High Power consumption issue in Nrf54L15 during system off (low power state)

RE: High Power consumption issue in Nrf54L15 during system off (low power state)

Syed Maysum Abbas Zaidi — Thu, 26 Feb 2026 09:01:28 GMT

Hi,

Thanks for sharing the schematic snippet, we will review it and get back to you on that private ticket.

Best Regards,
Syed Maysum

RE: High Power consumption issue in Nrf54L15 during system off (low power state)

CYRUS AG — Wed, 25 Feb 2026 14:32:55 GMT

As the schematic contains project-specific confidential details, I have created a separate private support ticket to share the schematic snippet securely.

Private ticket case ID: 357608

Please continue the technical review in the private ticket.

Thanks!

[quote userid="149180" url="~/f/nordic-q-a/127086/high-power-consumption-issue-in-nrf54l15-during-system-off-low-power-state/562042"]

Can you share the schematic snippet as well

[/quote]

RE: High Power consumption issue in Nrf54L15 during system off (low power state)

Syed Maysum Abbas Zaidi — Wed, 25 Feb 2026 13:16:40 GMT

Hi,

The 0.7-0.9 µA System OFF figures in the Nordic datasheet refer to the nRF54L15 SoC itself under ideal conditions (no RAM retention, minimal wake sources). On a module like BM15C, additional on‑module circuitry (regulator, pull‑ups, other ICs, etc.) can add to this, which likely explains the extra ~80 µA you are seeing.

Can you share the schematic snippet as well

Best Regards,
Syed Maysum

RE: High Power consumption issue in Nrf54L15 during system off (low power state)

CYRUS AG — Tue, 24 Feb 2026 16:10:57 GMT

Hi Syed,

Thanks for the clarification. The same hardware setup was previously consuming around 8 µA in deep sleep when using the ESP32-C3, so with BM15C I expect the consumption to be similar or lower. Currently, I am observing around ~80 µA in deep sleep for these measurements, I have disabled the J-Link RTT connection.

RE: High Power consumption issue in Nrf54L15 during system off (low power state)

Syed Maysum Abbas Zaidi — Mon, 23 Feb 2026 13:38:55 GMT

Hi,

Okay, thanks for keep trying out the possible solutions.

It means even after disabling the RAM retention, all wakeups sources and implementing Errata 37 workaround, there is no change in the results. Then we need to be be sure you are measuring current only into the BM15C supply pin(s), not the whole board rail or hardware setup (so the ammeter only sees the SoC, not the rest of the board). Also temporarily disconnect or powergate any other loads on that rail.

Measure and see if you see any drop in current.

Best Regards,
Syed Maysum

RE: High Power consumption issue in Nrf54L15 during system off (low power state)

CYRUS AG — Mon, 23 Feb 2026 11:09:02 GMT

[quote userid="149180" url="~/f/nordic-q-a/127086/high-power-consumption-issue-in-nrf54l15-during-system-off-low-power-state/561795"]nRF54L15 errata [/quote]

https://docs.nordicsemi.com/bundle/errata_nRF54L15_EngB/page/ERR/nRF54L15/EngineeringB/latest/err_L15_new.html

I also tried the workaround mentioned in the nRF54L15 Engineering B errata documentation, but there is no change in the results.

RE: High Power consumption issue in Nrf54L15 during system off (low power state)

Syed Maysum Abbas Zaidi — Mon, 23 Feb 2026 08:53:01 GMT

Hi,

Thanks for sharing your observations.

You now may need to check the build code of your SoC as there is a nRF54L15 errata which says: if entering System OFF too soon after pin reset/power cycle, current can be higher than expected.

If your SoC build code is one of the following: QFAA-C00, CAAA-C00, QDAA-C00, QGAA-C00 or QFAA-BB0, CAAA-BA0 then try applying the following workaround.

Right before the sys_poweroff(), add:

*(volatile uint32_t *)0x5005340C = 1;

/* Ensure at least 40 CPU cycles before entering System OFF.
 * A simple NOP loop or a small delay function is enough.
 */
for (volatile int i = 0; i < 100; i++) {
    __NOP();
}

sys_poweroff();

Best Regards,
Syed Maysum

RE: High Power consumption issue in Nrf54L15 during system off (low power state)

CYRUS AG — Fri, 20 Feb 2026 12:15:13 GMT

Additionally, I tried applying the change in the overlay DTS, but the results remain the same as mentioned earlier.

I added the following,

&vregmain {
regulator-initial-mode = <NRF5X_REG_MODE_DCDC>;
};

However, there was no observable difference in current consumption.

RE: High Power consumption issue in Nrf54L15 during system off (low power state)

CYRUS AG — Fri, 20 Feb 2026 11:40:16 GMT

[quote userid="149180" url="~/f/nordic-q-a/127086/high-power-consumption-issue-in-nrf54l15-during-system-off-low-power-state/561682"]Please measure the current in this configuration and let us know the result, along with how the board is powered and where exactly you insert the ammeter or PPK.[/quote]

Hi Syed,

Thanks for the suggestions.

I tested with the recommended changes in prj.conf. This time I checked the behavior with J-Link connected, and the results are still similar. During the ON state, the consumption is around 4.20 mA, and in System OFF it initially shows about 219.2 µA, but after waiting for around 5 to 8 seconds, the current drops to 83.8 µA(this happens occasionally).

Without J-Link connected, the ON state consumption is again 4.20 mA, but the device does not appear to enter System OFF based on the current measurement. This is my observation so far.

For reference, this is my prj.conf configuration:

CONFIG_PM_DEVICE=y
CONFIG_GPIO=y
CONFIG_POWEROFF=y
CONFIG_HWINFO=y

CONFIG_USE_SEGGER_RTT=n
CONFIG_RTT_CONSOLE=n
CONFIG_UART_CONSOLE=n

CONFIG_GPIO_WAKEUP_ENABLE=n
CONFIG_GRTC_WAKEUP_ENABLE=n
CONFIG_LPCOMP_WAKEUP_ENABLE=n

The ammeter is connected in series between the battery(3.7V, 120mA) and the device for measurement. Tests are performed both with J-Link connected (for logging/behavior verification) and with it disconnected.

Please let me know if you would like me to check anything else.

Thanks!

RE: High Power consumption issue in Nrf54L15 during system off (low power state)

Syed Maysum Abbas Zaidi — Fri, 20 Feb 2026 10:31:36 GMT

Hi,

Hi, thanks for confirming. When measuring the System OFF current, could you please confirm whether this was done with the debugger/SWD physically disconnected and with RTT disabled? A connected debug probe can significantly affect low power current measurements.

As the next check, could you also try building with all wake sources disabled by adding the following to your prj.conf:

CONFIG_GPIO_WAKEUP_ENABLE=n
CONFIG_GRTC_WAKEUP_ENABLE=n
CONFIG_LPCOMP_WAKEUP_ENABLE=n

We want to rule out a case where a wake source (GPIO level wake or GRTC) is active continuously, causing the device to enter System OFF and then wake immediately in a loop, which can show up as a much higher current. With all wake sources disabled, the device should enter System OFF and stay there until reset/power-cycled.

Please measure the current in this configuration and let us know the result, along with how the board is powered and where exactly you insert the ammeter or PPK.

Best Regards,
Syed Maysum

RE: High Power consumption issue in Nrf54L15 during system off (low power state)

CYRUS AG — Fri, 20 Feb 2026 07:55:18 GMT

Hi Syed,

I have checked the logs, and the device is entering System OFF. However, there is no significant difference in current consumption — the result remains around ~220 µA.

Here is sample,
devzone.nordicsemi.com/.../6254.system_5F00_off.zip

Thanks!

RE: High Power consumption issue in Nrf54L15 during system off (low power state)

Syed Maysum Abbas Zaidi — Thu, 19 Feb 2026 14:41:06 GMT

Hi,

Okay, it looks we may need to confirm if the sample is actually entering the System OFF. Can you check the logs or if possible to share it as in the system_off sample, System OFF is entered only if console suspend succeeds. If console suspend fails, the app prints "Could not suspend console" and returns without calling sys_poweroff().

Similarly when waking up there should be a message confirming it.

Best Regards,
Syed Maysum

RE: High Power consumption issue in Nrf54L15 during system off (low power state)

CYRUS AG — Thu, 19 Feb 2026 13:25:42 GMT

Hi Syed,

I have tried the above lines, but the results are the same (216.4 µA). It didn’t work at all. Also, I have tried this on another identical device to ensure the device is working properly, but the results are the same.

Thanks!

RE: High Power consumption issue in Nrf54L15 during system off (low power state)

Syed Maysum Abbas Zaidi — Thu, 19 Feb 2026 13:02:43 GMT

Hi,

The issue could be due to RAM retention, you may need to disable it which should not be a issue as chip will reset upon wakeup. To make this happen, can you try adding the following lines before calling system OFF:

NRF_MEMCONF->POWER[0].RET = 0;
NRF_MEMCONF->POWER[1].RET = 0;
NRF_MEMCONF->POWER[0].RET2 = 0;
NRF_MEMCONF->POWER[1].RET2 = 0;

You may able to reduce the extra current consumption.

Best Regards,
Syed Maysum