nRF Connect SDK v1.6.1
HW - nRF 52832 DK
Host OS - Ubuntu 18.04 LTS
SES IDE Nordic Edition v5.60 with Segger J-Link USB
If I build the Peripheral UART example then RTT debug logging in SES IDE terminal works. When I add the MCUBOOT Bootloader to the project to add MCUMgr DFU then
the RTT logging stops in the SES IDE terminal.
Below are my proj.conf settings: Setting CONFIG_BOOTLOADER_MCUBOOT=y is what causes the RTT debug logging in SES to stop working. What additional proj.conf settings
do I require for RTT logging to work in IDE ?
# FW version
CONFIG_MCUBOOT_IMAGE_VERSION="0.9.1"
# Enable the UART driver
CONFIG_UART_ASYNC_API=y
CONFIG_NRFX_UARTE0=y
CONFIG_SERIAL=y
CONFIG_GPIO=y
CONFIG_BT=y
CONFIG_BT_PERIPHERAL=y
CONFIG_BT_DEVICE_NAME="Diversey_UART_DFU"
CONFIG_BT_DEVICE_APPEARANCE=833
CONFIG_BT_MAX_CONN=1
CONFIG_BT_MAX_PAIRED=1
# Enable the NUS service
CONFIG_BT_NUS=y
# Enable bonding
CONFIG_BT_SETTINGS=y
CONFIG_FLASH=y
CONFIG_FLASH_PAGE_LAYOUT=y
CONFIG_FLASH_MAP=y
CONFIG_NVS=y
CONFIG_SETTINGS=y
# Enable DK LED and Buttons library
CONFIG_DK_LIBRARY=y
# Enable and Config logger
CONFIG_LOG=y
# Make sure printk is not printing to the UART console
CONFIG_CONSOLE=y
CONFIG_UART_CONSOLE=n
CONFIG_LOG_PRINTK=n
# Enable Segger J-Link RTT debug terminal in SES IDE
CONFIG_USE_SEGGER_RTT=y
CONFIG_RTT_CONSOLE=y
CONFIG_LOG_BACKEND_RTT=y
CONFIG_LOG_BACKEND_UART=n
CONFIG_LOG_DEFAULT_LEVEL=4
CONFIG_ASSERT=y
# added for FOTA
# Must enable MCUBOOT bootloader for DFU to work else mobile error message Invalid Response:{"images":{}, "splitStatus":0}
# Must use split images to swap images out when upload of image completes
CONFIG_BOOTLOADER_MCUBOOT=y # Adding MCUBOOT bootloader CONFIG_BOOTLOADER_MCUBOOT=y stops RTT debug terminal output in IDE terminal
CONFIG_MCUMGR=y
CONFIG_MCUMGR_CMD_OS_MGMT=y
CONFIG_MCUMGR_CMD_IMG_MGMT=y
CONFIG_MCUMGR_SMP_BT=y
CONFIG_MCUMGR_SMP_BT_AUTHEN=n # n=disables the pairing requirement with mobile device
CONFIG_IMG_ERASE_PROGRESSIVELY=y
# Increase the MTU size for DFU
# CONFIG_BT_BUF_ACL_RX_SIZE=251
# CONFIG_BT_BUF_ACL_TX_SIZE=251
# CONFIG_BT_L2CAP_TX_MTU=247
# CONFIG_BT_CTLR_DATA_LENGTH_MAX=251
# Increase the MTU size and Data Len params for faster DFU
CONFIG_BT_BUF_ACL_RX_SIZE=251
CONFIG_BT_GATT_CLIENT=y
CONFIG_BT_ATT_PREPARE_COUNT=2
CONFIG_BT_CONN_TX_MAX=10
CONFIG_BT_L2CAP_TX_BUF_COUNT=10
CONFIG_BT_L2CAP_TX_MTU=247
CONFIG_BT_L2CAP_DYNAMIC_CHANNEL=y
CONFIG_BT_CTLR_PHY_2M=y
CONFIG_BT_CTLR_RX_BUFFERS=2
CONFIG_BT_BUF_ACL_TX_COUNT=10
CONFIG_BT_BUF_ACL_TX_SIZE=251
CONFIG_BT_CTLR_DATA_LENGTH_MAX=251
CONFIG_BT_THROUGHPUT=y
CONFIG_BT_GATT_DM=y
CONFIG_BT_USER_DATA_LEN_UPDATE=y
CONFIG_BT_USER_PHY_UPDATE=y
CONFIG_BT_GAP_AUTO_UPDATE_CONN_PARAMS=n
# Diversey increased from 2048 to 4096 for MCUMgr DFU
CONFIG_HEAP_MEM_POOL_SIZE=4096
