Questions regarding CONEVAL

RE: Questions regarding CONEVAL

ced27 — Sat, 20 Nov 2021 11:29:08 GMT

[quote userid="77062" url="~/f/nordic-q-a/81789/questions-regarding-coneval/339755#339755"]But isn't that what the CONEVAL command does?[/quote]

sure Oyvind, which then brings up the question: how does each values from the command CONEVAL affect the energy consumption of the board?

Sorry for the late reply.

Best regards,

Cedric

RE: Questions regarding CONEVAL

Øyvind — Fri, 19 Nov 2021 08:17:06 GMT

But isn't that what the CONEVAL command does?
"The Nordic-proprietary %CONEVAL command requests an evaluation of the LTE radio signal state and an estimation of the energy efficiency in a cell that the modem would use for data transmission. The information can be used to determine the energy efficiency of data transmission before actual data transmission is started. The %CONEVAL command is the most useful for a static or slow-moving device."

<energy_estimate>Relative estimated energy consumption of data transmission compared to nominal consumption. A higher value means smaller energy consumption.

5 – Bad conditions. Difficulties in setting up connections. Maximum number of repetitions might be needed for data.

6 – Poor conditions. Setting up a connection might require retries and a higher number of repetitions for data.

7 – Normal conditions for cIoT device. No repetitions for data or only a few repetitions in the worst case.

8 – Good conditions. Possibly very good conditions for small amounts of data.

9 – Excellent conditions. Efficient data transfer estimated also for larger amounts of data.

RE: Questions regarding CONEVAL

ced27 — Thu, 18 Nov 2021 12:54:41 GMT

[quote userid="77062" url="~/f/nordic-q-a/81789/questions-regarding-coneval/339637#339637"]What are your intensions of the %CONEVAL usage? [/quote]

I want to use the values from %CONEVAL to determine the energy efficiency/ energy consumption estimation of data transmission before actual data transmission has started

Is it possible?

RE: Questions regarding CONEVAL

Øyvind — Thu, 18 Nov 2021 12:40:28 GMT

It's a little more complicated describing the values provided by network and the results of %CONEVAL.

What are your intensions of the %CONEVAL usage?

Please have a look at the following webinars:

And then have a look at our Online Power Profiler for nRF91

Kind regards,
Øyvind

RE: Questions regarding CONEVAL

ced27 — Thu, 18 Nov 2021 11:48:30 GMT

Hi Oyvind,

thanks once again for your response.

I made a table of the variables, whose values are likely to change, when the AT command %CONEVAL is been used periodically.

Can you please take a look at the table and help me out? I will really appreciate

devzone.nordicsemi.com/.../Energy-consumption.xlsx

Best regards,

Cedric

RE: Questions regarding CONEVAL

Øyvind — Thu, 18 Nov 2021 08:30:04 GMT

Higher TX power increases the energy consumption. The same goes for low signal strength.

-Øyvind

RE: Questions regarding CONEVAL

ced27 — Wed, 17 Nov 2021 15:03:47 GMT

Hi Oyvind,

thanks for your respond.

[quote userid="77062" url="~/f/nordic-q-a/81789/questions-regarding-coneval/339452#339452"]There are many variables that impacts the current consumption e.g. TX power, signal strength, among others.[/quote]

And in what ways do they affect the energy consumption or what correlation do they have with the energy consumption?

For example if the value of tx_power increase what happen to the energy consumption, does it increase or decrease?

Best regards,

Cedric

RE: Questions regarding CONEVAL

Øyvind — Wed, 17 Nov 2021 13:42:18 GMT

Hi Cedric,

[quote user=""]Which of these values can i manually affect?[/quote]

None, of these can be affected by application. Most of the values in the %CONEVAL are network supplied, and RSRP, RSPQ and SNR are calculated in modem based on provided values.

[quote user=""]5. How do they affect the current consumption of the device (nrf9160 DK)?[/quote]

There are many variables that impacts the current consumption e.g. TX power, signal strength, among others.

I'm afraid based on these answers your other questions are no longer valid.

Kind regards,
Øyvind