Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I'm trying to understand how to handle error codes from the twi driver at the moment. When I hold my I2C slave in reset and try to configure it nrf_drv_twi_tx() returns 0x8201...
Hello,
in the electrical specification of the Timer peripheral (in the product specification page of the nrf52840 or nrf52832) it is said that there is 0.25us of delay between...
I have created a whitelist in nrf51822 device its working fine. But i stored whitelist details (pp_irk and pp_addr) to an external flash memory( bacause i not using peer manager...
I'm wondering if the extended advertisement feature of Bluetooth 5.0 is supported in any softdevice. If not, when can we expect it to be supported? Still within 2017 (as I...
Hi,
Each node has some state which should be saved in case of a power failure and recovered after it.
The problems:
how to detect the power failure?
where to save...
I have some Bluetooth LE v4.2 beacons that I will connect ONLY with known devices that we may call "readers". No consumer with use my beacons, I program them, I install them...
Hello everyone,
I am currently working on porting the InvenSense motion driver 6.12 to nrf52840pdk.
I followed porting guide provided by InvenSense. However, I met the...
First of all, I know the difference between the two roles, and I have also read through docs.
My question is actually limited to the current nordic mesh implementation....
I need a bootloader that I can use for my application that doesn't use a soft device and allows the firmware to be transferred through uart. Going through the forums, I found...
Common situation:
We have flashed dfu bootloader, and firmware uploaded into Flash via DFU. In this situation, DFU settings page contains correct CRC value for existing...
Because if there is, I'm not seeing it. It seems to me that the SDKv14 has asks you where you want your event handler function like this:
Where spi_0_event_handler() is...
HI,
I have been trying to generate the hex files for the mesh sdk (Latest) examples using cmake following the instructions in the documentation.
But the platforms supported...
Hi All,
I am starting an application using nRF51822 beacon kit.
I have some observation regarding current consumption.
1- erase entire flash and power up only, i can...
I'm trying to measure the startup time of the 32 MHz XTAL at the pins XC1 and XC2. Often a microcontroller will indicate in a register that the XTAL and internal PLL are stable...
