NRF52810 // nRF5_SDK_15.3.0_59ac345 // pca10040e // functions (example ble_stack_init()) // causing problems

RE: NRF52810 // nRF5_SDK_15.3.0_59ac345 // pca10040e // functions (example ble_stack_init()) // causing problems

awneil — Thu, 09 May 2019 08:52:13 GMT

You're welcome.

Please verify the answer:

RE: NRF52810 // nRF5_SDK_15.3.0_59ac345 // pca10040e // functions (example ble_stack_init()) // causing problems

Florian — Thu, 09 May 2019 08:34:49 GMT

So it worked a lot better. im comming through the INIT Functions and Im able to connect via the NORDIC Toolbox App. i think the Problem is (at least for the Moment) solved. I will be checking the other functions in an Month.

I did all the changes from the Link:

https://rigado.zendesk.com/hc/en-us/articles/225674668-Example-files-will-not-run-on-my-hardware-LF-Clock-Source-Selection

(only above The instructions below apply to Nordic SDK v11.x.x and earlier.)

Thank you awneil. you helped a lot =)

RE: NRF52810 // nRF5_SDK_15.3.0_59ac345 // pca10040e // functions (example ble_stack_init()) // causing problems

awneil — Wed, 08 May 2019 14:53:02 GMT

[quote userid="78416" url="~/f/nordic-q-a/47061/nrf52810-nrf5_sdk_15-3-0_59ac345-pca10040e-functions-example-ble_stack_init-causing-problems/186013"]do i have to change the SDK if i dont have one[/quote]

You have to configure it correctly (in sdk_config.h) to match whatever clock source(s) your app is using.

The Rigado post linked from that post gives a good description of how to configure for no external crystal, and is not specific to Rigado.

RE: NRF52810 // nRF5_SDK_15.3.0_59ac345 // pca10040e // functions (example ble_stack_init()) // causing problems

Florian — Wed, 08 May 2019 14:38:31 GMT

So that seems intresting. I dont have an external 32.768 kHz Oscilator... So im going through the other Post tomorrow. The Short form: do i have to change the SDK if i dont have one?

RE: NRF52810 // nRF5_SDK_15.3.0_59ac345 // pca10040e // functions (example ble_stack_init()) // causing problems

awneil — Wed, 08 May 2019 14:30:22 GMT

The question is, do you initialise your application according to whatever crystals you have or haven't fitted...?

https://devzone.nordicsemi.com/f/nordic-q-a/46564/error-133-0x85-gatt-error-on-nrf52840/185362#185362

RE: NRF52810 // nRF5_SDK_15.3.0_59ac345 // pca10040e // functions (example ble_stack_init()) // causing problems

Florian — Wed, 08 May 2019 14:25:06 GMT

Do you initial the cristals?

RE: NRF52810 // nRF5_SDK_15.3.0_59ac345 // pca10040e // functions (example ble_stack_init()) // causing problems

awneil — Wed, 08 May 2019 14:22:44 GMT

pardon?

RE: NRF52810 // nRF5_SDK_15.3.0_59ac345 // pca10040e // functions (example ble_stack_init()) // causing problems

Florian — Wed, 08 May 2019 14:16:37 GMT

which you initial?

RE: NRF52810 // nRF5_SDK_15.3.0_59ac345 // pca10040e // functions (example ble_stack_init()) // causing problems

awneil — Wed, 08 May 2019 14:13:17 GMT

and the crystals

RE: NRF52810 // nRF5_SDK_15.3.0_59ac345 // pca10040e // functions (example ble_stack_init()) // causing problems

Florian — Wed, 08 May 2019 14:00:29 GMT

jeah But since the GPIO Examples are running there is not much about the hardware that could be Wrong... theres only the Antenna and the Matching circuit on the RF site which are both not used in the initialization....

RE: NRF52810 // nRF5_SDK_15.3.0_59ac345 // pca10040e // functions (example ble_stack_init()) // causing problems

awneil — Wed, 08 May 2019 13:54:56 GMT

I would strongly suggest that you do get one!

It's far easier to start with a known-good hardware platform, and known-good software examples, and to have a known-good reference!

At the moment the problem(s) could be in your hardware, or your software - or both!

For nRF52810, you will need to use the nRF52832-DK:

https://devzone.nordicsemi.com/f/nordic-q-a/33812/developing-for-nrf52810---the-full-story

RE: NRF52810 // nRF5_SDK_15.3.0_59ac345 // pca10040e // functions (example ble_stack_init()) // causing problems

Florian — Wed, 08 May 2019 13:51:17 GMT

i Dont have one... so im not sure. But im using the nRF52810-QCAA-T with 32Bit its not exactly the same...

RE: NRF52810 // nRF5_SDK_15.3.0_59ac345 // pca10040e // functions (example ble_stack_init()) // causing problems

awneil — Wed, 08 May 2019 13:45:26 GMT

Does it work on the Nordic DK ?