I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Hi,
I am working on bootloader_secure example on SDK_12.1.0 and set APP_ADV_TIMEOUT_IN_SECONDS to 180 to stop the advertising after 3 mins.
All looks fine and device...
In tihs video , and others this guy has done, the transmission speed of the nRF24L01 2.4G module only achieves a speed of, at best, about 300 packets per second (where a packet...
We are using nrf51822ab, s130, pca10028. After dumping the soft device the free space left is 20kB, my code size is 48kB. I am able to dump the code into device but its not...
I am following ble_peripheral example of nrf51822 SDK 8.0. I have found ble_gatts_char_md_t , ble_gatts_attr_md_t and ble_gatts_attr_t confusing. I want to know the difference...
Hi,
I'm currently using an application that needs a very speed detection of GPIO and need to use NMI on GPIOTE.
I tryed to find how can I connect my NMI to GPIOTE but...
nrf_drv_usbd_init() calls nrf_drv_clock_hfclk_request(NULL)
however nrf_drv_usbd_uninit() calls nrf_drv_clock_lfclk_release();
Is this correct?? If so why?
Hi, I have the opportunity to bid for some research funding for my project, and I'm thinking of speccing a workstation for processing video in realtime, and sensor data in...
I am trying to add the heart_rate_meas function to the ble_app_uart project.
Is this plan possible?
However, it does not go well.
Why are you concerned with this method...
Hey Guys,
im working on some sort of application transport layer for ble and have some questions to better plan what i need and what is kind of redundant.
Is it correct...
Hello everyone,
I am using nrf52832 with SDK version 11.0 for an IoT application. I am communicating with Atmel ATWINC 1500 module through SPI in order to connect to Wifi...
I'm using nrf52 with SDK version 12.0.0. I'm trying to use the FDS for my application. I used one of the existing fds example from link fds_example .
With this example...
Hello,
I am a bit lost, after concluding the application part of my project I try to approach the ble part.
I read the "Getting started with bluetooth low energy " and...
Press down PWRON1 give rise to Q2 and Q3 conduction, the 51822mcu power on and IO send a hight level to PWRON,to keep VCC_nRF.
At this time press a lot of button will not...
