Zephyr PWM and GPIO in System Off

RE: Zephyr PWM and GPIO in System Off

Airat — Fri, 16 Dec 2022 16:58:11 GMT

Thank you, that did what I wanted.

To note GPIO must be configured to output after locking the PWM device, as it sets the PIN_CNF to the default state (0x20).

RE: Zephyr PWM and GPIO in System Off

Sigurd — Fri, 16 Dec 2022 15:48:11 GMT

Hi,

Looks like it's the device driver Power Management implementation that sets the pin to this state as part of the process of going into System Off mode. I haven't tested it, but something like this might work to avoid that:

1) ret = pm_device_action_run(pwm, PM_DEVICE_ACTION_SUSPEND); // unit the PWM
2) ret = pm_device_state_lock(pwm); // Lock the PWM DEVICE

3) Use GPIO API to set the pin as you like

4) Enter system off mode

RE: Zephyr PWM and GPIO in System Off

Airat — Fri, 16 Dec 2022 13:31:09 GMT

Yes, exactly. I need an option for choosing LED to be on or off in System Off mode in a run-time.

RE: Zephyr PWM and GPIO in System Off

Sigurd — Fri, 16 Dec 2022 13:29:07 GMT

[quote user="Airat"]

Interestingly, if I add nordic,invert; to pwm0_sleep then the LED is always off in System Off mode.

Is there a way to control that behavior just before going to System Off? Or will I need to drop usage of the Zephyr PWM driver?

[/quote]

So it's not enough to set the desired level with/without nordic,invert; to pwm0_sleep ? You want to change it based on something at run-time?

RE: Zephyr PWM and GPIO in System Off

Airat — Thu, 15 Dec 2022 21:21:34 GMT

Including PWM driver by CONFIG_PWM=y seems to force the GPIO pin to be configured to OUTPUT with low level (regardless if it's active high or low). And it matches with the requirements from documentation on the PWM peripheral https://infocenter.nordicsemi.com/index.jsp?topic=%2Fps_nrf52840%2Fpwm.html&cp=4_0_0_5_16_3&anchor=concept_ckf_5qw_nr

It looks like the device sets the GPIO pin to 0 before going to System Off.

Interestingly, if I add nordic,invert; to pwm0_sleep then the LED is always off in System Off mode.

Is there a way to control that behavior just before going to System Off? Or will I need to drop usage of the Zephyr PWM driver?

RE: Zephyr PWM and GPIO in System Of

Airat — Thu, 15 Dec 2022 19:27:02 GMT

I have found a way to make it work.

I have removed the low-power-enable; from the pwm0_sleep pin configuration node. And I did not use gpio driver api to set constant active level on the pin. Setting the pulse equal to the period with pwm driver api sets the relevant gpio out to the active level.

EDIT: Unfortunately, it is not completely solved. I cannot control whether GPIO pin should be active or inactive when the device goes to System Off. Regardless of the GPIO OUT values or previous PWM pulse configuration (to 0 or to period) the pin will be active in System Off.

Any advice on how to control it?

RE: Zephyr PWM and GPIO in System Of

Airat — Thu, 15 Dec 2022 14:56:17 GMT

I tried and it didn't work. The LED still went off after going system off. And 1 is is still in the NRF_PWM0->ENABLE.

The ways I found to keep the LED on in system off is to assign different pin for pwm0_sleep pinctrl, but it is not a viable option for my project, as I use all gpio pins and I don't want to cause a problem with strange pin assignments.

Just to clarify, calling gpio_pin_set_dt() does make LED go brighter, so constant level can be set with gpio api. But LED is not kept on in system off.

RE: Zephyr PWM and GPIO in System Of

Sigurd — Thu, 15 Dec 2022 14:27:55 GMT

Hi,

Try setting NRF_PWM0->PSEL.OUT[0] to 0xFFFFFFFF , before you configure the GPIO as output and set it to the desired level.

RE: Zephyr PWM and GPIO in System Of

Airat — Thu, 15 Dec 2022 13:32:55 GMT

I can check register values before, and after setting the GPIO pin

NRF_PWM0->ENABLE: 0x00000001
NRF_PWM0->PSEL.OUT[0]: 0x0000000E
NRF_GPIO->PIN_CNF[14]: 0x00000003
NRF_GPIO->OUTSET: 0x00004060
GPIO P0.14 set: 1
NRF_PWM0->ENABLE: 0x00000001
NRF_PWM0->PSEL.OUT[0]: 0x0000000E
NRF_GPIO->PIN_CNF[14]: 0x00000003
NRF_GPIO->OUTSET: 0x00000060

Yes the GPIO pin 14 is set to active level.

RE: Zephyr PWM and GPIO in System Of

Sigurd — Thu, 15 Dec 2022 12:51:00 GMT

Hi,

[quote user=""]I tried setting the line to constant inactive with the Zephyr PWM driver by setting the pulse equal to 0 and then setting the active level with the GPIO driver.[/quote]

In this case, did you check that the GPIO was at the correct level before system off?