RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Issue is related to:
devzone.nordicsemi.com/.../
Now I use latest SD S130_1.0
So, I added to my service characteristic with notifications enabled. But during discovering...
Hello,
I have a development kit with the PCA10000 and I can comunicate with the PCA10004 for about 5/6 meters what is ok for my application but now I want to comunicate...
Recently I needed to add some functionality, so the software could monitor when there was a ble gatt read characteristic event.
In the addCharacteristic code I simply set...
Hi, We have used nRF51 DK for developing an application where we used USB to load/flash the program code. Now we are in Pre-production stage where we can use only the nRF51422...
Hi,
I would like to extend the HTS service with measurement interval setting support. Bluetooth SIG specifies the measurement interval characteristic, which is easy to...
I'm using the example ble_app_hrs along with the HRM part of the nRF Toolbox iOS app . It makes sense to handle this in on_ble_evt in main.c but am unclear how I can recover...
Hi Team,
I am testing UART on nRF51 DK kit.
I have flashed uart_pca10028 .
I have taken out jumpers from P0.9(TX), P0.11(RX) and GND and connected to PC com port.
...
I have the example app working nicely now, so I want to export the project to a zip or something, effectively copy it, and put it elsewhere in my filesystem and work with...
Hi,
I tried installing the kernel (raspbian-kernel-zip Raspbian kernel for Raspberry Pi 3.17.4 ) on a Raspberry Pi 2 (Model B 1 GB). I found out that the Pi doesn't boot...
I'm trying the multilink central example with s120 and SDK 7.2 (because of simple_uart).
However, my PCA10028 board gets stuck at this macro:
SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_RC_250_PPM_8000MS_CALIBRATION...
My code is attached but essentially it is saying that SPI_MASTER_0 is not defined when I compile. I have the line:
#define SPI_MASTER_0_ENABLE /**< Enable SPI_MASTER_0...
I'm trying to get the ble_app_hrs working on PCA100001, the software installation is brand new (all installed today). I modified the pca100028 ble_app_hrs to try work with...
Hello everyone,
I have problems with my nRF51822. I think it is related to the starting memory address of softdevice. I attach 2 nRFgo's screenshots.
I have programmed...
Hello all,
my question is related to notifications and to maximize data bandwidth using them;
First af all i have already read this: devzone.nordicsemi.com/.../ but it is...
