I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
I tried code like
static void on_ble_evt(ble_evt_t * p_ble_evt)
{
....
case BLE_GAP_EVT_TIMEOUT:
if (p_ble_evt->evt.gap_evt.params.timeout.src == BLE_GAP_TIMEOUT_SRC_ADVERTISEMENT...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am unable to compile this to fit into the allocated bootloader space.
Has anyone been able to compile this patched version of the signlebankdfu-ble
with nrf sdk v6 so...
I'm using API 2.1.3, and after several connections/disconnections with a peer device, I'm seeing the API never returning from a DiscoverPipes() call. It appears to be waiting...
Hi,
I'm using nrf51 BLE driver with usb dongle to create test application on PC which simulates
the peripheral.
My problem is I cannot add 128-bit UUID for custom service...
After some pstorage_update calls I start to get error 9. From nrf_error.h it is called NRF_ERROR_INVALID_LENGTH but from SDK doc it looks like pstorage_update does not have...
My question is in regards to BLE security. I have certain characteristics that I want to remain open. As they will be used to determine authentication at the application level...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Working through a custom security implementation. It is to desirable to know a unique identifier for each bond that has been made with the nrf51822 SD. When the SD enters...
I have several asynchronous аperiodic sensors with their interrupt handlers. My service should gather the data from those sensors and do some math. The outcome of this math...
Dear all,
I tried to program and test the iBeacon application on the s110 folder from nordic examples.
The code on the Cortex-M0 has problem. Seems during programming...
After program nrf51822,it works normaly.But when I program again,it can't debug.NO SWD and NO USB DEVICE.So I can't use nrfGoStudio or nrfjprog.exe to recover it.When I pull...
Hi,
I've set up a streaming solution that is easily streaming 4+kBytes/s to an iPhone. I've also set up an ADC service that is sampling at 2,083 Hz 10 bit mode, using a...
Hi,
I am using nrf51822 (128k).
Softdevice 6.0 (s110), SDK 5.2.
How can I send an empty notification packet (data length 0) to master device?
If I send a packet with data...
