Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Dear all,
we're at the pre-production stage, I would like to ask here in the forum the suggestion and/or your experience with fabs in Europe.
What we are looking for...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi all
I’m trying to use the OTA DFU with nrf51422 SDK 6.0 and softdevice s310 V1.0.0. I were supposed to use the nrf tool application for android, but I can’t make it...
Hi
I added some random data under scanned Response as manufacture specific data .Iam using NRF_sniffer & wire shark to view the advertising packets.But in wireshark i couldnt...
Hi All,
We am trying to check and interface Nordic's EMK with custom board running android kitkat.
Problem is we cannot access internet/play store from custom board...
Hi,
I'm using nRF51 BLE driver on PC to simulate BLE peripheral using PCA10000 v2.2 dongle.
I need to add some functionality to the default connectivity app. So I compiled...
Hi, and thanks for reading this.
I attached additional LED to nRF51822 p0.24
however I can not find how to handle it .
if I want to use this function
nrf_gpio_pin_set...
Hey.
Hope this was not asked before. At least I did not find it.
I'm trying the ble_app_hrs_c on s120. Got it to build with gcc (d'oh) and got the serial logging to...
I want to make a robot that can track the direction of the transmitter that is controlling it, for example to aim a camera at the transmitter. The robot vehicle will be controlled...
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi!
Maybe I'm doing something wrong (very possible), but for example, when I want to store array of 3 uint8_t values I use:
uint8_t dataToStore[3];
dataToStore[0] ...
Device: nRF51822 Rev G0
SDK: v5.2.0
Code: raw.githubusercontent.com/.../twi_hw_master.c
Basically, the TWI driver which uses PPI channels (sd_ppi_*) works perfectly...
Hello,
I am using a nrf51422 development kit with softdevice S310 and I have a problem in whatever pin I choose as output when I use the bluetooth.
I run the example...
