the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I'm using the buttonless DFU bootloader examples with bonding and the PC nrfutil with a nRF52840 PDK for the firmware upload.
If I try to start the DFU process...
I'm running SDK 14.0.0 and notice in the examples/flashwrite, the very last flash page is chosen as the place to write data to. Are there any caveats to that? WIll this location...
Hi, everyone. Long time no see.
I wonder if there is a free IDE which is official recommended. As we know that Keil and IAR are all commerical software. GCC command line...
Hello everyone,
As we know the proxy protocol is defined to include BLE devices in a mesh network. But as per my understanding there has to be made some changes in the...
Hello,
I am using nRF52840 PCA10056 DK i want to make my board as central device and scan for all nearby ble devices and display it's device id on terminal connected via...
Using SCAN_INTERVAL and SCAN_WINDOW at 1600 vill make the flash write and erase come out with a error, the fstorage is working fine before the SD is initialised.
/** @brief...
Hi,
I am using the secure bootloader as a template and I want to use the inactivity timeout to shutdown after 10 minutes.
I saw that the limit should be 60000000 ms (according...
SDK: nRF5 SDK for Thread and Zigbee 1.0.0
I have code for the SAADC based on the Low Power SAADC example here .
I have modified it to sample 4 inputs, and changed the...
Hi,
I would like to check battery level using the SAADC of the nrf52840.
Assuming the voltage is less than 3.6V, do I need to have a resistor between the battery and the...
HI,
I am new to IoS development with NRF.
I am having NRF52840 DK, IoS device. I want to implement USB HID device application (similar to pulse/Gluco meter ) on IOS. I...
Hi,
I am not able to compile the SDK example by using SES for ARM V3.52.
I got one error which shown below:
It pointed to the link ldr r0, =%4
Thanks
Gan
Hi,
I am using fatfs of nRF5_SDK_15.0.0_a53641a.
I am writing a program with keil.
I am currently doing SPI communication with BLENanov2(nRF52832) and SD card with...
Hi,
I am implementing the UART on NRF52840. TX works but the RX doesnot. While debugging, I noticed that STARTRX task register is not getting set due to which the RXDRDY...
