I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Can the nRF2460 be operated with TXLAT (0x52) set to a value lower than 4 ?
Can the nRF2460 have a lower latency than 20mS ?
The range requirements are very small (30...
Hi All,
I have created a custom board header file based off of the pca10040.h file. I have customised this to support 10 buttons and 2 leds. I have also extended the array...
Hi everyone ;)
I have a problem with timeslot ESB library with Bluetooth LE. In my application i need do somethingh like that:
Bluetooth and ESB PRX works excelent...
Hi, I am using the BLE mesh 2.2.0 with nRF5_SDK_15.0.0_a53641a. I am using Segger embedded studio as toolchain. I was able to compile and flash the default app code onto NRF52...
I am working on an application to connect approximately 500 devices in a single network... trying to check if Thread or Mesh is a better option... Please do suggest...
After searching around a little bit I found this post, but sadly an answer did never come up apparently. I'm using the nrf52 DK, using the 132 Softdevice.
I'm kind of at...
Hi every one!
I have nRF52840 dongle and BMD-300 Series Evaluation kit featuring the nRF52832.
I`d like to transmit continuous signals from nRF52832 to dongle(Desktop...
I have two ble boards（board A and B）, one for client(Board A) and the other serve as slave(Board B). now i want to use board A to upgrade the application of board B by OTA...
Hi,
i would like to use the Power Profiler v2.0.0 from nRF Connect Software. The Power profiler is connected and it works with the Software 1.0.0. When i launch the power...
Hello,
I want to configure de coded mode on my nRF52DK, using the ble_app_interactive. How can I do it ?
I've saw that I can set the coded mode by de CENTRAL to a PEROPHERAL...
Hi,
I designed my custom board with RF52832. I was able to detect my board using the debugger.
I am using the BLE mesh default "Light switch proxy server".
I could get...
Hello, I got stuck developing with the nrf52840 DK Board, using the ZigBee SDK.
I´ve got a corrdinator, which establishes my network. Also I´ve got an End-Device that joins...
Hi,
I'm trying to relate the package marking to the IC revision or more specifically to the relevant errata sheet.
The documentation mentions the fields <PP><VV><H...
hello support ,
when I add the following code to ble_app_hrs example under the function advertising_init() there is no Advertising from the DK
What could be problem ?...
