Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
Hi,
i am using ble_app_template and i added the file "ble_lbs.h" in the main file. Also added this code in the services_init method
uint32_t err_code;
ble_lbs_init_t...
Hello
I've been experiencing an unusual problem using the TWI/I2C library for the nRF51-DK board. Basically, I found that I need to shift my device address to the left...
Hi guys,
I have followed devzone.nordicsemi.com/.../ to set up CrossWorks. Even though I got pass the ble_stack_init();, I still can't discover the device for some reasons...
Hi
Please tell me someone me how to start nRF51822 & softdevice8.0.0
I build a NRF51822 application in gcc & ECLIPSE.
When to run the program, it crashes in the boot...
I'm having a problem adding the GPIOTE_IRQhandler() to my main.c file (see attached). I'm getting a compiler error that it is doubly defined in app_gpiote.o and main.o, but...
is it possible to update the pca20006 (rev. 1.2.0 2015.06) beacon with the pca10000 over DFU?
When i tried to update it with my application written for an older version ...
Hi folks,
I'm using the ble_app_template on a custom board. The BSP has a bunch of stuff I don't need, so I would prefer to not use it and handle my I/O directly instead...
i was going through TWI initialization process here i am confused why have we disabled Blocking mode. The reason for Disabling TWI_BlOCKING_DISABLED
I am referring the below...
hi , i want to modify the "transmitter_pca10028" and "receiver_pca10028" examples in SDK to obtain a transmitter/receiver in the same time (tranceiver). So someone have idea...
Hello, I am using the nrf51822EK and I want to combine the ADC and LPCOMP although in the reference manual it says they can not be used at the same time. Is it possible to...
Hi all,
I met one strange thing on SPI interrupt:
when 51822 advertising, the SPI write and read works well;
But, when CONNECTED, with BLE_GAP_EVT_CONNECTED event occured...
Hello,
I migrated my project from softdevice S110 7.1.0 on a nRF51422 FAC to softdevice S110 8.0.0 and an nRF51822 FAA G3. My code used to have a current consumption around...
Hello everyone,
I'm currently using and modifying the experimental_ble_app_uart. I've seen that for sending characters resp commands the file simple_get_uart is used. My...
