Can Softdevice RTC be used without an interrupt handler?

RE: Can Softdevice RTC be used without an interrupt handler?

kjhuebner — Thu, 20 Aug 2020 10:38:45 GMT

If my memory serves me right -- I confirmed the RTC2 clock rate by creating a program loop that polls the RTC2 clock value and toggling an IO pin. Then while the Nordic device is running, observing the IO pin using an oscilloscope.

The pseudo code looks like this...

unsigned int read_value;

while(true)

{

read_value= RTC2 clock value ;

while (read_value == RTC2 clock value)

;

set IO pin = high

read_value= RTC2 clock value ;

while (read_value == RTC2 clock value)

;

set IO pin = low

}

Keep in mind for the above code... your logic analyzer will show a

frequency rate= desired RTC2 clock rate divided by 2.

The reason is the above code has a toggle high and a toggle low for each full wave of output signal. I think you get the picture.

ALTERNATIVE SOLUTION:

One could read RTC2 clock into "read_value", then add 1000 to read_value, then poll the RTC2 clock until it reaches the value, then toggle IO pin. This would avoid the possibility of missing clock ticks if your RTC2 clock rate is exceptionally high. Of course in this case, your oscilloscope or logic analyzer will show a

frequency rate= desired RTC2 clock rate divided by 2000.

-Ken

RE: Can Softdevice RTC be used without an interrupt handler?

Zoran — Thu, 20 Aug 2020 07:33:58 GMT

Hi Ken,
i just implemented your solution and it works well. Thanks for providing this.

I want to confirm my RTC 2 clock rate with my logic analyzer. How did you do this without a handler?

RE: Can Softdevice RTC be used without an interrupt handler?

kjhuebner — Wed, 13 Mar 2019 20:28:53 GMT

Kenneth - Your solution #4 seems best. If I have time, I may go with it instead.

One day... maybe Nordic will provide a proper solution and allow developers to use RTC clocks without handlers.

RE: Can Softdevice RTC be used without an interrupt handler?

kjhuebner — Wed, 13 Mar 2019 20:17:05 GMT

Forgot one item: place this at top of source file.

const nrf_drv_rtc_t m_rtc = NRF_DRV_RTC_INSTANCE(2); /**< Declaring an instance of nrf_drv_rtc for RTC2. */

RE: Can Softdevice RTC be used without an interrupt handler?

kjhuebner — Wed, 13 Mar 2019 20:08:02 GMT

Hi, Thanks for your notes. My solution to avoid using an RTC handler was to call Nordic's "Softdevice 132" low level functions. The following compiles and runs fine, with a confirmed 8192 hz RTC clock rate. No handler required. The one caveat is I'm not sure how stable and long lasting the API will be, recognizing these are low level functions.

-Ken

SOLUTION:

    //Set RTC config to default.
    nrf_drv_rtc_config_t rtc_config = NRF_DRV_RTC_DEFAULT_CONFIG;

#define APP_RTC_CLOCK_FREQ       8192    //hz
    rtc_config.prescaler = 3;     //resulting freq= 8192 hz.

    NRFX_IRQ_PRIORITY_SET(m_rtc.irq, rtc_config.interrupt_priority);
    NRFX_IRQ_ENABLE(m_rtc.irq);
    nrf_rtc_prescaler_set(m_rtc.p_reg, rtc_config.prescaler);

    //Enable Nordic RTC.
    nrf_rtc_task_trigger(m_rtc.p_reg, NRF_RTC_TASK_START);    //RUNTIME RTC2 WORKS OK!

RE: Can Softdevice RTC be used without an interrupt handler?

Kenneth — Wed, 13 Mar 2019 19:05:48 GMT

Hi,

I see your point, but I don't have any good workarounds here other than to suggest a few more possibilities:

3. the rtc interrupt may be set to occur very infrequent, in other words every ~30minutes, I doubt that will be measurable on average current.

4. you may just disable the interrupt manually after starting the clock by the driver by calling NRF_RTC1->INTENCLR (a hack I know)

Best regards,
Kenneth