Scanning mobile phone MAC address

RE: Scanning mobile phone MAC address

bjorn-spockeli — Tue, 29 Jan 2019 07:37:02 GMT

Q1: The Bluetooth Services available in the nRF5x SDK are listed under BLE Services in the SDK documentation.

Q2: The Bluetooth Mesh does not use services, but models, see Basic Bluetooth Mesh concepts. The supported models are listed in the nRF5 SDK for Bluetooth Mesh documentation, see Mesh Models

RE: Scanning mobile phone MAC address

Sunil vignesh — Tue, 29 Jan 2019 06:20:21 GMT

Hi ,

For my knowledge

could you please tell me

What are the BLE_SERVICE available for Bluetooth peripheral ?

What are the BLE_SERVICE available for Bluetooth MESH?

RE: Scanning mobile phone MAC address

bjorn-spockeli — Fri, 25 Jan 2019 08:18:21 GMT

Q1: I meant the BLE stack on the mobile phone side.

Q2: No, a list of the available examples for Bluetooth Mesh can be found here.

RE: Scanning mobile phone MAC address

Sunil vignesh — Fri, 25 Jan 2019 06:54:14 GMT

I will refer the tutorial.

[quote userid="7571" url="~/f/nordic-q-a/42894/scanning-mobile-phone-mac-address/167708"]but you will have to check the BLE stack specification [/quote]

I need to check in SDK15.2 or particular mobile phone specification

[quote userid="7571" url="~/f/nordic-q-a/42894/scanning-mobile-phone-mac-address/167708"]Do you mean UART over BLE or a wired UART interface to control a BLE Mesh node?[/quote]

UART over BLE_MESH

is there any example UART OVER BLE_MESH network

RE: Scanning mobile phone MAC address

bjorn-spockeli — Thu, 24 Jan 2019 15:34:02 GMT

I would refer you to the BLE Low Energy Getting Started tutorials found here. You can also look at the ble_app_uart peripheral example and the ble_app_uart_c central examples in the SDK

Yes, mobilephones my act as peripherals, but you will have to check the BLE stack specification to verify that this is supported.

Do you mean UART over BLE or a wired UART interface to control a BLE Mesh node?

RE: Scanning mobile phone MAC address

Sunil vignesh — Thu, 24 Jan 2019 11:03:08 GMT

[quote userid="7571" url="~/f/nordic-q-a/42894/scanning-mobile-phone-mac-address/167388"] MAC address and device name is placed in the advertisment packet[/quote]

Sir, Is there any code related to explain advertising with name and MAC address .

how central scan and connect with peripherals any tutorial means please share with me .

[quote userid="7571" url="~/f/nordic-q-a/42894/scanning-mobile-phone-mac-address/167388"]If the mobile phones are advertising and the MAC address is placed in the advertisement packet. [/quote]

Is BLE_CENTRAL code can able to scan and connect with Bluetooth Mobile phones???

(Note: This is one particular application where our device has to act as central (master). mobile phone has to act as peripheral (slave).

our device has to scan the near by mobile phones and device only decide to connect with particular mobile phone).

Is there any code related to UART communication in BLE_MESH (v3.0)

RE: Scanning mobile phone MAC address

bjorn-spockeli — Wed, 23 Jan 2019 13:57:27 GMT

HI Sunil,

Q1: If the MAC address and device name is placed in the advertisment packet, then yes.

Q2: If the mobile phones are advertising and the MAC address is placed in the advertisement packet.

Our BLE protocol stacks ( SoftDevices) support upto 20 concurrent connections so the nRF52832 or nRF52840 should be a good for your customers application. The NRF52840 is able to transmit at +8dBm, so if you require long range, then I would go for this IC.

Best regards
Bjørn

RE: Scanning mobile phone MAC address

bjorn-spockeli — Wed, 23 Jan 2019 13:57:26 GMT

HI Sunil,

Q1: If the MAC address and device name is placed in the advertisment packet, then yes.

Q2: If the mobile phones are advertising and the MAC address is placed in the advertisement packet.

Best regards
Bjørn