Baseline Power Consumption Benchmarking on nrf52dk

RE: Baseline Power Consumption Benchmarking on nrf52dk

Vidar Berg — Thu, 19 Feb 2026 13:33:38 GMT

Do you see the same floor current if you increase the supply voltage from 2.9 to 3v in the PPK SW? I measured the VDD to be 2.9V on my nRF52 DK when I did the measurements earlier so that is how I ended up with that value. It would also be interesting to know if you get the same result if you use the ampere mode instead (see DK and PPK user guide for how to hook up the board for this)

[quote user="federicoc"]If it is OFF the mcu is not running.[/quote]

As far as I remember, VDD_nrf will be supplied so the nRF52832 should be running, but not the interface MCU and the other circuits that are on a separate power domain.

RE: Baseline Power Consumption Benchmarking on nrf52dk

federicoc — Wed, 18 Feb 2026 16:00:47 GMT

Thank you so much Vidar, I turned off the board before taking the picture. Not sure what you mean by measuring current leakage if the power switch is OFF. If it is OFF the mcu is not running.
You are correct about the ground but it did not affect much the measurement.

Here is the setup and the current measurement

RE: Baseline Power Consumption Benchmarking on nrf52dk

Vidar Berg — Wed, 18 Feb 2026 07:42:07 GMT

The ground wire is connected to the '+' pin instead of the '-', which is wrong. The Power switch is also in the OFF position. This needs to be on when measuring to avoid current leakage.

RE: Baseline Power Consumption Benchmarking on nrf52dk

federicoc — Tue, 17 Feb 2026 16:50:53 GMT

I was hoping to provide some progresses as I had ordered two more nrf52dk from digikey.
Unfortunately, I tested one and i got the same 200uA result.
Could it be the ppk?

RE: Baseline Power Consumption Benchmarking on nrf52dk

Vidar Berg — Tue, 17 Feb 2026 09:19:48 GMT

Thanks for confirming. This suggests that something is wrong with the setup. Hopefully, you will get the expected results when you try it on a different DK.

RE: Baseline Power Consumption Benchmarking on nrf52dk

federicoc — Mon, 16 Feb 2026 18:05:30 GMT

Vidar, thank you for your reply.
Indeed I get a higher current when the Led is on.
Here is the trace with the pre-compiled hex:
The shape is the same but the floor current is of around 194uA. Similar to what it was identified in the other blog as well.
I am gonna try with a different dk and post the results here

RE: Baseline Power Consumption Benchmarking on nrf52dk

Vidar Berg — Mon, 16 Feb 2026 06:39:50 GMT

If you try the "Hello World" sample it is sufficient to add CONFIG_SERIAL=n the project configuration (this is true for most samples). You can also try the pre-compiled hex I posted here /f/nordic-q-a/120743/ble-advertising-power-benchmark/532498.

[quote user="federicoc"]prj.conf and overlay file and a code that only flashes an led on and off on the nrf52dk (pin 20), i read a current of 160uA when led is off.[/quote]

Do you measure more when it is on? The measurements should not be affected by the led states as they are supplied by USB bus.

RE: Baseline Power Consumption Benchmarking on nrf52dk

federicoc — Mon, 16 Feb 2026 01:50:53 GMT

Ok, so the configuration of board, ppk and wiring seems correct.
I still struggle to understand how with everything disabled in
prj.conf and overlay file and a code that only flashes an led on and off on the nrf52dk (pin 20), i read a current of 160uA when led is off.
Is there a sample that has everything turned off and power mode configured for the lowest possible consumption that I can use for reference?

Thank you

CONFIG_CPP=y
CONFIG_GPIO=y
CONFIG_SERIAL=n
CONFIG_PM_DEVICE=y
&uart0 {
 status = "disabled";
};


&pwm0 {
 status = "disabled";
};

&bprot {
 status = "disabled";
};

&ccm {
 status = "disabled";
};

&ecb {
 status = "disabled";
};

&ficr {
 status = "disabled";
};

&gpiote {
 status = "okay";
};

&egu0 {
 status = "disabled";
};

&power {
 status = "disabled";
};

&reg {
 status = "disabled";
};

&egu1 {
 status = "disabled";
};

&egu2 {
 status = "disabled";
};

&egu3 {
 status = "disabled";
};

&egu4 {
 status = "disabled";
};

&egu5 {
 status = "disabled";
};

&rng {
 status = "disabled";
};

&ppi {
 status = "okay";
};

&nvic {
 status = "disabled";
};

&clock {
 status = "okay";
};

&uicr {
 status = "disabled";
};

&mwu {
 status = "disabled";
};

&wdt {
 status = "disabled";
};

RE: Baseline Power Consumption Benchmarking on nrf52dk

Vidar Berg — Mon, 09 Feb 2026 13:44:08 GMT

The configuration I showed is only supplying the nRF on chip on P22, and with this configuration, the USB should remain connected to supply the interface MCU and LEDs.

RE: Baseline Power Consumption Benchmarking on nrf52dk

federicoc — Fri, 06 Feb 2026 16:46:29 GMT

I agree Vidar,

something is off, and probably is my nrf52DK.

My understanding is that I should be able to configure Source Measurement as displayed in this video (min 6: 13) and use the ppk as external power supply:
https://www.youtube.com/watch?v=B42lPvkUSoc

and/ following the following links:

https://docs.nordicsemi.com/bundle/ug_ppk2/page/UG/ppk/measure_current_source_meter.html

https://docs.nordicsemi.com/bundle/ug_nrf52832_dk/page/UG/dk/prepare_board.html

In Source Measurement, if is the ppk to supply voltage, I would need to solder SB12.

Now, in my case supplying the voltage to the ppk without the USB connected via the External Supply pins does not work even after soldering SB12.

It seems that the only way I get power to the chip is by connecting the USB from the nrf52dk to the PC.

RE: Baseline Power Consumption Benchmarking on nrf52dk

Vidar Berg — Fri, 06 Feb 2026 06:28:01 GMT

This is closer to expected results, but I am afraid the measurement is too low now to be valid. Did you use the same supply voltage as I did in the other post? It is important that it matches the VDD (~2.9V) on the board to avoid leakage from the USB supply.

RE: Baseline Power Consumption Benchmarking on nrf52dk

federicoc — Thu, 05 Feb 2026 18:58:21 GMT

Thank you Vidar,

after reviewing the post, I noticed that to measure the current in source meter mode I had to cut SB9 bridge and use two USB cables as detailed in

https://docs.nordicsemi.com/bundle/ug_ppk2/page/UG/ppk/measure_current_source_meter.html.

Now I am measuring 9.14 nA of floor current, which seems more in line with your data, but very low considering that it should average at around 300 nA from specs

RE: Baseline Power Consumption Benchmarking on nrf52dk

Vidar Berg — Thu, 05 Feb 2026 06:21:49 GMT

Hello,

The RTOS scheduler enters the IDLE thread when there is no work to do and puts the chip into sleep mode (System ON). In this state, the system run current should be only a couple of microamps provided no peripherals are active during sleep that keep the HF clock running. This is also the floor current you should expect to measure with most SDK samples when UART is disabled (set CONFIG_SERIAL=n in your project configuration). With UART enabled for logging, you may measure around 600 uA.

[quote user=""]Currently, the kit reads about 23.25 mA while running in the main loop. Does this seem reasonable?[/quote]

This is way more than what you should expect to see. Unless you are using GPIO outputs to drive external loads, the chip itself should never draw this much current. Does your measurement setup match what I described in this post here: /f/nordic-q-a/120743/ble-advertising-power-benchmark/532498?

Best regards,

Vidar