Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
tldr; read the release notes first and use the batch file provided in the folder
Hi,
I'm trying to load the S110 v7 on an nRF51822QFABB00 and I'm getting the following...
Hi,
I am developing a multi-protocol communication device using BLE, ANT and 868Mhz "long-range" communication. I am using MRF49XA chip for sub-ghz communication. I have...
I have just updated to the latest SDK, including the S110 Soft device v7.0.0.
I have now noticed that I can bond using the Master Control Panel, but I cannot bond using...
On June 25th I asked a private question regarding be able to use the S110 soft device with the nRF51422. The following is the response I got:
....
Yes you can use the...
I am unable to to send notification for a customized service. I am testing a customized services that simply increments a variable every 3 seconds and sends notification with...
Hi guys,
I am trying to use the timer 1 on the nrf51822. I found the sample code online which could probably do the job for me. But I wanted to know what is the standard...
Hey Guys,
i asked this question already few days ago, but today i produced a log-file.
The procedure was:
Setup: SDKv6.0, SoftDevice v7.0.0, nrf51822
empty board...
Hi guys,
I had look at the ble_connectivity example in \nrf51822\Board\nrf6310\s110\ble_connectivity floader,but I can't found any documentation about this project.Is it...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
We found that in some cases. e.g. we started a background ble service. The ancs characteristics will change as the picture below. Do you think it's normal? Does the Nordic...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi guys,
i'm just porting my app from SDK5.2+SDv6.0.0 to SDK6.0+SDv7.0.0 and stuck with the device manager. There rises some questions, and i hope someone can help me....
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
Hello,
About TWI in "nRF51_Reference_manual_v1.1.pdf",there is a register called "SHORTS".
I have a few question about this register:
Can I use SHORTS register to...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
