Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
I'm looking at designing my own Bluetooth Receiver essentially. Playing music from my phone to a Bluetooth receiver, to output via AUX.
I was looking at the range of MCU...
Hi,
For my all DFU i follow the steps on the Getting started guide , just in the Performing DFU step i use the nrfutil tool for the over USB.
First i tried with the DFU...
Hi team,
Similar to how we have recommendations to use certain pins for low drive, low frequency on the nRF52 series, do we have those recommendations available for the...
nRF connect is not recognizing my nRF9160 board when I try to use the programmer tool. It allow me to select it from 'select device' drop down menu. But then I select it all...
Hi,
I am working with NRF52832 boards where on one board i have loaded Multilink central example, and on the other i have loaded peripheral code with some modifications...
I have merged Light and DFU examples(Light_DFU), and test DFU update both blinky and Light_DFU.
It is always getting ERROR_BUSY (134) while update Light_DFU, but success...
Hi, do you have a schematic / diagram that shows the architecture of the asset tracker application / nRF Cloud?
Does it use MQTT for communication?
Does it use the AWS...
Hi there. I'm developing an NRF52840 project from scratch and wanted to obtain a "good reference" sdkconfig.h . I tried picking one from the examples (the UART example, 'cos...
Hello guys I am using nrf52832 dongle for development and my client has nrf52832 DK at the moment. I have completed my firmware that get ADC values and store data on SD card...
So, we have a problem that the new Samsung S20+ phone is not able to connect to the nRF52833 if extended advertising is enabled (using nRF Connect for Mobile app).
The phone...
Hi,
I am using
nRF52840
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
I am using app_timer to control the LED On time.
the app_timer...
Hi,
I am using nrf sniffer. I have used both nrf51422 and nrf52832. Here I am facing such kind of issue like. Once I am saving my report in wireshark and starting sniffing...
Dear all,
I'm using nRF52810, I want to achieve low power consumption(<200uA). I have disabled easyDMA. Right now I want to know how to turn on/off uart anytime we wish...
