Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
We are develop one product, it is power by four AA battery. It works fine. but now I found a problem. when I power off and then power on again, sometime it can not be reset...
when I start ADC the current will be HIGH .even I UN-Initialization it .
what I have done like that below；
before I started it The current is 0.6ma
but when I start...
I'm trying to communicate with a device over UART, and I'd like to return the response to my commands back to the function the transmission came from.
For example, I want...
I want to develop nrf52840 with ble mesh topology.
However I need one node to transmit data received from all the nodes via uart to a gsm module
Can anyone please tell...
Hello Nordic experts,
I am trying to use app_usbd_ep_enable and app_usbd_ep_disable in order to enable/disable an endpoint. I need this to fake usb unplug/re-plug. Currently...
Hello. I am testing the sending and receiving of UART using nRF 52840-DK. If you change the UART pin settings as follows, you can receive but you can not send. It is confirmed...
Although I have already seen this discussion ( https://devzone.nordicsemi.com/f/nordic-q-a/35183/no-idea-how-to-get-manufacturer-specific-data-in-central-side-from-advertising...
Hello,
I have an nRF52840 chip ( Holyiot nRF52840 module ) and I want to program the chip using an nRF52840 DK. The Holyiot module is basically an nRF52840 mounted on a...
I am having trouble turning on bonds for DFU.
First of all, before I describe this pain, can I choose to avoid this battle by just allowing unbonded devices to DFU? e.g...
Hello!
I just bought the Beacon Kit and i was following the user guide v1.1 and I have some questions about how to use DFU. I have already downloaded nRF Toolbox app.
...
Hi,
I am using fatfs of nRF5_SDK_15.0.0_a53641a. I am writing a program with keil.
I want to know how to write the value obtained from the sensor to the SD card. ...
I am using proximity profile in sdk15 with softdevice 6.0.0 . I added flash write, writing continuously some data to flash. But it working sometimes only.
Hello,
at the moment my application is accepting more than one device if its not connected to anything. But I want that the application only connects to one device and...
