zigbee

RE: zigbee

AndreasF — Mon, 14 Oct 2019 12:57:10 GMT

Hi.

As I said in my previous reply:

[quote user="AndreasF"][/quote]

You need to select a cluster to use for your end device.

I highly recommend that you read about Zigbee on the infocenter here.

You can not just send a random string with data.

Best regards,

Andreas

RE: zigbee

jagadeesh surneni — Mon, 14 Oct 2019 09:20:38 GMT

i want to send the following data:

"S_ID:9e4fed4e F_HEIGHT:.000000 B_VOLTAGE:12.31 TEMP:.000"

from end device to coordinator.

RE: zigbee

AndreasF — Mon, 14 Oct 2019 06:51:07 GMT

Hi.

[quote user="jagadeesh surneni"]please suggest me a example, to send 30 bytes of data from end device to coordinator.i am a beginner.[/quote]

This depends entirely on what you want to send in your network.

You need to select a cluster to use for your end device.

I highly recommend that you read about Zigbee on the infocenter here.

Atleast read these three:

Zigbee stack features – Includes an overview of the stack features and the supported standards.
Zigbee platform designs – Describes Zigbee protocol application architectures.
Programming principles – Provides information about application structure, debugging capabilities, and power optimization.

Best regards,

Andreas

RE: zigbee

jagadeesh surneni — Fri, 11 Oct 2019 11:10:41 GMT

connection is established between coordinator and router and end device. please suggest me a example, to send 30 bytes of data from end device to coordinator.i am a beginner.

Regards jagadeesh

RE: zigbee

AndreasF — Mon, 30 Sep 2019 12:13:06 GMT

Hi.

[quote user="jagadeesh surneni"]i have taken three boards. in one board i have dumped light coordinator code. and other two boards i have dumped light switch code.i am using internal clock.there is no network connection.[/quote]

Please take a look here and here how to test this example.

Best regards,

Andreas

RE: zigbee

awneil — Mon, 30 Sep 2019 10:11:08 GMT

[quote userid="79992" url="~/f/nordic-q-a/52631/zigbee/212511"]three boards[/quote]

What boards, exactly?

Are you getting any log messages?

What debugging have you done?

RE: zigbee

jagadeesh surneni — Mon, 30 Sep 2019 09:56:32 GMT

hi,

i have taken three boards. in one board i have dumped light coordinator code. and other two boards i have dumped light switch code.i am using internal clock.there is no network connection.

// <e> NRFX_CLOCK_ENABLED - nrfx_clock - CLOCK peripheral driver
//==========================================================
#ifndef NRFX_CLOCK_ENABLED
#define NRFX_CLOCK_ENABLED 1
#endif
// <o> NRFX_CLOCK_CONFIG_LF_SRC - LF Clock Source

// <0=> RC
// <1=> XTAL
// <2=> Synth
// <131073=> External Low Swing
// <196609=> External Full Swing

#ifndef NRFX_CLOCK_CONFIG_LF_SRC
#define NRFX_CLOCK_CONFIG_LF_SRC 0
#endif

// <o> NRFX_CLOCK_CONFIG_IRQ_PRIORITY - Interrupt priority

#ifndef NRFX_CLOCK_CONFIG_IRQ_PRIORITY
#define NRFX_CLOCK_CONFIG_IRQ_PRIORITY 6
#endif

/***********************************/

NRF_LOG_INFO("Joined network successfully");
bsp_board_led_on(ZIGBEE_NETWORK_STATE_LED);
nrf_gpio_pin_set(PAIR_LED);

/* Check the light device address */
if (m_device_ctx.bulb_params.short_addr == 0xFFFF)
{
zb_err_code = ZB_SCHEDULE_ALARM(find_light_bulb, param, MATCH_DESC_REQ_START_DELAY);
ZB_ERROR_CHECK(zb_err_code);
zb_err_code = ZB_SCHEDULE_ALARM(find_light_bulb_timeout, 0, MATCH_DESC_REQ_TIMEOUT);
ZB_ERROR_CHECK(zb_err_code);
param = 0; // Do not free buffer - it will be reused by find_light_bulb callback
}
}
else
{
NRF_LOG_ERROR("Failed to join network. Status: %d", status);
bsp_board_led_off(ZIGBEE_NETWORK_STATE_LED);
nrf_gpio_pin_clear(PAIR_LED);
zb_err_code = ZB_SCHEDULE_ALARM(light_switch_leave_and_join, 0, ZB_TIME_ONE_SECOND);
ZB_ERROR_CHECK(zb_err_code);

/****************************************/

Regards,

jagadeesh

RE: zigbee

awneil — Thu, 26 Sep 2019 12:22:01 GMT

Have you looked?