nRF9160 Custom PCB Programming - Using NRF91DK

RE: nRF9160 Custom PCB Programming - Using NRF91DK

Øyvind — Fri, 10 Jan 2020 12:28:39 GMT

Hello ychen,

Can you please register a new ticket for your question with all the relevant information, and the connection diagram that is missing?

Thank you!
-Øyvind

RE: nRF9160 Custom PCB Programming - Using NRF91DK

ychen — Fri, 10 Jan 2020 03:37:44 GMT

Hi Øyvind

I can't programing the target board.can you tell me On the "debugger" nrf9160DK ,What do I need to set?

I followed the Settings below:

On the "debugger" nrf9160DK, PC is connected to J4 through USB

I connected a 10pin cable from P22 (Debug Out) on the debugger board into P3 (nrf91 Debug in) on the target board.

On the target board, I select "nRF only" via SW1.

Connect a second USB cable to J4 on the target board. This will provide power on the target board.

Attached is my connection diagram

RE: nRF9160 Custom PCB Programming - Using NRF91DK

ychen — Tue, 07 Jan 2020 05:56:14 GMT

SW1 needs to be disconnected?

RE: nRF9160 Custom PCB Programming - Using NRF91DK

Øyvind — Fri, 03 Jan 2020 07:52:47 GMT

Very glad to hear that you solved the issue!

Kind regards,
Øyvind

RE: nRF9160 Custom PCB Programming - Using NRF91DK

GBSingh — Thu, 02 Jan 2020 18:06:23 GMT

I am powering the Custom PCB with the NRF91DK VDD Voltage , both are supposed to be operating at the same voltage levels .

A Few Updates

1. Removed a short in the Custom PCB due to poor soldering by PCBA (Multimeter didnt show a short , but the resistance between VDD and GND was really small )

2. Now IC responds when programming (nRF Connect Desktop 3.0.0) with SW11 turned to 3V (Doesn't respond in 1V8)

2020-01-02T17:30:42.011Z INFO Using nrfjprog to communicate with target
2020-01-02T17:30:44.238Z INFO Using J-Link Software version 6.54
2020-01-02T17:30:47.407Z INFO Segger serial: 960091668
2020-01-02T17:30:47.407Z INFO Segger speed: 2000 kHz
2020-01-02T17:30:47.407Z INFO Segger version: J-Link OB-K22-NordicSemi compiled Nov 7 2019 16:11:45
2020-01-02T17:30:47.410Z INFO Core probed: 960091668.
2020-01-02T17:30:47.411Z INFO Core RAM: 256KiB.
2020-01-02T17:30:47.411Z INFO Core ROM: 1024KiB in pages of 4KiB.
2020-01-02T17:30:47.683Z INFO Model: NRF9160_xxAA_FUTURE.
2020-01-02T17:30:47.688Z ERROR Error when getting device info: TypeError: First argument must be a unsigned integer
2020-01-02T17:30:47.688Z DEBUG getDeviceMemMap: First argument must be a unsigned integer

3. Checked (nRF Connect Desktop 3.3.0) SW turned to 3V -> Works !!

Using nrfjprog to communicate with target
2020-01-02T18:00:04.057Z INFO Using J-Link Software version 6.54
2020-01-02T18:00:06.134Z INFO Segger serial: 960091668
2020-01-02T18:00:06.135Z INFO Segger speed: 2000 kHz
2020-01-02T18:00:06.135Z INFO Segger version: J-Link OB-K22-NordicSemi compiled Nov 7 2019 16:11:45
2020-01-02T18:00:06.138Z INFO Core probed: 960091668.
2020-01-02T18:00:06.138Z INFO Core RAM: 256KiB.
2020-01-02T18:00:06.138Z INFO Core ROM: 1024KiB in pages of 4KiB.
2020-01-02T18:00:06.405Z INFO Model: NRF9160_xxAA_FUTURE.
2020-01-02T18:00:07.330Z INFO Core0: Reading device non-volatile memory. This may take a few seconds.
2020-01-02T18:00:16.734Z INFO Core0: Non-volatile memory has been read. 3 non-empty memory blocks identified

Thanks,

Gurbir Singh

RE: nRF9160 Custom PCB Programming - Using NRF91DK

Øyvind — Thu, 02 Jan 2020 14:35:16 GMT

Hello,

The image you provide seems correct. How are you powering your custom board? Do both boards have the same voltage level?

Kind regards,
Øyvind