How to measure RF power of nRF52840 DK

RE: How to measure RF power of nRF52840 DK

Sangbin — Tue, 28 Apr 2020 01:46:05 GMT

Thanks to your support, i can measure the continous wave signal perfectely.

Is it set up at 6dBm output right? (i attached photo which i measure)

so i appreciate that your kindly reply.

and i have some question about hex file which you attached.

I want to set up the signal output at -10 / 0 dBm.

But it is so difficult to me that fixing code because of hex file.

Can you support that this problem?

I would really appreciate that if you supported it as a hex file that can output -10dBm / 0dBm at the same frequency (2440MHz)

Best regard!

RE: How to measure RF power of nRF52840 DK

Andreas — Mon, 27 Apr 2020 12:11:45 GMT

Hi,

Not 100% sure with RBW=8MHz, try RBW=1MHz instead, but I think it is modulated yes.

FW for continuous wave is primarily radio test example in the SDK as mentioned, you can download this here:

Or flash this hex file, it just starts an unmodulated carrier on 2440 MHz: devzone.nordicsemi.com/.../nrf52_5F00_unmod_5F00_ch40_5F00_sleep.hex

Best regards,

Andreas

RE: How to measure RF power of nRF52840 DK

Sangbin — Mon, 27 Apr 2020 05:07:26 GMT

Hi. i'm using SA which named N9030B PXA.

when i measure triggered rf burst, it looks like modulated signal. (i attach photo)

so can you have any continous wave firmware or example code ?

RE: How to measure RF power of nRF52840 DK

Andreas — Fri, 24 Apr 2020 11:59:43 GMT

Hi,

OK, try updating to update to latest version (v3.3.3) and see if you can select constant then. Alternatively flash your board with the radio test example, found in our SDK under /examples/peripheral/radio_test/

As you say the PRBS and the other packet contents are bursted transmissions, or the packets are sent with a delay between each one. This is per the DTM spec. I am not sure I understand exactly how you trigger, but you do not need to worry about trigger at all. Just configure the spectrum analyzer to use peak detector and trace max hold. It will then report the peak sample measured at each sweep, and update the trace only if the measured value is higher than the previous one at that point in frequency. Which spectrum analyzer are you using?

Best regards,

Andreas

RE: How to measure RF power of nRF52840 DK

Sangbin — Fri, 24 Apr 2020 01:46:05 GMT

Thank you for your kind reply!

I have more question.

I'm using nRF connect v3.3.1 and lunch app named "Direct Test Mode".

As your reply, "packet type" has constant option. but i can't find them. (so i attach my lunch app screenshot)

please confirm part that filled yellow.

So in my situation, i'm using packet type which named "PRBS9"

It also make it tx signal, but it is brusted rf signal.

I can measure rf power at trigger mode of Signal analyzer. but not incorrect power i guess.

Can you check my attached picture and help to find solve this problem? (using constant power)

Have a nice day!

Best regards.

RE: How to measure RF power of nRF52840 DK

Andreas — Thu, 23 Apr 2020 12:53:02 GMT

Hi,

1. You can click the 'Transmit packet type' drop down menu and select the 'constant' option. This will transmit a continuous, unmodulated carrier. If you want constant modulated carrier you need to use the radio test example, also found in the SDK.

2. Just configure the spectrum analyzer to use peak detector and trace max hold. It might take some time to 'catch' all of the spectrum and settle, but after some time it will display the same as a continuous carrier.

PS: 6dBm is measured internally in the spectrum analyzer, you need to add what is lost in the cable assembly between the nRF52 PCB and the spectrum analyzer.

Best regards,

Andreas