Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
Hi I use SDK 12.3 and sdk 2.0.1 , and set a device name length is 21 like "1234567890ABCDEFGHIJK" by sd_ble_gap_device_name_set;
but in the advertise data the name length...
Hi,
we are developing and application on iOS which can among others, update our hardware over the air, and we found out that e.g. after bootloader update is done, then...
Our hardware has an externa memory connected to the nRF51 by SPI, we also use DFU to update the firmware creating the zip pack (We have buttonless dfu working as well) and...
I've been using the nRF52832 chip for over a year and it works great. However, for a new project I designed a board so that the nRF52 chip was the slave on a SPI bus, and...
Hi,
I just try DFU function in sd130/sdk12.3 and it does work very well.
I did:
(1).Generating your own key:
nrfutil.exe keys generate priv.pem
(2).Display a public...
In the example code, I found this:
#define SERVER_COUNT (3)
#define CLIENT_COUNT (SERVER_COUNT + 1)
I'm having 2 boards (maybe extremely problematic) and I want to...
I have seen at least one person here who has gotten Nordic's UART-over-BLE example app running on the nRF8001. How was that done? Where is it? This example app is not included...
Screenshot of what I'm doing:
So I reset the nRF8001, then try to initiate a transfer by pulling REQN low. However, nRF8001 never responds by pulling RDYN low. I have...
I'm using nRF5DK PCA10040.
And, working on nrf5_SDK_for_Mesh_v0.9.2-Alpha.
I need to enable both of Bluetooth mesh stack and BLE stack.
mesh stack for mesh communication...
I added uart service ( here and here )
and I think in part of ble everything goes well. I have blinking led1 and can see all my services.
Then I tried add uart part.
After...
I have a custom board that has a nRF52832 device (receiver).
I am scanning for remote beacons (also custom boards with nRF82832).
The result is that I obtain the MAC of...
Hi I use 4 characteristics in peripheral and central. When I write to one of the characteristics in the peripheral, I read it using sd_ble_gattc_read in the central. But,...
Hi,
SDK14.0
nRF52832
I am using the dfu\bootloader_secure_ble example as my starting point. My goal is to create a very simple bootloader (with none of the dfu stuff...
