HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
I find this function.
tx
void ble_send(uint8_t * data, uint8_t length)
{
ble_nus_send_string(&m_nus, data,length);
}
ble_send(&data_array[0],10);
but I don...
Hi, I'm trying to run ESB during the timeslot api requested slots.
The problem is that BLE uses app_timer, which uses SWI0 for the callbacks, and at the same time, ESB also...
Hey , I am working on nordic nRF51822 chip and using it as an iBeacon. I want to send some custom data apart from UUID,major,minor in the packet. How can I send it ?
As in...
When I try to set a breakpoint in eclipse by clicking on a line, gdb tells me in the eclipse "Console" window below the code: "No symbol table is loaded. Use the "file" command...
Hello,
I have three custom services. I wanted to add descriptions to the characteristics for easier testing and debug, so I used the typical method to add descriptions...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi
I'm trying to test UART over BLE using the nRF51-DK and the sample code "ble_app_uart_s110_pca10028 (nRF51 PCA10028)" along with both the nRF UART APP for both Android...
I'm using nRF51822 SoC , is it possible to change the major value when i push the button ? I tried simple assignment but it didn't work so i ask if i have to use the function...
hi,
i have kept RAM block 0 and RAM block 1 on in OFF mode by calling "sd_power_ramon_set(0xf000f)" before entering off mode ,i saw the value of RAMON register is 0x00030003...
I'm using nRF51822 SoC . I wanna read and write from the flash memory . Shall I use a specific configuration before using read and write functions provided from S110 softDevice...
we have created ble mesh, and data through ble nodes is passed every 5 seconds, but nodes gets disconnected with reason BLE_HCI_CONN_FAILED_TO_BE_ESTABLISHED??
please someone...
we have created ble mesh, and data through ble nodes is passed every 5 seconds, but nodes gets disconnected with reason BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION??
please...
we have created ble mesh, and data through ble nodes is passed every 5 seconds, but nodes gets disconnected with reason BLE_HCI_CONNECTION_TIMEOUT?
please someone give...
we have created ble mesh, and data through ble nodes is passed every 5 seconds, but nodes gets disconnected with reason BLE_HCI_LOCAL_HOST_TERMINATED_CONNECTION?
please...
