Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi Team,
Hope you are doing well, and safe from this pandemic.
I would like to ask that, is there any serialization for zigbee from linux PC?
As we have verified...
Hello,
I noticed in the release notes for nRF Connect SDK v1.2.0 there is a known issue with the nrf_send function as it relates to blocking for several minutes, see below...
Hi,
We have successfully verified "BLE UART and Zigbee Color Dimmer Light Switch Example".
Right now we see there is no support for receiving reports from light bulb example...
Hi,
I recently discovered the platform. I'm trying to modify the examples in order to understand the different ways it works.
My last step was to add a Generic On Off...
Hi , I am compiling the bmdware project (in IAR embedded workbench 8.32.2) and I have errors (particularly Errors while linking assembler, shown below).
I have modified...
Hello,
I am using Segger Embedded Studio version 4.52b and when creating a new project, it automatically creates a segger link script file and sets the linker to 'Segger...
Earlier with SDK 13 in custom advertisement I was able to send 30 bytes under unknown characteristics tab in Nrf connect APP but in SDK 15 I am not. Because the firmware or...
Hi everyone,
I started working on the nRF9160 with a Thingy91. I installed nRF Connect SDK v1.2.0 and i was able to try some sample like GPS or AT_client. However I would...
Hi ,
SDK : 16.0.0.,Mesh V4.0 ,PCA10040
My project requirement is : I need to use 2 dev kits one as a server and one as a client communicating each other on BLE Mesh
...
Hello, I'm setting up a mesh network with low consumption sensors and I'm using the Low power node example. I'm having trouble increasing the number of devices supported by...
Hello,
How can I directly read out the POFCON register value on the Watch Window while debugging?
Where is it actually located in the library(sdk 14.2) source code?...
How can i know how much time the microcontroller spends in the timer_event_handler() function? I am fear that i have written down to much code into that function. Regards
Hello,
I have the following statement in flash_placement.xml:
<ProgramSection alignment="4" keep="Yes" load="Yes" name=".nrf_queue" inputsections="*(.nrf_queue*)" address_symbol...
Hello.
I have two nRF52832 (central and peripheral). Connect the central and peripheral and call sd_ble_gap_rssi_get() on the central to get the RSSI and channel. The attached...
Hello there!
At this stage of the product development cycle, we would like to be able just to take simple reading from ADP536x module (to read either battery percentage...
