DK_NRF5340_CPUNET=y

#
# Board Options
#
CONFIG_DOMAIN_CPUAPP_BOARD="nrf5340dk_nrf5340_cpuapp"
# end of Board Options

# CONFIG_SOC_SERIES_BEETLE is not set
# CONFIG_SOC_SERIES_ARM_DESIGNSTART is not set
# CONFIG_SOC_SERIES_FVP_AEMV8R_AARCH32 is not set
# CONFIG_SOC_SERIES_MPS2 is not set
# CONFIG_SOC_SERIES_MPS3 is not set
# CONFIG_SOC_SERIES_MUSCA_B1 is not set
# CONFIG_SOC_SERIES_MUSCA_S1 is not set
# CONFIG_SOC_SERIES_AST10X0 is not set
# CONFIG_SOC_SERIES_SAM3X is not set
# CONFIG_SOC_SERIES_SAM4E is not set
# CONFIG_SOC_SERIES_SAM4L is not set
# CONFIG_SOC_SERIES_SAM4S is not set
# CONFIG_SOC_SERIES_SAME70 is not set
# CONFIG_SOC_SERIES_SAMV71 is not set
# CONFIG_SOC_SERIES_SAMC20 is not set
# CONFIG_SOC_SERIES_SAMC21 is not set
# CONFIG_SOC_SERIES_SAMD20 is not set
# CONFIG_SOC_SERIES_SAMD21 is not set
# CONFIG_SOC_SERIES_SAMD51 is not set
# CONFIG_SOC_SERIES_SAME51 is not set
# CONFIG_SOC_SERIES_SAME53 is not set
# CONFIG_SOC_SERIES_SAME54 is not set
# CONFIG_SOC_SERIES_SAML21 is not set
# CONFIG_SOC_SERIES_SAMR21 is not set
# CONFIG_SOC_SERIES_SAMR34 is not set
# CONFIG_SOC_SERIES_SAMR35 is not set
# CONFIG_SOC_SERIES_VALKYRIE is not set
# CONFIG_SOC_SERIES_VIPER is not set
# CONFIG_SOC_SERIES_PSOC62 is not set
# CONFIG_SOC_SERIES_PSOC63 is not set
# CONFIG_SOC_SERIES_GD32A50X is not set
# CONFIG_SOC_SERIES_GD32E10X is not set
# CONFIG_SOC_SERIES_GD32E50X is not set
# CONFIG_SOC_SERIES_GD32F3X0 is not set
# CONFIG_SOC_SERIES_GD32F403 is not set
# CONFIG_SOC_SERIES_GD32F4XX is not set
# CONFIG_SOC_SERIES_GD32L23X is not set
# CONFIG_SOC_SERIES_PSOC_60 is not set
# CONFIG_SOC_SERIES_PSOC_61 is not set
# CONFIG_SOC_SERIES_PSOC_62 is not set
# CONFIG_SOC_SERIES_PSOC_63 is not set
# CONFIG_SOC_SERIES_PSOC_64 is not set
# CONFIG_SOC_SERIES_XMC_4XXX is not set
# CONFIG_SOC_SERIES_CYCLONE5 is not set
# CONFIG_SOC_SERIES_MEC1501X is not set
# CONFIG_SOC_SERIES_MEC1701X is not set
# CONFIG_SOC_SERIES_MEC172X is not set
# CONFIG_SOC_SERIES_NRF51X is not set
# CONFIG_SOC_SERIES_NRF52X is not set
CONFIG_SOC_SERIES_NRF53X=y
# CONFIG_SOC_SERIES_NRF91X is not set
# CONFIG_SOC_SERIES_NPCX7 is not set
# CONFIG_SOC_SERIES_NPCX9 is not set
# CONFIG_SOC_SERIES_M48X is not set
# CONFIG_SOC_SERIES_IMX_6X_M4 is not set
# CONFIG_SOC_SERIES_IMX7_M4 is not set
# CONFIG_SOC_SERIES_IMX8ML_M7 is not set
# CONFIG_SOC_SERIES_IMX8MM_M4 is not set
# CONFIG_SOC_SERIES_IMX8MQ_M4 is not set
# CONFIG_SOC_SERIES_IMX_RT is not set
# CONFIG_SOC_SERIES_IMX_RT5XX is not set
# CONFIG_SOC_SERIES_IMX_RT6XX is not set
# CONFIG_SOC_SERIES_KINETIS_K2X is not set
# CONFIG_SOC_SERIES_KINETIS_K6X is not set
# CONFIG_SOC_SERIES_KINETIS_K8X is not set
# CONFIG_SOC_SERIES_KINETIS_KE1XF is not set
# CONFIG_SOC_SERIES_KINETIS_KL2X is not set
# CONFIG_SOC_SERIES_KINETIS_KV5X is not set
# CONFIG_SOC_SERIES_KINETIS_KWX is not set
# CONFIG_SOC_SERIES_LPC11U6X is not set
# CONFIG_SOC_SERIES_LPC51U68 is not set
# CONFIG_SOC_SERIES_LPC54XXX is not set
# CONFIG_SOC_SERIES_LPC55XXX is not set
# CONFIG_SOC_SERIES_S32ZE_R52 is not set
# CONFIG_SOC_EOS_S3 is not set
# CONFIG_SOC_SERIES_RCAR_GEN3 is not set
# CONFIG_SOC_SERIES_DA1469X is not set
# CONFIG_SOC_SERIES_RP2XXX is not set
# CONFIG_SOC_SERIES_EFM32GG11B is not set
# CONFIG_SOC_SERIES_EFM32HG is not set
# CONFIG_SOC_SERIES_EFM32JG12B is not set
# CONFIG_SOC_SERIES_EFM32PG12B is not set
# CONFIG_SOC_SERIES_EFM32PG1B is not set
# CONFIG_SOC_SERIES_EFM32WG is not set
# CONFIG_SOC_SERIES_EFR32BG13P is not set
# CONFIG_SOC_SERIES_EFR32BG22 is not set
# CONFIG_SOC_SERIES_EFR32FG13P is not set
# CONFIG_SOC_SERIES_EFR32FG1P is not set
# CONFIG_SOC_SERIES_EFR32MG12P is not set
# CONFIG_SOC_SERIES_EFR32MG21 is not set
# CONFIG_SOC_SERIES_EFR32MG24 is not set
# CONFIG_SOC_SERIES_STM32C0X is not set
# CONFIG_SOC_SERIES_STM32F0X is not set
# CONFIG_SOC_SERIES_STM32F1X is not set
# CONFIG_SOC_SERIES_STM32F2X is not set
# CONFIG_SOC_SERIES_STM32F3X is not set
# CONFIG_SOC_SERIES_STM32F4X is not set
# CONFIG_SOC_SERIES_STM32F7X is not set
# CONFIG_SOC_SERIES_STM32G0X is not set
# CONFIG_SOC_SERIES_STM32G4X is not set
# CONFIG_SOC_SERIES_STM32H5X is not set
# CONFIG_SOC_SERIES_STM32H7X is not set
# CONFIG_SOC_SERIES_STM32L0X is not set
# CONFIG_SOC_SERIES_STM32L1X is not set
# CONFIG_SOC_SERIES_STM32L4X is not set
# CONFIG_SOC_SERIES_STM32L5X is not set
# CONFIG_SOC_SERIES_STM32MP1X is not set
# CONFIG_SOC_SERIES_STM32U5X is not set
# CONFIG_SOC_SERIES_STM32WBX is not set
# CONFIG_SOC_SERIES_STM32WLX is not set
# CONFIG_SOC_TI_LM3S6965 is not set
# CONFIG_SOC_SERIES_CC13X2_CC26X2 is not set
# CONFIG_SOC_SERIES_CC13X2X7_CC26X2X7 is not set
# CONFIG_SOC_SERIES_CC32XX is not set
# CONFIG_SOC_SERIES_MSP432P4XX is not set
# CONFIG_SOC_SERIES_XILINX_XC7ZXXX is not set
# CONFIG_SOC_SERIES_XILINX_XC7ZXXXS is not set
# CONFIG_SOC_XILINX_ZYNQMP_RPU is not set

#
# Hardware Configuration
#
CONFIG_CPU_HAS_ARM_MPU=y
CONFIG_HAS_SWO=y
CONFIG_SOC_FAMILY="nordic_nrf"
CONFIG_SOC_FAMILY_NRF=y
CONFIG_HAS_HW_NRF_ACL=y
CONFIG_HAS_HW_NRF_CCM=y
CONFIG_HAS_HW_NRF_CCM_LFLEN_8BIT=y
CONFIG_HAS_HW_NRF_CLOCK=y
CONFIG_HAS_HW_NRF_DPPIC=y
CONFIG_HAS_HW_NRF_ECB=y
CONFIG_HAS_HW_NRF_EGU0=y
CONFIG_HAS_HW_NRF_GPIO0=y
CONFIG_HAS_HW_NRF_GPIO1=y
CONFIG_HAS_HW_NRF_GPIOTE=y
CONFIG_HAS_HW_NRF_IPC=y
CONFIG_HAS_HW_NRF_NVMC_PE=y
CONFIG_HAS_HW_NRF_POWER=y
CONFIG_HAS_HW_NRF_RADIO_BLE_2M=y
CONFIG_HAS_HW_NRF_RADIO_BLE_CODED=y
CONFIG_HAS_HW_NRF_RADIO_DFE=y
CONFIG_HAS_HW_NRF_RADIO_IEEE802154=y
CONFIG_HAS_HW_NRF_RNG=y
CONFIG_HAS_HW_NRF_SPIM0=y
CONFIG_HAS_HW_NRF_SWI0=y
CONFIG_HAS_HW_NRF_SWI1=y
CONFIG_HAS_HW_NRF_SWI2=y
CONFIG_HAS_HW_NRF_SWI3=y
CONFIG_HAS_HW_NRF_TEMP=y
CONFIG_HAS_HW_NRF_UARTE0=y
CONFIG_HAS_HW_NRF_VMC=y
CONFIG_HAS_HW_NRF_WDT0=y
CONFIG_SOC_NRF5340_CPUNET=y
# CONFIG_SOC_NRF5340_CPUAPP_QKAA is not set
CONFIG_SOC_NRF5340_CPUNET_QKAA=y
CONFIG_SOC_NRF53_ANOMALY_160_WORKAROUND_NEEDED=y
CONFIG_SOC_NRF53_ANOMALY_160_WORKAROUND=y
CONFIG_NRF_ENABLE_CACHE=y
# CONFIG_NRF53_SYNC_RTC is not set
CONFIG_NRF_RTC_TIMER_USER_CHAN_COUNT=0
CONFIG_NRF_SOC_SECURE_SUPPORTED=y
CONFIG_NRF_APPROTECT_USE_UICR=y
# CONFIG_NRF_APPROTECT_LOCK is not set
# CONFIG_NRF_APPROTECT_USER_HANDLING is not set
# CONFIG_NRF_TRACE_PORT is not set
# CONFIG_BUILD_OUTPUT_INFO_HEADER is not set
# end of Hardware Configuration

CONFIG_SOC_COMPATIBLE_NRF=y

#
# ARM Options
#
CONFIG_ARCH="arm"
CONFIG_CPU_CORTEX=y
# CONFIG_CODE_DATA_RELOCATION_SRAM is not set
CONFIG_ARM_ON_ENTER_CPU_IDLE_HOOK=y
CONFIG_ARM_ON_EXIT_CPU_IDLE=y
CONFIG_CPU_CORTEX_M=y
# CONFIG_ARM_ZIMAGE_HEADER is not set
CONFIG_ISA_THUMB2=y
CONFIG_ASSEMBLER_ISA_THUMB2=y
CONFIG_COMPILER_ISA_THUMB2=y
CONFIG_STACK_ALIGN_DOUBLE_WORD=y
# CONFIG_RUNTIME_NMI is not set
CONFIG_FAULT_DUMP=2
CONFIG_BUILTIN_STACK_GUARD=y
CONFIG_ARM_STACK_PROTECTION=y
CONFIG_CPU_CORTEX_M33=y
CONFIG_CPU_CORTEX_M_HAS_SYSTICK=y
CONFIG_CPU_CORTEX_M_HAS_DWT=y
CONFIG_CPU_CORTEX_M_HAS_BASEPRI=y
CONFIG_CPU_CORTEX_M_HAS_VTOR=y
CONFIG_CPU_CORTEX_M_HAS_SPLIM=y
CONFIG_CPU_CORTEX_M_HAS_PROGRAMMABLE_FAULT_PRIOS=y
CONFIG_CPU_CORTEX_M_HAS_CMSE=y
CONFIG_ARMV7_M_ARMV8_M_MAINLINE=y
CONFIG_ARMV8_M_MAINLINE=y

#
# ARM Cortex-M0/M0+/M1/M3/M4/M7/M23/M33 options
#
CONFIG_GEN_ISR_TABLES=y
CONFIG_ZERO_LATENCY_IRQS=y
CONFIG_ZERO_LATENCY_LEVELS=1
# CONFIG_SW_VECTOR_RELAY is not set
# CONFIG_CORTEX_M_DWT is not set
# CONFIG_CORTEX_M_DEBUG_MONITOR_HOOK is not set
# CONFIG_TRAP_UNALIGNED_ACCESS is not set
# end of ARM Cortex-M0/M0+/M1/M3/M4/M7/M23/M33 options

CONFIG_NULL_POINTER_EXCEPTION_DETECTION_NONE=y
# CONFIG_NULL_POINTER_EXCEPTION_DETECTION_DWT is not set
# CONFIG_NULL_POINTER_EXCEPTION_DETECTION_MPU is not set
CONFIG_GEN_IRQ_VECTOR_TABLE=y
CONFIG_ARM_MPU=y
CONFIG_ARM_MPU_REGION_MIN_ALIGN_AND_SIZE=32
# CONFIG_MPU_STACK_GUARD is not set
# CONFIG_MPU_ALLOW_FLASH_WRITE is not set
# CONFIG_MPU_DISABLE_BACKGROUND_MAP is not set
# CONFIG_CUSTOM_SECTION_ALIGN is not set
CONFIG_CUSTOM_SECTION_MIN_ALIGN_SIZE=32
# end of ARM Options

CONFIG_ARM=y
CONFIG_ARCH_IS_SET=y

#
# General Architecture Options
#
# CONFIG_SEMIHOST is not set
CONFIG_LITTLE_ENDIAN=y
CONFIG_HW_STACK_PROTECTION=y
# CONFIG_USERSPACE is not set
CONFIG_KOBJECT_TEXT_AREA=256
CONFIG_KOBJECT_DATA_AREA_RESERVE_EXTRA_PERCENT=100
CONFIG_KOBJECT_RODATA_AREA_EXTRA_BYTES=16
CONFIG_GEN_PRIV_STACKS=y
# CONFIG_STACK_GROWS_UP is not set

#
# Interrupt Configuration
#
# CONFIG_DYNAMIC_INTERRUPTS is not set
CONFIG_ARCH_IRQ_VECTOR_TABLE_ALIGN=4
CONFIG_IRQ_VECTOR_TABLE_JUMP_BY_ADDRESS=y
# CONFIG_IRQ_VECTOR_TABLE_JUMP_BY_CODE is not set
CONFIG_GEN_SW_ISR_TABLE=y
CONFIG_ARCH_SW_ISR_TABLE_ALIGN=4
CONFIG_GEN_IRQ_START_VECTOR=0
# CONFIG_EXTRA_EXCEPTION_INFO is not set
# CONFIG_SIMPLIFIED_EXCEPTION_CODES is not set
# end of Interrupt Configuration
# end of General Architecture Options

CONFIG_ARCH_HAS_SINGLE_THREAD_SUPPORT=y
CONFIG_ARCH_HAS_TIMING_FUNCTIONS=y
CONFIG_ARCH_HAS_STACK_PROTECTION=y
CONFIG_ARCH_HAS_USERSPACE=y
CONFIG_ARCH_HAS_EXECUTABLE_PAGE_BIT=y
CONFIG_ARCH_HAS_RAMFUNC_SUPPORT=y
CONFIG_ARCH_HAS_NESTED_EXCEPTION_DETECTION=y
CONFIG_ARCH_SUPPORTS_COREDUMP=y
CONFIG_ARCH_SUPPORTS_ARCH_HW_INIT=y
CONFIG_ARCH_HAS_EXTRA_EXCEPTION_INFO=y
CONFIG_ARCH_HAS_THREAD_LOCAL_STORAGE=y
CONFIG_ARCH_HAS_SUSPEND_TO_RAM=y
CONFIG_ARCH_HAS_THREAD_ABORT=y
CONFIG_ARCH_HAS_CODE_DATA_RELOCATION=y
CONFIG_CPU_HAS_MPU=y
CONFIG_MPU=y
CONFIG_MPU_REQUIRES_NON_OVERLAPPING_REGIONS=y
CONFIG_MPU_GAP_FILLING=y
CONFIG_SRAM_REGION_PERMISSIONS=y

#
# Floating Point Options
#
# end of Floating Point Options

#
# Cache Options
#
# end of Cache Options

CONFIG_TOOLCHAIN_HAS_BUILTIN_FFS=y

#
# General Kernel Options
#
CONFIG_MULTITHREADING=y
CONFIG_NUM_COOP_PRIORITIES=16
CONFIG_NUM_PREEMPT_PRIORITIES=15
CONFIG_MAIN_THREAD_PRIORITY=0
CONFIG_COOP_ENABLED=y
CONFIG_PREEMPT_ENABLED=y
CONFIG_PRIORITY_CEILING=-127
# CONFIG_SCHED_DEADLINE is not set
# CONFIG_SCHED_CPU_MASK is not set
CONFIG_IDLE_STACK_SIZE=256
CONFIG_ISR_STACK_SIZE=2048
CONFIG_THREAD_STACK_INFO=y
# CONFIG_THREAD_CUSTOM_DATA is not set
CONFIG_ERRNO=y
CONFIG_SCHED_DUMB=y
# CONFIG_SCHED_SCALABLE is not set
# CONFIG_SCHED_MULTIQ is not set
# CONFIG_WAITQ_SCALABLE is not set
CONFIG_WAITQ_DUMB=y

#
# Kernel Debugging and Metrics
#
CONFIG_BOOT_BANNER=y
CONFIG_BOOT_DELAY=0
# CONFIG_THREAD_MONITOR is not set
# CONFIG_THREAD_NAME is not set
# CONFIG_THREAD_RUNTIME_STATS is not set
# end of Kernel Debugging and Metrics

#
# Work Queue Options
#
CONFIG_SYSTEM_WORKQUEUE_PRIORITY=-1
# CONFIG_SYSTEM_WORKQUEUE_NO_YIELD is not set
# end of Work Queue Options

#
# Atomic Operations
#
CONFIG_ATOMIC_OPERATIONS_BUILTIN=y
# end of Atomic Operations

#
# Timer API Options
#
CONFIG_TIMESLICING=y
CONFIG_TIMESLICE_SIZE=0
CONFIG_TIMESLICE_PRIORITY=0
# CONFIG_TIMESLICE_PER_THREAD is not set
CONFIG_POLL=y
# end of Timer API Options

#
# Other Kernel Object Options
#
# CONFIG_MEM_SLAB_TRACE_MAX_UTILIZATION is not set
CONFIG_NUM_MBOX_ASYNC_MSGS=10
# CONFIG_EVENTS is not set
# CONFIG_PIPES is not set
CONFIG_KERNEL_MEM_POOL=y
# end of Other Kernel Object Options

CONFIG_ARCH_HAS_CUSTOM_SWAP_TO_MAIN=y
CONFIG_SWAP_NONATOMIC=y
CONFIG_SYS_CLOCK_EXISTS=y
CONFIG_TIMEOUT_64BIT=y
CONFIG_SYS_CLOCK_MAX_TIMEOUT_DAYS=365
CONFIG_XIP=y

#
# Initialization Priorities
#
CONFIG_KERNEL_INIT_PRIORITY_OBJECTS=30
CONFIG_KERNEL_INIT_PRIORITY_DEFAULT=40
CONFIG_KERNEL_INIT_PRIORITY_DEVICE=50
CONFIG_APPLICATION_INIT_PRIORITY=90
# end of Initialization Priorities

#
# Security Options
#
# CONFIG_STACK_CANARIES is not set
CONFIG_STACK_POINTER_RANDOM=0
# end of Security Options

#
# SMP Options
#
CONFIG_MP_NUM_CPUS=1
# end of SMP Options

CONFIG_TICKLESS_KERNEL=y
CONFIG_TOOLCHAIN_SUPPORTS_THREAD_LOCAL_STORAGE=y
# CONFIG_THREAD_LOCAL_STORAGE is not set
# end of General Kernel Options

#
# Device Options
#
# end of Device Options

#
# Virtual Memory Support
#
# end of Virtual Memory Support

#
# Device Drivers
#
# CONFIG_ADC is not set
# CONFIG_AUDIO is not set
# CONFIG_BBRAM is not set
# CONFIG_CACHE is not set
# CONFIG_CAN is not set
CONFIG_CLOCK_CONTROL_NRF_FORCE_ALT=y
CONFIG_CLOCK_CONTROL_NRF=y
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC is not set
CONFIG_CLOCK_CONTROL_NRF_K32SRC_XTAL=y
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_SYNTH is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_500PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_250PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_150PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_100PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_75PPM is not set
CONFIG_CLOCK_CONTROL_NRF_K32SRC_50PPM=y
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_30PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_20PPM is not set
CONFIG_CLOCK_CONTROL_NRF_ACCURACY=50
CONFIG_CONSOLE=y
CONFIG_CONSOLE_INPUT_MAX_LINE_LEN=128
CONFIG_CONSOLE_HAS_DRIVER=y
# CONFIG_CONSOLE_HANDLER is not set
CONFIG_CONSOLE_INIT_PRIORITY=60
CONFIG_UART_CONSOLE=y
# CONFIG_UART_CONSOLE_DEBUG_SERVER_HOOKS is not set
# CONFIG_UART_CONSOLE_MCUMGR is not set
# CONFIG_RAM_CONSOLE is not set
# CONFIG_IPM_CONSOLE_SENDER is not set
# CONFIG_IPM_CONSOLE_RECEIVER is not set
# CONFIG_UART_MCUMGR is not set
# CONFIG_GSM_MUX is not set
# CONFIG_EFI_CONSOLE is not set
# CONFIG_COREDUMP_DEVICE is not set
# CONFIG_COUNTER is not set
# CONFIG_CRYPTO is not set
# CONFIG_DAC is not set
# CONFIG_DAI is not set
# CONFIG_DISK_DRIVERS is not set
# CONFIG_DMA is not set
# CONFIG_EDAC is not set
# CONFIG_EEPROM is not set
CONFIG_ENTROPY_INIT_PRIORITY=50
CONFIG_ENTROPY_NRF5_RNG=y
# CONFIG_ENTROPY_NRF5_BIAS_CORRECTION is not set
CONFIG_ENTROPY_NRF5_THR_POOL_SIZE=8
CONFIG_ENTROPY_NRF5_THR_THRESHOLD=4
CONFIG_ENTROPY_NRF5_ISR_POOL_SIZE=16
CONFIG_ENTROPY_NRF5_ISR_THRESHOLD=12
CONFIG_ENTROPY_HAS_DRIVER=y
# CONFIG_ESPI is not set
# CONFIG_FLASH is not set
# CONFIG_FPGA is not set
# CONFIG_FUEL_GAUGE is not set
# CONFIG_GPIO_GET_DIRECTION is not set
# CONFIG_GPIO_GET_CONFIG is not set
# CONFIG_GPIO_HOGS is not set
# CONFIG_GPIO_ENABLE_DISABLE_INTERRUPT is not set
CONFIG_GPIO_NRFX=y
# CONFIG_HWINFO is not set
# CONFIG_I2S is not set
# CONFIG_I3C is not set
# CONFIG_SMBUS is not set

#
# Interrupt controller drivers
#
CONFIG_INTC_INIT_PRIORITY=40
# CONFIG_MULTI_LEVEL_INTERRUPTS is not set
# CONFIG_INTC_ESP32 is not set
# end of Interrupt controller drivers

# CONFIG_IPM is not set
# CONFIG_LED is not set
# CONFIG_LED_STRIP is not set
# CONFIG_LORA is not set
CONFIG_MBOX=y
CONFIG_MBOX_INIT_PRIORITY=50
# CONFIG_MDIO is not set
# CONFIG_MIPI_DSI is not set

#
# Miscellaneous Drivers
#
# CONFIG_GROVE_LCD_RGB is not set
# end of Miscellaneous Drivers

# CONFIG_MM_DRV is not set
# CONFIG_NEURAL_NET_ACCEL is not set
# CONFIG_PCIE is not set
# CONFIG_PCIE_ENDPOINT is not set
# CONFIG_PECI is not set
CONFIG_PINCTRL_STORE_REG=y
# CONFIG_PINCTRL_DYNAMIC is not set
CONFIG_PINCTRL_NRF=y
# CONFIG_PM_CPU_OPS is not set
# CONFIG_POWER_DOMAIN is not set
# CONFIG_PS2 is not set
# CONFIG_PTP_CLOCK is not set
# CONFIG_PWM is not set
# CONFIG_RETAINED_MEM is not set
# CONFIG_RTC is not set
# CONFIG_SDHC is not set

#
# Capabilities
#
CONFIG_SERIAL_HAS_DRIVER=y
CONFIG_SERIAL_SUPPORT_ASYNC=y
CONFIG_SERIAL_SUPPORT_INTERRUPT=y
CONFIG_UART_USE_RUNTIME_CONFIGURE=y
# CONFIG_UART_ASYNC_API is not set
# CONFIG_UART_LINE_CTRL is not set
# CONFIG_UART_DRV_CMD is not set
# CONFIG_UART_WIDE_DATA is not set
# CONFIG_UART_PIPE is not set

#
# Serial Drivers
#
CONFIG_UART_NRFX=y
CONFIG_UART_0_NRF_UARTE=y
CONFIG_UART_0_ENHANCED_POLL_OUT=y
# CONFIG_UART_0_NRF_PARITY_BIT is not set
CONFIG_UART_0_NRF_TX_BUFFER_SIZE=32
CONFIG_UART_ENHANCED_POLL_OUT=y
CONFIG_NRF_UARTE_PERIPHERAL=y
# CONFIG_SYSCON is not set

#
# Timer drivers
#
# CONFIG_TIMER_READS_ITS_FREQUENCY_AT_RUNTIME is not set
# CONFIG_SYSTEM_CLOCK_SLOPPY_IDLE is not set
CONFIG_SYSTEM_CLOCK_INIT_PRIORITY=0
CONFIG_TICKLESS_CAPABLE=y
CONFIG_SYSTEM_TIMER_HAS_DISABLE_SUPPORT=y
CONFIG_NRF_RTC_TIMER_LOCK_ZERO_LATENCY_IRQS=y
# CONFIG_NRF_RTC_TIMER_TRIGGER_OVERFLOW is not set
# CONFIG_SYSTEM_CLOCK_NO_WAIT is not set
# CONFIG_SYSTEM_CLOCK_WAIT_FOR_AVAILABILITY is not set
CONFIG_SYSTEM_CLOCK_WAIT_FOR_STABILITY=y
# end of Timer drivers

# CONFIG_USB_BC12 is not set
# CONFIG_UDC_DRIVER is not set
# CONFIG_UVB is not set
# CONFIG_USB_DEVICE_DRIVER is not set
# CONFIG_USBC_TCPC_DRIVER is not set
# CONFIG_USBC_VBUS_DRIVER is not set
# CONFIG_VIDEO is not set
# CONFIG_VIRTUALIZATION is not set
# CONFIG_W1 is not set
# end of Device Drivers

#
# C Library
#
CONFIG_SUPPORT_MINIMAL_LIBC=y
CONFIG_PICOLIBC_SUPPORTED=y
CONFIG_MINIMAL_LIBC=y
# CONFIG_PICOLIBC is not set
# CONFIG_NEWLIB_LIBC is not set
# CONFIG_EXTERNAL_LIBC is not set
CONFIG_HAS_NEWLIB_LIBC_NANO=y
CONFIG_MINIMAL_LIBC_NON_REENTRANT_FUNCTIONS=y
CONFIG_MINIMAL_LIBC_MALLOC=y
CONFIG_MINIMAL_LIBC_MALLOC_ARENA_SIZE=0
CONFIG_MINIMAL_LIBC_CALLOC=y
CONFIG_MINIMAL_LIBC_REALLOCARRAY=y
# CONFIG_MINIMAL_LIBC_LL_PRINTF is not set
CONFIG_MINIMAL_LIBC_OPTIMIZE_STRING_FOR_SIZE=y
# CONFIG_MINIMAL_LIBC_RAND is not set
CONFIG_MINIMAL_LIBC_TIME=y
# CONFIG_MINIMAL_LIBC_STRING_ERROR_TABLE is not set
CONFIG_STDOUT_CONSOLE=y
CONFIG_NEED_LIBC_MEM_PARTITION=y
# end of C Library

#
# C++ Language Support
#
# CONFIG_CPP is not set

#
# Deprecated
#
# CONFIG_CPLUSPLUS is not set
# CONFIG_LIB_CPLUSPLUS is not set
# end of Deprecated
# end of C++ Language Support

#
# Additional libraries
#

#
# Hash Function Support
#
# CONFIG_SYS_HASH_FUNC32 is not set
# end of Hash Function Support

#
# Hashmap (Hash Table) Support
#
# CONFIG_SYS_HASH_MAP is not set
# end of Hashmap (Hash Table) Support

#
# OS Support Library
#
# CONFIG_JSON_LIBRARY is not set
# CONFIG_RING_BUFFER is not set
CONFIG_NOTIFY=y
# CONFIG_BASE64 is not set
CONFIG_CRC=y
# CONFIG_PRINTK_SYNC is not set
# CONFIG_MPSC_PBUF is not set
CONFIG_ONOFF=y
# CONFIG_SPSC_PBUF is not set
# CONFIG_SHARED_MULTI_HEAP is not set
# CONFIG_WINSTREAM is not set
CONFIG_REBOOT=y
# CONFIG_UTF8 is not set
CONFIG_CBPRINTF_COMPLETE=y
# CONFIG_CBPRINTF_NANO is not set
CONFIG_CBPRINTF_FULL_INTEGRAL=y
# CONFIG_CBPRINTF_REDUCED_INTEGRAL is not set
# CONFIG_CBPRINTF_FP_SUPPORT is not set
# CONFIG_CBPRINTF_FP_A_SUPPORT is not set
# CONFIG_CBPRINTF_FP_ALWAYS_A is not set
CONFIG_CBPRINTF_N_SPECIFIER=y
# CONFIG_CBPRINTF_LIBC_SUBSTS is not set
# CONFIG_CBPRINTF_PACKAGE_LONGDOUBLE is not set
# CONFIG_CBPRINTF_STATIC_PACKAGE_CHECK_ALIGNMENT is not set

#
# Heap and Memory Allocation
#
# CONFIG_SYS_HEAP_VALIDATE is not set
CONFIG_SYS_HEAP_ALLOC_LOOPS=3
# CONFIG_SYS_HEAP_RUNTIME_STATS is not set
# CONFIG_SYS_HEAP_LISTENER is not set
CONFIG_SYS_HEAP_SMALL_ONLY=y
# CONFIG_SYS_HEAP_BIG_ONLY is not set
# CONFIG_SYS_HEAP_AUTO is not set
# CONFIG_SYS_MEM_BLOCKS is not set
# end of Heap and Memory Allocation
# end of OS Support Library

# CONFIG_POSIX_API is not set
# CONFIG_POSIX_CLOCK is not set
CONFIG_MAX_TIMER_COUNT=5
CONFIG_TIMER_CREATE_WAIT=100
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_EVENTFD is not set
# CONFIG_FNMATCH is not set
# CONFIG_OPENAMP_RSC_TABLE is not set
# CONFIG_SMF is not set
# end of Additional libraries

#
# Subsystems and OS Services
#
CONFIG_BT=y
CONFIG_BT_HCI=y
# CONFIG_BT_CUSTOM is not set
CONFIG_BT_HCI_RAW=y
# CONFIG_BT_HCI_RAW_H4 is not set
CONFIG_BT_HCI_RAW_RESERVE=1
# CONFIG_BT_HCI_RAW_CMD_EXT is not set
CONFIG_BT_CONN_TX=y
# CONFIG_BT_SCA_UPDATE is not set

#
# Bluetooth buffer configuration
#
# end of Bluetooth buffer configuration

#
# Bluetooth Host
#
# end of Bluetooth Host

CONFIG_BT_CTLR_LE_ENC_SUPPORT=y
CONFIG_BT_CTLR_EXT_REJ_IND_SUPPORT=y
CONFIG_BT_CTLR_DATA_LEN_UPDATE_SUPPORT=y
CONFIG_BT_CTLR_PRIVACY_SUPPORT=y
CONFIG_BT_CTLR_EXT_SCAN_FP_SUPPORT=y
CONFIG_BT_CTLR_PHY_UPDATE_SUPPORT=y
CONFIG_BT_CTLR_PHY_2M_SUPPORT=y
CONFIG_BT_CTLR_PHY_CODED_SUPPORT=y
CONFIG_BT_CTLR_ADV_EXT_SUPPORT=y
CONFIG_BT_CTLR_ADV_PERIODIC_SUPPORT=y
CONFIG_BT_CTLR_ADV_PERIODIC_RSP_SUPPORT=y
CONFIG_BT_CTLR_SYNC_PERIODIC_SUPPORT=y
CONFIG_BT_CTLR_SYNC_PERIODIC_RSP_SUPPORT=y
CONFIG_BT_CTLR_SYNC_TRANSFER_SENDER_SUPPORT=y
CONFIG_BT_CTLR_SYNC_TRANSFER_RECEIVER_SUPPORT=y
CONFIG_BT_CTLR_CHAN_SEL_2_SUPPORT=y
CONFIG_BT_CTLR_SCA_UPDATE_SUPPORT=y
CONFIG_BT_CTLR_CONN_RSSI_SUPPORT=y
CONFIG_BT_CTLR_ECDH_SUPPORT=y
# CONFIG_BT_LL_SW_SPLIT is not set

#
# BLE Controller configuration
#
CONFIG_BT_CTLR_CRYPTO=y
CONFIG_BT_CTLR_HCI_VS_BUILD_INFO=""
CONFIG_BT_CTLR_AD_DATA_BACKUP=y
CONFIG_BT_CTLR_DUP_FILTER_LEN=16
CONFIG_BT_CTLR_RX_BUFFERS=6
# CONFIG_BT_CTLR_TX_PWR_PLUS_3 is not set
CONFIG_BT_CTLR_TX_PWR_0=y
# CONFIG_BT_CTLR_TX_PWR_MINUS_4 is not set
# CONFIG_BT_CTLR_TX_PWR_MINUS_8 is not set
# CONFIG_BT_CTLR_TX_PWR_MINUS_12 is not set
# CONFIG_BT_CTLR_TX_PWR_MINUS_16 is not set
# CONFIG_BT_CTLR_TX_PWR_MINUS_20 is not set
# CONFIG_BT_CTLR_TX_PWR_MINUS_40 is not set
CONFIG_BT_CTLR_TX_PWR_ANTENNA=0
# CONFIG_BT_CTLR_TX_PWR_DYNAMIC_CONTROL is not set

#
# BLE Controller features
#
CONFIG_BT_CTLR_LE_ENC=y
CONFIG_BT_CTLR_ECDH=y
CONFIG_BT_CTLR_EXT_REJ_IND=y
CONFIG_BT_CTLR_LE_PING=y
CONFIG_BT_CTLR_DATA_LENGTH=y
CONFIG_BT_CTLR_PHY=y
CONFIG_BT_CTLR_CONN_RSSI=y
CONFIG_BT_CTLR_CHECK_SAME_PEER_CONN=y
CONFIG_BT_CTLR_FILTER_ACCEPT_LIST=y
CONFIG_BT_CTLR_PRIVACY=y
CONFIG_BT_CTLR_RL_SIZE=8
CONFIG_BT_CTLR_EXT_SCAN_FP=y
CONFIG_BT_CTLR_PHY_2M=y
CONFIG_BT_CTLR_PHY_CODED=y
CONFIG_BT_CTLR_CHAN_SEL_2=y
# CONFIG_BT_CTLR_ADV_EXT is not set
# CONFIG_BT_CTLR_SET_HOST_FEATURE is not set
# CONFIG_BT_CTLR_HCI_CODEC_AND_DELAY_INFO is not set
CONFIG_BT_CTLR_DF_CTE_TX_SUPPORT=y
# CONFIG_BT_CTLR_ASSERT_HANDLER is not set
# CONFIG_BT_CTLR_TEST is not set
# CONFIG_BT_SHELL is not set
# CONFIG_BT_EAD is not set
CONFIG_BT_COMPANY_ID=0x05F1

#
# Controller Area Network (CAN) bus subsystem
#
# CONFIG_ISOTP is not set
# end of Controller Area Network (CAN) bus subsystem

# CONFIG_CONSOLE_SUBSYS is not set

#
# System Monitoring Options
#
# CONFIG_THREAD_ANALYZER is not set
# end of System Monitoring Options

#
# Debugging Options
#
# CONFIG_DEBUG is not set
# CONFIG_STACK_USAGE is not set
# CONFIG_STACK_SENTINEL is not set
CONFIG_PRINTK=y
CONFIG_EARLY_CONSOLE=y
# CONFIG_ASSERT is not set
# CONFIG_FORCE_NO_ASSERT is not set
CONFIG_ASSERT_VERBOSE=y
# CONFIG_ASSERT_NO_FILE_INFO is not set
# CONFIG_ASSERT_NO_COND_INFO is not set
# CONFIG_ASSERT_NO_MSG_INFO is not set
# CONFIG_ASSERT_TEST is not set
# CONFIG_OVERRIDE_FRAME_POINTER_DEFAULT is not set
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_THREAD_INFO is not set
# CONFIG_DEBUG_COREDUMP is not set
# end of Debugging Options

# CONFIG_DISK_ACCESS is not set
# CONFIG_DSP is not set
# CONFIG_EMUL is not set
# CONFIG_CHARACTER_FRAMEBUFFER is not set

#
# File Systems
#
# CONFIG_FILE_SYSTEM is not set
# CONFIG_NVS is not set
# end of File Systems

#
# Inter Processor Communication
#
# CONFIG_RPMSG_SERVICE is not set
CONFIG_IPC_SERVICE=y
CONFIG_IPC_SERVICE_REG_BACKEND_PRIORITY=46
CONFIG_IPC_SERVICE_BACKEND_RPMSG=y
CONFIG_IPC_SERVICE_BACKEND_RPMSG_WQ_STACK_SIZE=1024
CONFIG_IPC_SERVICE_BACKEND_RPMSG_NUM_ENDPOINTS_PER_INSTANCE=2
CONFIG_IPC_SERVICE_RPMSG=y
CONFIG_IPC_SERVICE_STATIC_VRINGS=y
CONFIG_IPC_SERVICE_STATIC_VRINGS_ALIGNMENT=4
# CONFIG_IPC_SERVICE_ICMSG is not set
# CONFIG_IPC_SERVICE_ICMSG_ME is not set
# end of Inter Processor Communication

# CONFIG_JWT is not set

#
# Logging
#
# CONFIG_LOG is not set
# CONFIG_LOG_OUTPUT is not set
# end of Logging

#
# Device Management
#

#
# Host command handler subsystem
#
# CONFIG_EC_HOST_CMD is not set
# CONFIG_EC_HOST_CMD_BACKEND_SHI is not set
# end of Host command handler subsystem

# CONFIG_OSDP is not set
# end of Device Management

# CONFIG_MODBUS is not set

#
# Networking
#
CONFIG_NET_BUF=y
# CONFIG_NET_BUF_LOG is not set
# CONFIG_NET_BUF_POOL_USAGE is not set
# end of Networking

#
# Power Management
#
CONFIG_HAS_NO_PM=y
# end of Power Management

#
# Portability
#
# end of Portability

#
# Random Number Generators
#
CONFIG_ENTROPY_DEVICE_RANDOM_GENERATOR=y
# CONFIG_XOROSHIRO_RANDOM_GENERATOR is not set
# CONFIG_XOSHIRO_RANDOM_GENERATOR is not set
CONFIG_CSPRING_ENABLED=y
CONFIG_HARDWARE_DEVICE_CS_GENERATOR=y
# CONFIG_CTR_DRBG_CSPRNG_GENERATOR is not set
# end of Random Number Generators

# CONFIG_RTIO is not set

#
# SD
#
# CONFIG_MMC_STACK is not set
# CONFIG_SDMMC_STACK is not set
# CONFIG_SDIO_STACK is not set
# end of SD

# CONFIG_SETTINGS is not set
# CONFIG_SHELL is not set
# CONFIG_STATS is not set

#
# Storage
#
# CONFIG_STREAM_FLASH is not set
# end of Storage

# CONFIG_TASK_WDT is not set

#
# Testing
#
# CONFIG_ZTEST is not set
# CONFIG_ZTEST_MOCKING is not set
# CONFIG_ZTRESS is not set
# CONFIG_TEST is not set
CONFIG_COVERAGE_GCOV_HEAP_SIZE=16384
# CONFIG_TEST_USERSPACE is not set
# end of Testing

# CONFIG_TIMING_FUNCTIONS is not set
# CONFIG_TRACING is not set
# CONFIG_USB_DEVICE_STACK is not set
# CONFIG_USB_DEVICE_STACK_NEXT is not set
# CONFIG_USB_HOST_STACK is not set
# CONFIG_USBC_STACK is not set
# CONFIG_ZBUS is not set
# end of Subsystems and OS Services

CONFIG_TOOLCHAIN_ZEPHYR_0_16=y
CONFIG_TOOLCHAIN_ZEPHYR_SUPPORTS_THREAD_LOCAL_STORAGE=y

#
# Build and Link Features
#

#
# Linker Options
#
# CONFIG_LINKER_ORPHAN_SECTION_PLACE is not set
CONFIG_LINKER_ORPHAN_SECTION_WARN=y
# CONFIG_LINKER_ORPHAN_SECTION_ERROR is not set
CONFIG_HAS_FLASH_LOAD_OFFSET=y
# CONFIG_USE_DT_CODE_PARTITION is not set
CONFIG_LD_LINKER_SCRIPT_SUPPORTED=y
CONFIG_LD_LINKER_TEMPLATE=y
# CONFIG_CMAKE_LINKER_GENERATOR is not set
# CONFIG_HAVE_CUSTOM_LINKER_SCRIPT is not set
CONFIG_KERNEL_ENTRY="__start"
CONFIG_LINKER_SORT_BY_ALIGNMENT=y
CONFIG_SRAM_OFFSET=0

#
# Linker Sections
#
# CONFIG_LINKER_USE_BOOT_SECTION is not set
# CONFIG_LINKER_USE_PINNED_SECTION is not set
CONFIG_LINKER_GENERIC_SECTIONS_PRESENT_AT_BOOT=y
CONFIG_LINKER_LAST_SECTION_ID=y
CONFIG_LINKER_LAST_SECTION_ID_PATTERN=0xE015E015
CONFIG_LINKER_USE_RELAX=y
# end of Linker Sections
# end of Linker Options

#
# Compiler Options
#
# CONFIG_CODING_GUIDELINE_CHECK is not set
# CONFIG_NATIVE_APPLICATION is not set
CONFIG_COMPILER_FREESTANDING=y
CONFIG_SIZE_OPTIMIZATIONS=y
# CONFIG_SPEED_OPTIMIZATIONS is not set
# CONFIG_DEBUG_OPTIMIZATIONS is not set
# CONFIG_NO_OPTIMIZATIONS is not set
# CONFIG_COMPILER_WARNINGS_AS_ERRORS is not set
# CONFIG_COMPILER_SAVE_TEMPS is not set
CONFIG_COMPILER_COLOR_DIAGNOSTICS=y
CONFIG_FORTIFY_SOURCE_NONE=y
# CONFIG_FORTIFY_SOURCE_COMPILE_TIME is not set
# CONFIG_FORTIFY_SOURCE_RUN_TIME is not set
CONFIG_COMPILER_OPT=""
# CONFIG_MISRA_SANE is not set
# end of Compiler Options

# CONFIG_ASSERT_ON_ERRORS is not set
# CONFIG_NO_RUNTIME_CHECKS is not set
CONFIG_RUNTIME_ERROR_CHECKS=y

#
# Build Options
#
CONFIG_KERNEL_BIN_NAME="zephyr"
CONFIG_OUTPUT_STAT=y
# CONFIG_OUTPUT_SYMBOLS is not set
CONFIG_OUTPUT_DISASSEMBLY=y
# CONFIG_OUTPUT_DISASSEMBLE_ALL is not set
CONFIG_OUTPUT_PRINT_MEMORY_USAGE=y
# CONFIG_CLEANUP_INTERMEDIATE_FILES is not set
# CONFIG_BUILD_NO_GAP_FILL is not set
CONFIG_BUILD_OUTPUT_BIN=y
# CONFIG_BUILD_OUTPUT_EXE is not set
# CONFIG_BUILD_OUTPUT_S19 is not set
# CONFIG_BUILD_OUTPUT_UF2 is not set
# CONFIG_BUILD_OUTPUT_STRIPPED is not set
# CONFIG_APPLICATION_DEFINED_SYSCALL is not set
# CONFIG_MAKEFILE_EXPORTS is not set
# CONFIG_BUILD_OUTPUT_META is not set
CONFIG_BUILD_OUTPUT_STRIP_PATHS=y
# end of Build Options

CONFIG_WARN_DEPRECATED=y
CONFIG_ENFORCE_ZEPHYR_STDINT=y
# end of Build and Link Features

#
# Boot Options
#
# CONFIG_IS_BOOTLOADER is not set
# CONFIG_BOOTLOADER_BOSSA is not set
# end of Boot Options

#
# Compatibility
#
CONFIG_COMPAT_INCLUDES=y
# end of Compatibility

RE: how to enable GPIO+SPI mode on ble application

Susheel Nuguru — Fri, 24 May 2024 09:29:20 GMT

Have you enabled MPSL and FEM also like below?

# Enable MPSL and FEM
CONFIG_MPSL=y
CONFIG_MPSL_FEM=y
CONFIG_MPSL_FEM_NRF21540_GPIO_SPI=y

Can you attach your full compiled .config file here?

RE: how to enable GPIO+SPI mode on ble application

Susheel Nuguru — Wed, 22 May 2024 16:14:44 GMT

Hi,

Sorry for delays, I was unable to look into this today and will try my best to give you a response tomorrow. Thanks for your patience so far.