Sid_end_device cannot use rtt

RE: Sid_end_device cannot use rtt

dejans — Tue, 24 Sep 2024 14:38:49 GMT

Hi,

You could try to reset your device using nrfjprog options which reset the board. For example, you could try to reset your device using nrfjprog --hardreset, nrfjprog --reset or nrfjprog --debugreset.

Best regards,
Dejan

RE: Sid_end_device cannot use rtt

666 — Tue, 24 Sep 2024 10:03:21 GMT

nrf52840+Semtech SX1262

RE: Sid_end_device cannot use rtt

dejans — Tue, 24 Sep 2024 09:36:05 GMT

Hi,

Can you provide more information about your custom board?

Best regards,
Dejan

RE: Sid_end_device cannot use rtt

666 — Tue, 24 Sep 2024 01:06:26 GMT

Already completed;

Using the default overlay-hello

After testing, if using nrf52840dk, it will also work like this, but pressing the reset button again will make it normal

But if a customized board is used, what can be used instead of this reset button

RE: Sid_end_device cannot use rtt

dejans — Mon, 23 Sep 2024 14:26:19 GMT

Hi,

Runar is currently out of the office.

Have you done everything mentioned in setting up your Sidewalk device?

Which sample_variant do you use?

Best regards,
Dejan

RE: Sid_end_device cannot use rtt

666 — Mon, 23 Sep 2024 07:44:10 GMT

I added it through

&qspi {

status = "disabled";

};

and

CONFIG_MAIN_STACK_SIZE=2048

Solved the above errors

But new problems have arisen,

This is done through debugging in sid_init (&sm ->sid ->config,&sm ->sid ->handle); After calling, it died without any modifications to the code section, using the default code of the demo

Looking forward to your reply

RE: Sid_end_device cannot use rtt

666 — Mon, 23 Sep 2024 04:26:43 GMT

There is good news, I have found the reason. It is because there is no external flash that RTT cannot print. I removed the configuration related to external flash and was able to log normally. However, there was another error message

Looking forward to your reply

RE: Sid_end_device cannot use rtt

666 — Sat, 21 Sep 2024 07:43:57 GMT

Thank you for your analysis. After testing for the past two days, I found that I did not burn “nrfjprog -- sectorerase -- program nordic_aws_nrf52840.hex -- reset”. Then, according to your RTT configuration, rtt can run normally. However, this error occurred: "<err>qspi_nor: JEDEC id [ff ff ff] expect [c2 28 17]".

So, I went to add it

&qspi {

status = "disabled";

};

Then compile it and flash “nrfjprog -- sectorerase -- program nordic_aws_nrf52840.hex -- reset”, but the result is that rtt cannot be printed. Then I removed the one I just added, but the result is that rff still cannot be printed.

Later on, I felt that RTT was most likely able to print the logs of other demos (because I saw the peripheral_uart), but I still don't know why.

1.So even though I added the step 'nrfjprog -- sectorerase -- program nordic_aws_nrf52840. hex -- reset', rtt still doesn't work~~.

2.Except for not trying DK, I have tried everything you said but have had no results.

3.a custom board, We made this ourselves, which is composed of nrf52840+Semtech SX1262 (only these two chips, no others,no external flash). I don't know the difference between burning with this board and nrf52840dk.

Looking forward to your reply

RE: Sid_end_device cannot use rtt

runsiv — Thu, 19 Sep 2024 11:17:59 GMT

Thank you, and you flash this custom board with a dk or a jlink? Try to flash your application to the custom board, and connect the RTT backend after the application has started,

Regards

Runar

RE: Sid_end_device cannot use rtt

666 — Thu, 19 Sep 2024 09:13:18 GMT

a custom board

RE: Sid_end_device cannot use rtt

runsiv — Thu, 19 Sep 2024 08:57:19 GMT

Sorry, let me try again

Are you using the DK or a custom board?

Regards

Runar

RE: Sid_end_device cannot use rtt

666 — Thu, 19 Sep 2024 08:15:42 GMT

I have tried the changes you made above, but it still doesn't work. For jlink, I can print it normally using the peripher_uart ble demo. I don't quite understand the sentence ' You are not using the DK but trying to flash another board using the nRF52840'

RE: Sid_end_device cannot use rtt

runsiv — Thu, 19 Sep 2024 07:54:23 GMT

Just to be sure. You are not using the DK but trying to flash another board using the nRF52840? If not did you use a jlink with support for RTT?

I tested the sid_end_device sample with the 52840dk and the following changes to the prj.conf

# Log
CONFIG_LOG=y
#CONFIG_LOG_PRINTK=y
CONFIG_LOG_BUFFER_SIZE=2048
CONFIG_NVS_LOG_LEVEL_WRN=y
CONFIG_USE_SEGGER_RTT=y
CONFIG_LOG_BACKEND_RTT=y
CONFIG_LOG_BACKEND_UART=n

And it printed the log for RTT just fine.

Regards

Runar

RE: Sid_end_device cannot use rtt

666 — Wed, 18 Sep 2024 01:19:36 GMT

For the default demo, only two changes were made. The first one, prj.conf as mentioned in the question, and the second one, as shown in the above figure, only moved the board target, selecting nrf52840d_nrf52840 and selecting Nordic Soc, without moving anything else

RE: Sid_end_device cannot use rtt

runsiv — Mon, 16 Sep 2024 11:20:56 GMT

1. As sid_end_device has a lot of configuration options depending on the config you select, could you elaborate which config you have selected?

2. I would presume it uses uart as default since you already would be using uart for the command line interface. Normally uart0 is the default uart and you can see the default pins here and here

Regards

Runar