I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Hello, I'm currently attempting to display a screen during an OTA-DFU process. First and foremost, through BLE, a BLE Central will command my BLE Peripheral to commence DFU...
I am working with NRF52832 master with TWI slave device, however , since our board already has external pull-up resistors (10K) , how do I disable TWI internal pull up resistors...
Hi nordic
I am using SDK 14.2.0 Softdevice s332 5.0 Board nrf52840.
I am doing test about DFU example and I am writing in flash about test image.
It is possible. I made...
Hello.
We have a working DFU system using Nordic's Secure Buttonless DFU bootloader. The bootloader correctly checks if the incoming DFU package has the correct 'init packet...
Hi all,
I am curious about the storage capabilities of the Nordic Thingy. I would like to store information about the received messages like a timestamp. How much data can...
So, here is an interesting and fun one: I am using a module with the nRF52832 to control an LED driver with a PWM, we
According to the documentation http://infocenter...
I am starting to use FDS for saving data to flash memory. In the "flash_fds" example the macro APP_ERROR_CHECK() is used to check for errors in most of the function calls...
Hello,
I tried to send data through the proprietary radio. My devices are NRF52832. The data I would like to send is an uint8_t array:
Right before I send it out, I...
Hi everyone,
My English skill is not good, but I really want to share this problem to all developers that I spent three hours for it.
Example nRF5_SDK_for_Thread_and_Zigbee_2...
Hi!
I have questions for Nordic developers team. What capacity of network is possible with nrf52840 thread mesh? I've tried to attach large amount of nodes to mesh and...
Hi Guys,
I want to use the TWI for my mesh application in which I want to read out 2 sensors (Sensirion SHTW2 and SGCP3) and then send the sensor values over a mesh network...
Hi all,
I´m using nrf52832 with sdk 14.2.0 and softdevice s332.
I have opened and closed the eclipse. Now when I open it, it compiled and gives me this error that I did...
Hi,
I am using nRF_SDK_15.0.0?a53641 and writing a program with keil.
I am trying to read data from the acceleration sensor( LSM303DLHC ) by communication with BLENanov2...
Hello
I just started learning nrf52832 DK and run few of the examples. I wanted to start developing my own application based on the examples. Right now, I want to read...
Hello, I have some confusion about updating advertising packet dynamically.
I am using nrf52832 with SDK v12.3.0. I am sending datas from sensor in advertising packet(manuf...
