Radio Test - Logging Results in RX Sweep

RE: Radio Test - Logging Results in RX Sweep

Håkon Alseth — Thu, 11 Jul 2019 12:57:56 GMT

Hi Roman,

The call to "radio_rx()" does not wait until the radio is up and running. if you add a small delay (130 us + a bit of extra margin, lets say 200 us in total), it should properly log the RSSI.

Remember to read out the RSSI as a negative number (rssi = -rssi;).

Kind regards,

Håkon

RE: Radio Test - Logging Results in RX Sweep

romc — Thu, 11 Jul 2019 07:09:47 GMT

I try to help him and use the following code:

/*active RX MODE*/
radio_rx(mode, m_channel);

/*start single RSSI Measurement*/
NRF_RADIO->TASKS_RSSISTART = 1;

/*wait until the measurement is running*/
while(NRF_RADIO->EVENTS_RSSIEND == 0);

/*overwrite this events*/
NRF_RADIO->EVENTS_RSSIEND = 0;
/*sample the RSSI Value*/
rssi = (int8_t)NRF_RADIO->RSSISAMPLE;

/*print the rssi value and channel information*/
nrf_cli_fprintf(p_cli_test, NRF_CLI_NORMAL, "RSSI:%d, Channel: %d \r\n",rssi,m_channel);

but on the UART we see always 127.

If i start a debug session, and we go step by step inside the code then we see normal rssi values.

What we do wrong?

Best Regards,

Roman

RE: Radio Test - Logging Results in RX Sweep

Håkon Alseth — Tue, 09 Jul 2019 13:42:55 GMT

Hi,

Sorry, I assumed that you wanted to get the RSSI on address match (ie: receiving a valid packet).

You do not need to do this on a interrupt level.

If you just want to sample the noise level, you can do something like this:

NRF_RADIO->TASKS_RSSISTART = 1;
while (NRF_RADIO->EVENTS_RSSIEND == 0);
NRF_RADIO->EVENTS_RSSIEND = 0;
int8_t rssi = NRF_RADIO->RSSISAMPLE;

This assumes that you are already in RX mode.

Kind regards,

Håkon

RE: Radio Test - Logging Results in RX Sweep

ZAC — Tue, 09 Jul 2019 12:44:36 GMT

Hi,

we are trying to implement the above suggestion. Here's how the actual modification looks like:

if (NRF_TIMER0->EVENTS_COMPARE[0])

{

NRF_TIMER0->EVENTS_COMPARE[0] = 0;

if (m_sweep_tx)

{

radio_unmodulated_tx_carrier(txpower, mode, m_channel);

}

else if (m_sweep_rx)

{

if(NRF_RADIO->EVENTS_RSSIEND == 1)

{

uint8_t rssi_value= NRF_RADIO->RSSISAMPLE;

nrf_cli_fprintf(p_cli_test, NRF_CLI_NORMAL, "RSSI:%d, Channel: %d\r\n",rssi_value,m_channel-1);

}

radio_rx(mode, m_channel);

}

else

{

//Do nothing

}

m_channel++;

if (m_channel > channel_end)

{

m_channel = channel_start;

}

EVENTS_RSSIEND had to be manually added but it appears nowhere in the radio test example.

After flashing start_rx_sweep did not return anything. So the questen is where and when will the EVENTS_RSSIEND be set?

As for the transmit, it is envisaged to use another board in transmit mode at a fixed channel (start_tx_carrier).

We expect the start_rx_sweep to function in a similar way like the start_tx_sweep.

The goal is to be able to read the RSSIs of the RX sweep for each channel.

RE: Radio Test - Logging Results in RX Sweep

Håkon Alseth — Fri, 05 Jul 2019 08:15:50 GMT

Hi,

[quote user=""]What commands to use to be able to log the measured received power values over UART and corresponding active receive channel?[/quote]

Unfortunately, the example does not print the RSSI value. If you require this functionality, you have to modify the example and add it manually, first by enabling the RSSI shorts in radio_test.c::radio_rx():

NRF_RADIO->SHORTS = RADIO_SHORTS_READY_START_Msk | RADIO_SHORTS_END_START_Msk | RADIO_SHORTS_DISABLED_RSSISTOP_Msk | RADIO_SHORTS_ADDRESS_RSSISTART_Msk;

You should then be able to read out the RSSISAMPLE register when EVENTS_RSSIEND is set.

Kind regards,

Håkon