nRF Connect Programmer gives LIBUSB ERROR NO DEVICE

RE: nRF Connect Programmer gives LIBUSB ERROR NO DEVICE

ovrebekk — Mon, 08 Nov 2021 10:41:22 GMT

Hi Brian

It is good to hear that the USBD_POWER_DETECTION setting solved the issue 🙂

As for the additional power consumption this should be negligible when the CPU is running, but in sleep mode it could make an impact (where you might otherwise see a couple of microamps you will now see hundreds of microamps).

Best regards
Torbjørn

RE: nRF Connect Programmer gives LIBUSB ERROR NO DEVICE

brianreinhold — Fri, 05 Nov 2021 08:29:44 GMT

According to my workmate, the setting of the USBD_POWER_DETECTION to false solves the problem. I do not think this will be a problem in production as the dongle will most likely be externally powered by a phone charger or the like.

RE: nRF Connect Programmer gives LIBUSB ERROR NO DEVICE

brianreinhold — Thu, 04 Nov 2021 13:27:35 GMT

Okay, that's good to know. I am unable to reproduce the condition myself I will have to send it to my coworker for testing. But in our use case it does not appear to be an issue as the dongle is meant to be plugged into something like a USB phone charger in the same room as the stationary bike. Power will always be supplied - no batteries involved.

If we ever have a need for a battery version, we can address the problem then. Not sure how much extra power we are really talking about anyways. Sometimes it seems we make mountains out of power issues which are trivial compared to the other concomitant operations.

RE: nRF Connect Programmer gives LIBUSB ERROR NO DEVICE

ovrebekk — Thu, 04 Nov 2021 13:21:00 GMT

Hi Brian

The consequence of setting this to false is that the USB driver will start up even if nothing is connected to the USB bus. The only practical implication of this is that you might waste some power whenever nothing is connected to the bus.

In the dongle use case this should not be relevant, since the system is not running unless the USB is connected.

Best regards
Torbjørn

RE: nRF Connect Programmer gives LIBUSB ERROR NO DEVICE

brianreinhold — Wed, 03 Nov 2021 13:04:56 GMT

Yes that is possible. What are the consequences of having that option set to true or false? It is currently set to true.

RE: nRF Connect Programmer gives LIBUSB ERROR NO DEVICE

ovrebekk — Wed, 03 Nov 2021 12:56:04 GMT

Hi Brian

I am thinking there could be an issue if the USB power up event happens before the application has had the time to start, in which case the USB driver would not get properly initialized during boot.

In order to test this it is possible to disable the USB power up detection by setting the USBD_POWER_DETECTION define in sdk_config.h to false.

Are you able to change this in your application and see if it solves the issue?

Best regards
Torbjørn

RE: nRF Connect Programmer gives LIBUSB ERROR NO DEVICE

brianreinhold — Wed, 03 Nov 2021 08:32:50 GMT

Well, it worked on my system. But on someone else's system a different error occurred. He could plug in the dongle and program it using the nRF Connect Programmer but after a reset, if he tried to repeat the process, he would get a DFU header error. Power cycling the dongle (re-inserting it) would fix the problem and the dongle could be programmed again. But he could not re-program the dongle without re-inserting it first. The same error happened every time.

The repeatable error message was:

2021-11-02T20:45:16.655Z ERROR Error when calling version command: Error: Error message: Response from DFU target did not start with 0x60
2021-11-02T20:45:16.655Z ERROR Error when fetching device versions: TypeError: Cannot read property 'part' of undefined

Here is his full log (there is more than one attempt).

2021-11-02T20:21:55.365Z INFO Application data folder: C:\Users\Ben\AppData\Roaming\nrfconnect\pc-nrfconnect-programmer
2021-11-02T20:21:55.513Z DEBUG App pc-nrfconnect-programmer v1.4.11 official
2021-11-02T20:21:55.513Z DEBUG App path: C:\Users\Ben\.nrfconnect-apps\node_modules\pc-nrfconnect-programmer
2021-11-02T20:21:55.513Z DEBUG nRFConnect 3.7.1, required by the app is (^3.6.0)
2021-11-02T20:21:55.514Z DEBUG nRFConnect path: C:\Users\Ben\AppData\Local\Programs\nrfconnect\resources\app.asar
2021-11-02T20:21:55.514Z DEBUG HomeDir: C:\Users\Ben
2021-11-02T20:21:55.514Z DEBUG TmpDir: C:\Users\Ben\AppData\Local\Temp
2021-11-02T20:21:55.537Z INFO Using nrfjprog library 10.12.1, pc-nrfjprog-js 1.7.6
2021-11-02T20:21:56.556Z VERBOSE Could not fetch serial number for serial port at COM1
2021-11-02T20:22:00.366Z INFO DFU trigger interface found, changing to bootloader...
2021-11-02T20:22:10.427Z ERROR Timeout while waiting for device  F7C5955273A6 to be attached and enumerated
2021-11-02T20:22:10.427Z INFO Target device closed.
2021-11-02T20:22:13.710Z INFO Using USB SDFU protocol to communicate with target
2021-11-02T20:22:13.718Z ERROR Error when calling version command: Error: Opening COM6: File not found
2021-11-02T20:22:13.719Z ERROR Error when fetching device versions: TypeError: Cannot read property 'part' of undefined
2021-11-02T20:22:13.719Z ERROR Error when closing serial port: Error: Port is not open
2021-11-02T20:22:56.630Z INFO Parsing HEX file:  C:\Users\Ben\Downloads\nrf52840_xxaa(3).hex
2021-11-02T20:22:56.653Z INFO File was last modified at  11/2/2021, 4:22:32 PM
2021-11-02T20:23:00.349Z INFO Parsing HEX file:  C:\Users\Ben\Downloads\s140_nrf52_7.2.0_softdevice(3).hex
2021-11-02T20:23:00.350Z INFO File was last modified at  11/2/2021, 4:22:40 PM
2021-11-02T20:23:00.493Z INFO SoftDevice detected, id 0x100 (S140 v7.2.0)
2021-11-02T20:23:07.291Z INFO Using USB SDFU protocol to communicate with target
2021-11-02T20:23:07.304Z INFO Protocol Version:  1 found
2021-11-02T20:23:07.308Z INFO Hardware: 52840 found
2021-11-02T20:23:07.313Z INFO Firmware: Bootloader found
2021-11-02T20:23:07.314Z INFO Firmware: SoftDevice found
2021-11-02T20:23:07.314Z INFO Firmware: Application found
2021-11-02T20:23:07.321Z INFO SoftDevice detected, id 0x100 (S140 v7.2.0)
2021-11-02T20:23:32.373Z INFO Does not need to be reloaded:  C:\Users\Ben\Downloads\nrf52840_xxaa(3).hex
2021-11-02T20:23:32.374Z INFO Does not need to be reloaded:  C:\Users\Ben\Downloads\s140_nrf52_7.2.0_softdevice(3).hex
2021-11-02T20:23:32.378Z INFO SdReq for SoftDevice is set as 0x00.
2021-11-02T20:23:32.380Z INFO Hash is generated by SHA256
2021-11-02T20:23:32.380Z INFO Hash is generated by SHA256
2021-11-02T20:23:32.384Z INFO Performing DFU. This may take a few seconds
2021-11-02T20:23:32.410Z INFO DFU procedure starts. This may take a few seconds.
2021-11-02T20:23:40.900Z INFO DFU for SoftDevice completed successfully!
2021-11-02T20:23:40.901Z INFO 1 dfu package(s) left.
2021-11-02T20:23:40.901Z INFO Waiting for device
2021-11-02T20:23:40.906Z INFO DFU procedure starts. This may take a few seconds.
2021-11-02T20:23:44.248Z INFO DFU for Application completed successfully!
2021-11-02T20:23:44.248Z INFO 0 dfu package(s) left.
2021-11-02T20:23:44.248Z INFO Waiting for device
2021-11-02T20:23:45.256Z INFO All dfu images have been written to the target device.
2021-11-02T20:23:45.257Z INFO DFU trigger interface found, changing to bootloader...
2021-11-02T20:23:45.808Z INFO Using USB SDFU protocol to communicate with target
2021-11-02T20:23:45.821Z INFO Protocol Version:  1 found
2021-11-02T20:23:45.824Z INFO Hardware: 52840 found
2021-11-02T20:23:45.829Z INFO Firmware: Bootloader found
2021-11-02T20:23:45.830Z INFO Firmware: SoftDevice found
2021-11-02T20:23:45.830Z INFO Firmware: Application found
2021-11-02T20:23:45.838Z INFO SoftDevice detected, id 0x100 (S140 v7.2.0)
2021-11-02T20:24:08.781Z INFO Target device closed.
2021-11-02T20:33:46.761Z INFO Using USB SDFU protocol to communicate with target
2021-11-02T20:33:46.791Z ERROR Error when calling version command: Error: Error message: Response from DFU target did not start with 0x60
2021-11-02T20:33:46.792Z ERROR Error when fetching device versions: TypeError: Cannot read property 'part' of undefined
2021-11-02T20:33:54.899Z INFO Using USB SDFU protocol to communicate with target
2021-11-02T20:33:54.911Z ERROR Error when calling version command: Error: Error message: Response from DFU target did not start with 0x60
2021-11-02T20:33:54.911Z ERROR Error when fetching device versions: TypeError: Cannot read property 'part' of undefined
2021-11-02T20:37:24.335Z INFO Using USB SDFU protocol to communicate with target
2021-11-02T20:37:24.349Z ERROR Error when calling version command: Error: Error message: Response from DFU target did not start with 0x60
2021-11-02T20:37:24.349Z ERROR Error when fetching device versions: TypeError: Cannot read property 'part' of undefined
2021-11-02T20:37:53.866Z INFO Target device closed.
2021-11-02T20:38:04.808Z INFO DFU trigger interface found, changing to bootloader...
2021-11-02T20:38:05.350Z INFO Using USB SDFU protocol to communicate with target
2021-11-02T20:38:05.361Z INFO Protocol Version:  1 found
2021-11-02T20:38:05.363Z INFO Hardware: 52840 found
2021-11-02T20:38:05.368Z INFO Firmware: Bootloader found
2021-11-02T20:38:05.368Z INFO Firmware: SoftDevice found
2021-11-02T20:38:05.368Z INFO Firmware: Application found
2021-11-02T20:38:05.372Z INFO SoftDevice detected, id 0x100 (S140 v7.2.0)
2021-11-02T20:38:06.153Z INFO Target device closed.
2021-11-02T20:38:13.195Z INFO Using USB SDFU protocol to communicate with target
2021-11-02T20:38:13.208Z INFO Protocol Version:  1 found
2021-11-02T20:38:13.210Z INFO Hardware: 52840 found
2021-11-02T20:38:13.215Z INFO Firmware: Bootloader found
2021-11-02T20:38:13.215Z INFO Firmware: SoftDevice found
2021-11-02T20:38:13.215Z INFO Firmware: Application found
2021-11-02T20:38:13.218Z INFO SoftDevice detected, id 0x100 (S140 v7.2.0)
2021-11-02T20:44:49.373Z INFO Does not need to be reloaded:  C:\Users\Ben\Downloads\nrf52840_xxaa(3).hex
2021-11-02T20:44:49.374Z INFO Does not need to be reloaded:  C:\Users\Ben\Downloads\s140_nrf52_7.2.0_softdevice(3).hex
2021-11-02T20:44:49.375Z INFO SdReq for SoftDevice is set as 0x00.
2021-11-02T20:44:49.376Z INFO Hash is generated by SHA256
2021-11-02T20:44:49.376Z INFO Hash is generated by SHA256
2021-11-02T20:44:49.381Z INFO Performing DFU. This may take a few seconds
2021-11-02T20:44:49.390Z INFO DFU procedure starts. This may take a few seconds.
2021-11-02T20:44:57.885Z INFO DFU for SoftDevice completed successfully!
2021-11-02T20:44:57.885Z INFO 1 dfu package(s) left.
2021-11-02T20:44:57.886Z INFO Waiting for device
2021-11-02T20:44:57.889Z INFO DFU procedure starts. This may take a few seconds.
2021-11-02T20:45:01.239Z INFO DFU for Application completed successfully!
2021-11-02T20:45:01.239Z INFO 0 dfu package(s) left.
2021-11-02T20:45:01.239Z INFO Waiting for device
2021-11-02T20:45:02.244Z INFO All dfu images have been written to the target device.
2021-11-02T20:45:02.245Z INFO DFU trigger interface found, changing to bootloader...
2021-11-02T20:45:02.784Z INFO Using USB SDFU protocol to communicate with target
2021-11-02T20:45:02.796Z INFO Protocol Version:  1 found
2021-11-02T20:45:02.798Z INFO Hardware: 52840 found
2021-11-02T20:45:02.802Z INFO Firmware: Bootloader found
2021-11-02T20:45:02.803Z INFO Firmware: SoftDevice found
2021-11-02T20:45:02.803Z INFO Firmware: Application found
2021-11-02T20:45:02.808Z INFO SoftDevice detected, id 0x100 (S140 v7.2.0)
2021-11-02T20:45:11.595Z INFO Target device closed.
2021-11-02T20:45:16.643Z INFO Using USB SDFU protocol to communicate with target
2021-11-02T20:45:16.655Z ERROR Error when calling version command: Error: Error message: Response from DFU target did not start with 0x60
2021-11-02T20:45:16.655Z ERROR Error when fetching device versions: TypeError: Cannot read property 'part' of undefined

RE: nRF Connect Programmer gives LIBUSB ERROR NO DEVICE

Jay Tyzzer — Tue, 02 Nov 2021 16:26:20 GMT

Hi Brian,

This is just a follow up to you on the emails we shared. Please close out this ticket if you are satisfied with the answer.

Thanks!

"To be clear, you clicked on USB Nordic Semiconductor nRF52 Connectivity and got that error?

What utility were you attempting to use? Can you try the RSSI utility in nRFconnect?

If that does not work, please reinstall the nRFconnect for desktop. Either the one you have been using or the newest one. Not just a update but a fresh install.

You may get a message asking you if you want to install the USB CDC ACM driver. You want to answer yes.

The Win 10 System / ports should now see the following.

Please let me know if this works for you or not."

Good luck on your project!!

Best regards,

Jay Tyzzer | Sr. Field Application Engineer