No SOURCES given to Zephyr library

RE: No SOURCES given to Zephyr library

Hung Bui — Tue, 10 Sep 2024 08:15:08 GMT

Hi Alex,

Have you verified that there is no problem with the hardware ?

Have you tried to toggle the uart2 pins as GPIO pins ? Just do a quick test if you can change the level of the pins.

If it work, please try to test with a simple UART sample and use a logic analyzer to check if you have correct UART output on the pins.
After that you can start to try testing with the serial lte modem sample.

RE: No SOURCES given to Zephyr library

ALEJANDRO_CEIT — Mon, 09 Sep 2024 15:48:44 GMT

Hi Hung,

thanks for your response. Here si the full schematic:

devzone.nordicsemi.com/.../DFR8RAILOG_5F00_WNODE_5F00_v0.pdf

The solution that Charlie provided working with the nrf9160DK but not with my Custom board. I'm trying to communicate the nrf9160 SIP with STM32 MCU via uart2 but is not working and I think there something that I'm missing..

Here are my custom board files:

devzone.nordicsemi.com/.../2273.nrf9160_5F00_sica_5F00_b1.zip

devzone.nordicsemi.com/.../0844.custom_5F00_board_5F00_nrf9160_5F00_ns.conf

devzone.nordicsemi.com/.../6283.custom_5F00_board_5F00_nrf9160_5F00_ns.overlay

I need to do a field test using nrf9160 LTE communications next week, so I appreciate any help.

Regards,

Alex

RE: No SOURCES given to Zephyr library

Hung Bui — Mon, 09 Sep 2024 12:00:31 GMT

Hi Alex,
Charlie is out of office for a few days. I will take over in the mean time.
Could you please upload a higher resolution of the schematic ? Preferably as pdf file instead of png.

Please give more info about the code Charlie provided. Besides the warnings do you have any issue , does it work as it should ?

RE: No SOURCES given to Zephyr library

ALEJANDRO_CEIT — Wed, 04 Sep 2024 15:30:54 GMT

Hi Charlie,

I followed your steps and I'm able to compile but I got some weird warnings that I don't understand, here is the compiling log:

devzone.nordicsemi.com/.../custom_5F00_log_5F00_3.zip

Other problem is when I flashed my custom board I can't communicate my stm32 micro with the nrf9160 module via uart.. but when I flashed my nrf9160DK with this build I can communicate using terminal through FTDI wire put in the same uart pins..

Here is the schematic of my custom board:

devzone.nordicsemi.com/.../schematic_5F00_custom_5F00_board.zip

is something wrong in the design?

thanks for your help!

Regards, Alex

RE: No SOURCES given to Zephyr library

Charlie — Tue, 03 Sep 2024 09:17:21 GMT

Hi Alex,

I did copy and rename to your files in the following way.

nrf9160dk_nrf9160->custom_board_nrf9160

NRF9160DK_NRF9160->CUSTOM_BOARD_NRF9160

I got the following custom board configuration.

devzone.nordicsemi.com/.../5488.custom_5F00_board_5F00_nrf9160.zip

In the SLM board folder, do same and get the following files.

devzone.nordicsemi.com/.../custom_5F00_board_5F00_nrf9160_5F00_ns.overlay

devzone.nordicsemi.com/.../custom_5F00_board_5F00_nrf9160_5F00_ns.conf

I have no problem to build the project.

Building ncs261_serial_lte_modem
west build --build-dir /opt/nordic/ncs/myapps/ncs261_serial_lte_modem/build /opt/nordic/ncs/myapps/ncs261_serial_lte_modem --pristine --board custom_board_nrf9160_ns -- -DNCS_TOOLCHAIN_VERSION=NONE -DBOARD_ROOT=/opt/nordic/ncs/myapps;/opt/nordic/ncs/myapps/ncs261_serial_lte_modem

-- west build: generating a build system
Loading Zephyr default modules (Zephyr base).
-- Application: /opt/nordic/ncs/myapps/ncs261_serial_lte_modem
-- CMake version: 3.21.0
-- Found Python3: /opt/nordic/ncs/toolchains/580e4ef81c/opt/python@3.9/bin/python3.9 (found suitable version "3.9.6", minimum required is "3.8") found components: Interpreter 
-- Cache files will be written to: /Users/cs/Library/Caches/zephyr
-- Zephyr version: 3.5.99 (/opt/nordic/ncs/v2.6.1/zephyr)
-- Found west (found suitable version "1.2.0", minimum required is "0.14.0")
-- Board: custom_board_nrf9160_ns, Revision: 0.14.0
-- Found host-tools: zephyr 0.16.5 (/opt/nordic/ncs/toolchains/580e4ef81c/opt/zephyr-sdk)
-- Found toolchain: zephyr 0.16.5 (/opt/nordic/ncs/toolchains/580e4ef81c/opt/zephyr-sdk)
-- Found Dtc: /opt/nordic/ncs/toolchains/580e4ef81c/bin/dtc (found suitable version "1.6.1", minimum required is "1.4.6") 
-- Found BOARD.dts: /opt/nordic/ncs/myapps/boards/arm/custom_board_nrf9160/custom_board_nrf9160_ns.dts
-- Found devicetree overlay: /opt/nordic/ncs/myapps/boards/arm/custom_board_nrf9160/custom_board_nrf9160_ns_0_14_0.overlay
-- Found devicetree overlay: /opt/nordic/ncs/myapps/ncs261_serial_lte_modem/boards/custom_board_nrf9160_ns.overlay
-- Generated zephyr.dts: /opt/nordic/ncs/myapps/ncs261_serial_lte_modem/build/zephyr/zephyr.dts
-- Generated devicetree_generated.h: /opt/nordic/ncs/myapps/ncs261_serial_lte_modem/build/zephyr/include/generated/devicetree_generated.h
-- Including generated dts.cmake file: /opt/nordic/ncs/myapps/ncs261_serial_lte_modem/build/zephyr/dts.cmake

warning: Experimental symbol TFTP_LIB is enabled.


warning: Experimental symbol HTTP_CLIENT is enabled.

Parsing /opt/nordic/ncs/myapps/ncs261_serial_lte_modem/Kconfig
Loaded configuration '/opt/nordic/ncs/myapps/boards/arm/custom_board_nrf9160/custom_board_nrf9160_ns_defconfig'
Merged configuration '/opt/nordic/ncs/myapps/ncs261_serial_lte_modem/prj.conf'
Merged configuration '/opt/nordic/ncs/myapps/ncs261_serial_lte_modem/boards/custom_board_nrf9160_ns.conf'
Configuration saved to '/opt/nordic/ncs/myapps/ncs261_serial_lte_modem/build/zephyr/.config'
Kconfig header saved to '/opt/nordic/ncs/myapps/ncs261_serial_lte_modem/build/zephyr/include/generated/autoconf.h'
-- Found GnuLd: /opt/nordic/ncs/toolchains/580e4ef81c/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm-zephyr-eabi/12.2.0/../../../../arm-zephyr-eabi/bin/ld.bfd (found version "2.38") 
-- The C compiler identification is GNU 12.2.0
-- The CXX compiler identification is GNU 12.2.0
-- The ASM compiler identification is GNU
-- Found assembler: /opt/nordic/ncs/toolchains/580e4ef81c/opt/zephyr-sdk/arm-zephyr-eabi/bin/arm-zephyr-eabi-gcc
-- Found Python3: /opt/nordic/ncs/toolchains/580e4ef81c/opt/python@3.9/bin/python3.9 (found version "3.9.6") found components: Interpreter 
Changed board to secure custom_board_nrf9160 (NOT NS)

=== child image mcuboot -  begin ===
loading initial cache file /opt/nordic/ncs/myapps/ncs261_serial_lte_modem/build/mcuboot/child_image_preload.cmake
Loading Zephyr default modules (Zephyr base).
-- Application: /opt/nordic/ncs/v2.6.1/bootloader/mcuboot/boot/zephyr
-- CMake version: 3.21.0
-- Found Python3: /opt/nordic/ncs/toolchains/580e4ef81c/opt/python@3.9/bin/python3.9 (found suitable version "3.9.6", minimum required is "3.8") found components: Interpreter 
-- Cache files will be written to: /Users/cs/Library/Caches/zephyr
-- Zephyr version: 3.5.99 (/opt/nordic/ncs/v2.6.1/zephyr)
-- Found west (found suitable version "1.2.0", minimum required is "0.14.0")
-- Board: custom_board_nrf9160, Revision: 0.14.0
-- Found host-tools: zephyr 0.16.5 (/opt/nordic/ncs/toolchains/580e4ef81c/opt/zephyr-sdk)
-- Found toolchain: zephyr 0.16.5 (/opt/nordic/ncs/toolchains/580e4ef81c/opt/zephyr-sdk)
-- Found Dtc: /opt/nordic/ncs/toolchains/580e4ef81c/bin/dtc (found suitable version "1.6.1", minimum required is "1.4.6") 
-- Found BOARD.dts: /opt/nordic/ncs/myapps/boards/arm/custom_board_nrf9160/custom_board_nrf9160.dts
-- Found devicetree overlay: /opt/nordic/ncs/myapps/boards/arm/custom_board_nrf9160/custom_board_nrf9160_0_14_0.overlay
-- Found devicetree overlay: /opt/nordic/ncs/v2.6.1/bootloader/mcuboot/boot/zephyr/app.overlay
-- Generated zephyr.dts: /opt/nordic/ncs/myapps/ncs261_serial_lte_modem/build/mcuboot/zephyr/zephyr.dts
-- Generated devicetree_generated.h: /opt/nordic/ncs/myapps/ncs261_serial_lte_modem/build/mcuboot/zephyr/include/generated/devicetree_generated.h
-- Including generated dts.cmake file: /opt/nordic/ncs/myapps/ncs261_serial_lte_modem/build/mcuboot/zephyr/dts.cmake
Parsing /opt/nordic/ncs/v2.6.1/bootloader/mcuboot/boot/zephyr/Kconfig
Loaded configuration '/opt/nordic/ncs/myapps/boards/arm/custom_board_nrf9160/custom_board_nrf9160_defconfig'
Merged configuration '/opt/nordic/ncs/v2.6.1/bootloader/mcuboot/boot/zephyr/prj.conf'
Merged configuration '/opt/nordic/ncs/v2.6.1/nrf/modules/mcuboot/tfm.conf'
Merged configuration '/opt/nordic/ncs/v2.6.1/nrf/modules/mcuboot/fih_low_enable.conf'
Merged configuration '/opt/nordic/ncs/v2.6.1/nrf/subsys/partition_manager/partition_manager_enabled.conf'
Merged configuration '/opt/nordic/ncs/myapps/ncs261_serial_lte_modem/child_image/mcuboot.conf'
Merged configuration '/opt/nordic/ncs/myapps/ncs261_serial_lte_modem/build/mcuboot/zephyr/misc/generated/extra_kconfig_options.conf'
Configuration saved to '/opt/nordic/ncs/myapps/ncs261_serial_lte_modem/build/mcuboot/zephyr/.config'
Kconfig header saved to '/opt/nordic/ncs/myapps/ncs261_serial_lte_modem/build/mcuboot/zephyr/include/generated/autoconf.h'
-- Found GnuLd: /opt/nordic/ncs/toolchains/580e4ef81c/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm-zephyr-eabi/12.2.0/../../../../arm-zephyr-eabi/bin/ld.bfd (found version "2.38") 
-- The C compiler identification is GNU 12.2.0
-- The CXX compiler identification is GNU 12.2.0
-- The ASM compiler identification is GNU
-- Found assembler: /opt/nordic/ncs/toolchains/580e4ef81c/opt/zephyr-sdk/arm-zephyr-eabi/bin/arm-zephyr-eabi-gcc
-- Using ccache: /opt/nordic/ncs/toolchains/580e4ef81c/bin/ccache
CMake Warning at /opt/nordic/ncs/v2.6.1/zephyr/CMakeLists.txt:862 (message):
  No SOURCES given to Zephyr library: drivers__console

  Excluding target from build.


MCUBoot bootloader key file: /opt/nordic/ncs/v2.6.1/bootloader/mcuboot/root-ec-p256.pem
-- Configuring done
-- Generating done
-- Build files have been written to: /opt/nordic/ncs/myapps/ncs261_serial_lte_modem/build/mcuboot
=== child image mcuboot -  end ===

CMake Warning at /opt/nordic/ncs/v2.6.1/nrf/modules/mcuboot/CMakeLists.txt:382 (message):
  

          ---------------------------------------------------------
          --- WARNING: Using default MCUBoot key, it should not ---
          --- be used for production.                           ---
          ---------------------------------------------------------
          



-- Using ccache: /opt/nordic/ncs/toolchains/580e4ef81c/bin/ccache
CMake Warning at /opt/nordic/ncs/v2.6.1/nrf/cmake/partition_manager.cmake:79 (message):
  

          ---------------------------------------------------------------------
          --- WARNING: Using a bootloader without pm_static.yml.            ---
          --- There are cases where a deployed product can consist of       ---
          --- multiple images, and only a subset of these images can be     ---
          --- upgraded through a firmware update mechanism. In such cases,  ---
          --- the upgradable images must have partitions that are static    ---
          --- and are matching the partition map used by the bootloader     ---
          --- programmed onto the device.                                   ---
          ---------------------------------------------------------------------
          

Call Stack (most recent call first):
  /opt/nordic/ncs/v2.6.1/zephyr/cmake/modules/kernel.cmake:248 (include)
  /opt/nordic/ncs/v2.6.1/zephyr/cmake/modules/zephyr_default.cmake:138 (include)
  /opt/nordic/ncs/v2.6.1/zephyr/share/zephyr-package/cmake/ZephyrConfig.cmake:66 (include)
  /opt/nordic/ncs/v2.6.1/zephyr/share/zephyr-package/cmake/ZephyrConfig.cmake:92 (include_boilerplate)
  CMakeLists.txt:9 (find_package)


Dropping partition 'nrf_modem_lib_trace' since its size is 0.
-- Configuring done
-- Generating done
-- Build files have been written to: /opt/nordic/ncs/myapps/ncs261_serial_lte_modem/build
-- west build: building application
[1/400] Preparing syscall dependency handling

[1/180] Preparing syscall dependency handling

[4/180] Generating include/generated/version.h
-- Zephyr version: 3.5.99 (/opt/nordic/ncs/v2.6.1/zephyr), build: v3.5.99-ncs1-1
[180/180] Linking C executable zephyr/zephyr.elf
Memory region         Used Size  Region Size  %age Used
           FLASH:       30924 B        48 KB     62.92%
             RAM:       16336 B        32 KB     49.85%
        IDT_LIST:          0 GB        32 KB      0.00%
[9/400] Generating include/generated/version.h
-- Zephyr version: 3.5.99 (/opt/nordic/ncs/v2.6.1/zephyr), build: v3.5.99-ncs1-1
[14/400] Generating ../../tfm/CMakeCache.txt
CMake Warning at cmake/version.cmake:22 (message):
  Actual TF-M version is not available from Git repository.  Settled to
  v2.0.0
Call Stack (most recent call first):
  CMakeLists.txt:22 (include)


-- Found Git: /opt/nordic/ncs/toolchains/580e4ef81c/bin/git (found version "2.37.3") 
-- The C compiler identification is GNU 12.2.0
-- The CXX compiler identification is GNU 12.2.0
-- The ASM compiler identification is GNU
-- Found assembler: /opt/nordic/ncs/toolchains/580e4ef81c/opt/zephyr-sdk/arm-zephyr-eabi/bin/arm-zephyr-eabi-gcc
-- Found Python3: /opt/nordic/ncs/toolchains/580e4ef81c/opt/python@3.9/bin/python3.9 (found version "3.9.6") found components: Interpreter 
CMake Deprecation Warning at /opt/nordic/ncs/v2.6.1/zephyr/cmake/modules/FindDeprecated.cmake:121 (message):
  'PYTHON_PREFER' variable is deprecated.  Please use Python3_EXECUTABLE
  instead.
Call Stack (most recent call first):
  /opt/nordic/ncs/v2.6.1/zephyr/cmake/modules/python.cmake:16 (find_package)
  /opt/nordic/ncs/v2.6.1/zephyr/cmake/modules/user_cache.cmake:30 (include)
  /opt/nordic/ncs/v2.6.1/zephyr/cmake/modules/extensions.cmake:5 (include)
  /opt/nordic/ncs/v2.6.1/nrf/subsys/nrf_security/tfm/CMakeLists.txt:38 (include)


-- Found Python3: /opt/nordic/ncs/toolchains/580e4ef81c/opt/python@3.9/bin/python3.9 (found suitable version "3.9.6", minimum required is "3.8") found components: Interpreter 
-- Cache files will be written to: /Users/cs/Library/Caches/zephyr
-- Configuring done
-- Generating done
CMake Warning:
  Manually-specified variables were not used by the project:

    CRYPTO_RNG_MODULE_ENABLED
    MBEDTLS_PSA_CRYPTO_USER_CONFIG_FILE
    PYTHON_PREFER


-- Build files have been written to: /opt/nordic/ncs/myapps/ncs261_serial_lte_modem/build/tfm
[168/172] Linking C executable bin/tfm_s.axf
Memory region         Used Size  Region Size  %age Used
           FLASH:       31592 B      32256 B     97.94%
             RAM:       14392 B        32 KB     43.92%
[25/400] Performing install step for 'tfm'
-- Install configuration: "MinSizeRel"
----- Installing platform NS -----
[391/400] Linking C executable zephyr/zephyr.elf
Memory region         Used Size  Region Size  %age Used
           FLASH:      228916 B       416 KB     53.74%
             RAM:      101288 B     211608 B     47.87%
        IDT_LIST:          0 GB        32 KB      0.00%
[395/400] Generating ../../zephyr/app_update.bin
image.py: sign the payload
[397/400] Generating ../../zephyr/app_signed.hex
image.py: sign the payload
[398/400] Generating ../../zephyr/app_test_update.hex
image.py: sign the payload
[400/400] Generating zephyr/merged.hex
 *  Terminal will be reused by tasks, press any key to close it.

Best regards,

Charlie

RE: No SOURCES given to Zephyr library

ALEJANDRO_CEIT — Mon, 02 Sep 2024 15:38:15 GMT

Hi Charlie,

thanks for your time!

I did what you mentioned but I got errors during the compiling process. I'm totally lost trying to make my board work.

This is the compiling log:

devzone.nordicsemi.com/.../custom_5F00_log_5F00_2.zip

and this is the new custom board folder:

devzone.nordicsemi.com/.../custom_5F00_board_5F00_nrf9160.zip

I copied all the files from C:\ncs\v2.6.1\zephyr\boards\arm\nrf9160dk_nrf9160 in a new folder and modified the files according to my design.. but still failing.

thanks in advance, I appreciate your help.

Regards, Alex

RE: No SOURCES given to Zephyr library

Charlie — Mon, 02 Sep 2024 11:07:19 GMT

Hi Alex,

I did a quick compare between your board file and nrf9160dk_nrf9160. There are quite mange changes and not just a simple copy.

The warning and errors are reported by building progress comes from different parts of the change.

I would suggest you put the two board folders in to a custom board folder and modify nrf9160dk_nrf9160 part by part following changes you have made with nrf9160_sica_b1 and verify with SLM building process.

The VS codes comparison function may help a lot on this process. Just let me know if you still have issues.

Best regards,

Charlie