MCUBoot SPI Flash Image

RE: MCUBoot SPI Flash Image

Håkon Alseth — Wed, 11 Jan 2023 14:00:17 GMT

Hi,

I do not have this specific flash device, but I tried setting up the nRF52840 in spi mode with the mx25r64, and it booted without errors.

Q1: Have you scoped the SPI pins to see if there's something strange happening during the bootup in mcuboot?

Q2: Have you tried moving your changes to a minimal project, like hello_world, to see if the same issue happens there?

Kind regards,

Håkon

RE: MCUBoot SPI Flash Image

ksuaning — Tue, 10 Jan 2023 00:59:51 GMT

Hello,

I disabled spi1 & spi2 in mcuboot and preformed a clean build unfortunately no change in the output.

The external flash is powered by a supply independent of the microcontroller. Other GPIO are in use for some sensors but these have been disabled while I debug this issue.

Thanks,

Kaj

RE: MCUBoot SPI Flash Image

Håkon Alseth — Mon, 09 Jan 2023 15:00:52 GMT

Hi,

When changing the DT or adding child-image files, it is very important that you fully re-generate the build (ie. delete the build folder).

This is to ensure that the build is picking up newly created files.

I see from the .config, that you have several SPI instances enabled in mcuboot:

CONFIG_NRFX_SPI1=y
CONFIG_NRFX_SPI2=y

You can disable these by adding this to the mcuboot board overlay:

&spi1 {
    status = "disabled";
};

&spi2 {
    status = "disabled";
};

These spi instances are configured to use P0.15-P0.17 and P0.25/0.26/0.28.

Is there any other GPIOs that you use, for instance to power up your external flash on your custom board?

Kind regards,

Håkon

RE: MCUBoot SPI Flash Image

ksuaning — Mon, 09 Jan 2023 09:29:34 GMT

Hello,

Setting CONFIG_SPI_NOR_FLASH_LAYOUT_PAGE_SIZE=4096 unfortunately didn't fix the issue.

I extend t-exit-dpd to 70us to match the maximum spec however this didn't seem to resolve the issue.

RE: MCUBoot SPI Flash Image

Håkon Alseth — Mon, 09 Jan 2023 08:55:10 GMT

Hi,

Your flash page size is set to 64K in this config:

CONFIG_SPI_NOR_FLASH_LAYOUT_PAGE_SIZE

Can you try setting this to 4096?

If you still see issues wrt. contacting the device in mcuboot, could you verify the enter/exit DPD timing towards your chosen flash IC?

These are now 35 us and 10 us in your setup:

t-enter-dpd = <10000>;
t-exit-dpd = <35000>;

Kind regards,

Håkon

RE: MCUBoot SPI Flash Image

ksuaning — Mon, 09 Jan 2023 08:19:23 GMT

Thanks so much for the quick response. Here are the relevant files:

.config:

#
# MCUboot-specific configuration options
#
# CONFIG_BOOT_USE_MIN_PARTITION_SIZE is not set
CONFIG_PM_PARTITION_SIZE_MCUBOOT_SCRATCH=0x1e000
CONFIG_PM_PARTITION_SIZE_MCUBOOT_PAD=0x200
CONFIG_PM_PARTITION_SIZE_MCUBOOT=0xc000
CONFIG_MCUBOOT_NRF_CLEANUP_PERIPHERAL=y
CONFIG_BOOT_SIGNATURE_KEY_FILE="root-rsa-2048.pem"
CONFIG_BOOT_ERASE_PROGRESSIVELY=y
# CONFIG_BOOT_IMAGE_ACCESS_HOOKS is not set
CONFIG_MCUBOOT=y
CONFIG_BOOT_USE_MBEDTLS=y
# CONFIG_NRF_CC310_BL is not set

#
# MCUBoot settings
#
# CONFIG_SINGLE_APPLICATION_SLOT is not set
# CONFIG_BOOT_SIGNATURE_TYPE_NONE is not set
CONFIG_BOOT_SIGNATURE_TYPE_RSA=y
CONFIG_BOOT_SIGNATURE_TYPE_RSA_LEN=2048
# CONFIG_BOOT_SIGNATURE_TYPE_ECDSA_P256 is not set
# CONFIG_BOOT_SIGNATURE_TYPE_ED25519 is not set
# CONFIG_MCUBOOT_CLEANUP_ARM_CORE is not set
CONFIG_MBEDTLS_CFG_FILE="mcuboot-mbedtls-cfg.h"
# CONFIG_BOOT_HW_KEY is not set
CONFIG_BOOT_VALIDATE_SLOT0=y
# CONFIG_BOOT_SWAP_USING_SCRATCH is not set
# CONFIG_BOOT_UPGRADE_ONLY is not set
CONFIG_BOOT_SWAP_USING_MOVE=y
# CONFIG_BOOT_DIRECT_XIP is not set
# CONFIG_BOOT_RAM_LOAD is not set
# CONFIG_BOOT_BOOTSTRAP is not set
# CONFIG_BOOT_SWAP_SAVE_ENCTLV is not set
# CONFIG_BOOT_ENCRYPT_RSA is not set
# CONFIG_BOOT_ENCRYPT_EC256 is not set
# CONFIG_BOOT_ENCRYPT_X25519 is not set
CONFIG_BOOT_MAX_IMG_SECTORS=1024
# CONFIG_MEASURED_BOOT is not set
# CONFIG_BOOT_SHARE_DATA is not set
CONFIG_BOOT_FIH_PROFILE_OFF=y
# CONFIG_BOOT_FIH_PROFILE_LOW is not set
# CONFIG_BOOT_FIH_PROFILE_MEDIUM is not set
# CONFIG_BOOT_FIH_PROFILE_HIGH is not set
CONFIG_BOOT_USB_DFU_NO=y
# CONFIG_BOOT_USB_DFU_WAIT is not set
# CONFIG_BOOT_USB_DFU_GPIO is not set
CONFIG_ZEPHYR_TRY_MASS_ERASE=y
# CONFIG_BOOT_USE_BENCH is not set
# CONFIG_MCUBOOT_LOG_LEVEL_OFF is not set
# CONFIG_MCUBOOT_LOG_LEVEL_ERR is not set
# CONFIG_MCUBOOT_LOG_LEVEL_WRN is not set
CONFIG_MCUBOOT_LOG_LEVEL_INF=y
# CONFIG_MCUBOOT_LOG_LEVEL_DBG is not set
CONFIG_MCUBOOT_LOG_LEVEL=3
CONFIG_MCUBOOT_LOG_THREAD_STACK_SIZE=768
# CONFIG_MCUBOOT_INDICATION_LED is not set
# CONFIG_MCUBOOT_SERIAL is not set
# CONFIG_BOOT_INTR_VEC_RELOC is not set
CONFIG_UPDATEABLE_IMAGE_NUMBER=1
CONFIG_BOOT_WATCHDOG_FEED=y
# CONFIG_MCUBOOT_ACTION_HOOKS is not set
# end of MCUBoot settings

CONFIG_MCUBOOT_DEVICE_SETTINGS=y

#
# Zephyr configuration options
#
CONFIG_MULTITHREADING=y
CONFIG_USB_DEVICE_PRODUCT="MCUBOOT"
CONFIG_GPIO=y
CONFIG_SPI=y
# CONFIG_I2C is not set
# CONFIG_KSCAN is not set
# CONFIG_WIFI is not set
# CONFIG_FT800 is not set
CONFIG_GPIO_INIT_PRIORITY=40
# CONFIG_MODEM is not set
CONFIG_UART_INTERRUPT_DRIVEN=y
# CONFIG_SENSOR is not set
CONFIG_BOARD="nrf52dk_nrf52832"
CONFIG_SOC="nRF52832_QFAA"
CONFIG_SOC_SERIES="nrf52"
CONFIG_NUM_IRQS=39
CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC=32768
CONFIG_CLOCK_CONTROL_INIT_PRIORITY=30
CONFIG_FLASH_SIZE=512
CONFIG_FLASH_BASE_ADDRESS=0x0
CONFIG_HEAP_MEM_POOL_SIZE=0
CONFIG_ROM_START_OFFSET=0
CONFIG_PINCTRL=y
# CONFIG_WATCHDOG is not set
CONFIG_SOC_HAS_TIMING_FUNCTIONS=y
CONFIG_ARCH_HAS_CUSTOM_BUSY_WAIT=y
# CONFIG_CORTEX_M_SYSTICK is not set
# CONFIG_PM is not set
# CONFIG_PM_DEVICE is not set
CONFIG_NRF52_ANOMALY_132_WORKAROUND=y
CONFIG_CLOCK_CONTROL=y
CONFIG_NRF_RTC_TIMER=y
CONFIG_SYS_CLOCK_TICKS_PER_SEC=32768
CONFIG_BUILD_OUTPUT_HEX=y
CONFIG_SERIAL_INIT_PRIORITY=55
# CONFIG_FPU is not set
CONFIG_MBEDTLS=y
# CONFIG_CODE_DATA_RELOCATION is not set
# CONFIG_CPU_HAS_CUSTOM_FIXED_SOC_MPU_REGIONS is not set
# CONFIG_TINYCRYPT is not set
CONFIG_SERIAL=y
# CONFIG_SRAM_VECTOR_TABLE is not set
CONFIG_MP_NUM_CPUS=1
CONFIG_PLATFORM_SPECIFIC_INIT=y

#
# Modules
#

#
# Available modules.
#

#
# nrf (F:/nrf_project/joiner_v3/nrf)
#
CONFIG_NUM_METAIRQ_PRIORITIES=0
CONFIG_SYSTEM_WORKQUEUE_STACK_SIZE=1024
CONFIG_MAIN_STACK_SIZE=10240
# CONFIG_INIT_STACKS is not set

#
# Nordic nRF Connect
#
CONFIG_WARN_EXPERIMENTAL=y
CONFIG_PRIVILEGED_STACK_SIZE=1024
# CONFIG_ENTROPY_GENERATOR is not set
CONFIG_INIT_ARCH_HW_AT_BOOT=y
CONFIG_NORDIC_QSPI_NOR_FLASH_LAYOUT_PAGE_SIZE=4096
# CONFIG_NCS_SAMPLES_DEFAULTS is not set
CONFIG_LOG_DEFAULT_LEVEL=4

#
# Image build variants
#
# CONFIG_NCS_IS_VARIANT_IMAGE is not set
CONFIG_NCS_MCUBOOT_IN_BUILD=y
# end of Image build variants

#
# Bootloader
#
# CONFIG_BUILD_S1_VARIANT is not set
# CONFIG_SECURE_BOOT is not set
CONFIG_PM_PARTITION_SIZE_PROVISION=0x1000
# CONFIG_B0_MIN_PARTITION_SIZE is not set
CONFIG_PM_PARTITION_SIZE_B0_IMAGE=0x7000
# CONFIG_SECURE_BOOT_CRYPTO is not set

#
# Secure Boot firmware validation
#
CONFIG_SB_VALIDATION_INFO_MAGIC=0x86518483
CONFIG_SB_VALIDATION_POINTER_MAGIC=0x6919b47e
CONFIG_SB_VALIDATION_INFO_CRYPTO_ID=1
CONFIG_SB_VALIDATION_INFO_VERSION=2
CONFIG_SB_VALIDATION_METADATA_OFFSET=0
CONFIG_SB_VALIDATE_FW_SIGNATURE=y
# end of Secure Boot firmware validation
# end of Bootloader

#
# Bluetooth Low Energy
#

#
# BLE over nRF RPC
#
# end of BLE over nRF RPC
# end of Bluetooth Low Energy

#
# DFU
#
# CONFIG_DFU_MULTI_IMAGE is not set
# CONFIG_DFU_TARGET is not set
# end of DFU

# CONFIG_ESB is not set
# CONFIG_EMDS is not set

#
# Peripheral CPU DFU (PCD)
#
# CONFIG_PCD is not set
# CONFIG_PCD_APP is not set
# CONFIG_PCD_NET is not set
# end of Peripheral CPU DFU (PCD)

#
# Networking
#

#
# Application protocols
#

#
# nRF Cloud
#

#
# Client ID (nRF Cloud Device ID)
#
CONFIG_NRF_CLOUD_CLIENT_ID_SRC_COMPILE_TIME=y
CONFIG_NRF_CLOUD_CLIENT_ID="my-client-id"
# end of Client ID (nRF Cloud Device ID)

# CONFIG_NRF_CLOUD_MQTT is not set
# CONFIG_NRF_CLOUD_FOTA is not set
# CONFIG_NRF_CLOUD_FOTA_FULL_MODEM_UPDATE is not set
# CONFIG_NRF_CLOUD_REST is not set
# CONFIG_NRF_CLOUD_GATEWAY is not set
# CONFIG_NRF_CLOUD_LOG_LEVEL_OFF is not set
# CONFIG_NRF_CLOUD_LOG_LEVEL_ERR is not set
# CONFIG_NRF_CLOUD_LOG_LEVEL_WRN is not set
CONFIG_NRF_CLOUD_LOG_LEVEL_INF=y
# CONFIG_NRF_CLOUD_LOG_LEVEL_DBG is not set
CONFIG_NRF_CLOUD_LOG_LEVEL=3
# end of nRF Cloud

# CONFIG_REST_CLIENT is not set
# CONFIG_DOWNLOAD_CLIENT is not set
# CONFIG_AWS_IOT is not set
# CONFIG_AWS_JOBS is not set
# CONFIG_AZURE_IOT_HUB is not set

#
# Self-Registration (Zi ZHu Ce)
#
# end of Self-Registration (Zi ZHu Ce)

# CONFIG_ICAL_PARSER is not set
# CONFIG_FTP_CLIENT is not set
# CONFIG_LWM2M_CLIENT_UTILS is not set
# end of Application protocols

#
# Link layer options
#
# CONFIG_NET_L2_NRF_WIFI_MGMT is not set
# CONFIG_NET_L2_NRF_WIFI_SHELL is not set
# end of Link layer options
# end of Networking

#
# NFC
#
# CONFIG_NFC_NDEF is not set
# CONFIG_NFC_NDEF_PARSER is not set
# CONFIG_NFC_NDEF_PAYLOAD_TYPE_COMMON is not set
# CONFIG_NFC_T2T_PARSER is not set
# CONFIG_NFC_T4T_NDEF_FILE is not set
# CONFIG_NFC_T4T_ISODEP is not set
# CONFIG_NFC_T4T_APDU is not set
# CONFIG_NFC_T4T_CC_FILE is not set
# CONFIG_NFC_T4T_HL_PROCEDURE is not set
# CONFIG_NFC_PLATFORM is not set
# CONFIG_NFC_TNEP_TAG is not set
# CONFIG_NFC_TNEP_POLLER is not set
# CONFIG_NFC_TNEP_CH is not set
# end of NFC

# CONFIG_APP_EVENT_MANAGER is not set
# CONFIG_NRF_PROFILER is not set

#
# SPM
#
# CONFIG_SPM is not set
# CONFIG_IS_SPM is not set
# end of SPM

# CONFIG_FW_INFO is not set

#
# Debug
#
# CONFIG_PPI_TRACE is not set
# CONFIG_CPU_LOAD is not set
# end of Debug

#
# Nordic MPSL
#
# CONFIG_MPSL_FEM_DEVICE_CONFIG_254 is not set
# CONFIG_MPSL_FEM_LOG_LEVEL_OFF is not set
# CONFIG_MPSL_FEM_LOG_LEVEL_ERR is not set
# CONFIG_MPSL_FEM_LOG_LEVEL_WRN is not set
CONFIG_MPSL_FEM_LOG_LEVEL_INF=y
# CONFIG_MPSL_FEM_LOG_LEVEL_DBG is not set
CONFIG_MPSL_FEM_LOG_LEVEL=3
# CONFIG_MPSL_CX is not set
# CONFIG_MPSL_CX_LOG_LEVEL_OFF is not set
# CONFIG_MPSL_CX_LOG_LEVEL_ERR is not set
# CONFIG_MPSL_CX_LOG_LEVEL_WRN is not set
CONFIG_MPSL_CX_LOG_LEVEL_INF=y
# CONFIG_MPSL_CX_LOG_LEVEL_DBG is not set
CONFIG_MPSL_CX_LOG_LEVEL=3
CONFIG_MPSL_THREAD_COOP_PRIO=8
CONFIG_MPSL_WORK_STACK_SIZE=1024
CONFIG_MPSL_TIMESLOT_SESSION_COUNT=0
# CONFIG_MPSL_ASSERT_HANDLER is not set
# CONFIG_MPSL_LOG_LEVEL_OFF is not set
# CONFIG_MPSL_LOG_LEVEL_ERR is not set
# CONFIG_MPSL_LOG_LEVEL_WRN is not set
CONFIG_MPSL_LOG_LEVEL_INF=y
# CONFIG_MPSL_LOG_LEVEL_DBG is not set
CONFIG_MPSL_LOG_LEVEL=3
# end of Nordic MPSL

# CONFIG_CHIP is not set

#
# Partition Manager
#
CONFIG_PARTITION_MANAGER_ENABLED=y
CONFIG_FLASH_MAP_CUSTOM=y
CONFIG_SRAM_SIZE=64
CONFIG_SRAM_BASE_ADDRESS=0x20000000

#
# Zephyr subsystem configurations
#
# end of Zephyr subsystem configurations

#
# NCS subsystem configurations
#
# CONFIG_PM_SINGLE_IMAGE is not set
CONFIG_PM_EXTERNAL_FLASH_BASE=0
CONFIG_PM_EXTERNAL_FLASH_MCUBOOT_SECONDARY=y
CONFIG_PM_OVERRIDE_EXTERNAL_DRIVER_CHECK=y
CONFIG_PM_SRAM_BASE=0x20000000
CONFIG_PM_SRAM_SIZE=0x10000
# end of Partition Manager

#
# nRF RPC (Remote Procedure Call) library
#
# end of nRF RPC (Remote Procedure Call) library

#
# Full Modem Firmware Update Management(FMFU)
#
# CONFIG_MGMT_FMFU_LOG_LEVEL_OFF is not set
# CONFIG_MGMT_FMFU_LOG_LEVEL_ERR is not set
# CONFIG_MGMT_FMFU_LOG_LEVEL_WRN is not set
CONFIG_MGMT_FMFU_LOG_LEVEL_INF=y
# CONFIG_MGMT_FMFU_LOG_LEVEL_DBG is not set
CONFIG_MGMT_FMFU_LOG_LEVEL=3
# end of Full Modem Firmware Update Management(FMFU)

# CONFIG_CAF is not set

#
# Nordic IEEE 802.15.4
#
# end of Nordic IEEE 802.15.4

# CONFIG_DM_MODULE is not set

#
# Libraries
#

#
# Binary libraries
#
# end of Binary libraries

# CONFIG_ADP536X is not set
# CONFIG_AT_MONITOR is not set
# CONFIG_LTE_LINK_CONTROL is not set
CONFIG_NRF_BPROT_FLASH_REGION_SIZE=0x1000
CONFIG_FPROTECT_BLOCK_SIZE=0x1000
CONFIG_FPROTECT=y
# CONFIG_FPROTECT_APP is not set
# CONFIG_DK_LIBRARY is not set
# CONFIG_MODEM_INFO is not set
CONFIG_RESET_ON_FATAL_ERROR=y
# CONFIG_FATAL_ERROR_LOG_LEVEL_OFF is not set
# CONFIG_FATAL_ERROR_LOG_LEVEL_ERR is not set
# CONFIG_FATAL_ERROR_LOG_LEVEL_WRN is not set
CONFIG_FATAL_ERROR_LOG_LEVEL_INF=y
# CONFIG_FATAL_ERROR_LOG_LEVEL_DBG is not set
CONFIG_FATAL_ERROR_LOG_LEVEL=3
# CONFIG_SMS is not set
# CONFIG_SUPL_CLIENT_LIB is not set
# CONFIG_DATE_TIME is not set
# CONFIG_WAVE_GEN_LIB is not set
CONFIG_HW_UNIQUE_KEY_PARTITION_SIZE=0
# CONFIG_MODEM_JWT is not set
# CONFIG_QOS is not set
# end of Libraries

#
# Device Drivers
#
# CONFIG_BT_DRIVER_QUIRK_NO_AUTO_DLE is not set
# CONFIG_ETH_RTT is not set
# CONFIG_NRF_SW_LPUART is not set
CONFIG_NRFX_GPIOTE_NUM_OF_EVT_HANDLERS=1
# end of Device Drivers

#
# External libraries
#
# end of External libraries

#
# Test
#
CONFIG_ZTEST_MULTICORE_DEFAULT_SETTINGS=y
# CONFIG_UNITY is not set
# end of Test
# end of Nordic nRF Connect

CONFIG_ZEPHYR_NRF_MODULE=y
# end of nrf (F:/nrf_project/joiner_v3/nrf)

#
# hostap (F:/nrf_project/joiner_v3/modules/lib/hostap)
#
CONFIG_ZEPHYR_HOSTAP_MODULE=y
# end of hostap (F:/nrf_project/joiner_v3/modules/lib/hostap)

#
# mcuboot (F:/nrf_project/joiner_v3/bootloader/mcuboot)
#

#
# MCUboot
#
CONFIG_SIGN_IMAGES=y
CONFIG_DT_FLASH_WRITE_BLOCK_SIZE=4
# end of MCUboot

CONFIG_ZEPHYR_MCUBOOT_MODULE=y
# end of mcuboot (F:/nrf_project/joiner_v3/bootloader/mcuboot)

#
# mbedtls (F:/nrf_project/joiner_v3/modules/crypto/mbedtls)
#
CONFIG_ZEPHYR_MBEDTLS_MODULE=y
CONFIG_MBEDTLS_BUILTIN=y
# CONFIG_MBEDTLS_LIBRARY is not set
# CONFIG_CUSTOM_MBEDTLS_CFG_FILE is not set
CONFIG_MBEDTLS_SSL_MAX_CONTENT_LEN=1500
# CONFIG_MBEDTLS_DEBUG is not set
# CONFIG_MBEDTLS_MEMORY_DEBUG is not set
# CONFIG_MBEDTLS_TEST is not set
# CONFIG_MBEDTLS_ENABLE_HEAP is not set
CONFIG_APP_LINK_WITH_MBEDTLS=y

#
# PSA RNG support
#
# CONFIG_PSA_WANT_ALG_CTR_DRBG is not set
# CONFIG_PSA_WANT_ALG_HMAC_DRBG is not set
# end of PSA RNG support

#
# PSA Key support
#
CONFIG_PSA_HAS_KEY_SUPPORT=y
CONFIG_PSA_WANT_KEY_TYPE_DERIVE=y
CONFIG_PSA_WANT_KEY_TYPE_HMAC=y
CONFIG_PSA_WANT_KEY_TYPE_AES=y
CONFIG_PSA_WANT_KEY_TYPE_ARIA=y
CONFIG_PSA_WANT_KEY_TYPE_CHACHA20=y
CONFIG_PSA_WANT_KEY_TYPE_ECC_KEY_PAIR=y
CONFIG_PSA_WANT_KEY_TYPE_ECC_PUBLIC_KEY=y
CONFIG_PSA_WANT_KEY_TYPE_RAW_DATA=y
# end of PSA Key support

#
# PSA AEAD support
#
CONFIG_PSA_HAS_AEAD_SUPPORT=y
CONFIG_PSA_WANT_ALG_CCM=y
CONFIG_PSA_WANT_ALG_GCM=y
CONFIG_PSA_WANT_ALG_CHACHA20_POLY1305=y
# end of PSA AEAD support

#
# PSA Mac support
#
CONFIG_PSA_HAS_MAC_SUPPORT=y
CONFIG_PSA_WANT_ALG_CMAC=y
CONFIG_PSA_WANT_ALG_HMAC=y
# end of PSA Mac support

#
# PSA Hash support
#
CONFIG_PSA_HAS_HASH_SUPPORT=y
CONFIG_PSA_WANT_ALG_SHA_1=y
CONFIG_PSA_WANT_ALG_SHA_224=y
CONFIG_PSA_WANT_ALG_SHA_256=y
CONFIG_PSA_WANT_ALG_SHA_384=y
CONFIG_PSA_WANT_ALG_SHA_512=y
CONFIG_PSA_WANT_ALG_RIPEMD160=y
CONFIG_PSA_WANT_ALG_MD5=y
# end of PSA Hash support

#
# PSA Cipher support
#
CONFIG_PSA_HAS_CIPHER_SUPPORT=y
CONFIG_PSA_WANT_ALG_ECB_NO_PADDING=y
CONFIG_PSA_WANT_ALG_CBC_NO_PADDING=y
CONFIG_PSA_WANT_ALG_CBC_PKCS7=y
CONFIG_PSA_WANT_ALG_CFB=y
CONFIG_PSA_WANT_ALG_CTR=y
CONFIG_PSA_WANT_ALG_OFB=y
# end of PSA Cipher support

#
# PSA Key derivation support
#
CONFIG_PSA_HAS_KEY_DERIVATION=y
CONFIG_PSA_WANT_ALG_HKDF=y
# CONFIG_PSA_WANT_ALG_TLS12_PRF is not set
# CONFIG_PSA_WANT_ALG_TLS12_PSK_TO_MS is not set
# end of PSA Key derivation support

#
# PSA Assymetric support
#
CONFIG_PSA_HAS_ASYM_SIGN_SUPPORT=y
CONFIG_PSA_HAS_ECC_SUPPORT=y
CONFIG_PSA_WANT_ALG_ECDH=y
CONFIG_PSA_WANT_ALG_ECDSA=y
CONFIG_PSA_WANT_ALG_DETERMINISTIC_ECDSA=y

#
# Elliptic Curve type support
#
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_256 is not set
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_384 is not set
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_512 is not set
# CONFIG_PSA_WANT_ECC_MONTGOMERY_255 is not set
# CONFIG_PSA_WANT_ECC_MONTGOMERY_448 is not set
# CONFIG_PSA_WANT_ECC_SECP_K1_192 is not set
# CONFIG_PSA_WANT_ECC_SECP_K1_256 is not set
# CONFIG_PSA_WANT_ECC_SECP_R1_192 is not set
# CONFIG_PSA_WANT_ECC_SECP_R1_224 is not set
CONFIG_PSA_WANT_ECC_SECP_R1_256=y
# CONFIG_PSA_WANT_ECC_SECP_R1_384 is not set
# CONFIG_PSA_WANT_ECC_SECP_R1_521 is not set
# end of Elliptic Curve type support

# CONFIG_PSA_WANT_ALG_RSA_OAEP is not set
# CONFIG_PSA_WANT_ALG_RSA_PKCS1V15_CRYPT is not set
# CONFIG_PSA_WANT_ALG_RSA_PKCS1V15_SIGN is not set
# CONFIG_PSA_WANT_ALG_RSA_PSS is not set
# end of PSA Assymetric support

CONFIG_PSA_WANT_ALG_STREAM_CIPHER=y
# end of mbedtls (F:/nrf_project/joiner_v3/modules/crypto/mbedtls)

#
# trusted-firmware-m (F:/nrf_project/joiner_v3/modules/tee/tf-m/trusted-firmware-m)
#
CONFIG_ZEPHYR_TRUSTED_FIRMWARE_M_MODULE=y
# end of trusted-firmware-m (F:/nrf_project/joiner_v3/modules/tee/tf-m/trusted-firmware-m)

#
# cjson (F:/nrf_project/joiner_v3/modules/lib/cjson)
#
CONFIG_ZEPHYR_CJSON_MODULE=y
# end of cjson (F:/nrf_project/joiner_v3/modules/lib/cjson)

#
# azure-sdk-for-c (F:/nrf_project/joiner_v3/modules/lib/azure-sdk-for-c)
#
# CONFIG_AZURE_SDK is not set
CONFIG_ZEPHYR_AZURE_SDK_FOR_C_MODULE=y
# end of azure-sdk-for-c (F:/nrf_project/joiner_v3/modules/lib/azure-sdk-for-c)

#
# memfault-firmware-sdk (F:/nrf_project/joiner_v3/modules/lib/memfault-firmware-sdk)
#
# CONFIG_MEMFAULT is not set
CONFIG_ZEPHYR_MEMFAULT_FIRMWARE_SDK_MODULE=y
# end of memfault-firmware-sdk (F:/nrf_project/joiner_v3/modules/lib/memfault-firmware-sdk)

#
# cirrus-logic (F:/nrf_project/joiner_v3/modules/hal/cirrus-logic)
#
# CONFIG_HW_CODEC_CIRRUS_LOGIC is not set
CONFIG_ZEPHYR_CIRRUS_LOGIC_MODULE=y
# end of cirrus-logic (F:/nrf_project/joiner_v3/modules/hal/cirrus-logic)

#
# openthread (F:/nrf_project/joiner_v3/modules/lib/openthread)
#
# CONFIG_OPENTHREAD is not set
CONFIG_ZEPHYR_OPENTHREAD_MODULE=y
# end of openthread (F:/nrf_project/joiner_v3/modules/lib/openthread)

#
# canopennode (F:/nrf_project/joiner_v3/modules/lib/canopennode)
#
CONFIG_ZEPHYR_CANOPENNODE_MODULE=y
# end of canopennode (F:/nrf_project/joiner_v3/modules/lib/canopennode)

#
# chre (F:/nrf_project/joiner_v3/modules/lib/chre)
#
CONFIG_ZEPHYR_CHRE_MODULE=y
# CONFIG_CHRE is not set
# end of chre (F:/nrf_project/joiner_v3/modules/lib/chre)

#
# hal_nordic (F:/nrf_project/joiner_v3/modules/hal/nordic)
#
CONFIG_ZEPHYR_HAL_NORDIC_MODULE=y
CONFIG_HAS_NORDIC_DRIVERS=y

#
# Nordic drivers
#
# CONFIG_NRF_802154_SOURCE_HAL_NORDIC is not set
# CONFIG_NRF_802154_SER_HOST is not set
# end of Nordic drivers

CONFIG_HAS_NRFX=y

#
# nrfx drivers
#
CONFIG_NRFX_CLOCK=y
CONFIG_NRFX_CLOCK_LFXO_TWO_STAGE_ENABLED=y
# CONFIG_NRFX_COMP is not set
# CONFIG_NRFX_EGU0 is not set
# CONFIG_NRFX_EGU1 is not set
# CONFIG_NRFX_EGU2 is not set
# CONFIG_NRFX_EGU3 is not set
# CONFIG_NRFX_EGU4 is not set
# CONFIG_NRFX_EGU5 is not set
CONFIG_NRFX_GPIOTE=y
# CONFIG_NRFX_I2S is not set
# CONFIG_NRFX_NFCT is not set
CONFIG_NRFX_NVMC=y
# CONFIG_NRFX_PDM is not set
# CONFIG_NRFX_POWER is not set
CONFIG_NRFX_PPI=y
# CONFIG_NRFX_PWM0 is not set
# CONFIG_NRFX_PWM1 is not set
# CONFIG_NRFX_PWM2 is not set
# CONFIG_NRFX_QDEC is not set
# CONFIG_NRFX_RNG is not set
# CONFIG_NRFX_RTC0 is not set
# CONFIG_NRFX_RTC1 is not set
# CONFIG_NRFX_RTC2 is not set
# CONFIG_NRFX_SAADC is not set
CONFIG_NRFX_SPI=y
CONFIG_NRFX_SPI0=y
CONFIG_NRFX_SPI1=y
CONFIG_NRFX_SPI2=y
# CONFIG_NRFX_SYSTICK is not set
# CONFIG_NRFX_TEMP is not set
# CONFIG_NRFX_TIMER0 is not set
# CONFIG_NRFX_TIMER1 is not set
# CONFIG_NRFX_TIMER2 is not set
# CONFIG_NRFX_TIMER3 is not set
# CONFIG_NRFX_TIMER4 is not set
# CONFIG_NRFX_TWI0 is not set
# CONFIG_NRFX_TWI1 is not set
# CONFIG_NRFX_UARTE0 is not set
CONFIG_NRFX_WDT=y
CONFIG_NRFX_WDT0=y

#
# Peripheral Resource Sharing module
#
# CONFIG_NRFX_PRS_BOX_0 is not set
# CONFIG_NRFX_PRS_BOX_1 is not set
# CONFIG_NRFX_PRS_BOX_2 is not set
# CONFIG_NRFX_PRS_BOX_3 is not set
# CONFIG_NRFX_PRS_BOX_4 is not set
# end of Peripheral Resource Sharing module
# end of nrfx drivers
# end of hal_nordic (F:/nrf_project/joiner_v3/modules/hal/nordic)

#
# liblc3codec (F:/nrf_project/joiner_v3/modules/lib/liblc3codec)
#
CONFIG_ZEPHYR_LIBLC3CODEC_MODULE=y
# end of liblc3codec (F:/nrf_project/joiner_v3/modules/lib/liblc3codec)

#
# littlefs (F:/nrf_project/joiner_v3/modules/fs/littlefs)
#
CONFIG_ZEPHYR_LITTLEFS_MODULE=y
# end of littlefs (F:/nrf_project/joiner_v3/modules/fs/littlefs)

#
# loramac-node (F:/nrf_project/joiner_v3/modules/lib/loramac-node)
#
CONFIG_ZEPHYR_LORAMAC_NODE_MODULE=y
# CONFIG_HAS_SEMTECH_RADIO_DRIVERS is not set
# end of loramac-node (F:/nrf_project/joiner_v3/modules/lib/loramac-node)

#
# lvgl (F:/nrf_project/joiner_v3/modules/lib/gui/lvgl)
#
CONFIG_ZEPHYR_LVGL_MODULE=y
# end of lvgl (F:/nrf_project/joiner_v3/modules/lib/gui/lvgl)

#
# lz4 (F:/nrf_project/joiner_v3/modules/lib/lz4)
#
CONFIG_ZEPHYR_LZ4_MODULE=y
# CONFIG_LZ4 is not set
# end of lz4 (F:/nrf_project/joiner_v3/modules/lib/lz4)

#
# nanopb (F:/nrf_project/joiner_v3/modules/lib/nanopb)
#
CONFIG_ZEPHYR_NANOPB_MODULE=y
# CONFIG_NANOPB is not set
# end of nanopb (F:/nrf_project/joiner_v3/modules/lib/nanopb)

#
# picolibc (F:/nrf_project/joiner_v3/modules/lib/picolibc)
#
# CONFIG_PICOLIBC_MODULE is not set
CONFIG_ZEPHYR_PICOLIBC_MODULE=y
# end of picolibc (F:/nrf_project/joiner_v3/modules/lib/picolibc)

#
# TraceRecorder (F:/nrf_project/joiner_v3/modules/debug/TraceRecorder)
#
CONFIG_ZEPHYR_TRACERECORDER_MODULE=y
# end of TraceRecorder (F:/nrf_project/joiner_v3/modules/debug/TraceRecorder)

#
# zcbor (F:/nrf_project/joiner_v3/modules/lib/zcbor)
#
CONFIG_ZEPHYR_ZCBOR_MODULE=y
# CONFIG_ZCBOR is not set
# end of zcbor (F:/nrf_project/joiner_v3/modules/lib/zcbor)

#
# zscilib (F:/nrf_project/joiner_v3/modules/lib/zscilib)
#
# CONFIG_ZSL is not set
CONFIG_ZEPHYR_ZSCILIB_MODULE=y
# end of zscilib (F:/nrf_project/joiner_v3/modules/lib/zscilib)

#
# nrfxlib (F:/nrf_project/joiner_v3/nrfxlib)
#

#
# Nordic nrfxlib
#
CONFIG_NRF_MODEM_SHMEM_CTRL_SIZE=0x4e8
# CONFIG_NFC_T2T_NRFXLIB is not set
# CONFIG_NFC_T4T_NRFXLIB is not set
# CONFIG_MPSL is not set

#
# Crypto libraries for nRF5x SOCs.
#
# CONFIG_NRF_OBERON is not set
# end of Crypto libraries for nRF5x SOCs.

#
# nrf_security module
#
# CONFIG_NORDIC_SECURITY_BACKEND is not set
# CONFIG_NRF_SECURITY is not set
# end of nrf_security module

# CONFIG_NRF_RPC is not set
CONFIG_NRF_802154_SOURCE_NRFXLIB=y
# CONFIG_GZLL is not set
# CONFIG_NRF_DM is not set
# CONFIG_LC3_PLC_DISABLED is not set
CONFIG_LC3_ENC_CHAN_MAX=1
CONFIG_LC3_DEC_CHAN_MAX=1

#
# Encoder sample rates
#
CONFIG_LC3_ENC_SAMPLE_RATE_8KHZ_SUPPORT=y
CONFIG_LC3_ENC_SAMPLE_RATE_16KHZ_SUPPORT=y
CONFIG_LC3_ENC_SAMPLE_RATE_24KHZ_SUPPORT=y
CONFIG_LC3_ENC_SAMPLE_RATE_32KHZ_SUPPORT=y
CONFIG_LC3_ENC_SAMPLE_RATE_441KHZ_SUPPORT=y
CONFIG_LC3_ENC_SAMPLE_RATE_48KHZ_SUPPORT=y
# end of Encoder sample rates

#
# Decoder sample rates
#
CONFIG_LC3_DEC_SAMPLE_RATE_8KHZ_SUPPORT=y
CONFIG_LC3_DEC_SAMPLE_RATE_16KHZ_SUPPORT=y
CONFIG_LC3_DEC_SAMPLE_RATE_24KHZ_SUPPORT=y
CONFIG_LC3_DEC_SAMPLE_RATE_32KHZ_SUPPORT=y
CONFIG_LC3_DEC_SAMPLE_RATE_441KHZ_SUPPORT=y
CONFIG_LC3_DEC_SAMPLE_RATE_48KHZ_SUPPORT=y
# end of Decoder sample rates
# end of Nordic nrfxlib

CONFIG_ZEPHYR_NRFXLIB_MODULE=y
# end of nrfxlib (F:/nrf_project/joiner_v3/nrfxlib)

#
# connectedhomeip (F:/nrf_project/joiner_v3/modules/lib/matter)
#
CONFIG_ZEPHYR_CONNECTEDHOMEIP_MODULE=y
# end of connectedhomeip (F:/nrf_project/joiner_v3/modules/lib/matter)

#
# Optional modules. Make sure they're installed, via the project manifest.
#
CONFIG_HAS_CMSIS_CORE=y
CONFIG_HAS_CMSIS_CORE_M=y
# CONFIG_CMSIS_NN is not set
# CONFIG_LIBMETAL is not set
# CONFIG_LVGL is not set
# CONFIG_HAS_MEC_HAL is not set
# CONFIG_HAS_MPFS_HAL is not set
# CONFIG_OPENAMP is not set
# CONFIG_SOF is not set
# CONFIG_MIPI_SYST_LIB is not set
# CONFIG_HAS_TELINK_DRIVERS is not set
# CONFIG_TINYCBOR is not set
CONFIG_MCUBOOT_BOOTUTIL_LIB=y

#
# Unavailable modules, please install those via the project manifest.
#

#
# hal_gigadevice module not available.
#

#
# FFF module not available.
#
# end of Modules

CONFIG_BOARD_REVISION="$BOARD_REVISION"
# CONFIG_NET_DRIVERS is not set
CONFIG_BOARD_NRF52DK_NRF52832=y

#
# Board Options
#
CONFIG_BOARD_ENABLE_DCDC=y
# end of Board Options

# CONFIG_SOC_SERIES_BEETLE is not set
# CONFIG_SOC_SERIES_ARM_DESIGNSTART is not set
# CONFIG_SOC_SERIES_FVP_AEMV8R_AARCH32 is not set
# CONFIG_SOC_SERIES_MPS2 is not set
# CONFIG_SOC_SERIES_MPS3 is not set
# CONFIG_SOC_SERIES_MUSCA_B1 is not set
# CONFIG_SOC_SERIES_MUSCA_S1 is not set
# CONFIG_SOC_SERIES_AST10X0 is not set
# CONFIG_SOC_SERIES_SAMD20 is not set
# CONFIG_SOC_SERIES_SAMD21 is not set
# CONFIG_SOC_SERIES_SAMD51 is not set
# CONFIG_SOC_SERIES_SAME51 is not set
# CONFIG_SOC_SERIES_SAME53 is not set
# CONFIG_SOC_SERIES_SAME54 is not set
# CONFIG_SOC_SERIES_SAML21 is not set
# CONFIG_SOC_SERIES_SAMR21 is not set
# CONFIG_SOC_SERIES_SAMR34 is not set
# CONFIG_SOC_SERIES_SAMR35 is not set
# CONFIG_SOC_SERIES_SAM3X is not set
# CONFIG_SOC_SERIES_SAM4E is not set
# CONFIG_SOC_SERIES_SAM4L is not set
# CONFIG_SOC_SERIES_SAM4S is not set
# CONFIG_SOC_SERIES_SAME70 is not set
# CONFIG_SOC_SERIES_SAMV71 is not set
# CONFIG_SOC_SERIES_VALKYRIE is not set
# CONFIG_SOC_SERIES_VIPER is not set
# CONFIG_SOC_SERIES_PSOC62 is not set
# CONFIG_SOC_SERIES_PSOC63 is not set
# CONFIG_SOC_SERIES_GD32E10X is not set
# CONFIG_SOC_SERIES_GD32F3X0 is not set
# CONFIG_SOC_SERIES_GD32F403 is not set
# CONFIG_SOC_SERIES_GD32F4XX is not set
# CONFIG_SOC_SERIES_XMC_4XXX is not set
# CONFIG_SOC_SERIES_CYCLONE5 is not set
# CONFIG_SOC_SERIES_MEC1501X is not set
# CONFIG_SOC_SERIES_MEC1701X is not set
# CONFIG_SOC_SERIES_MEC172X is not set
# CONFIG_SOC_SERIES_NRF51X is not set
CONFIG_SOC_SERIES_NRF52X=y
# CONFIG_SOC_SERIES_NRF53X is not set
# CONFIG_SOC_SERIES_NRF91X is not set
# CONFIG_SOC_SERIES_NPCX7 is not set
# CONFIG_SOC_SERIES_NPCX9 is not set
# CONFIG_SOC_SERIES_M48X is not set
# CONFIG_SOC_SERIES_IMX_6X_M4 is not set
# CONFIG_SOC_SERIES_IMX7_M4 is not set
# CONFIG_SOC_SERIES_IMX8ML_M7 is not set
# CONFIG_SOC_SERIES_IMX8MM_M4 is not set
# CONFIG_SOC_SERIES_IMX8MQ_M4 is not set
# CONFIG_SOC_SERIES_IMX_RT5XX is not set
# CONFIG_SOC_SERIES_IMX_RT6XX is not set
# CONFIG_SOC_SERIES_IMX_RT is not set
# CONFIG_SOC_SERIES_KINETIS_K2X is not set
# CONFIG_SOC_SERIES_KINETIS_K6X is not set
# CONFIG_SOC_SERIES_KINETIS_K8X is not set
# CONFIG_SOC_SERIES_KINETIS_KE1XF is not set
# CONFIG_SOC_SERIES_KINETIS_KL2X is not set
# CONFIG_SOC_SERIES_KINETIS_KV5X is not set
# CONFIG_SOC_SERIES_KINETIS_KWX is not set
# CONFIG_SOC_SERIES_LPC11U6X is not set
# CONFIG_SOC_SERIES_LPC54XXX is not set
# CONFIG_SOC_SERIES_LPC55XXX is not set
# CONFIG_SOC_EOS_S3 is not set
# CONFIG_SOC_SERIES_RCAR_GEN3 is not set
# CONFIG_SOC_SERIES_RP2XXX is not set
# CONFIG_SOC_SERIES_EFM32GG11B is not set
# CONFIG_SOC_SERIES_EFM32HG is not set
# CONFIG_SOC_SERIES_EFM32JG12B is not set
# CONFIG_SOC_SERIES_EFM32PG12B is not set
# CONFIG_SOC_SERIES_EFM32PG1B is not set
# CONFIG_SOC_SERIES_EFM32WG is not set
# CONFIG_SOC_SERIES_EFR32BG13P is not set
# CONFIG_SOC_SERIES_EFR32FG13P is not set
# CONFIG_SOC_SERIES_EFR32FG1P is not set
# CONFIG_SOC_SERIES_EFR32MG12P is not set
# CONFIG_SOC_SERIES_EFR32MG21 is not set
# CONFIG_SOC_SERIES_STM32F0X is not set
# CONFIG_SOC_SERIES_STM32F1X is not set
# CONFIG_SOC_SERIES_STM32F2X is not set
# CONFIG_SOC_SERIES_STM32F3X is not set
# CONFIG_SOC_SERIES_STM32F4X is not set
# CONFIG_SOC_SERIES_STM32F7X is not set
# CONFIG_SOC_SERIES_STM32G0X is not set
# CONFIG_SOC_SERIES_STM32G4X is not set
# CONFIG_SOC_SERIES_STM32H7X is not set
# CONFIG_SOC_SERIES_STM32L0X is not set
# CONFIG_SOC_SERIES_STM32L1X is not set
# CONFIG_SOC_SERIES_STM32L4X is not set
# CONFIG_SOC_SERIES_STM32L5X is not set
# CONFIG_SOC_SERIES_STM32MP1X is not set
# CONFIG_SOC_SERIES_STM32U5X is not set
# CONFIG_SOC_SERIES_STM32WBX is not set
# CONFIG_SOC_SERIES_STM32WLX is not set
# CONFIG_SOC_TI_LM3S6965 is not set
# CONFIG_SOC_SERIES_CC13X2_CC26X2 is not set
# CONFIG_SOC_SERIES_CC32XX is not set
# CONFIG_SOC_SERIES_MSP432P4XX is not set
# CONFIG_SOC_SERIES_XILINX_XC7ZXXX is not set
# CONFIG_SOC_SERIES_XILINX_XC7ZXXXS is not set
# CONFIG_SOC_XILINX_ZYNQMP_RPU is not set

#
# Hardware Configuration
#
CONFIG_CPU_HAS_ARM_MPU=y
CONFIG_HAS_SWO=y
CONFIG_SOC_FAMILY="nordic_nrf"
CONFIG_SOC_FAMILY_NRF=y
CONFIG_HAS_HW_NRF_BPROT=y
CONFIG_HAS_HW_NRF_CCM=y
CONFIG_HAS_HW_NRF_CCM_LFLEN_8BIT=y
CONFIG_HAS_HW_NRF_CLOCK=y
CONFIG_HAS_HW_NRF_ECB=y
CONFIG_HAS_HW_NRF_EGU0=y
CONFIG_HAS_HW_NRF_EGU1=y
CONFIG_HAS_HW_NRF_EGU2=y
CONFIG_HAS_HW_NRF_EGU3=y
CONFIG_HAS_HW_NRF_EGU4=y
CONFIG_HAS_HW_NRF_EGU5=y
CONFIG_HAS_HW_NRF_GPIO0=y
CONFIG_HAS_HW_NRF_GPIOTE=y
CONFIG_HAS_HW_NRF_POWER=y
CONFIG_HAS_HW_NRF_PPI=y
CONFIG_HAS_HW_NRF_RADIO_BLE_2M=y
CONFIG_HAS_HW_NRF_RNG=y
CONFIG_HAS_HW_NRF_RTC0=y
CONFIG_HAS_HW_NRF_RTC1=y
CONFIG_HAS_HW_NRF_RTC2=y
CONFIG_HAS_HW_NRF_SAADC=y
CONFIG_HAS_HW_NRF_SPI0=y
CONFIG_HAS_HW_NRF_SPI1=y
CONFIG_HAS_HW_NRF_SPI2=y
CONFIG_HAS_HW_NRF_SWI0=y
CONFIG_HAS_HW_NRF_SWI1=y
CONFIG_HAS_HW_NRF_SWI2=y
CONFIG_HAS_HW_NRF_SWI3=y
CONFIG_HAS_HW_NRF_SWI4=y
CONFIG_HAS_HW_NRF_SWI5=y
CONFIG_HAS_HW_NRF_TEMP=y
CONFIG_HAS_HW_NRF_TIMER0=y
CONFIG_HAS_HW_NRF_TIMER1=y
CONFIG_HAS_HW_NRF_TIMER2=y
CONFIG_HAS_HW_NRF_TIMER3=y
CONFIG_HAS_HW_NRF_TIMER4=y
CONFIG_HAS_HW_NRF_UARTE0=y
CONFIG_HAS_HW_NRF_WDT0=y
CONFIG_NRF_HW_RTC1_RESERVED=y
CONFIG_SOC_NRF52832=y
# CONFIG_SOC_NRF52805_CAAA is not set
# CONFIG_SOC_NRF52810_QFAA is not set
# CONFIG_SOC_NRF52811_QFAA is not set
# CONFIG_SOC_NRF52820_QDAA is not set
# CONFIG_SOC_NRF52832_CIAA is not set
CONFIG_SOC_NRF52832_QFAA=y
# CONFIG_SOC_NRF52832_QFAB is not set
# CONFIG_SOC_NRF52833_QIAA is not set
# CONFIG_SOC_NRF52840_QIAA is not set
CONFIG_SOC_DCDC_NRF52X=y
CONFIG_GPIO_AS_PINRESET=y
CONFIG_NRF_ENABLE_ICACHE=y
CONFIG_NRF52_ANOMALY_132_DELAY_US=330
CONFIG_NRF_RTC_TIMER_USER_CHAN_COUNT=0
CONFIG_NRF_SOC_SECURE_SUPPORTED=y
CONFIG_NFCT_PINS_AS_GPIOS=y
CONFIG_NRF_APPROTECT_USE_UICR=y
# CONFIG_NRF_APPROTECT_LOCK is not set
# CONFIG_NRF_TRACE_PORT is not set
# CONFIG_SOC_LOG_LEVEL_OFF is not set
# CONFIG_SOC_LOG_LEVEL_ERR is not set
# CONFIG_SOC_LOG_LEVEL_WRN is not set
CONFIG_SOC_LOG_LEVEL_INF=y
# CONFIG_SOC_LOG_LEVEL_DBG is not set
CONFIG_SOC_LOG_LEVEL=3
# end of Hardware Configuration

CONFIG_SOC_COMPATIBLE_NRF=y
CONFIG_SOC_COMPATIBLE_NRF52X=y
CONFIG_SOC_COMPATIBLE_NRF52832=y

#
# ARM Options
#
CONFIG_ARCH="arm"
CONFIG_CPU_CORTEX=y
# CONFIG_CODE_DATA_RELOCATION_SRAM is not set
CONFIG_CPU_CORTEX_M=y
CONFIG_ISA_THUMB2=y
CONFIG_ASSEMBLER_ISA_THUMB2=y
CONFIG_COMPILER_ISA_THUMB2=y
CONFIG_STACK_ALIGN_DOUBLE_WORD=y
# CONFIG_RUNTIME_NMI is not set
CONFIG_FAULT_DUMP=2
CONFIG_ARM_STACK_PROTECTION=y
CONFIG_FP16=y
CONFIG_FP16_IEEE=y
# CONFIG_FP16_ALT is not set
CONFIG_CPU_CORTEX_M4=y
CONFIG_CPU_CORTEX_M_HAS_SYSTICK=y
CONFIG_CPU_CORTEX_M_HAS_DWT=y
CONFIG_CPU_CORTEX_M_HAS_BASEPRI=y
CONFIG_CPU_CORTEX_M_HAS_VTOR=y
CONFIG_CPU_CORTEX_M_HAS_PROGRAMMABLE_FAULT_PRIOS=y
CONFIG_ARMV7_M_ARMV8_M_MAINLINE=y
CONFIG_ARMV7_M_ARMV8_M_FP=y

#
# ARM Cortex-M0/M0+/M1/M3/M4/M7/M23/M33 options
#
CONFIG_GEN_ISR_TABLES=y
# CONFIG_ZERO_LATENCY_IRQS is not set
# CONFIG_SW_VECTOR_RELAY is not set
# CONFIG_CORTEX_M_DWT is not set
# CONFIG_TRAP_UNALIGNED_ACCESS is not set
# end of ARM Cortex-M0/M0+/M1/M3/M4/M7/M23/M33 options

CONFIG_NULL_POINTER_EXCEPTION_DETECTION_NONE=y
# CONFIG_NULL_POINTER_EXCEPTION_DETECTION_DWT is not set
# CONFIG_NULL_POINTER_EXCEPTION_DETECTION_MPU is not set
CONFIG_GEN_IRQ_VECTOR_TABLE=y
CONFIG_ARM_MPU=y
CONFIG_ARM_MPU_REGION_MIN_ALIGN_AND_SIZE=32
CONFIG_MPU_STACK_GUARD=y
CONFIG_MPU_ALLOW_FLASH_WRITE=y
# CONFIG_CUSTOM_SECTION_ALIGN is not set
CONFIG_CUSTOM_SECTION_MIN_ALIGN_SIZE=32
# end of ARM Options

CONFIG_ARM=y
CONFIG_ARCH_IS_SET=y

#
# General Architecture Options
#
# CONFIG_SEMIHOST is not set
# CONFIG_ARCH_LOG_LEVEL_OFF is not set
# CONFIG_ARCH_LOG_LEVEL_ERR is not set
# CONFIG_ARCH_LOG_LEVEL_WRN is not set
CONFIG_ARCH_LOG_LEVEL_INF=y
# CONFIG_ARCH_LOG_LEVEL_DBG is not set
CONFIG_ARCH_LOG_LEVEL=3
CONFIG_HW_STACK_PROTECTION=y
# CONFIG_USERSPACE is not set
CONFIG_KOBJECT_TEXT_AREA=256
CONFIG_KOBJECT_DATA_AREA_RESERVE_EXTRA_PERCENT=100
CONFIG_KOBJECT_RODATA_AREA_EXTRA_BYTES=16
CONFIG_GEN_PRIV_STACKS=y
# CONFIG_STACK_GROWS_UP is not set

#
# Interrupt Configuration
#
# CONFIG_DYNAMIC_INTERRUPTS is not set
CONFIG_ARCH_IRQ_VECTOR_TABLE_ALIGN=4
CONFIG_IRQ_VECTOR_TABLE_JUMP_BY_ADDRESS=y
# CONFIG_IRQ_VECTOR_TABLE_JUMP_BY_CODE is not set
CONFIG_GEN_SW_ISR_TABLE=y
CONFIG_ARCH_SW_ISR_TABLE_ALIGN=4
CONFIG_GEN_IRQ_START_VECTOR=0
# CONFIG_EXTRA_EXCEPTION_INFO is not set
# end of Interrupt Configuration
# end of General Architecture Options

CONFIG_ARCH_HAS_SINGLE_THREAD_SUPPORT=y
CONFIG_ARCH_HAS_TIMING_FUNCTIONS=y
CONFIG_ARCH_HAS_STACK_PROTECTION=y
CONFIG_ARCH_HAS_USERSPACE=y
CONFIG_ARCH_HAS_EXECUTABLE_PAGE_BIT=y
CONFIG_ARCH_HAS_RAMFUNC_SUPPORT=y
CONFIG_ARCH_HAS_NESTED_EXCEPTION_DETECTION=y
CONFIG_ARCH_SUPPORTS_COREDUMP=y
CONFIG_ARCH_SUPPORTS_ARCH_HW_INIT=y
CONFIG_ARCH_HAS_EXTRA_EXCEPTION_INFO=y
CONFIG_ARCH_HAS_THREAD_LOCAL_STORAGE=y
CONFIG_ARCH_HAS_SUSPEND_TO_RAM=y
CONFIG_ARCH_HAS_THREAD_ABORT=y
CONFIG_CPU_HAS_FPU=y
CONFIG_CPU_HAS_MPU=y
CONFIG_MPU=y
# CONFIG_MPU_LOG_LEVEL_OFF is not set
# CONFIG_MPU_LOG_LEVEL_ERR is not set
# CONFIG_MPU_LOG_LEVEL_WRN is not set
CONFIG_MPU_LOG_LEVEL_INF=y
# CONFIG_MPU_LOG_LEVEL_DBG is not set
CONFIG_MPU_LOG_LEVEL=3
CONFIG_MPU_REQUIRES_POWER_OF_TWO_ALIGNMENT=y
CONFIG_SRAM_REGION_PERMISSIONS=y

#
# Floating Point Options
#
# end of Floating Point Options

#
# Cache Options
#
CONFIG_DCACHE=y
# CONFIG_CACHE_MANAGEMENT is not set
# end of Cache Options

CONFIG_TOOLCHAIN_HAS_BUILTIN_FFS=y

#
# General Kernel Options
#
# CONFIG_KERNEL_LOG_LEVEL_OFF is not set
# CONFIG_KERNEL_LOG_LEVEL_ERR is not set
# CONFIG_KERNEL_LOG_LEVEL_WRN is not set
CONFIG_KERNEL_LOG_LEVEL_INF=y
# CONFIG_KERNEL_LOG_LEVEL_DBG is not set
CONFIG_KERNEL_LOG_LEVEL=3
CONFIG_NUM_COOP_PRIORITIES=16
CONFIG_NUM_PREEMPT_PRIORITIES=15
CONFIG_MAIN_THREAD_PRIORITY=0
CONFIG_COOP_ENABLED=y
CONFIG_PREEMPT_ENABLED=y
CONFIG_PRIORITY_CEILING=-127
# CONFIG_SCHED_DEADLINE is not set
# CONFIG_SCHED_CPU_MASK is not set
CONFIG_IDLE_STACK_SIZE=320
CONFIG_ISR_STACK_SIZE=2048
CONFIG_THREAD_STACK_INFO=y
# CONFIG_THREAD_CUSTOM_DATA is not set
CONFIG_ERRNO=y
CONFIG_SCHED_DUMB=y
# CONFIG_SCHED_SCALABLE is not set
# CONFIG_SCHED_MULTIQ is not set
# CONFIG_WAITQ_SCALABLE is not set
CONFIG_WAITQ_DUMB=y

#
# Kernel Debugging and Metrics
#
CONFIG_BOOT_BANNER=y
CONFIG_BOOT_DELAY=0
# CONFIG_THREAD_MONITOR is not set
# CONFIG_THREAD_NAME is not set
# CONFIG_THREAD_RUNTIME_STATS is not set
# end of Kernel Debugging and Metrics

#
# Work Queue Options
#
CONFIG_SYSTEM_WORKQUEUE_PRIORITY=-1
# CONFIG_SYSTEM_WORKQUEUE_NO_YIELD is not set
# end of Work Queue Options

#
# Atomic Operations
#
CONFIG_ATOMIC_OPERATIONS_BUILTIN=y
# end of Atomic Operations

#
# Timer API Options
#
CONFIG_TIMESLICING=y
CONFIG_TIMESLICE_SIZE=0
CONFIG_TIMESLICE_PRIORITY=0
# CONFIG_TIMESLICE_PER_THREAD is not set
# CONFIG_POLL is not set
# end of Timer API Options

#
# Other Kernel Object Options
#
# CONFIG_MEM_SLAB_TRACE_MAX_UTILIZATION is not set
CONFIG_NUM_MBOX_ASYNC_MSGS=10
# CONFIG_EVENTS is not set
CONFIG_KERNEL_MEM_POOL=y
# end of Other Kernel Object Options

CONFIG_ARCH_HAS_CUSTOM_SWAP_TO_MAIN=y
CONFIG_SWAP_NONATOMIC=y
CONFIG_SYS_CLOCK_EXISTS=y
CONFIG_TIMEOUT_64BIT=y
CONFIG_SYS_CLOCK_MAX_TIMEOUT_DAYS=365
CONFIG_XIP=y

#
# Initialization Priorities
#
CONFIG_KERNEL_INIT_PRIORITY_OBJECTS=30
CONFIG_KERNEL_INIT_PRIORITY_DEFAULT=40
CONFIG_KERNEL_INIT_PRIORITY_DEVICE=50
CONFIG_APPLICATION_INIT_PRIORITY=90
# end of Initialization Priorities

#
# Security Options
#
# end of Security Options

#
# SMP Options
#
# end of SMP Options

CONFIG_TICKLESS_KERNEL=y
CONFIG_TOOLCHAIN_SUPPORTS_THREAD_LOCAL_STORAGE=y
# CONFIG_THREAD_LOCAL_STORAGE is not set
# end of General Kernel Options

#
# Device Options
#
# end of Device Options

#
# Virtual Memory Support
#
# end of Virtual Memory Support

CONFIG_HAS_DTS=y

#
# Devicetree Info
#
CONFIG_DT_HAS_ADI_ADXL362_ENABLED=y
CONFIG_DT_HAS_ARDUINO_UNO_ADC_ENABLED=y
CONFIG_DT_HAS_ARDUINO_HEADER_R3_ENABLED=y
CONFIG_DT_HAS_ARM_ARMV7M_ITM_ENABLED=y
CONFIG_DT_HAS_ARM_CORTEX_M4F_ENABLED=y
CONFIG_DT_HAS_ARM_V7M_NVIC_ENABLED=y
CONFIG_DT_HAS_FIXED_PARTITIONS_ENABLED=y
CONFIG_DT_HAS_GPIO_KEYS_ENABLED=y
CONFIG_DT_HAS_GPIO_LEDS_ENABLED=y
CONFIG_DT_HAS_JEDEC_SPI_NOR_ENABLED=y
CONFIG_DT_HAS_MMIO_SRAM_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_BPROT_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_CCM_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_CLOCK_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_ECB_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_EGU_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_FICR_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_GPIO_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_GPIOTE_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_MWU_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_PINCTRL_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_POWER_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_PPI_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_RADIO_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_RNG_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_RTC_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_SAADC_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_SPI_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_SWI_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_TEMP_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_TIMER_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_UARTE_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_UICR_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_WDT_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF52_FLASH_CONTROLLER_ENABLED=y
CONFIG_DT_HAS_PWM_LEDS_ENABLED=y
CONFIG_DT_HAS_SOC_NV_FLASH_ENABLED=y
CONFIG_DT_HAS_ZEPHYR_BT_HCI_ENTROPY_ENABLED=y
# end of Devicetree Info

#
# Device Drivers
#
# CONFIG_IEEE802154 is not set
# CONFIG_LORA is not set
CONFIG_CONSOLE=y
CONFIG_CONSOLE_INPUT_MAX_LINE_LEN=128
CONFIG_CONSOLE_HAS_DRIVER=y
CONFIG_CONSOLE_HANDLER=y
CONFIG_CONSOLE_INIT_PRIORITY=60
CONFIG_UART_CONSOLE=y
# CONFIG_UART_CONSOLE_DEBUG_SERVER_HOOKS is not set
# CONFIG_UART_CONSOLE_MCUMGR is not set
# CONFIG_RAM_CONSOLE is not set
# CONFIG_RTT_CONSOLE is not set
# CONFIG_IPM_CONSOLE_SENDER is not set
# CONFIG_IPM_CONSOLE_RECEIVER is not set
# CONFIG_UART_MCUMGR is not set
# CONFIG_UART_CONSOLE_LOG_LEVEL_OFF is not set
# CONFIG_UART_CONSOLE_LOG_LEVEL_ERR is not set
# CONFIG_UART_CONSOLE_LOG_LEVEL_WRN is not set
CONFIG_UART_CONSOLE_LOG_LEVEL_INF=y
# CONFIG_UART_CONSOLE_LOG_LEVEL_DBG is not set
CONFIG_UART_CONSOLE_LOG_LEVEL=3
# CONFIG_GSM_MUX is not set
# CONFIG_EFI_CONSOLE is not set
CONFIG_HAS_SEGGER_RTT=y
CONFIG_USE_SEGGER_RTT=y
CONFIG_SEGGER_RTT_CUSTOM_LOCKING=y
CONFIG_SEGGER_RTT_MAX_NUM_UP_BUFFERS=3
CONFIG_SEGGER_RTT_MAX_NUM_DOWN_BUFFERS=3
CONFIG_SEGGER_RTT_BUFFER_SIZE_UP=1024
CONFIG_SEGGER_RTT_BUFFER_SIZE_DOWN=16
CONFIG_SEGGER_RTT_PRINTF_BUFFER_SIZE=64
CONFIG_SEGGER_RTT_MODE_NO_BLOCK_SKIP=y
# CONFIG_SEGGER_RTT_MODE_NO_BLOCK_TRIM is not set
# CONFIG_SEGGER_RTT_MODE_BLOCK_IF_FIFO_FULL is not set
CONFIG_SEGGER_RTT_MODE=0
# CONFIG_SEGGER_RTT_MEMCPY_USE_BYTELOOP is not set
CONFIG_SEGGER_RTT_SECTION_NONE=y
# CONFIG_SEGGER_RTT_SECTION_DTCM is not set
# CONFIG_EC_HOST_CMD_PERIPH is not set
# CONFIG_MDIO is not set

#
# Capabilities
#
CONFIG_SERIAL_HAS_DRIVER=y
CONFIG_SERIAL_SUPPORT_ASYNC=y
CONFIG_SERIAL_SUPPORT_INTERRUPT=y
# CONFIG_UART_LOG_LEVEL_OFF is not set
# CONFIG_UART_LOG_LEVEL_ERR is not set
# CONFIG_UART_LOG_LEVEL_WRN is not set
CONFIG_UART_LOG_LEVEL_INF=y
# CONFIG_UART_LOG_LEVEL_DBG is not set
CONFIG_UART_LOG_LEVEL=3
CONFIG_UART_USE_RUNTIME_CONFIGURE=y
# CONFIG_UART_ASYNC_API is not set
# CONFIG_UART_LINE_CTRL is not set
# CONFIG_UART_DRV_CMD is not set
# CONFIG_UART_WIDE_DATA is not set
# CONFIG_UART_PIPE is not set

#
# Serial Drivers
#
CONFIG_UART_NRFX=y
CONFIG_UART_0_NRF_UARTE=y
CONFIG_UART_0_ENHANCED_POLL_OUT=y
CONFIG_UART_0_INTERRUPT_DRIVEN=y
# CONFIG_UART_0_NRF_PARITY_BIT is not set
CONFIG_UART_0_NRF_TX_BUFFER_SIZE=32
CONFIG_UART_ENHANCED_POLL_OUT=y
CONFIG_NRF_UARTE_PERIPHERAL=y

#
# Interrupt Controllers
#
# CONFIG_SWERV_PIC is not set
CONFIG_INTC_INIT_PRIORITY=40
# CONFIG_INTC_LOG_LEVEL_OFF is not set
# CONFIG_INTC_LOG_LEVEL_ERR is not set
# CONFIG_INTC_LOG_LEVEL_WRN is not set
CONFIG_INTC_LOG_LEVEL_INF=y
# CONFIG_INTC_LOG_LEVEL_DBG is not set
CONFIG_INTC_LOG_LEVEL=3
# CONFIG_MULTI_LEVEL_INTERRUPTS is not set
# CONFIG_INTC_ESP32 is not set
# end of Interrupt Controllers

#
# Timer Drivers
#
# CONFIG_TIMER_READS_ITS_FREQUENCY_AT_RUNTIME is not set
# CONFIG_SYSTEM_CLOCK_SLOPPY_IDLE is not set
CONFIG_SYSTEM_CLOCK_INIT_PRIORITY=0
CONFIG_TICKLESS_CAPABLE=y
# CONFIG_INTEL_ADSP_TIMER is not set
# CONFIG_HPET_TIMER is not set
# CONFIG_SYSTEM_CLOCK_NO_WAIT is not set
# CONFIG_SYSTEM_CLOCK_WAIT_FOR_AVAILABILITY is not set
CONFIG_SYSTEM_CLOCK_WAIT_FOR_STABILITY=y
CONFIG_RISCV_MACHINE_TIMER_SYSTEM_CLOCK_DIVIDER=0
CONFIG_RISCV_MACHINE_TIMER_MIN_DELAY=100
# end of Timer Drivers

# CONFIG_PCIE is not set
# CONFIG_PCIE_ENDPOINT is not set
# CONFIG_GPIO_LOG_LEVEL_OFF is not set
# CONFIG_GPIO_LOG_LEVEL_ERR is not set
# CONFIG_GPIO_LOG_LEVEL_WRN is not set
CONFIG_GPIO_LOG_LEVEL_INF=y
# CONFIG_GPIO_LOG_LEVEL_DBG is not set
CONFIG_GPIO_LOG_LEVEL=3
# CONFIG_GPIO_GET_DIRECTION is not set
# CONFIG_GPIO_GET_CONFIG is not set
CONFIG_GPIO_NRFX=y
# CONFIG_FXL6408_LOG_LEVEL_OFF is not set
# CONFIG_FXL6408_LOG_LEVEL_ERR is not set
# CONFIG_FXL6408_LOG_LEVEL_WRN is not set
CONFIG_FXL6408_LOG_LEVEL_INF=y
# CONFIG_FXL6408_LOG_LEVEL_DBG is not set
CONFIG_FXL6408_LOG_LEVEL=3
# CONFIG_SHARED_IRQ is not set
# CONFIG_SPI_ASYNC is not set
# CONFIG_SPI_SLAVE is not set
# CONFIG_SPI_EXTENDED_MODES is not set
CONFIG_SPI_INIT_PRIORITY=70
CONFIG_SPI_COMPLETION_TIMEOUT_TOLERANCE=200
# CONFIG_SPI_LOG_LEVEL_OFF is not set
# CONFIG_SPI_LOG_LEVEL_ERR is not set
# CONFIG_SPI_LOG_LEVEL_WRN is not set
CONFIG_SPI_LOG_LEVEL_INF=y
# CONFIG_SPI_LOG_LEVEL_DBG is not set
CONFIG_SPI_LOG_LEVEL=3
CONFIG_SPI_NRFX=y
# CONFIG_SOC_NRF52832_ALLOW_SPIM_DESPITE_PAN_58 is not set
CONFIG_SPI_0_NRF_SPI=y
CONFIG_SPI_1_NRF_SPI=y
CONFIG_SPI_2_NRF_SPI=y
# CONFIG_SDHC is not set
# CONFIG_I2S is not set
# CONFIG_DAI is not set
# CONFIG_PWM is not set
# CONFIG_PINMUX is not set
# CONFIG_ADC is not set
# CONFIG_DAC is not set
# CONFIG_W1 is not set
# CONFIG_CLOCK_CONTROL_LOG_LEVEL_OFF is not set
# CONFIG_CLOCK_CONTROL_LOG_LEVEL_ERR is not set
# CONFIG_CLOCK_CONTROL_LOG_LEVEL_WRN is not set
CONFIG_CLOCK_CONTROL_LOG_LEVEL_INF=y
# CONFIG_CLOCK_CONTROL_LOG_LEVEL_DBG is not set
CONFIG_CLOCK_CONTROL_LOG_LEVEL=3
CONFIG_CLOCK_CONTROL_NRF=y
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC is not set
CONFIG_CLOCK_CONTROL_NRF_K32SRC_XTAL=y
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_SYNTH is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_EXT_LOW_SWING is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_EXT_FULL_SWING is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_500PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_250PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_150PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_100PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_75PPM is not set
CONFIG_CLOCK_CONTROL_NRF_K32SRC_50PPM=y
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_30PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_20PPM is not set
CONFIG_CLOCK_CONTROL_NRF_ACCURACY=50
# CONFIG_PTP_CLOCK is not set
# CONFIG_IPM is not set
CONFIG_FLASH_HAS_DRIVER_ENABLED=y
CONFIG_FLASH_HAS_PAGE_LAYOUT=y
CONFIG_FLASH_JESD216=y
# CONFIG_FLASH_JESD216_API is not set
CONFIG_FLASH=y
# CONFIG_FLASH_LOG_LEVEL_OFF is not set
# CONFIG_FLASH_LOG_LEVEL_ERR is not set
# CONFIG_FLASH_LOG_LEVEL_WRN is not set
CONFIG_FLASH_LOG_LEVEL_INF=y
# CONFIG_FLASH_LOG_LEVEL_DBG is not set
CONFIG_FLASH_LOG_LEVEL=3
CONFIG_FLASH_PAGE_LAYOUT=y
CONFIG_FLASH_INIT_PRIORITY=50
CONFIG_SOC_FLASH_NRF=y
CONFIG_SOC_FLASH_NRF_RADIO_SYNC_NONE=y
# CONFIG_SOC_FLASH_NRF_UICR is not set
# CONFIG_SOC_FLASH_NRF_EMULATE_ONE_BYTE_WRITE_ACCESS is not set
CONFIG_SPI_NOR=y
CONFIG_SPI_NOR_SFDP_MINIMAL=y
# CONFIG_SPI_NOR_SFDP_DEVICETREE is not set
# CONFIG_SPI_NOR_SFDP_RUNTIME is not set
CONFIG_SPI_NOR_INIT_PRIORITY=80
CONFIG_SPI_NOR_CS_WAIT_DELAY=0
CONFIG_SPI_NOR_FLASH_LAYOUT_PAGE_SIZE=65536
# CONFIG_SPI_NOR_IDLE_IN_DPD is not set
# CONFIG_COUNTER is not set
# CONFIG_DMA is not set
# CONFIG_USB_DEVICE_DRIVER is not set
# CONFIG_CRYPTO is not set
# CONFIG_DISPLAY is not set
# CONFIG_LED_STRIP is not set
# CONFIG_LED is not set
# CONFIG_CAN is not set
# CONFIG_AUDIO is not set
# CONFIG_NEURAL_NET_ACCEL is not set
# CONFIG_HWINFO is not set
# CONFIG_ESPI is not set
# CONFIG_PS2 is not set
# CONFIG_VIDEO is not set
# CONFIG_EEPROM is not set
# CONFIG_PECI is not set
# CONFIG_PECI_INTERRUPT_DRIVEN is not set
# CONFIG_REGULATOR is not set
# CONFIG_MEMC is not set
# CONFIG_VIRTUALIZATION is not set
# CONFIG_EDAC is not set
# CONFIG_PM_CPU_OPS is not set

#
# Miscellaneous Drivers
#
# CONFIG_GROVE_LCD_RGB is not set
# end of Miscellaneous Drivers

# CONFIG_DISK_DRIVERS is not set
# CONFIG_CACHE is not set
# CONFIG_SYSCON is not set
# CONFIG_BBRAM is not set
# CONFIG_FPGA is not set
# CONFIG_PINCTRL_LOG_LEVEL_OFF is not set
# CONFIG_PINCTRL_LOG_LEVEL_ERR is not set
# CONFIG_PINCTRL_LOG_LEVEL_WRN is not set
CONFIG_PINCTRL_LOG_LEVEL_INF=y
# CONFIG_PINCTRL_LOG_LEVEL_DBG is not set
CONFIG_PINCTRL_LOG_LEVEL=3
CONFIG_PINCTRL_STORE_REG=y
# CONFIG_PINCTRL_DYNAMIC is not set
CONFIG_PINCTRL_NRF=y
CONFIG_PINCTRL_STM32_REMAP_INIT_PRIORITY=2
# CONFIG_MBOX is not set
# CONFIG_MM_DRV is not set
# CONFIG_POWER_DOMAIN is not set
# CONFIG_USBC_TCPC_DRIVER is not set
# CONFIG_RESET is not set
# CONFIG_MIPI_DSI is not set
# CONFIG_COREDUMP_DEVICE is not set
# end of Device Drivers

#
# C Library
#
CONFIG_SUPPORT_MINIMAL_LIBC=y
CONFIG_PICOLIBC_SUPPORTED=y
CONFIG_MINIMAL_LIBC=y
# CONFIG_PICOLIBC is not set
# CONFIG_NEWLIB_LIBC is not set
# CONFIG_EXTERNAL_LIBC is not set
CONFIG_HAS_NEWLIB_LIBC_NANO=y
CONFIG_MINIMAL_LIBC_NON_REENTRANT_FUNCTIONS=y
CONFIG_MINIMAL_LIBC_MALLOC=y
CONFIG_MINIMAL_LIBC_MALLOC_ARENA_SIZE=0
CONFIG_MINIMAL_LIBC_CALLOC=y
CONFIG_MINIMAL_LIBC_REALLOCARRAY=y
# CONFIG_MINIMAL_LIBC_LL_PRINTF is not set
CONFIG_MINIMAL_LIBC_OPTIMIZE_STRING_FOR_SIZE=y
# CONFIG_MINIMAL_LIBC_RAND is not set
CONFIG_MINIMAL_LIBC_TIME=y
# CONFIG_MINIMAL_LIBC_STRING_ERROR_TABLE is not set
CONFIG_STDOUT_CONSOLE=y
CONFIG_NEED_LIBC_MEM_PARTITION=y
# end of C Library

#
# Additional libraries
#

#
# OS Support Library
#
# CONFIG_JSON_LIBRARY is not set
# CONFIG_RING_BUFFER is not set
# CONFIG_BASE64 is not set
# CONFIG_PRINTK_SYNC is not set
# CONFIG_MPSC_PBUF is not set
# CONFIG_SPSC_PBUF is not set
# CONFIG_SHARED_MULTI_HEAP is not set
# CONFIG_WINSTREAM is not set
CONFIG_REBOOT=y
# CONFIG_UTF8 is not set
# CONFIG_CBPRINTF_COMPLETE is not set
CONFIG_CBPRINTF_NANO=y
CONFIG_CBPRINTF_FULL_INTEGRAL=y
# CONFIG_CBPRINTF_REDUCED_INTEGRAL is not set
# CONFIG_CBPRINTF_FP_A_SUPPORT is not set
# CONFIG_CBPRINTF_FP_ALWAYS_A is not set
CONFIG_CBPRINTF_LIBC_SUBSTS=y
# CONFIG_CBPRINTF_PACKAGE_LONGDOUBLE is not set
# CONFIG_CBPRINTF_STATIC_PACKAGE_CHECK_ALIGNMENT is not set

#
# Heap and Memory Allocation
#
# CONFIG_SYS_HEAP_VALIDATE is not set
CONFIG_SYS_HEAP_ALLOC_LOOPS=3
# CONFIG_SYS_HEAP_RUNTIME_STATS is not set
# CONFIG_SYS_HEAP_LISTENER is not set
CONFIG_SYS_HEAP_SMALL_ONLY=y
# CONFIG_SYS_HEAP_BIG_ONLY is not set
# CONFIG_SYS_HEAP_AUTO is not set
# CONFIG_SYS_MEM_BLOCKS is not set
# end of Heap and Memory Allocation
# end of OS Support Library

# CONFIG_GETOPT is not set
CONFIG_POSIX_MAX_FDS=4
# CONFIG_POSIX_API is not set
# CONFIG_POSIX_CLOCK is not set
CONFIG_MAX_TIMER_COUNT=5
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_EVENTFD is not set
# CONFIG_OPENAMP_RSC_TABLE is not set

#
# Util libraries
#
# CONFIG_FNMATCH is not set
# end of Util libraries

# CONFIG_SMF is not set
# end of Additional libraries

#
# Sub Systems and OS Services
#
# CONFIG_BT is not set

#
# Controller Area Network (CAN) bus subsystem
#
# CONFIG_ISOTP is not set
# end of Controller Area Network (CAN) bus subsystem

# CONFIG_CONSOLE_SUBSYS is not set
# CONFIG_CPLUSPLUS is not set

#
# System Monitoring Options
#
# CONFIG_THREAD_ANALYZER is not set
# end of System Monitoring Options

#
# Debugging Options
#
# CONFIG_DEBUG is not set
# CONFIG_STACK_USAGE is not set
# CONFIG_STACK_SENTINEL is not set
CONFIG_PRINTK=y
CONFIG_EARLY_CONSOLE=y
# CONFIG_ASSERT is not set
# CONFIG_FORCE_NO_ASSERT is not set
CONFIG_ASSERT_VERBOSE=y
# CONFIG_ASSERT_NO_FILE_INFO is not set
# CONFIG_ASSERT_NO_COND_INFO is not set
# CONFIG_ASSERT_NO_MSG_INFO is not set
# CONFIG_OVERRIDE_FRAME_POINTER_DEFAULT is not set
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_THREAD_INFO is not set
# CONFIG_DEBUG_COREDUMP is not set
# end of Debugging Options

# CONFIG_DISK_ACCESS is not set
# CONFIG_EMUL is not set
# CONFIG_CHARACTER_FRAMEBUFFER is not set

#
# File Systems
#
# CONFIG_FILE_SYSTEM is not set
# CONFIG_FCB is not set
# CONFIG_NVS is not set
# end of File Systems

#
# Inter Processor Communication
#
# CONFIG_RPMSG_SERVICE is not set
# CONFIG_IPC_SERVICE is not set
# end of Inter Processor Communication

# CONFIG_JWT is not set
CONFIG_LOG=y
# CONFIG_LOG_MODE_DEFERRED is not set
CONFIG_LOG_MODE_IMMEDIATE=y
# CONFIG_LOG_MODE_MINIMAL is not set
# CONFIG_LOG_FRONTEND is not set

#
# Logging levels filtering
#
# CONFIG_LOG_RUNTIME_FILTERING is not set
CONFIG_LOG_OVERRIDE_LEVEL=0
CONFIG_LOG_MAX_LEVEL=4
# end of Logging levels filtering

#
# Processing
#
# CONFIG_LOG_PRINTK is not set
CONFIG_LOG_TRACE_SHORT_TIMESTAMP=y
# CONFIG_LOG_TIMESTAMP_64BIT is not set
# end of Processing

#
# Output Formatting
#

#
# Prepend non-hexdump log message with function name
#
# CONFIG_LOG_FUNC_NAME_PREFIX_ERR is not set
# CONFIG_LOG_FUNC_NAME_PREFIX_WRN is not set
# CONFIG_LOG_FUNC_NAME_PREFIX_INF is not set
CONFIG_LOG_FUNC_NAME_PREFIX_DBG=y
# end of Prepend non-hexdump log message with function name

CONFIG_LOG_OUTPUT=y
# CONFIG_LOG_MIPI_SYST_ENABLE is not set
# CONFIG_LOG_IMMEDIATE_CLEAN_OUTPUT is not set
CONFIG_LOG_BACKEND_SHOW_COLOR=y
# CONFIG_LOG_INFO_COLOR_GREEN is not set
CONFIG_LOG_TAG_MAX_LEN=0
CONFIG_LOG_BACKEND_FORMAT_TIMESTAMP=y
# CONFIG_LOG_OUTPUT_FORMAT_LINUX_TIMESTAMP is not set
# end of Output Formatting

#
# Backends
#
CONFIG_LOG_BACKEND_UART=y
CONFIG_LOG_BACKEND_UART_BUFFER_SIZE=1
CONFIG_LOG_BACKEND_UART_OUTPUT_TEXT=y
# CONFIG_LOG_BACKEND_UART_OUTPUT_DICTIONARY is not set
CONFIG_LOG_BACKEND_UART_OUTPUT_DEFAULT=0
# CONFIG_LOG_BACKEND_SWO is not set
CONFIG_LOG_BACKEND_RTT=y
# CONFIG_LOG_BACKEND_RTT_MODE_DROP is not set
CONFIG_LOG_BACKEND_RTT_MODE_BLOCK=y
# CONFIG_LOG_BACKEND_RTT_MODE_OVERWRITE is not set
CONFIG_LOG_BACKEND_RTT_OUTPUT_TEXT=y
# CONFIG_LOG_BACKEND_RTT_OUTPUT_DICTIONARY is not set
CONFIG_LOG_BACKEND_RTT_OUTPUT_DEFAULT=0
CONFIG_LOG_BACKEND_RTT_OUTPUT_BUFFER_SIZE=16
CONFIG_LOG_BACKEND_RTT_RETRY_CNT=4
CONFIG_LOG_BACKEND_RTT_RETRY_DELAY_MS=5
CONFIG_LOG_BACKEND_RTT_BUFFER=0
# end of Backends

#
# Misc
#
CONFIG_LOG_DOMAIN_ID=0
CONFIG_LOG_USE_VLA=y
CONFIG_LOG_ALWAYS_RUNTIME=y
# CONFIG_LOG_FMT_SECTION is not set
# CONFIG_LOG_USE_TAGGED_ARGUMENTS is not set
# end of Misc

#
# Device Management
#

#
# Host command handler subsystem
#
# CONFIG_EC_HOST_CMD is not set
# end of Host command handler subsystem

# CONFIG_MCUMGR is not set
# CONFIG_HAWKBIT is not set
# CONFIG_UPDATEHUB is not set
# CONFIG_OSDP is not set
# end of Device Management

# CONFIG_MODBUS is not set

#
# Networking
#
# CONFIG_NET_BUF is not set
# CONFIG_NETWORKING is not set
# end of Networking

#
# Portability
#
# end of Portability

#
# Power Management
#
# end of Power Management

# CONFIG_SHELL is not set
# CONFIG_STATS is not set
# CONFIG_USB_DEVICE_STACK is not set
# CONFIG_SD_STACK is not set
# CONFIG_IMG_MANAGER is not set

#
# Random Number Generators
#
# CONFIG_TEST_RANDOM_GENERATOR is not set
# end of Random Number Generators

#
# Storage
#
CONFIG_FLASH_MAP=y
# CONFIG_FLASH_AREA_CHECK_INTEGRITY is not set
# CONFIG_STREAM_FLASH is not set
# end of Storage

# CONFIG_SETTINGS is not set
# CONFIG_TASK_WDT is not set

#
# Testing
#
# CONFIG_ZTEST is not set
# CONFIG_ZTEST_MOCKING is not set
# CONFIG_ZTRESS is not set
# CONFIG_TEST is not set
# CONFIG_TEST_USERSPACE is not set
# end of Testing

# CONFIG_TIMING_FUNCTIONS is not set
# CONFIG_TRACING is not set
# CONFIG_RTIO is not set
# end of Sub Systems and OS Services

CONFIG_TOOLCHAIN_ZEPHYR_0_14=y

#
# Build and Link Features
#

#
# Linker Options
#
# CONFIG_LINKER_ORPHAN_SECTION_PLACE is not set
CONFIG_LINKER_ORPHAN_SECTION_WARN=y
# CONFIG_LINKER_ORPHAN_SECTION_ERROR is not set
CONFIG_HAS_FLASH_LOAD_OFFSET=y
CONFIG_USE_DT_CODE_PARTITION=y
CONFIG_FLASH_LOAD_OFFSET=0x0
CONFIG_FLASH_LOAD_SIZE=0xc000
CONFIG_LD_LINKER_SCRIPT_SUPPORTED=y
CONFIG_LD_LINKER_TEMPLATE=y
# CONFIG_CMAKE_LINKER_GENERATOR is not set
# CONFIG_HAVE_CUSTOM_LINKER_SCRIPT is not set
CONFIG_KERNEL_ENTRY="__start"
CONFIG_LINKER_SORT_BY_ALIGNMENT=y
CONFIG_SRAM_OFFSET=0

#
# Linker Sections
#
# CONFIG_LINKER_USE_BOOT_SECTION is not set
# CONFIG_LINKER_USE_PINNED_SECTION is not set
CONFIG_LINKER_GENERIC_SECTIONS_PRESENT_AT_BOOT=y
# end of Linker Sections
# end of Linker Options

#
# Compiler Options
#
# CONFIG_CODING_GUIDELINE_CHECK is not set
# CONFIG_NATIVE_APPLICATION is not set
CONFIG_SIZE_OPTIMIZATIONS=y
# CONFIG_SPEED_OPTIMIZATIONS is not set
# CONFIG_DEBUG_OPTIMIZATIONS is not set
# CONFIG_NO_OPTIMIZATIONS is not set
CONFIG_COMPILER_COLOR_DIAGNOSTICS=y
CONFIG_COMPILER_OPT=""
# CONFIG_MISRA_SANE is not set
# end of Compiler Options

# CONFIG_ASSERT_ON_ERRORS is not set
# CONFIG_NO_RUNTIME_CHECKS is not set
CONFIG_RUNTIME_ERROR_CHECKS=y

#
# Build Options
#
CONFIG_KERNEL_BIN_NAME="zephyr"
CONFIG_OUTPUT_STAT=y
# CONFIG_OUTPUT_SYMBOLS is not set
CONFIG_OUTPUT_DISASSEMBLY=y
# CONFIG_OUTPUT_DISASSEMBLE_ALL is not set
CONFIG_OUTPUT_PRINT_MEMORY_USAGE=y
# CONFIG_CLEANUP_INTERMEDIATE_FILES is not set
# CONFIG_BUILD_NO_GAP_FILL is not set
CONFIG_BUILD_OUTPUT_BIN=y
# CONFIG_BUILD_OUTPUT_EXE is not set
# CONFIG_BUILD_OUTPUT_S19 is not set
# CONFIG_BUILD_OUTPUT_UF2 is not set
# CONFIG_BUILD_OUTPUT_STRIPPED is not set
# CONFIG_BUILD_OUTPUT_INFO_HEADER is not set
# CONFIG_APPLICATION_DEFINED_SYSCALL is not set
# CONFIG_MAKEFILE_EXPORTS is not set
CONFIG_BUILD_OUTPUT_META=y
# CONFIG_BUILD_OUTPUT_META_STATE_PROPAGATE is not set
# end of Build Options

CONFIG_WARN_DEPRECATED=y
CONFIG_ENFORCE_ZEPHYR_STDINT=y
# end of Build and Link Features

#
# Boot Options
#
# CONFIG_IS_BOOTLOADER is not set
# CONFIG_BOOTLOADER_BOSSA is not set
# end of Boot Options

#
# Compatibility
#
CONFIG_COMPAT_INCLUDES=y
# end of Compatibility

CONFIG_LEGACY_INCLUDE_PATH=y

zephyr.dts:

/dts-v1/;

/ {
	#address-cells = < 0x1 >;
	#size-cells = < 0x1 >;
	model = "Nordic nRF52 DK NRF52832";
	compatible = "nordic,nrf52-dk-nrf52832";
	chosen {
		zephyr,entropy = &rng;
		zephyr,flash-controller = &flash_controller;
		zephyr,console = &uart0;
		zephyr,shell-uart = &uart0;
		zephyr,uart-mcumgr = &uart0;
		zephyr,bt-mon-uart = &uart0;
		zephyr,bt-c2h-uart = &uart0;
		zephyr,sram = &sram0;
		zephyr,flash = &flash0;
		zephyr,code-partition = &boot_partition;
		nordic,pm-ext-flash = &at25df041b;
	};
	aliases {
		led0 = &led0;
		led1 = &led1;
		led2 = &led2;
		led3 = &led3;
		pwm-led0 = &pwm_led0;
		sw0 = &button0;
		sw1 = &button1;
		sw2 = &button2;
		sw3 = &button3;
		bootloader-led0 = &led0;
		mcuboot-button0 = &button0;
		mcuboot-led0 = &led0;
		watchdog0 = &wdt0;
	};
	soc {
		#address-cells = < 0x1 >;
		#size-cells = < 0x1 >;
		compatible = "nordic,nRF52832-QFAA", "nordic,nRF52832", "nordic,nRF52", "simple-bus";
		interrupt-parent = < &nvic >;
		ranges;
		nvic: interrupt-controller@e000e100 {
			#address-cells = < 0x1 >;
			compatible = "arm,v7m-nvic";
			reg = < 0xe000e100 0xc00 >;
			interrupt-controller;
			#interrupt-cells = < 0x2 >;
			arm,num-irq-priority-bits = < 0x3 >;
			phandle = < 0x1 >;
		};
		systick: timer@e000e010 {
			compatible = "arm,armv7m-systick";
			reg = < 0xe000e010 0x10 >;
			status = "disabled";
		};
		ficr: ficr@10000000 {
			compatible = "nordic,nrf-ficr";
			reg = < 0x10000000 0x1000 >;
			status = "okay";
		};
		uicr: uicr@10001000 {
			compatible = "nordic,nrf-uicr";
			reg = < 0x10001000 0x1000 >;
			status = "okay";
		};
		sram0: memory@20000000 {
			compatible = "mmio-sram";
			reg = < 0x20000000 0x10000 >;
		};
		clock: clock@40000000 {
			compatible = "nordic,nrf-clock";
			reg = < 0x40000000 0x1000 >;
			interrupts = < 0x0 0x1 >;
			status = "okay";
		};
		power: power@40000000 {
			compatible = "nordic,nrf-power";
			reg = < 0x40000000 0x1000 >;
			interrupts = < 0x0 0x1 >;
			status = "okay";
		};
		bprot: bprot@40000000 {
			compatible = "nordic,nrf-bprot";
			reg = < 0x40000000 0x1000 >;
			status = "okay";
		};
		radio: radio@40001000 {
			compatible = "nordic,nrf-radio";
			reg = < 0x40001000 0x1000 >;
			interrupts = < 0x1 0x1 >;
			status = "okay";
			ble-2mbps-supported;
		};
		uart0: arduino_serial: uart@40002000 {
			compatible = "nordic,nrf-uarte";
			reg = < 0x40002000 0x1000 >;
			interrupts = < 0x2 0x1 >;
			status = "okay";
			current-speed = < 0x1c200 >;
			pinctrl-0 = < &uart0_default >;
			pinctrl-1 = < &uart0_sleep >;
			pinctrl-names = "default", "sleep";
		};
		i2c0: arduino_i2c: i2c@40003000 {
			compatible = "nordic,nrf-twi";
			#address-cells = < 0x1 >;
			#size-cells = < 0x0 >;
			reg = < 0x40003000 0x1000 >;
			clock-frequency = < 0x186a0 >;
			interrupts = < 0x3 0x1 >;
			status = "disabled";
			pinctrl-0 = < &i2c0_default >;
			pinctrl-1 = < &i2c0_sleep >;
			pinctrl-names = "default", "sleep";
		};
		spi0: spi@40003000 {
			compatible = "nordic,nrf-spi";
			#address-cells = < 0x1 >;
			#size-cells = < 0x0 >;
			reg = < 0x40003000 0x1000 >;
			interrupts = < 0x3 0x1 >;
			max-frequency = < 0x7a1200 >;
			status = "okay";
			pinctrl-0 = < &spi0_default_alt >;
			pinctrl-1 = < &spi0_sleep_alt >;
			pinctrl-names = "default", "sleep";
			label = "SPI_0";
			cs-gpios = < &gpio0 0x6 0x1 >;
			at25df041b: at25df041b@0 {
				compatible = "jedec,spi-nor";
				label = "AT25DF041B";
				spi-max-frequency = < 0xf4240 >;
				reg = < 0x0 >;
				jedec-id = [ 1F 44 02 ];
				size = < 0x400000 >;
				has-dpd;
				t-enter-dpd = < 0x2710 >;
				t-exit-dpd = < 0x88b8 >;
				wp-gpios = < &gpio0 0x7 0x1 >;
				hold-gpios = < &gpio0 0xb 0x1 >;
				has-lock = < 0xff >;
			};
		};
		i2c1: i2c@40004000 {
			compatible = "nordic,nrf-twi";
			#address-cells = < 0x1 >;
			#size-cells = < 0x0 >;
			reg = < 0x40004000 0x1000 >;
			clock-frequency = < 0x186a0 >;
			interrupts = < 0x4 0x1 >;
			status = "disabled";
			pinctrl-0 = < &i2c1_default >;
			pinctrl-1 = < &i2c1_sleep >;
			pinctrl-names = "default", "sleep";
		};
		spi1: spi@40004000 {
			compatible = "nordic,nrf-spi";
			#address-cells = < 0x1 >;
			#size-cells = < 0x0 >;
			reg = < 0x40004000 0x1000 >;
			interrupts = < 0x4 0x1 >;
			max-frequency = < 0x7a1200 >;
			status = "okay";
			pinctrl-0 = < &spi1_default_alt >;
			pinctrl-1 = < &spi1_sleep_alt >;
			pinctrl-names = "default", "sleep";
			label = "SPI_1";
			cs-gpios = < &gpio0 0xe 0x1 >;
			adxl362@0 {
				compatible = "adi,adxl362";
				label = "ADXL362";
				spi-max-frequency = < 0x7a1200 >;
				reg = < 0x0 >;
				int1-gpios = < &gpio0 0xc 0x0 >;
			};
		};
		nfct: nfct@40005000 {
			compatible = "nordic,nrf-nfct";
			reg = < 0x40005000 0x1000 >;
			interrupts = < 0x5 0x1 >;
			status = "disabled";
		};
		gpiote: gpiote@40006000 {
			compatible = "nordic,nrf-gpiote";
			reg = < 0x40006000 0x1000 >;
			interrupts = < 0x6 0x5 >;
			status = "okay";
		};
		adc: adc@40007000 {
			compatible = "nordic,nrf-saadc";
			reg = < 0x40007000 0x1000 >;
			interrupts = < 0x7 0x1 >;
			status = "okay";
			#io-channel-cells = < 0x1 >;
			phandle = < 0x13 >;
		};
		timer0: timer@40008000 {
			compatible = "nordic,nrf-timer";
			status = "okay";
			reg = < 0x40008000 0x1000 >;
			cc-num = < 0x4 >;
			interrupts = < 0x8 0x1 >;
			prescaler = < 0x0 >;
		};
		timer1: timer@40009000 {
			compatible = "nordic,nrf-timer";
			status = "okay";
			reg = < 0x40009000 0x1000 >;
			cc-num = < 0x4 >;
			interrupts = < 0x9 0x1 >;
			prescaler = < 0x0 >;
		};
		timer2: timer@4000a000 {
			compatible = "nordic,nrf-timer";
			status = "okay";
			reg = < 0x4000a000 0x1000 >;
			cc-num = < 0x4 >;
			interrupts = < 0xa 0x1 >;
			prescaler = < 0x0 >;
			phandle = < 0x11 >;
		};
		rtc0: rtc@4000b000 {
			compatible = "nordic,nrf-rtc";
			reg = < 0x4000b000 0x1000 >;
			cc-num = < 0x3 >;
			interrupts = < 0xb 0x1 >;
			status = "okay";
			clock-frequency = < 0x8000 >;
			prescaler = < 0x1 >;
		};
		temp: temp@4000c000 {
			compatible = "nordic,nrf-temp";
			reg = < 0x4000c000 0x1000 >;
			interrupts = < 0xc 0x1 >;
			status = "okay";
		};
		rng: random@4000d000 {
			compatible = "nordic,nrf-rng";
			reg = < 0x4000d000 0x1000 >;
			interrupts = < 0xd 0x1 >;
			status = "okay";
		};
		ecb: ecb@4000e000 {
			compatible = "nordic,nrf-ecb";
			reg = < 0x4000e000 0x1000 >;
			interrupts = < 0xe 0x1 >;
			status = "okay";
		};
		ccm: ccm@4000f000 {
			compatible = "nordic,nrf-ccm";
			reg = < 0x4000f000 0x1000 >;
			interrupts = < 0xf 0x1 >;
			length-field-length-8-bits;
			status = "okay";
		};
		wdt: wdt0: watchdog@40010000 {
			compatible = "nordic,nrf-wdt";
			reg = < 0x40010000 0x1000 >;
			interrupts = < 0x10 0x1 >;
			status = "okay";
		};
		rtc1: rtc@40011000 {
			compatible = "nordic,nrf-rtc";
			reg = < 0x40011000 0x1000 >;
			cc-num = < 0x4 >;
			interrupts = < 0x11 0x1 >;
			status = "okay";
			clock-frequency = < 0x8000 >;
			prescaler = < 0x1 >;
		};
		qdec: qdec0: qdec@40012000 {
			compatible = "nordic,nrf-qdec";
			reg = < 0x40012000 0x1000 >;
			interrupts = < 0x12 0x1 >;
			status = "disabled";
		};
		comp: comparator@40013000 {
			compatible = "nordic,nrf-comp";
			reg = < 0x40013000 0x1000 >;
			interrupts = < 0x13 0x1 >;
			status = "disabled";
			#io-channel-cells = < 0x1 >;
		};
		egu0: swi0: egu@40014000 {
			compatible = "nordic,nrf-egu", "nordic,nrf-swi";
			reg = < 0x40014000 0x1000 >;
			interrupts = < 0x14 0x1 >;
			status = "okay";
		};
		egu1: swi1: egu@40015000 {
			compatible = "nordic,nrf-egu", "nordic,nrf-swi";
			reg = < 0x40015000 0x1000 >;
			interrupts = < 0x15 0x1 >;
			status = "okay";
		};
		egu2: swi2: egu@40016000 {
			compatible = "nordic,nrf-egu", "nordic,nrf-swi";
			reg = < 0x40016000 0x1000 >;
			interrupts = < 0x16 0x1 >;
			status = "okay";
		};
		egu3: swi3: egu@40017000 {
			compatible = "nordic,nrf-egu", "nordic,nrf-swi";
			reg = < 0x40017000 0x1000 >;
			interrupts = < 0x17 0x1 >;
			status = "okay";
		};
		egu4: swi4: egu@40018000 {
			compatible = "nordic,nrf-egu", "nordic,nrf-swi";
			reg = < 0x40018000 0x1000 >;
			interrupts = < 0x18 0x1 >;
			status = "okay";
		};
		egu5: swi5: egu@40019000 {
			compatible = "nordic,nrf-egu", "nordic,nrf-swi";
			reg = < 0x40019000 0x1000 >;
			interrupts = < 0x19 0x1 >;
			status = "okay";
		};
		timer3: timer@4001a000 {
			compatible = "nordic,nrf-timer";
			status = "okay";
			reg = < 0x4001a000 0x1000 >;
			cc-num = < 0x6 >;
			interrupts = < 0x1a 0x1 >;
			prescaler = < 0x0 >;
		};
		timer4: timer@4001b000 {
			compatible = "nordic,nrf-timer";
			status = "okay";
			reg = < 0x4001b000 0x1000 >;
			cc-num = < 0x6 >;
			interrupts = < 0x1b 0x1 >;
			prescaler = < 0x0 >;
		};
		pwm0: pwm@4001c000 {
			compatible = "nordic,nrf-pwm";
			reg = < 0x4001c000 0x1000 >;
			interrupts = < 0x1c 0x1 >;
			status = "disabled";
			#pwm-cells = < 0x3 >;
			pinctrl-0 = < &pwm0_default >;
			pinctrl-1 = < &pwm0_sleep >;
			pinctrl-names = "default", "sleep";
			phandle = < 0x12 >;
		};
		pdm0: pdm@4001d000 {
			compatible = "nordic,nrf-pdm";
			reg = < 0x4001d000 0x1000 >;
			interrupts = < 0x1d 0x1 >;
			status = "disabled";
		};
		flash_controller: flash-controller@4001e000 {
			compatible = "nordic,nrf52-flash-controller";
			reg = < 0x4001e000 0x1000 >;
			#address-cells = < 0x1 >;
			#size-cells = < 0x1 >;
			flash0: flash@0 {
				compatible = "soc-nv-flash";
				erase-block-size = < 0x1000 >;
				write-block-size = < 0x4 >;
				reg = < 0x0 0x80000 >;
				partitions {
					compatible = "fixed-partitions";
					#address-cells = < 0x1 >;
					#size-cells = < 0x1 >;
					boot_partition: partition@0 {
						label = "mcuboot";
						reg = < 0x0 0xc000 >;
					};
					slot0_partition: partition@c000 {
						label = "image-0";
						reg = < 0xc000 0x32000 >;
					};
					slot1_partition: partition@3e000 {
						label = "image-1";
						reg = < 0x3e000 0x32000 >;
					};
					scratch_partition: partition@70000 {
						label = "image-scratch";
						reg = < 0x70000 0xa000 >;
					};
					storage_partition: partition@7a000 {
						label = "storage";
						reg = < 0x7a000 0x6000 >;
					};
				};
			};
		};
		ppi: ppi@4001f000 {
			compatible = "nordic,nrf-ppi";
			reg = < 0x4001f000 0x1000 >;
			status = "okay";
		};
		mwu: mwu@40020000 {
			compatible = "nordic,nrf-mwu";
			reg = < 0x40020000 0x1000 >;
			status = "okay";
		};
		pwm1: pwm@40021000 {
			compatible = "nordic,nrf-pwm";
			reg = < 0x40021000 0x1000 >;
			interrupts = < 0x21 0x1 >;
			status = "disabled";
			#pwm-cells = < 0x3 >;
		};
		pwm2: pwm@40022000 {
			compatible = "nordic,nrf-pwm";
			reg = < 0x40022000 0x1000 >;
			interrupts = < 0x22 0x1 >;
			status = "disabled";
			#pwm-cells = < 0x3 >;
		};
		spi2: arduino_spi: spi@40023000 {
			compatible = "nordic,nrf-spi";
			#address-cells = < 0x1 >;
			#size-cells = < 0x0 >;
			reg = < 0x40023000 0x1000 >;
			interrupts = < 0x23 0x1 >;
			max-frequency = < 0x7a1200 >;
			status = "okay";
			cs-gpios = < &gpio0 0x1d 0x1 >;
			pinctrl-0 = < &spi2_default_alt >;
			pinctrl-1 = < &spi2_sleep_alt >;
			pinctrl-names = "default", "sleep";
			label = "SPI_2";
		};
		rtc2: rtc@40024000 {
			compatible = "nordic,nrf-rtc";
			reg = < 0x40024000 0x1000 >;
			cc-num = < 0x4 >;
			interrupts = < 0x24 0x1 >;
			status = "okay";
			clock-frequency = < 0x8000 >;
			prescaler = < 0x1 >;
		};
		i2s0: i2s@40025000 {
			compatible = "nordic,nrf-i2s";
			#address-cells = < 0x1 >;
			#size-cells = < 0x0 >;
			reg = < 0x40025000 0x1000 >;
			interrupts = < 0x25 0x1 >;
			status = "disabled";
		};
		gpio0: gpio@50000000 {
			compatible = "nordic,nrf-gpio";
			gpio-controller;
			reg = < 0x50000000 0x1000 >;
			#gpio-cells = < 0x2 >;
			status = "okay";
			port = < 0x0 >;
			phandle = < 0x8 >;
		};
	};
	pinctrl: pin-controller {
		compatible = "nordic,nrf-pinctrl";
		uart0_default: uart0_default {
			phandle = < 0x2 >;
			group1 {
				psels = < 0x14 >, < 0x10013 >, < 0x20005 >, < 0x30018 >;
			};
		};
		uart0_sleep: uart0_sleep {
			phandle = < 0x3 >;
			group1 {
				psels = < 0x14 >, < 0x10013 >, < 0x20005 >, < 0x30018 >;
				low-power-enable;
			};
		};
		i2c0_default: i2c0_default {
			phandle = < 0x4 >;
			group1 {
				psels = < 0xc001a >, < 0xb001b >;
			};
		};
		i2c0_sleep: i2c0_sleep {
			phandle = < 0x5 >;
			group1 {
				psels = < 0xc001a >, < 0xb001b >;
				low-power-enable;
			};
		};
		i2c1_default: i2c1_default {
			phandle = < 0x9 >;
			group1 {
				psels = < 0xc001e >, < 0xb001f >;
			};
		};
		i2c1_sleep: i2c1_sleep {
			phandle = < 0xa >;
			group1 {
				psels = < 0xc001e >, < 0xb001f >;
				low-power-enable;
			};
		};
		pwm0_default: pwm0_default {
			phandle = < 0xd >;
			group1 {
				psels = < 0x160011 >;
				nordic,invert;
			};
		};
		pwm0_sleep: pwm0_sleep {
			phandle = < 0xe >;
			group1 {
				psels = < 0x160011 >;
				low-power-enable;
			};
		};
		spi0_default: spi0_default {
			group1 {
				psels = < 0x4001b >, < 0x5001a >, < 0x6001c >;
			};
		};
		spi0_sleep: spi0_sleep {
			group1 {
				psels = < 0x4001b >, < 0x5001a >, < 0x6001c >;
				low-power-enable;
			};
		};
		spi1_default: spi1_default {
			group1 {
				psels = < 0x4001f >, < 0x5001e >, < 0x6001d >;
			};
		};
		spi1_sleep: spi1_sleep {
			group1 {
				psels = < 0x4001f >, < 0x5001e >, < 0x6001d >;
				low-power-enable;
			};
		};
		spi2_default: spi2_default {
			group1 {
				psels = < 0x40019 >, < 0x50017 >, < 0x60018 >;
			};
		};
		spi2_sleep: spi2_sleep {
			group1 {
				psels = < 0x40019 >, < 0x50017 >, < 0x60018 >;
				low-power-enable;
			};
		};
		spi0_default_alt: spi0_default_alt {
			phandle = < 0x6 >;
			group1 {
				psels = < 0x40009 >, < 0x5000a >, < 0x60008 >;
			};
		};
		spi0_sleep_alt: spi0_sleep_alt {
			phandle = < 0x7 >;
			group1 {
				psels = < 0x40009 >, < 0x5000a >, < 0x60008 >;
				low-power-enable;
			};
		};
		spi1_default_alt: spi1_default_alt {
			phandle = < 0xb >;
			group1 {
				psels = < 0x40011 >, < 0x50010 >, < 0x6000f >;
			};
		};
		spi1_sleep_alt: spi1_sleep_alt {
			phandle = < 0xc >;
			group1 {
				psels = < 0x40011 >, < 0x50010 >, < 0x6000f >;
				low-power-enable;
			};
		};
		spi2_default_alt: spi2_default_alt {
			phandle = < 0xf >;
			group1 {
				psels = < 0x40019 >, < 0x5001c >, < 0x6001a >;
			};
		};
		spi2_sleep_alt: spi2_sleep_alt {
			phandle = < 0x10 >;
			group1 {
				psels = < 0x40019 >, < 0x5001c >, < 0x6001a >;
				low-power-enable;
			};
		};
	};
	rng_hci: entropy_bt_hci {
		compatible = "zephyr,bt-hci-entropy";
		status = "okay";
	};
	cpus {
		#address-cells = < 0x1 >;
		#size-cells = < 0x0 >;
		cpu@0 {
			device_type = "cpu";
			compatible = "arm,cortex-m4f";
			reg = < 0x0 >;
			#address-cells = < 0x1 >;
			#size-cells = < 0x1 >;
			itm: itm@e0000000 {
				compatible = "arm,armv7m-itm";
				reg = < 0xe0000000 0x1000 >;
				swo-ref-frequency = < 0x1e84800 >;
			};
		};
	};
	sw_pwm: sw-pwm {
		compatible = "nordic,nrf-sw-pwm";
		status = "disabled";
		generator = < &timer2 >;
		clock-prescaler = < 0x0 >;
		#pwm-cells = < 0x3 >;
	};
	leds {
		compatible = "gpio-leds";
		led0: led_0 {
			gpios = < &gpio0 0x11 0x1 >;
			label = "Green LED 0";
		};
		led1: led_1 {
			gpios = < &gpio0 0x12 0x1 >;
			label = "Green LED 1";
		};
		led2: led_2 {
			gpios = < &gpio0 0x13 0x1 >;
			label = "Green LED 2";
		};
		led3: led_3 {
			gpios = < &gpio0 0x14 0x1 >;
			label = "Green LED 3";
		};
	};
	pwmleds {
		compatible = "pwm-leds";
		pwm_led0: pwm_led_0 {
			pwms = < &pwm0 0x0 0x1312d00 0x1 >;
		};
	};
	buttons {
		compatible = "gpio-keys";
		button0: button_0 {
			gpios = < &gpio0 0xd 0x11 >;
			label = "Push button switch 0";
		};
		button1: button_1 {
			gpios = < &gpio0 0xe 0x11 >;
			label = "Push button switch 1";
		};
		button2: button_2 {
			gpios = < &gpio0 0xf 0x11 >;
			label = "Push button switch 2";
		};
		button3: button_3 {
			gpios = < &gpio0 0x10 0x11 >;
			label = "Push button switch 3";
		};
	};
	arduino_header: connector {
		compatible = "arduino-header-r3";
		#gpio-cells = < 0x2 >;
		gpio-map-mask = < 0xffffffff 0xffffffc0 >;
		gpio-map-pass-thru = < 0x0 0x3f >;
		gpio-map = < 0x0 0x0 &gpio0 0x3 0x0 >, < 0x1 0x0 &gpio0 0x4 0x0 >, < 0x2 0x0 &gpio0 0x1c 0x0 >, < 0x3 0x0 &gpio0 0x1d 0x0 >, < 0x4 0x0 &gpio0 0x1e 0x0 >, < 0x5 0x0 &gpio0 0x1f 0x0 >, < 0x6 0x0 &gpio0 0xb 0x0 >, < 0x7 0x0 &gpio0 0xc 0x0 >, < 0x8 0x0 &gpio0 0xd 0x0 >, < 0x9 0x0 &gpio0 0xe 0x0 >, < 0xa 0x0 &gpio0 0xf 0x0 >, < 0xb 0x0 &gpio0 0x10 0x0 >, < 0xc 0x0 &gpio0 0x11 0x0 >, < 0xd 0x0 &gpio0 0x12 0x0 >, < 0xe 0x0 &gpio0 0x13 0x0 >, < 0xf 0x0 &gpio0 0x14 0x0 >, < 0x10 0x0 &gpio0 0x16 0x0 >, < 0x11 0x0 &gpio0 0x17 0x0 >, < 0x12 0x0 &gpio0 0x18 0x0 >, < 0x13 0x0 &gpio0 0x19 0x0 >, < 0x14 0x0 &gpio0 0x1a 0x0 >, < 0x15 0x0 &gpio0 0x1b 0x0 >;
	};
	arduino_adc: analog-connector {
		compatible = "arduino,uno-adc";
		#io-channel-cells = < 0x1 >;
		io-channel-map = < 0x0 &adc 0x1 >, < 0x1 &adc 0x2 >, < 0x2 &adc 0x4 >, < 0x3 &adc 0x5 >, < 0x4 &adc 0x6 >, < 0x5 &adc 0x7 >;
	};
	zephyr,user {
		io-channels = < &adc 0x1 >, < &adc 0x3 >;
	};
};

RE: MCUBoot SPI Flash Image

Håkon Alseth — Mon, 09 Jan 2023 08:13:58 GMT

Hi,

You are using the NFC pins as GPIOs, and setting the appropriate configs, and the main application is able to successfully read/write to the flash, so that should be in order.

The BOOT_MAX_IMG_SECTORS is given in 4k blocks (flash page alignment), so 116 should be enough for a size of 0x74000. The warning printed is a catch-all message, indicating that there's a generic error in the communication in the mcuboot child image.

Could you share your build-folder/mcuboot/zephyr/.config and build-folder/mcuboot/zephyr/zephyr.dts file?

Kind regards,

Håkon