Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Our application is a smartband based on nRF 51822 with SDK 9.0 S130, and we found that the device will stop advertising unexpectedly (application is still alive). We have...
Looking at the radio section of the nrf52832 data sheet I see that in section 21.1.2 Packet configuration it is stated that
"For all modes that can be specified in the MODE...
Hi everyone,
Just a brief introduction about my system, I am currently working on Brain computer Interface which was funded by NSF. In our system we have Sense electronics...
hello there , i have put my nrf51 dk in system off mode.then i am generating interrupt using button 3 to wake up it. but my nrf51dk can't wake up. can you hel p me??
my...
Hello.
I use nRF52 DK, S132v2 and PCA10040.
I want to get timestamp like GetTickCount of C++.
When I searched Documentation, I found RTC what can do like GetTickCount...
Hi,
When I finish coding, I can generate .HEX file for all products. But for real mass production, I may need to flash a seperate serial number in somewhere for each PCBA...
I'm trying to transfer a txt file by sending it from a terminal to my NRF52 DK with the BLE_UART example. I always get a BLE_ERROR_NO_TX_PACKETS avter a few packets though...
Hello, everybody. We have a custom board with nRF51288. We also have code based on ble_template that is working on Nordic devboard and dongle. Code is also working on our...
I am having difficulties porting the SPI Master demo to an S130 Soft Device on SDK 11.0.0. From the looks of it, there seem to be some issues with interrupts but I am unsure...
Using S130,
Central device,
Manual whitelist,
custom hardware.
Manual connection to 1 or 2 peripherals depending on a switch position.
This device is a central that...
hello there . i want to do something like when i press button advertisement starts. when i release button advertisement stops. can anyone tell me how to do this?? any sample...
Looking at Table 40 in the nRF51 Series Reference Manual v3.0, the Memory Protection Unit prevents request sources in Code R1 from writing to RAM R0. But if the request source...
I am facing the below issue that no source is available for "0xffffffff" when i try to debug the program using eclipse
I am using softdevice s110 and have flashed the...
Hi, I developed a sensory application which works together with the Master Control Panel (3.6.0.8331).
On the sensor side I am using the S110 (7.0.0-3.alpha) in combination...
Hi all,
i want a security check on connection that permits only to users that have a password to connect to my peripheral device and, particularly, to read/write on services...
