Can´t pair again after disconnection

RE: Can´t pair again after disconnection

Joao Dullius — Tue, 10 Jan 2023 10:48:46 GMT

Thanks for all the explanations!

RE: Can´t pair again after disconnection

Einar Thorsrud — Fri, 06 Jan 2023 08:14:53 GMT

Hi,

You always need to call settings_load() after reset when using settings. This is also the case when using CONFIG_BT_SETTINGS=y, as described in the documentation.

RE: Can´t pair again after disconnection

Joao Dullius — Thu, 05 Jan 2023 18:10:00 GMT

Hi Einar,

Thanks. I think I has a misconception on pairing vs bonding, but now it is clear.

I was able to solve the reconnecting issue in two ways:

1) By only using pairing, but not bonding.

The CONFIG_BT_BONDABLE=n did the trick to force the central to restart the pairing every time the peripheral reconnects.

2) By using bonding:

I modified the peripheral, and added the following in prj.conf:

#Enable to Save BLE Settings

CONFIG_BT_SETTINGS=y

CONFIG_FLASH=y

CONFIG_FLASH_PAGE_LAYOUT=y

CONFIG_FLASH_MAP=y

CONFIG_NVS=y

CONFIG_SETTINGS=y

And on my main.c I did:

if (IS_ENABLED(CONFIG_SETTINGS)) {

settings_load();

}

Question: On this (2) scenario, do I need to do the CONDIF_SETTINGS and the settings_load(), or would CONFIG_BT_SETTINGS=y be enough?

RE: Can´t pair again after disconnection

Einar Thorsrud — Wed, 04 Jan 2023 15:09:01 GMT

Hi,

[quote user="Joao Dullius"]Based on that, can we assume the issue is on the central side? [/quote]

Not necessarily. Are you only pairing (establishing a single encrypted session), or are you bonding as well (where the keys should be used for consecutive connections)? If you are only pairing, it wold seem the central is in error (as it looks like it has kept the bonding information). But if you are bonding, the issue seems to be with the peripheral, as it should keep the bonding information and use that the next time.

[quote user="Joao Dullius"]Is there anyway to do the opposite from CONFIG_BT_SMP_ALLOW_UNAUTH_OVERWRITE=y, and force the central to do the bonding from scratch, doing all the .password_entry on both sides again?[/quote]

If you want to do that on every connection, then simply don't bond (but pair). If you never want to bond, add CONFIG_BT_BONDABLE=n to your prj.conf.

RE: Can´t pair again after disconnection

Joao Dullius — Tue, 03 Jan 2023 16:06:16 GMT

Hi Einar, thanks for the quick response.

I'm pairing using fixed passwords sent in .passkey_entry callback.

I did some additional testing:

1) When paired, if I only reset the peripheral, the central gets the error code (2) when trying to pair again.

2) When paired, if I erase the peripheral memory (recover board) and reprogram it, I get error code (2) also.

3) When paired, if I reset the central, when it goes live again the devices will re-pair properly by .passkey_entry callbacks.

Based on that, can we assume the issue is on the central side? When the peripheral resets, the central thinks it will get back live with the previous bonding settings, which is not the case.

Is there anyway to do the opposite from CONFIG_BT_SMP_ALLOW_UNAUTH_OVERWRITE=y, and force the central to do the bonding from scratch, doing all the .password_entry on both sides again?

RE: Can´t pair again after disconnection

Einar Thorsrud — Tue, 03 Jan 2023 14:41:42 GMT

Hi,

The error code (2) is BT_SECURITY_ERR_PIN_OR_KEY_MISSING. Is the slave just reset or is the flash erased (or at least the bonding info)? If so, that could explain the error. And in that case, the fix would be either to not delete the bonding info on the peer, or add CONFIG_BT_SMP_ALLOW_UNAUTH_OVERWRITE=y to allow repairing in case the peer has lost the bonding information (this is not without down-sides though, as it would allow an attacker to replace an existing bond with by spoofing the peer address and pairing).