RE: Not able to access debug port via jlink

Syed Maysum Abbas Zaidi — Wed, 10 Dec 2025 09:29:50 GMT

Hi, I checked your log file and it shows J-Link debugger itself is detected and configured correctly But when it tries to access the nRF53 debug port, all debug port register writes fail with -1, and JLINK_IsConnected() reports that the probe is not connected to a valid target. This indicates that the PC to J Link path is fine, but the J-Link cannot communicate with the nRF53’s debug port at all.

That is mostly caused by a hardware connection or power issue on the target side. Could you please check the following:

For reliable SWD debugging with J Link, you should power the custom board so that VDD is around 3.0–3.3 V, and connect that same VDD to the debugger’s VTref pin.
Verify SWD wiring (SWDIO, SWDCLK, GND, VTref), connector orientation and no series resistors or level shifters should be on SWD lines.

Kind Regards,
Syed Maysum

RE: Not able to access debug port via jlink

Nagari Gopal — Tue, 09 Dec 2025 14:06:21 GMT

Hii, using custom board of nrf53 series. Programming debug is showing, but not able to access or write the firmware.

If i try using the nrf connect programmer, its showing like this

2025-12-09T14:03:46.872Z INFO Selected device with the serial number 000601001636
2025-12-09T14:03:46.872Z INFO Using nrfutil device to communicate with target via JLink
2025-12-09T14:03:46.896Z DEBUG Sending event "programmer: device selected"
2025-12-09T14:03:46.896Z DEBUG Sending event "programmer: running nrfutil device"
2025-12-09T14:03:47.051Z DEBUG Sending event "programmer: running nrfutil device"
2025-12-09T14:03:47.175Z INFO Reading readback protection status for Application core
2025-12-09T14:03:47.176Z INFO Reading readback protection status for Application core 0%
2025-12-09T14:03:47.345Z INFO Reading readback protection status for Application core 50%
2025-12-09T14:03:47.345Z INFO Reading readback protection status for Application core 50%
2025-12-09T14:03:47.458Z ERROR Failed "reading readback protection status for application core". Error: code: 1, description: Generic, message: Batch task protection-get failed, Device error: Setting the debug port SELECT register failed while powering up sys and debug regions (Unknown Error in J-Link DLL (error code =-1)).

This might indicate that the debug port is unavailable. Please double-check device power supply and SWD lines, and that SWD isn't disabled
2025-12-09T14:03:47.487Z ERROR Error: Failed with exit code 1.
One or more batch tasks failed:
* 601001636: Device error: Setting the debug port SELECT register failed while powering up sys and debug regions (Unknown Error in J-Link DLL (error code =-1)).

This might indicate that the debug port is unavailable. Please double-check device power supply and SWD lines, and that SWD isn't disabled (Generic)

Message: Batch task protection-get failed, Device error: Setting the debug port SELECT register failed while powering up sys and debug regions (Unknown Error in J-Link DLL (error code =-1)).

This might indicate that the debug port is unavailable. Please double-check device power supply and SWD lines, and that SWD isn't disabled.
2025-12-09T14:03:47.487Z ERROR Error: Failed with exit code 1.
One or more batch tasks failed:
* 601001636: Device error: Setting the debug port SELECT register failed while powering up sys and debug regions (Unknown Error in J-Link DLL (error code =-1)).

This might indicate that the debug port is unavailable. Please double-check device power supply and SWD lines, and that SWD isn't disabled (Generic)

Message: Batch task protection-get failed, Device error: Setting the debug port SELECT register failed while powering up sys and debug regions (Unknown Error in J-Link DLL (error code =-1)).

This might indicate that the debug port is unavailable. Please double-check device power supply and SWD lines, and that SWD isn't disabled.