nRF Programmer 3.6.0 + Segger J-Link Ultra+

RE: nRF Programmer 3.6.0 + Segger J-Link Ultra+

tesc — Thu, 14 Jan 2021 14:28:46 GMT

Hi,

I am sorry for the delays. I am afraid I have not been able to locate an Ultra+.

From the logs, it looks like the issue is not in nRF Connect itself, but in the nrfjprog backend used by nRF Connect. This means the issues might be shared between nRF Connect and nRF Command Line Tools.

Have you attempted to program the board through nrfjprog, which is part of nRF Command Line Tools? In particular with the "--log" option, which saves a more thorough log to a log file named "log.log". Do you experience any problems with that tool as well?

Regards,
Terje

RE: nRF Programmer 3.6.0 + Segger J-Link Ultra+

dhandzic — Fri, 08 Jan 2021 12:12:21 GMT

devzone.nordicsemi.com/.../2021_2D00_01_2D00_08T09_5F00_44_5F00_47.216Z_2D00_log.txt

More log info from todays attempt to update the softmodem on a couple of nRF9160 boards. No other application using Segger Jlink has been started at all after boot up of the PC. I have updated the Jlink to the latest firmware and drivers. Still very unstable with nRF Programmer.

Best regards

Dirk

RE: nRF Programmer 3.6.0 + Segger J-Link Ultra+

dhandzic — Thu, 07 Jan 2021 16:03:06 GMT

Hi Terje,

when trying to connect to the Ultra+ the correct Segger serial number for the device is shown and SES is not running.

Best regards

Dirk

RE: nRF Programmer 3.6.0 + Segger J-Link Ultra+

tesc — Thu, 07 Jan 2021 15:54:49 GMT

Hi,

Thanks. I will try to get hold of a J-Link Ultra+ and reproduce locally.

Before I have done so, I do notice in the log:

2021-01-07T14:07:29.264Z VERBOSE Could not fetch serial number for serial port at COM1
2021-01-07T14:07:29.264Z VERBOSE Could not fetch serial number for serial port at COM25

This is typically what happens when selecting a COM port that is not a J-Link device. Some of the entries in the drop down may be not a J-Link device. Typically you will then also get the error message of "Unsupported device. The detected device could not be recognized as neither JLink device nor Nordic USB device.", which you did not get, but your mileage may vary. I suspect that if there is already a lot of communication over the COM port then you might get the error message that you did instead. Can you double check that the listed COMs are indeed where the J-Link Ultra+ is?

Are there any other applications on the PC also communicating with the J-Link programmer? E.g. open instances of SES, or a J-Link application, or other?

Regards,
Terje

RE: nRF Programmer 3.6.0 + Segger J-Link Ultra+

dhandzic — Thu, 07 Jan 2021 14:15:05 GMT

Hi Terje,

it is our board with a nRF9160, Carl Richard Steen Fosse at Nordic has one of our boards. It appears after selecting the Segger from the 'Select Device' button. The Segger JLINK Ultra + is directly connect to the PC USB port.

This is the content of the latest log file:

2021-01-07T14:07:18.237Z INFO Application data folder: C:\Users\Dirk\AppData\Roaming\nrfconnect\pc-nrfconnect-programmer
2021-01-07T14:07:18.656Z DEBUG App pc-nrfconnect-programmer v1.4.8 official
2021-01-07T14:07:18.656Z DEBUG App path: C:\Users\Dirk\.nrfconnect-apps\node_modules\pc-nrfconnect-programmer
2021-01-07T14:07:18.656Z DEBUG nRFConnect 3.6.1 is supported by the app (^3.6.0)
2021-01-07T14:07:18.656Z DEBUG nRFConnect path: C:\Users\Dirk\AppData\Local\Programs\nrfconnect\resources\app.asar
2021-01-07T14:07:18.656Z DEBUG HomeDir: C:\Users\Dirk
2021-01-07T14:07:18.656Z DEBUG TmpDir: C:\Users\Dirk\AppData\Local\Temp
2021-01-07T14:07:18.683Z INFO Using nrfjprog library 10.12.1, pc-nrfjprog-js 1.7.6
2021-01-07T14:07:29.264Z VERBOSE Could not fetch serial number for serial port at COM1
2021-01-07T14:07:29.264Z VERBOSE Could not fetch serial number for serial port at COM25
2021-01-07T14:07:40.489Z INFO Generating system report...
2021-01-07T14:08:04.924Z INFO Using nrfjprog to communicate with target
2021-01-07T14:08:05.818Z INFO Using J-Link Software version 6.88
2021-01-07T14:08:08.917Z INFO Generating system report...
2021-01-07T14:08:16.277Z ERROR Error when getting device info: Error: Error: Error occured when get probe info. Errorcode: Could not execute the function due to too many calls in line (0xe)

2021-01-07T14:08:16.278Z ERROR Could not fetch memory size of target devkit: Cannot read property 'family' of undefined

Best regards

Dirk

RE: nRF Programmer 3.6.0 + Segger J-Link Ultra+

tesc — Thu, 07 Jan 2021 13:45:50 GMT

Hi,

What SoC? (I assume that the board is your design.)
Just to confirm: The issue appears when selecting the programmer from the drop-down? (That is, you never get to the point of actually selecting anything to program?) If not that, when does it happen?
Can you provide the full log from nRF Connect? (You can find the log file from the left-most button of the three blue buttons at the top right of the log window.)
How is your USB setup, that is, what kind of USB port, hubs, etc. are involved in your setup?

We might need to see your board files as well, depending on whether or not we can pinpoint the issue from answers to the above.

Regards,
Terje

RE: nRF Programmer 3.6.0 + Segger J-Link Ultra+

dhandzic — Thu, 07 Jan 2021 07:58:21 GMT

I have updated to nRF Connect 3.6.1 and Programmer 1.4.8 and Segger JLINK 6.88 and the problems are back!

Programming the same board from the 1.4.1 Toolchain Manager SES works fine!

RE: nRF Programmer 3.6.0 + Segger J-Link Ultra+

dhandzic — Thu, 19 Nov 2020 08:37:22 GMT

Hi,

I am still 6.86d without any problems. The Nordic Toolchain is a bit unstable and I have just lost functionality of the LTE Link Monitor after updating to 1.1.9. It is also very sensitive in case you are using a VPN. At least during update and installation you have to turn of the VPN (NordVPN in my case) in my experience otherwise it might be a total mess.

Hope that might help!

RE: nRF Programmer 3.6.0 + Segger J-Link Ultra+

chucklink — Thu, 19 Nov 2020 00:31:54 GMT

I have similar problem with V6.84a J-link. Nothing change. The nagware somehow updated the Nordic and now it does not work at all on any of our boards DK boards.

RE: nRF Programmer 3.6.0 + Segger J-Link Ultra+

tesc — Fri, 23 Oct 2020 13:54:10 GMT

Hi,

I am happy to hear that you found a working workaround. It may have been an issue with the particular Segger version, in combination either with our SoC or with the particular programmer.

Regards,
Terje

RE: nRF Programmer 3.6.0 + Segger J-Link Ultra+

dhandzic — Fri, 23 Oct 2020 11:37:54 GMT

I have stepped back to Segger 6.86d and rebooted the computer and now it works 🙂