nRF9151 SMA DK + CMW500: How to run NB-IoT NTN and do IP connectivity test (ping/iperf)

RE: nRF9151 SMA DK + CMW500: How to run NB-IoT NTN and do IP connectivity test (ping/iperf)

Kenneth — Thu, 26 Mar 2026 22:28:58 GMT

I was kind of hoping for more descriptive answer from the team, but the short answer I could get from one of the members was: "About other questions, I think for example customers findings about the attach levels are pretty much right".

Kenenth

RE: nRF9151 SMA DK + CMW500: How to run NB-IoT NTN and do IP connectivity test (ping/iperf)

yuki — Wed, 18 Mar 2026 13:22:32 GMT

Sorry for the late response.

Thanks for your guidance. I was able to resolve the TX output power issue using the settings you suggested.

I would appreciate your comments on the remaining questions as well when you have time.

RE: nRF9151 SMA DK + CMW500: How to run NB-IoT NTN and do IP connectivity test (ping/iperf)

Kenneth — Tue, 10 Mar 2026 14:05:59 GMT

Hello,

[quote user="yuki01"]・TX output power always at maximum and preventing idle disconnect
Is my understanding correct that there is no UE‑side setting to force the terminal to always transmit at maximum output power, or to prevent the connection from being released even in idle conditions?
Do I have to adjust the network side settings?[/quote]

As default in NB1-mode the DL power level received by the UE affects its UL power level.

One way to force DUT to use max Pout level is to LOWER DL level ~10dB AFTER establishing a call.

Another way is to “decouple” UL and DL power levels in CMW settings by enabling Advanced Power Control and setting pathloss compensation to zero.

For max UL Pout the settings can be something like this:

Waiting for feedback on your other questions.

Kenneth

RE: nRF9151 SMA DK + CMW500: How to run NB-IoT NTN and do IP connectivity test (ping/iperf)

yuki — Thu, 05 Mar 2026 15:39:53 GMT

Thank you for the guidance. With the steps you shared, I successfully established connectivity with the CMW500 emulator and verified end‑to‑end communication.

I have a few follow‑up questions.

・TX output power always at maximum and preventing idle disconnect
Is my understanding correct that there is no UE‑side setting to force the terminal to always transmit at maximum output power, or to prevent the connection from being released even in idle conditions?
Do I have to adjust the network side settings?

・Cellular Monitor shows everything as Unknown
In my setup, the Cellular Monitor app shows all fields as Unknown, which makes debugging difficult.
Could this be due to the NTN modem firmware being an alpha release?
For example, even with a combination such as "mfw_nrf9151-ntn_1.0.0-1.alpha.zip" and
"serial_modem_v0.3.0_nrf9151dk_ppp_cmux_mtrace.hex", is it possible to see logs in Cellular Monitor if the firmware is rebuilt with the required settings enabled in nRF Connect SDK (VS Code)?
This point is not clear to me.

・Measured C/N threshold difference between attach and maintain
I measured the minimum C/N for attach to be around −2 dB, while the minimum C/N to keep the connection stable was around −5 dB
The troubleshooting material I found does not provide specific numeric thresholds, so I want to confirm whether a ~3 dB gap between “attach” and “maintain” is a normal/expected behavior for NB‑IoT NTN testing in this type of setup

Thank you in advance.

yuki

RE: nRF9151 SMA DK + CMW500: How to run NB-IoT NTN and do IP connectivity test (ping/iperf)

Kenneth — Mon, 02 Mar 2026 08:53:24 GMT

Hello,

The feedback I received:

nRF9151 SMA DK - Evaluate NTN - nordicsemi.com

You will need to follow the guides in the above webpage. Recommend to use Serial Modem add-on, ICMP AT commands and more generic info in Serial Modem.

NTN evaluation guide indicates Serial Modem 0.3.0, but there’s also now 1.0.0 so either will work.

AT%xsystemmode=0,0,0,0,1 - sets system mode to NB NTN

AT%xbandlock=2,,"255" - sets bandlock for example to band 255

at%location=2,"25.08439333","121.56076999","0",0,0 - sets UE location (default 3GPP GSO location specified in 3GPP 36.508 chapter 4.13).

AT%XLABAPP=12,1 - deactivates UE prediction of satellite trajectory if required.

The team have tested CMW500 NBIOT FW version 4.0.250 which has support for NTN. It has many satellite scenarios for NTN:

x For “GEO - Zero Delay” location needs to be Lat-"0.0" Long-"121.561" Alt-"35785998.3"

For RF-related testing I have used scenario “GSO - RF”.

Hope this helps,
Kenneth

RE: nRF9151 SMA DK + CMW500: How to run NB-IoT NTN and do IP connectivity test (ping/iperf)

Kenneth — Wed, 25 Feb 2026 12:42:31 GMT

Hello,

Let me check internally and get back to you. May take a few days.

Kenneth