nRF9160 SLM data mode exit

RE: nRF9160 SLM data mode exit

Øyvind — Thu, 12 Jan 2023 09:06:43 GMT

Hello,
are you able to share more information on the MQTT payload? I would like to reproduce the issue on my side, but will need more information on your setup on both modem side and host side please.

Thanks

Kind regards,
Øyvind

RE: nRF9160 SLM data mode exit

yesheng — Tue, 10 Jan 2023 08:22:21 GMT

Hi Øyvind,

I think 2.0.2 doesn't send this. Instead, it sends "OK" when the modem sent the message successfully.

However, I'm still a bit confused about how to utilize #XDATAMODE:0. Do I keep sending "+++" every now and then until the modem returns "#XDATAMODE: 0"? This approach seems a bit ineffective.

Thanks,

RE: nRF9160 SLM data mode exit

Øyvind — Tue, 10 Jan 2023 08:03:25 GMT

Do you receive "#XDATAMODE: 0"? According to our developers you must wait for this, and refer to the latest version of the SLM documentation on Exiting data mode.

RE: nRF9160 SLM data mode exit

yesheng — Thu, 05 Jan 2023 07:51:55 GMT

Hi Øyvind,

I'm using AT#XMQTTPUB to enter data mode, the payload comes after this. The payload ends with "+++", which tells the modem to leave the data mode.

Once the modem is stuck in the data mode, the next AT#XMQTTPUB will be treated as part of the payload. Hence, I can see the "+++AT#XMQTTPUB" in the MQTT broker.

My hypothesis is the modem for some reason stuck in "datamode off pending" state for a little longer. Hence, the modem still sends everything it receives until it actually leaves the datamode.

RE: nRF9160 SLM data mode exit

Øyvind — Thu, 05 Jan 2023 07:37:18 GMT

Thanks for clarifying. Sorry for the late answer.

Can you provide the commands that you send from the host MCU to the SLM device? What signal does your state machine receive from the SLM?

RE: nRF9160 SLM data mode exit

yesheng — Sun, 01 Jan 2023 14:15:11 GMT

Sorry I wasn't clear. I was referring to the state machine in the host MCU. The state machine thinks the 9160 exits the data mode and starts sending some AT commands. However, those AT commands were sent to the MQTT broker.

I'm using the out-of-the-box SLM FW.

RE: nRF9160 SLM data mode exit

Øyvind — Fri, 30 Dec 2022 09:55:50 GMT

[quote user="yesheng"]This confuses my state machine, so part of the command was treated as data and being sent.[/quote]

Have you added this state machine to the Serial LTE Modem application? If so, can you share what this does and where it does?

RE: nRF9160 SLM data mode exit

yesheng — Thu, 29 Dec 2022 08:45:07 GMT

Hi Øyvind,

Thanks for the suggestion. Under normal conditions, the modem should do the following:

Enters data mode --> sends ABC bytes --> sends XYZ bytes --> exits data mode (by appending "+++" at the end of sending XYZ bytes).

The RTT viewer for normal conditions looks like this:

However, the "+++" doesn't always work immediately. The abnormal conditions look like this:

Enter data mode --> sends ABC bytes --> sends XYZ bytes (with "+++" appended in the end) --> sends QRS bytes --> exits data mode. Although the modem receives the "+++" at the end of XYZ bytes, it doesn't actually exit the data mode until QRS was sent.

From this capture, the modem receives "+++" symbol at time 00:14:57.111,145, but didn't exit data mode until the next blob was sent 00:14:58.559,844.

This confuses my state machine, so part of the command was treated as data and being sent.

Any suggestions?

Thanks!

RE: nRF9160 SLM data mode exit

Øyvind — Wed, 28 Dec 2022 11:40:31 GMT

Hello, are you getting any errors in RTT or log output?

Kind regards,
Øyvind

RE: nRF9160 SLM data mode exit

Øyvind — Wed, 28 Dec 2022 08:54:20 GMT

Hello,

Due to Christmas Holidays our team is lower staffed than normal and some delays in our answers must be expected. We apologize for the inconvenience.

I will have a look at your ticket and get back to within today or tomorrow.

Kind regards,
Øyvind