[nRF52820] USB Power Configuration

RE: [nRF52820] USB Power Configuration

JONATHAN LL — Tue, 19 Aug 2025 09:11:14 GMT

Sorry for the late reply here:

[quote user="sunghoryu"](1) So Figure 2 shows VDDH being connected to VDD instead of VBUS. Would this be the Normal Voltage mode? [/quote]

Yes, this is normal voltage mode.

[quote user="sunghoryu"]Assuming VBUS is connected to +5V of the USB, would VDD_nRF be externally supplied i.e. +3V3 buck converter? Would this be a safe mode of operation for the nRF52820?[/quote]

You can choose to either supply the nRF from normal voltage mode or High voltage mode, both options also support the use of USB but the implementation can be a bit different.

If you intend to only power the device from USB as it seems that you are doing then the simplest solution to implement is to configure the device for High voltage mode and use the USB as a source.

So Config 1 https://docs.nordicsemi.com/bundle/ps_nrf52820/page/ref_circuitry.html#ariaid-title2

You can read more about the power supply options here:
https://docs.nordicsemi.com/bundle/ps_nrf52820/page/power.html#ariaid-title5
https://docs.nordicsemi.com/bundle/ps_nrf52820/page/power.html#ariaid-title8

[quote user="sunghoryu"](3) When using USB as the main voltage source, is there an advantage/disadvantage to using High Voltage mode over Normal Voltage mode?[/quote]

The main difference here will be how many components you will need to implement in the design, the device will operate similarly so no major difference in performance.

[quote user="sunghoryu"](4) I would like to request a quick schematic review for the nRF52820, just to make sure all the wiring and power sequence is correct. Would you be able to share an email of point-of-contact?[/quote]

You can create a private ticket here on Devzone, it is private and will only be viewed by a nordic engineer and everything will be confidential between you and nordic.

[quote user="sunghoryu"]Would a configuration like below be acceptable to power the nRF52820 and also use the USB connection (assuming D+/- connection)?[/quote]

Yes you can also set up the device to be powered in this way, normal voltage mode and then power the VBUS separately for USB use case, but you will need extra converter to step down the voltage for normal voltage mode config.

Regards,
Jonathan

RE: [nRF52820] USB Power Configuration

sunghoryu — Thu, 14 Aug 2025 19:21:50 GMT

Hello Jonathan,

Would there be an update on this request?

Thank you!

RE: [nRF52820] USB Power Configuration

sunghoryu — Wed, 13 Aug 2025 20:58:55 GMT

Would a configuration like below be acceptable to power the nRF52820 and also use the USB connection (assuming D+/- connection)?

RE: [nRF52820] USB Power Configuration

sunghoryu — Wed, 13 Aug 2025 17:38:33 GMT

Hello Jonathan,

Thank you for the prompt response! Some follow-up questions:

(1) So Figure 2 shows VDDH being connected to VDD instead of VBUS. Would this be the Normal Voltage mode? Assuming VBUS is connected to +5V of the USB, would VDD_nRF be externally supplied i.e. +3V3 buck converter? Would this be a safe mode of operation for the nRF52820?

(2) I was under the impression that USB operation and Normal Voltage mode are mutually exclusive. That would not be the case?

(3) When using USB as the main voltage source, is there an advantage/disadvantage to using High Voltage mode over Normal Voltage mode?

(4) I would like to request a quick schematic review for the nRF52820, just to make sure all the wiring and power sequence is correct. Would you be able to share an email of point-of-contact?

Thank you!

RE: [nRF52820] USB Power Configuration

JONATHAN LL — Wed, 13 Aug 2025 13:37:40 GMT

[quote user=""]'m referring to Figure 153 of the datasheet, which shows Circuit Configuration #1 and is the only reference design available showing a USB-powered connection:[/quote]

You can add DCDC components if you want, so we dont show all possible combinations, but for the USB section this is correct.

[quote user=""]From the notes above in Section 7.3 Reference Circuitry, it seems that when supplying power through USB, VBUS and VDDH must be connected:[/quote]

Correct, VDDH needs to be used here. The alterative here is to have a external regulator that steps down the voltage that you could then use to supply the device in normal voltage mode. So something like the figure 2 https://docs.nordicsemi.com/bundle/ps_nrf52820/page/ref_circuitry.html#ariaid-title3 is also an option.

[quote user=""](1) When powering the nRF52820 using USB, it is only possible to use High Voltage mode (Normal Voltage mode is not possible), correct? As shown in Section 5.3.1 Main Supply?[/quote]

It is not possible to power the nRF52 in normal voltage mode directly from the USB as the voltage is to high. https://docs.nordicsemi.com/bundle/ps_nrf52820/page/abs_max_ratings.html

[quote user=""](3) Similarly, when using an external J-Link to flash the nRF52820, the power pin of the J-Link would connect to the internally generated VDD rail?[/quote]

Correct.

[quote user=""](4) Would a configuration like this be possible where VDD and VDDH are connected and supplied externally, while only VBUS is connected to +5V? If not, why not? FYI, the diagram below uses nRF52840 but the idea would be the same for nRF52820[/quote]

You can use an external regulator to step down the voltage so that the nRF can work in normal voltage mode.

Regards,
Jonathan