PCA10056 dev board jumps to hard fault exception when running ble mesh switch example

RE: PCA10056 dev board jumps to hard fault exception when running ble mesh switch example

Mttrinh — Thu, 25 Oct 2018 12:47:38 GMT

I have tried with a couple of boards and can't seem to reproduce. Weird that it is only happening to one of your boards...

Is the all the boards new?

RE: PCA10056 dev board jumps to hard fault exception when running ble mesh switch example

PaulH — Mon, 22 Oct 2018 13:33:00 GMT

No, I don't provision it. Just run it in debug mode and wait

RE: PCA10056 dev board jumps to hard fault exception when running ble mesh switch example

Mttrinh — Mon, 22 Oct 2018 12:46:11 GMT

Do you provision it first before you leave it until it goes into hardfault? Or just go into debug mode and leave it running?

RE: PCA10056 dev board jumps to hard fault exception when running ble mesh switch example

Mttrinh — Wed, 17 Oct 2018 15:18:19 GMT

I will test this with the boards on my desk and update you with my findings. Also, can you try to download a fresh copy of the SDK and try again? Don't think it will make any difference but it is worth a shot.

UPDATE: I have let the board running all day, haven't managed to reproduce your issue yet. Will try with a couple of other boards and see if I can repproduce it.

RE: PCA10056 dev board jumps to hard fault exception when running ble mesh switch example

PaulH — Fri, 12 Oct 2018 08:17:10 GMT

I am using SES Release 3.30 Build 2017101300.33948
From nrf5 SDK for Mesh v2.2.0 I compiled the proxy_server light_switch_proxy_server_nrf52840_xxAA_s140_6_0_0 project in Debug mode.

I have made no modifications to the project.

I connect to the PCA10056 dev board from the IDE and do an Erase All.

I then debug the project by clicking the play icon.

After a while (sometimes a few minutes, sometimes hours) the debug session stops if i then click the play icon to continue, it jumps to the fault vector.

I have added two screenshots to show this. The first is after the debugger stops itself. The stack trace is empty and it shows that it seems to try to go to an unknown function at address 0x00000978. When debug is resumed it goes to the hard fault handler as shown in the second screenshot.

RE: PCA10056 dev board jumps to hard fault exception when running ble mesh switch example

Mttrinh — Tue, 09 Oct 2018 15:46:28 GMT

Can you give me a step by step procedure on how to reproduce this and I will test this over here? Also is the SoftDevice fault handler called?

RE: PCA10056 dev board jumps to hard fault exception when running ble mesh switch example

PaulH — Fri, 05 Oct 2018 09:45:56 GMT

I have tried programming the three boards with the light_switch proxy_client and it does behave exactly the same, the board labelled 0.9.2 jumps to the hard fault handler but the other two boards do not.

I only have these three boards to test with.

I tried a full erase using nrfjprog first but this made no difference.

As an experiment, I tried building the projects as release builds rather than debug (as I always have previously) and in release mode they do not crash.

When the board crashes in debug mode, generally the stack trace is empty which isn't very helpful. Once when it crashed I had the following stack trace but I'm not sure it is any help :-

RE: PCA10056 dev board jumps to hard fault exception when running ble mesh switch example

Mttrinh — Thu, 04 Oct 2018 11:31:28 GMT

Hi,

This seems like a strange issue. Can you try the same setup with the light_switch proxy_client and see if things behaves the same way? Do you have another PCA10056 board with the same version that you can test with?

Also, can you try full erase with nrfjprog before flashing the boards?