HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi!
Is there any configuration differences between those 2 modules??
I understand from the data sheets that the pinout is just the same.
I´m testing a PA+LNA on the same...
bnjr, je veut mesurer le rssi entre deux composantes BLE Nano . quels son les fichiers .h qu'ils faut ajouter pour le faire fonctionner ?
merci a l'avance
NB : j'utilise...
I tried to program the beacon kit with the nfr51822_beacon_app.hex through DFU-OTA using the nRF Toolbox on an IPad, and though the upload seemed to work, the application...
How do I configure nRFgo to use the IAR I-jet rather than a segger? When I run nRFgo the nRF51 Programming tab is greyed out and it says no board connected. I presume this...
Hello, I use two nRF24L01+ modules as a transmitter and a receiver, and Atmega8515 as my microprocessors. The transmitter seems to be working as I can see the modulation on...
Hi,
Our manufacturer would like to change the recommended capacitors on the nRF51822 antenna circuit design. Here is the query:
Please check below 3 capacitors request...
I notice in the datasheet for the NRF24L01+ that the receive address needs to be programmed into the Receiver.
Our application receives data from another channel and supplies...
Hi All,
I am looking for a cost effective Chip Socket for nRF51822. The challenge with nRF51822 is that while it is the standard QFN48 package, the pitch is 0.4mm making...
hello,
I have known that Nordic has produced new nRF51 DK which already support s130. But it seems only a demo!
What's the exactly plan of BLE 4.1 and 4.2?
When can buy...
Since windows xp isn't supported any more, I need to get the evaluation kit working with a windows 7 PC. It looks like the problem is with the USB communication. Is there...
Hello,
I am using ESB protocol and there is a definition says "#define NRF_ESB_CONST_MAX_TOTAL_PACKETS 6" so how can I use maximum total packets number? I am looking higher...
How do I configure nRFgo to use the IAR I-jet rather than a segger? When I run nRFgo the nRF51 Programming tab is greyed out and it says no board connected. I presume this...
I am using SD 8.0 SDK 8.0 and MCP 3.8 I am able to find the DFUtarg service and successfully complete the transfer of my applcation (100% complete). However, upon finishing...
